Operation Manual - Cinemills Corporation
Contents
1. Operation Manual IMPORTANT INFORMATION Warnings and Notices When using electrical equipment basic safety precautions should always be followed including the following a Read and follow all safety instructions b Do not use outdoors c Do not mount near gas or electric heaters d Equipment should be mounted in locations and at heights where it will not readily by subjected to tampering by unauthorized personnel e The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition f Do not use this equipment for other than intended use g Refer service to qualified personnel SAVE THESE INSTRUCTIONS WARNING You must have access to a main circuit breaker or other power disconnect device before installing any wiring Be sure that power is disconnected by removing fuses or turning the main circuit breaker off before installation Installing the device with power on may expose you to dangerous voltages and damage the device A qualified electrician must perform this installation WARNING Refer to National Electrical Code and local codes for cable specifications Failure to use proper cable can result in damage to equipment or danger to personnel WARNING This equipment is intended for installation in accordance with the National Electric Code and local regulations It is also intended for installation in indoor applications only Before any electrical work is performed disconnect power at2. 3 2 Connecting Power 3 2 1 Connecting to AC Power Direct connection to an AC power source using an included AC input cable A arm aun dace s masmanta e Figure CINESOFT LED Luminaire AC Input Connection 3 2 2 Connecting to DC Power Direct connection to a DC power source i e AC to DC converter or battery through the fixture s DC input 3 pin XLR connection PIN 1 GND PIN 2 22 34V PIN 3 Not Used DMX 512 DC 22 34V Figure CINESOFT DC Input Connection Page 9 Operation Manual CINESOFT m LED LUMINARIES 3 3 Accessories Installation 3 3 1 Barn door Installation The CINESOFT LED luminaire can be provided with barndoors as an option sold separately in a set of four To install a barndoor assembly position the barndoor alongside the extruded edge of the luminaire Align the thumbscrews with the adjustable receptacle holes in the luminaire and insert into place Lock the barndoors by turning the silver thumbscrew To remove a barndoor assembly reverse the order of the installation process Figure Barn door installation 3 3 2 Honey comb Installation Turn the four screws located on the corner in order to fix the Honey comb Figure Honey comb installation Page 10 Operation Manual CYIMSSOYZT m L ED LUMINARIES 3 4 Connecting to the DMX 512 Network The topology configuration corresponds to daisy chain cabling therefore the fixtures have an input and an output port Five p
3. 4 2 3 The third procedure Control via the DMX signal 4 3 To Adjust the Dim Level Setting 4 3 1 The first procedure control via the Dimmer jog wheel 4 3 2 The second procedure control via the DMX signal 4 4 Get into the DMX address mode and set of the DMX addresses 4 5 Set the Lock Mode 4 6 To adjust the CCT and Dim level setting in DMX control mode 4 6 1 DMX mapping to DIM level 4 6 2 DMX mapping to CCT level 5 TECHNICAL DATA 5 1 Part No System 5 2 Common Specifications 5 3 Individual Specifications 5 3 1 Basic Specification 5 3 2 Photometric Data Luminous intensity standards 5 3 3 View Angle amp Luminous Intensity 5 3 4 Outline Dimension Page 4 Operation Manual COMS m LE D LUMINARIES 1 PREFACE 1 1 About this Manual The document provides installation and operation instructions for the following products X Soft Panel LED Luminaire CINESOFT Please read all instructions before installing or using this product 1 2 Included Items Each Soft Panel LED Luminaire CINESOFT includes the following items X Soft panel LED lighting fixture X Yoke Mount assembly X AC power input cable X User s manual this document 1 3 Accessories Contact your authorized dealer for price and availability of all accessories for the CINESOFT series Additional information can be found on our web site at www cinemills com X Barn door X Honeycomb Page 5 Operation Manual COMES m L ED LUMINARIES 2 CINESOFT
4. it is possible to change the fineness of the adjustment of Dim level In DMX ADDRESS mode a LCD display Provides information about DMX address of channel 1 and channel 2 e Color jog wheel Set the DMX address for channel 1 CCT level control f Dimmer jog wheel Set the DMX address for channel 2 bright intensity level control Page 7 Operation Manual OMESSA m C E D LUMINARIES 2 1 3 Connection Ports and Power Switch Figure CINESOFT Connections a AC Power inlet IEC 320 C14 Receive AC power through the power cord b Fuse holder Replace the fuse c Rocker switch Power on and off d DMX IN Receive DMX signals It consists of the 5P XLR Male Panel Mount connector e DMX OUT Transmit DMX signals It consists of the 5P XLR Female Panel Mount connector f DC power inlet Receive DC power from the DC power supply unit power station etc 2 1 4 Accessories Figure Barn doors Figure Honey comb Page 8 Operation Manual CIMESOZT m E ED LUMINARIES 3 INSTALLATION 3 1 Main Power Requirements The CINESOFT Luminaire can be connected to an AC or DC power input for operation When connected to an AC power the fixture operates on 100 to 230 volts AC The luminaire has a built in auto ranging power supply and an on board on off switch Also when connected to a DC power the fixture of 100W operates on 24 volt DC through 3 pin XLR and the fixture of 200W operates 48 volt DC through 3 pin XLR
5. OVERVIEW 2 1 CINESOFT Components 2 1 1 Major CINESOFT Components Figure CINESOFT Front View CiNEMILI ener CINE S Of sor 30m umas n4 MIP sa moop Figure CINESOFT Rear View A Accessory holders 4 point Can be hung by a rope etc B Carrying handle Used to carry and angle adjustment of the CINESOFT C T grip Tighten and loosen the Yoke D On board control panel Operates the function of the CINESOFT E Yoke Attach the luminaire with mounting accessories and adjust the angle of the CINESOFT Page 6 Operation Manual OMESSA m L E D LUMINARIES 2 1 2 On board Control Panel including LCD Display The CINESOFT s control panel with LCD panel provides local control for accessing each of the functions The shape and features of each element are as follows 2800K 3200K 4000K 5000K 5600K h N M Color Dimmer Figure On board control panel and LCD display In general mode a LCD display Provides information about CCT and brightness level and the status of the Lock mode b DMX ADDRESS Enter the DMX address setting mode c CANCEL LOCK Save and exit from the DMX ADDRESS setting mode press the button once Enter the LOCK mode press and hold about 2 seconds d CCT Preset Turn on the pre set CCT It consists of five preset buttons e Color jog wheel Manually adjusts CCT levels f Dimmer jog wheel Manually adjusts bright intensity levels In addition
6. the circuit breaker or remove the fuse to avoid shock or damage to the control It is recommended that a qualified electrician perform this installation Additional Resources for DMX512 For more information on installing DMX512 control systems the following publication is available for purchase from the United States Institute for Theatre Technology USITT Recommended Practice for DMX512 A Guide for Users and Installers 2 edition ISBN 9780955703522 USITT Contact Information Cinemills Fae ae Jor O coln Operation Manual CIMESOFLT m ERD LUMINARIES TABLE OF CONTENTS IMPORTANT INFORMATION TABLE OF CONTENTS 1 PREFACE 1 1 About this Manual 1 2 Included Items 1 3 Accessories 2 CINESOFT LUMINAIRE OVERVIEW 2 1 CINESOFT Luminaire Components 2 1 1 Major CINESOFT Components 2 1 2 On board Control Panel including LCD Display 2 1 3 Connection Ports and Power Switch 2 1 4 Accessories 3 INSTALLATION 3 1 Main Power Requirements 3 2 Connecting Power 3 2 1 Connecting to AC Power 3 2 2 Connecting to DC Power 3 3 Accessories Installation 3 3 1 Barn door Installation 3 3 3 Honey comb Installation 3 4 Connecting to the DMX 512 Network 3 4 1 DMX I O Pin Signal Define 3 4 2 DMX Cables Page 3 Operation Manual 4 OPERATION 4 1 Turning on 4 2 To Adjust the CCT Level Setting 4 2 1 The first procedure control via the preset buttons 4 2 2 The second procedure control via the CCT jog wheel
7. l panel are ignored and the state of step 2 is displayed 4 6 To adjust the CCT and Dim level setting in DMX control mode This section contains information for operating the luminaire using DMX control in 8 Bit DMX512 mode Dim levels D55 0 100 1 or 5 increments ee CCT levels 0 255 2800K 5600K 50K increments Note 1 Do not select equally DMX CCT ID amp Dimmer ID Note 2 Can t operate the fixture through on board control with the DMX cable plugged in 4 6 1 DMX Address 2 is for dimming change 4 6 2 DMX Address 1 is the initial default setting value for CCT Change Page 16
8. ocedures for setting The first is to use the jog wheel through onboard control panel and the second is through the DMX control scheme 4 3 1 The first procedure control via the Dimmer jog wheel Step 1 Press the Dimmer jog wheel to toggle between fine and coarse adjustments Fine adjustment can be adjusted in units of 1 Coarse adjustment can be adjusted in units of 5 Step 2 Rotate the Dimmer jog wheel to desired bright intensity level in range from 0 to 100 Turn clockwise The bright intensity level is increased by 1 or 5 Turn counter clockwise The bright intensity level is decreased by 1 or 5 cw X CCW EDan Step 3 The luminaire is turned on the selected Dim level Step 4 The selected value is displayed on the LCD display E a PAAA BRIGHTNESS S92 4 3 2 The second procedure control via the DMX signal For details see the DMX control page Page 14 Operation Manual GCINESOFT m EE LUMINARIES 4 4 Get into the DMX address mode and set of the DMX addresses The CINESOFT luminaire has two channels for DMX control The first is for adjusting the CCT level and the second is for adjusting the DIM level Step 1 Press the DMX ADDRESS button to enter DMX address setting mode Step 2 The last DMX address setting is displayed on the LCD display Step 3 Turn the Color jog wheel in order to select the DMX address for CCT level control channel or turn the Dimmer jog wheel in order to
9. ole XLR plugs are used for cabling Figure DMX 512 network configuration 3 4 1 DMX I O Pin Signal Define DMX pin out wiring follows the USITT DMX standard Shield Gnd Shield Gnd Pass thru 1 1 Pass thru 2 2 4 4 Pass thru 3 3 5 5 Pass thru 2 2 4 4 Pass thru 3 3 5 5 3 4 2 DMX Cables The CINESOFT uses five pin XLR connectors to receive DMX signals from the external DMX console In this case the DMX cable connecting the two devices Ends of the cable consist of each XLR male and female connector It is also used to transmit and receive DMX signals between fixtures in a series Page l 11 Operation Manual OMES LED LUMINARIES 4 OPERATION The CINESOFT luminaire has two main features as a light fixture This includes the setting of the desired CCT and brightness These features are available through the control panel on fixture or the external devices such as DMX sliders The procedures for using these features are introduced below 4 1 Turning on After you have turned on the power switch the fixture will need a short start up time before it lights up Step 1 Make sure the fixture is powered Step 2 Turn on the power switch Step 3 The luminaire will light up with the last set value The information about the fixture are displayed sequentially on the LCD display The last setting is displayed after the boot is complete If DMX is enabled indicates the last setting DMX address TGLeV
10. select the DMX address for Dim level control channel Each the DMX address range is from 1 to 512 Turn clockwise The DMX address value is increased by 1 Turn counter clockwise The DMX address value is decreased by 1 cw N fe es CCW EDan Step 4 The selected DMX address settings are displayed on the LCD display as shown below E A D M X A Ep BRETDMATID Step 5 Press the DMX ADDRESS button again to save the assigned DMX address and exit from the DMX address setting mode Note1 Do not select the same DMX address value in the each channel DMX address setting Page 15 Operation Manual GINSSOPT LUMINARIES 4 5 Set the lock mode In general mode you can press and hold the cancel button for 2 seconds to enter the onboard control lock mode Even though any operations that feature does not work Only the external input DMX signal can control for only the CCT and Dim levels Repeat the same procedure to release the lock Step 1 Press and hold the CANCEL LOCK button for about 2 seconds to enter the onboard control LOCK mode Step 2 As shown below this is displayed on the LCD display for approximately 2 seconds Tut 3200K BUTTON LOCKED Step 3 To release the LOCK mode perform the step 1 operation again Step 4 As shown below this is displayed on the LCD display for approximately 2 seconds E a a 3200K BUTTON UN LOCK Note1 In LOCK moade all input on the contro
11. vVaiee FLASHER Table Tut ZS00K B A G AEN ESSE 5 0 Note1 When the power is turned off or removed the fixture will remember its last setting Page 12 Operation Manual GCYINESO FT m LED LUMINARIES 4 2 To Adjust the CCT Level Setting There are three procedures for setting The first is to use the Pre set buttons and the second is to use the jog wheel through onboard control panel The third is through the DMX control scheme 4 2 1 The first procedure control via the preset buttons Step 1 Press the desired CCT Preset button CCT The preset buttons are as follows CCT preset button 2800K 3200K 4000K 5000K 5600K Step 2 The luminaire is turned on the selected preset CCT level Step 3 The selected value is displayed on the LCD display Tid A 0 0 OK B R EGAN ESSE ALO O0 4 2 2 The second procedure control via the CCT jog wheel Step 1 Rotate the CCT jog wheel to desired CCT level in range from 2800K to 5600K Turn clockwise The CCT level is increased by 50K Turn counter clockwise The CCT level is decreased by 50K Step 2 The luminaire is turned on the selected CCT level Step 3 The selected value is displayed on the LCD display E a A SOK B R E GATEN ESSE EEO O 4 2 3 The third procedure control via the DMX signal For details see the DMX control page Page 13 Operation Manual CINESOFT m LE D LUMINARIES 4 3 To adjust the Dim level setting There are two pr
Download Pdf Manuals
Related Search