User Manual - DTC
Contents
1. Diversified Technologies ttc Corporate Office 2 West Main St Victor NY 14564 585 461 2110 DTC 2D E02 Ethernet Interface User s Manual F 3 Ni J l Il Aug 2013 Rev A O Copyright and Disclaimer Copyright 2013 All rights reserved Diversified Technologies LLC 2 West Main St Victor NY 14564 Tel 1 585 461 2110 The information contained herein is proprietary and is provided solely for the purpose of allowing customers to interface to and operate the Microscan MS 2D scan engine and is not to be released reproduced or used for any other purpose without written permission of Diversified Technologies LLC Throughout this manual trademarked names might be used We state herein that we are using the names to the benefit of the trademark owner with no intention of infringement Disclaimer The information and specifications described in this manual are subject to change without notice Technical Support For technical support visit www DTC 2D com or call 1 585 461 2110 during regular business hours EST Warranty and Terms of Sale For Standard Warranty information see www DTC 2D com warranty htm Diversified Technologies LLC or its subsidiaries does not warrant and shall not be responsible for any lost data or images contained in any product including in any returned product regardless of the cause of the loss Diversified Technologies LLC s2. Stop Bits E Send Frame Immediate Yes No Send Trailing Bytes None One Two Flush Mode Flush Input Buffer With Active Connect C Yes No Flush Output Buffer With Active Connect C Yes No With Passive Connect C Yes No With Passive Connect Yes No At Time of Disconnect Yes No _ At Time of Disconnect Yes No The Serial Settings page will allow you to change the Xport s serial port settings Caution The serial settings of the Xport must match that of the MS 2D engine If not you will not be able to communicate with the scanner If you need to change the scanner settings do that first with ESP software then change the Xport serial settings to match those of the MS 2D engine When done click the OK button at the bottom and then click the Apply button to finish DTC 2D E02 Ethernet Interface User s Manual 11 Running the Lantronix Devicelnstaller setup program Continued Web Configuration Serial Handshake Settings Address http 192 168 56 90 secure Itx_conf htm z O0 6 MAC Address 00 20 4A EA 6F 6D LANTRONIX TEA on Configurable Pin Settings Network Server Serial Tunnel Function Direction Active Level pa am HW Flow Control Out gt Input Output Low High Serial Settings General Purpose I O gt input C Output Low C High Connection Email HW Flow Control In gt amp Input Output Low High Trigger 1 Trigger
3. Yes No LED Blink gt Disconnect Mode On Mdm_Ctrl_in r Drop C Yes No Check EOT Ctr D C Yes No Hard Disconnect Yes No Inactivity Timeout o o mins secs The Default port used in the ESP programming software is 2001 as seen above This page allows full control of this aspect if desired When done click the OK button at the bottom and then click the Apply button to finish DTC 2D E02 Ethernet Interface User s Manual 13 DTC 2D E02 Specifications x GOOD READ Ee C Po J RoHS de J2 D Ji 1 350 0 985 D D 0 895 CTS ea i E ESD1 OOO ol l INCHES IZO000 1 535 i DTC 2D E02 Specifications Power In External 5 VDC Reverse Polarity Protected Current Draw w Scanner 2 8 watt 550 mA Max 210 mA typical Dimensions 0 98 in D x 1 53 in W x 0 63 in H 25 x 39 x 6 4 mm Weight 14 grams Operating Environment 4 to 50 C 0 to 131 F 5 95 RH non condensing Host Interface TCP IP Ethernet RJ 45 User Interface Molex 8 pos socket for trigger and 1 0 J2 POWER and 0 CONNECTOR RJ 45 ETHERNET INTERFACE y A Netuea Lm zeie el mmeo wow JEA oo 0 3 GOOD READ LOW 31 Ra Board Plug View 4 WAKE UP LOW 6 RK Power Down Signal ot 2D CBL03 e Beep LOW 4 Not Used Terminated EE CIN 5 Not Used Terminated VO CONNECTOR 7 Not Used Terminated 8 DC GROUND 6 N
4. first install the XportTM device installer application included with this product Below is the Windows 7 installation screen sequence for Web_ setup exe the Lantronix Device Configuration installer program Do you want to run this file Name rt_Data Device_Installer_4_3_0_5 Web_setup exe Publisher Lantronix Inc Type Application From D _ACTIVE_PROJECTS TLC MS_2D Design Data L Aan cena V Always ask before opening this file While files from the Intemet can be useful this file type can D potentially harm your computer Only run software from publishers 7 youtrust What s the risk The NET framework 4 is required 2 Devicelnstaller Installer on In order to install Devicelnstaller you must first install these components Microsoft NET Framework 4 0 x86 x64 Download Install V Devicelnstaller 4 3 0 5 x86 English Windows 7 x86 T se The installer will then download the latest files gt Devicelnstaller Download Components Devicelnstaller 4 3 0 5 x86 English Installing Devicelnstaller 4 3 0 5 x86 English Wait this operation could take some time Download File Devicelnstaller 4 3 0 5 x86 English 2 9MB of me e os ODIO iit DTC 2D E02 Ethernet Interface User s Manual 4 Lantronix Device Installer Installation Continued After extracting itself the Lantronix Device Installer Setup program wil
5. use Windows Update to check for any critical updates to the NET Framework Cancel Running the Lantronix Devicelnstaller setup program In the Windows Start Menu you will find the Lantronix folder as seen below Double Left click on the Device Installer icon to launch the application d Lantronix s Devicelnstaller 4 3 Devicelnstaller Help me Devicelnstaller al Release txt lf your machine does not have any detectable serial ports you will get the following message Click OK to continue Application Startup Warnings WARNING No serial ports were found on this PC Atleast one serial port is necessary to recover a device server over a serial port Do not prompt me about this Can enable this again from Tools gt Options The main window will appear as seen below gt S Lantronix Devicelnstaller amp 3 0 5 File Edit View Devi Tools Help J Search amp Exclude Assign IP s Lantronix Devices 0 device s Name Group IP Address Status 2 Local Area Connection 192 168 56 101 Fa Ready Initially the Devicelnstaller searches for devices If no devices yours are found as seen above you will need to assign or change the IP address of the DIC 2D E02 To do this left click on the Assign IP icon as seen above DTC 2D E02 Ethernet Interface User s Manual Running the Lantronix Devicelnstaller setup program Continued Assign IP Address wizard If you selected Assign IP Add
6. 2 Trigger 3 Apply Settings Apply Defaults If your application requires hardware a hand shake with the MS 2D engine change the MS 2D engine settings first with ESP software then set the Configurable Pins CPO and CP2 to RTS and CTS respectively as seen above When done click the OK button at the bottom and then click the Apply button to finish DTC 2D E02 Ethernet Interface User s Manual 12 Running the Lantronix Devicelnstaller setup program Continued Web Configuration TCP Port Settings Device Details Web Configuration Teinet Configuration Aes 20 93 LANTRONIX Network Server Serial Tunnel Hostlist Channel 1 Serial Settings Email Trigger 1 Trigger 2 Trigger 3 Configurable Pins Apply Settings Apply Defaults Channel 1 Connect Protocol Protocol TCP gt Connect Mode Passive Connection Accept Incoming Password Required Password Modem Escape Sequence 3 Pass Through Yes No Yes C Yes No Endpoint Configuration Remote Port o Common Options Telnet Com Port FE Cntr Disable gt Firmware Version V6 7 0 1 MAC Address 00 20 4A EA 6F 6D Connection Settings Active Connection Active Connect None Start Character 99D in Hex Modem Mode None gt Show IP Address After RING Yes No Auto increment for active connect Remote Host 0 0 0 0 Connect Response None gt Terminal D Use 3 N Name Hostist
7. ain IP address automatically Auto Configuration Methods BOOTP Enable Disable DHCP Enable Disable AutolP Enable Disable sal DHCP Host Name Use the following IP configuration IP Address 192 168 56 90 Subnet Mask 255 255 2550 Default Gateway booo DNS Serer 0000 Xrort Ethernet Configuration IV Auto Negotiate Speed 100 Mbps 10 Mbps Duplex Full Half x q Continued The Network Settings page will allow you to change the Xport s external IP settings When done click the OK button at the bottom and then click the Apply button to finish Afterwards re search to update the Devicelnstaller tree view DTC 2D E02 Ethernet Interface User s Manual 10 Running the Lantronix Devicelnstaller setup program Web Configuration Serial Settings Device Details Web Configuration Telnet Configuration Continued Network Server Senal Tunnel Hostlist Channel 1 Connection Email Trigger 1 Trigger 2 Trigger 3 Configurable Pins Apply Settings Apply Defaults TEEPE LANTRONIX O secure itx_conf htm Firmware Version V6 7 0 1 MAC Address 00 20 4A EA 6F 6D Serial Settings M Disable Serial Port Port Settings Protocol RS232 Baud Rate 115200 Data Bits 8 Parity None Pack Control I Enable Packing Idle Gap Time 12 msec Match 2 Byte Sequence Yes No Match Bytes oxf00 oxf00 Hex Flow Control None
8. dude Assign IP Upgrade Lantronix Devices 1 device s gig INTEL 192 168 56 101 XPot XPort 03 04 firmware v6 7 0 1 se 192 168 56 90 Please press the Go button to navigate to the device There is no password assigned in the module when shipped Change it at your own risk Click OK to proceed Windows Security x The server 192 168 56 90 at null requires a username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection LA DTC 2D E02 Ethernet Interface User s Manual 9 Running the Lantronix Devicelnstaller setup program Web Configuration wizard Continued This is the home page for your device From here you can change all aspects of the Lantronix XPort module LANTRONIX yen cae Network Server Serial Tunnel Hostlist Channel 1 Serial Settings Connection Email Trigger 1 Trigger 2 Trigger 3 Configurable Pins Apply Settings Apply Defaults Device Server Configuration Manager Version 1 8 0 1 Web Configuration Network Settings Serial Tunnel Channel 1 Serial Settings Connection Email Trigger 1 Trigger 2 Trigger 3 Configurable Pins Apply Settings Apply Defaults Firmware Version V6 7 0 1 MAC Address 00 20 4A EA 6F 6D Network Settings Network Mode Wired Only IP Configuration C Obt
9. e Close connector Caution The connector housing and clamp mechanism are fragile Attaching the DTC 2D E02 interface to your host system To attach the DTC 2D E02 Interface to your host plug a cat 5 cable from your network into the DTC 2D E02 and use the Molex I O connector block interface a seen below J2 POWER and 1 0 CONNECTOR RJ 45 ETHERNET INTERFACE y 1 Notused in 8 2 TRIGGER LOW D oo 3 GOOD READ LOW WAKE UP LOW TX TX RX kX Not Used Terminated Board Plug View 5 Power Down Signal D CBLO3 6 Beep wow VO CONNECTOR e oc erou Not Used Terminated Not Used Terminated CS En in Fes Not Used Terminated od Chassis Ground If your purchase included an MS 2D scan engine the scanner communications have been preset to 115 2 Kb No Parity 8 Data bits 1 Stop bit DTC 2D E02 Ethernet Interface User s Manual 2 O Host Communications The DTC 2D E02 is a CMOS TTL to Standard Ethernet interface converter for the MS 2D engine All other I O and control signals are passed through directly The DTC 2D E02 Ethernet interface is preset at the factory with the following settings RS 232 port to MS 2D Enabled 115 2 Kb 8 Data bits No parity 1 stop bit No flow control Ethernet Port Static IP 192 168 56 90 Subnet 255 255 255 0 Gateway Port 2001 The DTC 2D E02 s IP address is statically set f
10. erial Settings o Handshake Settings o TCP Port Settings DTC 2D E02 Specifications Appendix 1 Common MS 2D Data Matrix Configuration Symbols DTC 2D E02 Ethernet Interface User s Manual 10 12 13 14 15 DTC 2D E02 Ethernet interface card i Port i th lh 4 Il l Getting Started Caution Be sure that all cables are connected BEFORE applying power to the system Always power down BEFORE disconnecting any cables Important The DTC 2D E02 and Microscan MS 2D scan engine are intended for connection to a UL listed direct plug in power unit marked Class II and rated 5 VDC at 5 Watts or greater if using additional I O and or electrical accessories Package contents Item Part Number DTC 2D E02 Ethernet Interface card DTC 2D E02 DTC 2D E02 Ethernet Interface User s Manual O Attaching the DTC 2D E02 interface card to the MS 2D scan engine To attach the included 2 inch flexible interface cable to the scanner engine board first slide the end of the ribbon cable with exposed tin leads facing the circuit board upward into the housing Then carefully push the ZIF connector hinged clamp mechanism downward so that it covers the contact points as seen below Do the same thing for the end of the flex cable that attaches to the 2D S01 interface card As shown below Again the exposed tinned leads must be facing the circuit card downward Open Insert flex cabl
11. l run 45 Lantronix Devicelnstaller 4 3 0 5 x86 Welcome to the Lantronix Devicelnstaller 4 3 0 5 x86 Setup Wizard The installer will guide you through the steps required to install Lantronix Devicelnstaller 4 3 0 5 x86 on your Computer WARNING This computer program is protected by copyright law and international treaties Unauthorized duplication or distribution of this program or any portion of it may result in severe civil or criminal penalties and will be prosecuted to the maximum extent possible under the law J Lantronix Devicelnstaller 4 3 0 5 x86 Confirm Installation The installer is ready to install Lantronix Devicelnstaller 4 3 0 5 x85 on your computer Click Next to start the installation Devicelnstaller Installer i Devicelnstaller installed successfully This completes the Lantronix Device Installer application DTC 2D E02 Ethernet Interface User s Manual J Lantronix Devicelnstaller 4 3 0 5 x86 Select Installation Folder The installer will install Lantronix Devicelnstaller 4 3 0 5 x86 to the following folder To install in this folder click Next To install to a different folder enter it below or click Browse Folder C Program Files Lantronix Devicelnstaller4 3 Disk Cost 45 Lantronix Devicelnstaller 4 3 0 5 x86 Installation Complete Lantronix Devicelnstaller 4 3 0 5 x86 has been successfully installed Click Close to exit Please
12. ller setup program Continued Assign IP Address wizard Continued To complete the assignment click the finish button Click the Assign button to complete the IP address assignment Progress of task After assignment you will be able to see your device in the tree and main view of the Devicelnstaller program eT Z Lantronix Devicelnstaller4305 0 a i File Edit View Device Tools Help p Search Exclude AssignIP Upgrade Bp Leon Devices device Device Detais Web Configuration Telnet Configuration gg Local Area Connection 192 168 1 101 Reload Details o Xot P2 RI gr A8 XPort 03 04 fimware v6 7 0 1 192 168 56 90 XPort XPort 03 04 x5 00 20 4A E8 9D 37 6 7 6 7 0 1 Online 192 168 56 90 DTC 2D E02 Ethernet Interface User s Manual 8 Running the Lantronix Devicelnstaller setup program Continued Web Configuration wizard With your DTC 2D E02 powered and connected to the network select your device in the tree view and then left click on the Web Configuration tab Lantronix Devicelnstaller 4 3 0 5 File Edit View Device Tools Help Search Exclude Assign IP Upgrade Sa Lantronix Devices 1 device s Device Details Web Configuration Tenet Configuration g Local Area Connection 192 168 1 101 i SO XPot g Reload Details EEE N EE g Nae Ca A NHCP Navire Name Plies File Edit View Device Tools Help yp Search Ex
13. or those cases where a DHCP server is not available during configuration If you are using a Null Cat 5 connection or you need to change the IP address of the module it will be necessary to first temporarily change your local adapter settings to be compatible with the DTC 2D E02 s subnet After which you can restore your local adapter s settings Alternately it is recommended that you use the Assign IP Address wizard as described in the Section Assign IP Address wizard or Web Configuration Ethernet Settings if the 2DE01 is not on your local subnet or you want to change it 2 If your MS 2D is not correctly configured for serial operations or you want to change serial parameters refer to the Section Web Configuration Serial Settings After initially applying power to the DTC 2D E02 Ethernet interface and if the MS 2D is configured correctly to match the RS 232 comm parameters of the DTC 2D E02 you will immediately be able to communicate with the MS 2D scanner 192 168 056 90 on port 2001 If your MS 2D is not correctly configured for serial operations or you want to change serial parameters refer to the Section Web Configuration Serial Settings For additional information on the MS 2D please read the Microscan MS 2D Engine User s Manual or visit www Microscan com DTC 2D E02 Ethernet Interface User s Manual 3 Lantronix Device Installer Installation To configure the Ethernet port on the DTC 2D E02 interface you must
14. ot Used Terminated Sh Chassis Ground DTC 2D E02 Ethernet Interface User s Manual 14 Appendix 1 Common MS 2D Data Matrix Configuration Symbols MO149_O1 RS 232 Raw Mode Default MO027 01 MO0026_01 Moo25 01 Moo24 01 RS 232 115200 Baud Default RS 232 57600 Baud RS 232 38400 Baud RS 232 19200 Baud MO023 01 M0019 01 Moo1s_ 0 RS 232 8 Data Bits RS 232 9600 Baud Default RS 232 7 Data Bits M0030 01 MOIS Ol M0029 01 RS 232 No Parity Default RS 232 Even Parity RS 232 Odd Parity M0031 01 M0032 01 UART Flow Control UART Flow Control None Default Hardware DTC 2D E02 Ethernet Interface User s Manual 15 Appendix 1 Common MS 2D Data Matrix Configuration Symbols Continued M0136 02 M0138 02 M0139 02 Postamble CR Postamble LF Postamble CR LF Serial Only Serial Only Serial Only M0166 01 Save Settings For the full command set refer to the Microscan MS 2D Scan Engine User s Manual P N 84 000008 Rev A DTC 2D E02 Ethernet Interface User s Manual 16
15. products are not warranted to operate without failure Diversified Technologies Inc products must not be used in life support systems or other applications where failure could threaten injury or life THE DTC 2D S01 SERIAL INTRFACE IS NOT DESIGNED MANUFACTURED OR INTENDED FOR USE OR RESALE AS ON LINE CONTROL EQUIPMENT IN HAZARDOUS ENVIRONMENTS REQUIRING FAIL SAFE PERFORMANCE SUCH AS IN THE OPERATION OF NUCLEAR FACILITIES AIRCRAFT NAVIGATION OR COMMUNICATION SYSTEMS AIR TRAFFIC CONTROL DIRECT LIFE SUPPORT MACHINES OR WEAPONS SYSTEMS IN WHICH THE FAILURE OF TECHNOLOGY COULD LEAD DIRECTLY TO DEATH PERSONAL INJURY OR SEVERE PHYSICAL OR ENVIRONMENTAL DAMAGE DTC 2D E02 Ethernet Interface User s Manual O Statement of agency compliance The DTC 2D S02 conforms to the following Product Specifications FCC Compliance FCC Part 15 Subpart B The DTC 2D S02 is RoHS compliant This certification applies to the DIT C 2D S02 as a stand alone OEM industrial product and does not apply to the DTC 2D S02 as an integrated module When integrating the DT C 2D S02 into another product that product will still need to obtain any applicable certifications for the full or final product IMPORTANT The DTC 2D S02 and Microscan MS 2D scan engine are intended for connection to a UL listed direct plug in power unit marked Class II and rated 5 VDC at 5 Watts or greater if using additional I O and or electrical accessories Microscan and ESP are Regi
16. ress the following screen will appear Follow the prompts to assign your desired parameters into the module If no Lantronix modules were detected upon the startup search you will need to first enter the MAC address printed on the module or product label Device Identification Enter the hardware address of the device This is typically printed on the back panel of the device in the Form 12 34 56 78 94 BC m Would you like to specify the IP address or should the unit getits settings from a server out on the network Obtain an IP address automaticaly Assign a specific IP address TCP P Tutorial Back Cancel Help Please fillin the IP address subnet and gateway to assign the device The subnet will be filled in automatically as you type but please verify it for accuracy Incorrect values in any of the below fields can make it impossible for your device to communicate and can cause network disruption IP address 192 168 56 90 Subnet mask 255 255 255 0 Defaut gateway 0 0 0 0 C lt set net gt 7 _concet_ mb You may encounter this message depending on your local conditions It is OK to proceed gt The address you entered is not on the same subnet as this PC C s IP address 192 168 1 101 PC s subnet 255 255 255 0 Would you like to continue and set the IP Address DTC 2D E02 Ethernet Interface User s Manual 7 Running the Lantronix Devicelnsta
17. stered Trademarks of Microscan Corp www Microscan com About this manual The DTC 2D E02 interface is an Ethernet communications accessory for Microscan s new state of the art OEM MS 2D Scan Engine and allows standard EIA RS 232 communications with the OEM engine unit It is designed as a low profile daughter card that would normally mount directly on top of the MS 2D scanner The DTC 2D E02 RS 232 Ethernet interface permits the Microscan MS 2D OEM scan engine to be used in designs where the OEM VAR or end user simply wants to use the MS 2D engine design without a costly design integration into custom discrete circuitry The DTC 2D E02 is a CMOS TTL RS 232 to Standard Ethernet interface converter for the MS 2D engine All other I O and control signals are passed through directly This manual provides information on connecting the DTC 2D E02 Ethernet interface card to the Microscan MS 2D scan engine For scanner operations please refer to the Microscan MS 2D Scan Engine User s Manual P N 84 000008 Rev A or the Microscan website www Microscan com DTC 2D E02 Ethernet Interface User s Manual O Table of Contents Getting Started Attaching the DTC 2D E02 interface card to the MS 2D scan engine Attaching the DTC 2D E02 interface to your host system Host Communications Lantronix Device Installer Installation Running the Device Installer Program Assign an IP address Wizard Web configuration o Network Settings o S
Download Pdf Manuals
Related Search