user manual s series web
Contents
1. from the plant material and turning the union nuts to the right will bring the wires closer to the plant material to be trimmed Place the grill onto the lower base motor support ensuring that it is level and start the rheostat on high Use the tool to adjust the desired height we suggest 5 32 in By placing the block on the grill and adjusting one nut at a time to the desired height j N Waku Sema sa ku sed ks 4 union nuts union nut Maintenance To receive maximum performance from the Thunder Vak it is important that the maintenance schedule be followed Always stop the motor and unplug the unit before any maintenance repairs or cleaning Cleaning the machine after each use will ensure the ThunderVak longevity To clean it we suggest using Bio Green Clean or other natural cleaner Simply follow the instructions on the bottle for the dilution rate spray down the machine let it sit for a few minutes and wipe clean with a damp cloth Never use an abrasive pad on any component of this machine as it will scratch the surface Make sure that all 8 cutting wires are in good condition before operating the machine Each machine comes with replacement cutting wires If one needs replacement simply slide it out discard and replace with a new one US and Canadian patents pending Page 14 www ThunderVak com User Manual Warranty ThunderVak warranty obligations are limited to the terms set forth belo2. to toggle work table with the 2 bolts and nuts provided 10 Making sure the support is level insert the catch all bag folding the corners over the support 11 Place the work table over the support 12 Hook the capacitor and rheostat for the cutting motor onto the metal bracket that is on the side of the work table 13 Plug the power cord into an extension cord 15 amps minimum 14 Youare now ready to use your table top trimmer PT uode qoae en Notes gt The ThunderVak comes with the neoprene tumbler paddles installed A set of rubber ones have been included for your convenience If you would like to change them simply unscrew the paddles with a Phillips screwdriver gt The cutting wires are already installed but if you would like to change them simply slide them out and replace US and Canadian patents pending Page 8 www ThunderVak com Assembly cont d step 7 amp 8 step 9 2013 All rights reserved ThunderVak Registered Trademark of 105766 Canada Inc www ThunderVak com page 9 Assembly cont d step 12 Instructions Manual 1 3 Complete steps 1 through 14 SEE PAGE 8 Bolt the hand crank to the transparent top reservoir with the bolts included Slide the crosspiece with 4 tumbler paddles onto the shaft of the hand crank and tighten the small hex with the 1 8 Allen key supplied Place the reservoir on top of the lower base motor support making sur
3. S SERIES USER MANUAL FOR THE THUNDERVAK S SERIES TABLE MANUAL amp MOTORIZED Version 1 0 06 2013 2013 All rights reserved ThunderVak Registered Trademark of 105766 Canada Inc ThunderVak ThunderVak S Series Table S Series Mai 5 SERIES M ThunderVak nual S Series Motorized 2013 All rights reserved ThunderVak Registered Trademark of 105766 Canada Inc SO Lll ll Table of contents ll Page 5 6 EN Page 5 P ii i raffinato on Page 6 In Page 7 Electrical ie HS u L LLL Ya Page 7 AR Page 8 13 Neil Page 8 10 Sa VIA al Uo A Page 10 11 Series MOUOEIZOG Page 12 13 Page 13 14 ip 13 Tiano por NO Page 13 Adjusting the trimming help Page 13 14 Ali U L e A Page 14 YV L Page 15 US and Canadian patents pending Page 4 www ThunderVak com Parts Parts List eS eS Wik WN S Y Y Y Y Y pe de BL UI que le qoem Grill support Lower base Work table Transport rods Legs 2 Catch all bag Removable side chute manual amp motorized versions Capacitor and rheostat for the cutting motor Transparent top reservoir with feeder manual motorized versions Upper motor with speed control motorized version Cr
4. ange them simply slide them out and replace Use Important test the trimmer with a small amount of plant material first to ensure your satisfaction Start the upper motor by putting the button to RUN to engage the rubber or neoprene tumbler paddles Turn the rheostat to the desired speed between 0 and 60 rpms Now start the lower motor VAR and adjust the cutting speed with the rheostat You can also use your ThunderVak as a table top trimmer by simply removing the upper reservoir and disconnecting the upper motor electrical cord Preparation We recommend removing the stems before placing the plant material in the machine You do not have to remove the larger leaves for this machine as the trimming is more precise and efficient than other models on the market Transportation Always turn the motors off and unplug the machine before moving it When transporting it always secure it to prevent damages Adjusting the trimming height Note the height has already been factory preset and should not require any adjustment 2013 All rights reserved ThunderVak Registered Trademark of 105766 Canada Inc www ThunderVak com page 13 Use cont d Block to adjust the trimming height This tool is used to adjust the cutting height 4 union nuts on the lower base motor support allow adjustment of the trimming height and are pre set by the manufacturer Turning left will distance the wires
5. e to allign the holes on the support witht he brackets on the reservoir SEE RED CIRCLES Attach the removable side chute to the transparent top reservoir You are now ready to use your manual trimmer US and Canadian patents pending Page 10 www ThunderVak com 2o Assembly cont d step 3 step 4 step 5 2013 All rights reserved ThunderVak Registered Trademark of 105766 Canada Inc www ThunderVak com page 11 ZA 1 1 Assembly cont d Instructions Motorized l Complete steps 1 through 14 SEE PAGE 8 2 Connect upper motor with speed control to the transparent top reservoir with the 4 bolts attached to the motor 3 Slidethe crosspiece with 4 tumbler paddles onto the shaft of the hand crank and tighten the small hex with the 1 8 Allen key supplied 4 Place the reservoir on top of the lower base motor support making sure to allign the holes on the support with the brackets on the reservoir SEE RED CIRCLES 5 Attach the removable side chute to the transparent top reservoir US and Canadian patents pending Page 12 www ThunderVak com Assembly cont d Notes gt The ThunderVak comes with the neoprene tumbler paddles installed A set of rubber ones have been included for your convenience If you would like to change them simply unscrew the paddles with a Phillips screwdriver gt The cutting wires are already installed but if you would like to ch
6. osspiece with 4 tumbler paddles Aluminium grill manual amp motorized versions Handle to toggle work table Hand crank manual version a tool set consisting of one 1 8 Allen key one 3 8 Allen key hex nut driver block to adjust trimming height cutting wires 1 grill support 2 lower base 3 work table 2013 All rights reserved ThunderVak Registered Trademark of 105766 Canada Inc www ThunderVak com page S Parts diagrams 5 legs 6 catch all bag 10 upper motor 11 crosspiece amp paddles 13 handle 14 hand crank 15 tool set US and Canadian patents pending Page 6 www ThunderVak com Safety warnings This is a high speed power tool and should be taken seriously Careless or improper use may cause serious or even fatal injury Warning IMPORTANT e Make sure to inspect the machine before each use e Always wear safety glasses gloves ear plugs and proper protective clothing Do not apply pressure to the grill Do not use any instruments or tools above the machine e Keep work area clean and clear of debris e Always disconnect the power before servicing the machine e Never move tilt or rotate machine while in use e Never allow the machine to run unattended e Minors should never be allowed to operate this machine his machine is to be used with all existing laws and regulations Ihe manufacturer and distributor does not accept any liability or respon
7. sibility for misuse of the product or for damages caused to or by the ThunderVak resulting from improper use or assembly Read the entire users manual prior to operating the ThunderVak Read all warnings before operating Electrical Requirements Wiring requirements 110V 15amps The ThunderVak is equipped with a power supply cord having a grounded 3 prong plug To minimize possible Electrical shock hazard the cord must be plugged into a mating grounded 3 prong outlet grounded in accordance with all Shock local codes and ordinances Hazard 2013 All rights reserved ThunderVak Registered Trademark of 105766 Canada Inc www ThunderVak com page ASTRA Assembly To receive maximum performance and satisfaction from the Thunder Vak it is important that you read and understand the safety warnings before using this machine Instructions Table Top Open the box and cut the straps that are holding the machine in place Take everything out of the box Remove the grill support from the legs and put aside Next remove the work table from the legs and undo the screws that are on each leg Unbolt the transport rods from the frame Keep these pieces for future transportation Bolt the 2 legs onto the grill support 7 Place the legs and support into the lower base making sure that they are pushed in to the bottom 8 Tighten the smalls screws at the bottom of the legs 9 On the side of the support bolt the handle
8. tHydro com US and Canadian patents pending 2013 All rights reserved ThunderVak Registered Trademark of 105766 Canada Inc
9. w ThunderVak 105766 Canada Inc warrants this hardware product against defects in materials and workmanship for a period of ONE 1 YEAR from the date of original retail purchase excluding all replacement rubber parts and cutting wires If a defect exists at its option ThunderVak will 1 repair the product at no charge using new or refurbished replacement parts or 2 exchange the product with a product that is new or which has been manufactured from new or serviceable used parts and is at least functionally equivalent to the original product If usage of this ThunderVak product violates the guidelines of this limited warranty IhunderVak will repair the product and charge the purchaser for the cost of company time materials and shipping costs ThunderVak shall not be liable for any loss injury or damages to persons or property resulting from the use of this product or any failure of or defect in this product nor shall hunderVak be liable to the initial user of this product or to any other person or entity for any general special direct indirect incidental consequential exemplary punitive or OTHER DAMAGES of any kind or nature whatsoever 2013 All rights reserved ThunderVak Registered Trademark of 105766 Canada Inc www ThunderVak com page 15 Mega Watt HydroCulture Distributed by 105766 Canada Inc MegaWatt HydroCulture 636 Route 364 Morin Heights PQ JOR 1H0 Canada 1 800 575 2515 www MegaWat
Download Pdf Manuals
Related Search