Or the User Manual
Contents
1. CONTENTS Section Page No 1 00 Introduction 2 1 01 Features 3 1 02 Technical Specifications 3 1 03 Installation 4 2 00 Easy Programming with Profiles 5 2 01 Setup as GSM Baby Phone 5 2 02 Setup as GSM Panic Button 7 2 03 Setup as Monitoring and Listening Device 9 3 00 User Commands 10 3 01 Command Check System State 11 3 02 Command Arm System 11 3 03 Command Disarm System 11 3 04 Command Change User Code 12 3 05 Command Change Phone Number 12 3 06 Command Delete Phone Number 12 3 07 Command Request Phone Number 13 3 08 Command Set Call Mode 13 3 09 Command Set Dial Attempts 14 3 10 Command Set Language 14 3 11 Command Set Call In Mode 14 3 12 Command Set Microphone Volume 15 3 13 Command Activate Deactivate Microphone 15 3 14 Command Activate Deactivate Panic Button 16 3 15 Command Set Alarm Message 17 3 16 Command Set Microphone Re trigger Time 17 3 17 Command Set Panic Button Re trigger Time 18 3 18 Command Set Profile 18 4 00 Factory Reset and Default Settings 19 5 00 Type Label 20 GSM Baby Phone User Manual Rev 29 01 2013 1 www dsp technology com 1 00 Introduction The GSM Baby Phone combines a variety of functions for the following applications like The Baby Phone to alert parents that their babies or small children are awake END The Panic Button to alert family members if older people or children are2. and listen to the room in which the product is installed However the interested or advanced user can refer to Chapter 3 User Commands to get an overview of all commands and capabilities 3 00 User Commands The GSM Baby Phone is configured and checked by sending SMS to it Following features can be modified or accessed Arming and Disarming the System and request of current System State Changing 4 Digit User Code Eight Phone Numbers and one Service Phone Number Phone Number Modes Call SMS or both Two Alarm and Service Message Texts Reply Language currently English or German Quantity of Dial Attempts Setting of Profiles Setting of Call In Mode Setting of Re trigger Times Microphone and Panic Button Activate Deactivate Microphone or Panic Button Set Microphone Volume GSM Baby Phone User Manual Rev 29 01 2013 10 www dsp technology com 3 01 Command Check System State The user can check the current state of the GSM Baby Phone by sending the following command by SMS Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 SYSTEM ARMED SYSTEM DISARMED 3 02 Command Arm System The user can arm the GSM Baby Phone by sending the following command by SMS Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 SYSTEM ARMED ON Arming will result in a steady blue backlight of the Sleep Button Now Voice Triggering via the Microphone is active Note T
3. be used to disable any re trigger until the system was disarmed and armed again 3 18 Command Set Profile The product offers the user a shortcut for programming Profiles Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 PROFILE CHANGED PROFILE BABY 1111 PROFILE CHANGED PROFILE PANIC 1111 PROFILE CHANGED PROFILE LISTEN The following parameters are modified while setting a profile Call In Mode e Voice Activation Call In Mode Voice Activa Panic Activa Panic Activation tion tion ais A a ALWAYS ON Level 5 The list gives an overview about the automated settings PANIC 5 minutes OFF for each of the five profiles LISTEN ALWAYS OFF GSM Baby Phone User Manual Rev 29 01 2013 18 www dsp technology com 4 00 Factory Reset and Default Settings After shipment the product arrives with all the settings in a default state called the Factory De fault Any time the user is able to generate this state by shorting the two Factory Reset Pins while the product is powered up The product will give several Shorting the two pins will reset the system to the wv factory default state oles The following table gives an overview of all Factory Default Settings Setting Factory Default Setting Notes New Setting Microphone Re trigger Time RETRIGGER1 Panic Button Re trigger Time RETRIGGER2 Message 1 Message 2 Phone Number 1 Phone Number 2 Phone Number 3 Phone Nu
4. engaged disarmed and can t accept voice triggering If the blue backlight of the Sleep Button is steady on then the system is engaged armed and may accept triggering via the Microphone The Panic Button provides a red backlight If this red backlight is steady on then the Panic Button is ready to use Pressing the button will send a message or make a call to all the pre programmed phone numbers up to 8 After a period of time the so called Re trigger Time the Panic button will be illuminate red again indication that it is ready again to trigger a call or a message GSM Baby Phone User Manual Rev 29 01 2013 7 www dsp technology com To setup the product as a Panic Button please follow the steps as described Open the back housing and insert a SIM card with no PIN assigned Connect the plug of the external Wall Plug Power Supply to the DC Jack on the right side of the device Insert the Wall Plug into the Mains outlet The Panic Button will give several short acknowledgment beeps and the blue LED of the Sleep Button should be flashing fast to indicate it is looking for the GSM network Wait until the blue LED is steady on or flashing slowly Now the units is ready to receive and process messages as described underneath Note Using the product as a Panic Button requires the setting of certain variables To simplify the programming the PANIC Profile may be used However all parameters can also be programmed ste
5. 3 16 www dsp technology com 3 15 Command Set Alarm Message The product provides two different Alarm Messages These messages can be modified to any text with up to 63 characters The two Alarm Messages are in their default stage set as following e Message 1 ALARM o Message 2 PANIC ALARM Message 1 is always assigned to the Voice Trigger Event from the microphone Message 2 is always assigned to the Panic Button Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 ALARM MESSAGE SMS1 PLEASE HELP CHANGED This command would set the Message 1 used for any Voice Trigger event to the new contents PLEASE HELP Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 ALARM MESSAGE SMS1 EMERGENCY CHANGED This command would set the Message 2 used when the Panic Button is activated to the new contents EMERGENCY 3 16 Command Set Microphone Re irigger Time After a Alarm Event the room noise level might be still elevated and a immediate re trigger of the Alarm Event might occur if the system was not disarmed The Re trigger Timing allows the user to set a period of time in which the system will not generate any Alarm messages or calls Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 MICROPHONE RE RETRIGGER1 5 TRIGGER TIME CHANGED This command would set the Re trigger Time of the Microphone to 5 minutes Within the 5 min utes of any Alarm event t
6. CALL MODE CHANGED CALL MODE CHANGED www dsp technology com Message to Baby Phone Reply from Baby Phone 1111 This command can modify the ALARM MESSAGE SMS1 PLEASE COME alarm message which would ll CHANGED HOME CHILD AWAKE be sent in the event of a cry i ing noisy child 4111 This command changes the USER CODE CHANGED PIN 1234 user code From now on the new user code must be used instead of 1111 These commands are already sufficient to setup the product as a Baby Phone However the interested or advanced user can refer to Chapter 3 User Commands to get an overview of all commands and capabilities 2 02 Setup as GSM Panic Button The product may be used as a GSM Panic Button This function allows the user to press the Panic Button for a period of time to call for help in case of an emergency It may be used by elderly disabled or sick people but also by small children alone at home Furthermore the Panic Button could be used by store clerks to call for help in case of an armed robbery In the Panic Button Mode the user will use the Panic Button The Sleep Button may be used for additional functionality if programmed The Sleep Button includes a blue backlight which indicates the mode of operation If the blue backlight of the Sleep Button is flashing fast then the system tries to connect to the GSM network If the blue backlight of the Sleep Button is flashing slowly then the system is not
7. by Phone Possible Replies from GSM Baby Phone 1111 PHONE NUMBER PHONE1 CHANGED This command would delete Phone Number 1 1111 ALL NUMBERS DELETED DELETE ALL This command would delete all eight Phone Numbers Deleted Phone Numbers will not be used while dialing and sending Alarm Messages GSM Baby Phone User Manual Rev 29 01 2013 12 www dsp technology com 3 07 Command Request Phone Numbers The user can check all eight phone numbers by issuing the following command Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 13802666005 PHONE1 The command requests Phone Number 1 and the device returns the programmed value If no number is assigned it will return the text EMPTY Instead of command PHONE1 the commands PHONE2 PHONES can be used to request the corresponding phone numbers Note that all phone numbers are cleared in the Factory Default state 3 08 Command Set Call Mode Each Phone Number can be used to send a SMS and or make a call in case of an Alarm event Therefore the user may define this functionality as following Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 CALL MODE CHANGED CALL1 SMS This command would set Phone Number 1 to send a Alarm Message 1111 CALL MODE CHANGED CALL1 CALL This command would set Phone Number 1 to make a call in case of an Alarm 1111 CALL MODE CHANGED CALL1 BOTH This command would set Phone Number 1 to sen
8. c Alarm 1111 This command changes the USER CODE CHANGED PIN 1234 user code From now on the new user code must be used instead of 1111 ALARM MESSAGE CHANGED These commands are already sufficient to setup the product as a GSM Panic Button However the interested or advanced user can refer to Chapter 3 User Commands to get an overview of all commands and capabilities 2 03 Setup as Monitoring and Listening Device The product may be used as a Listening Device for silently monitoring conversations CAUTION The user must observe the Privacy Laws of his country In this Mode the user will just use the Sleep Button The Panic Button may be used for additional functionality if programmed The Sleep Button includes a blue backlight which indicates the mode of operation If the blue backlight of the Sleep Button is flashing fast then the system tries to connect to the GSM network If the blue backlight of the Sleep Button is flashing slowly then the system is not engaged disarmed and can t accept triggering from the Inputs If the blue backlight of the Sleep Button is steady on then the system is engaged armed and accept triggering from the Inputs At least one of the two inputs should be set to an Entry Exit Zone This allows the user leav ing the premises without triggering an alarm and entering it and disarming the system without triggering an alarm as well Also the Panic Button includes a red backlight How
9. d a message and make a call in case of an Alarm If the Call Mode for Phone Number 2 needs to be changed then the CALL2 command shall be used Phone Number 3 corresponds to command CALL3 and so on until CALL8 GSM Baby Phone User Manual Rev 29 01 2013 13 www dsp technology com 3 09 Command Set Dial Attempts In case of an Alarm event the product will process all valid phone numbers starting from Phone Number 1 If the call mode of the current phone number is set to CALL or BOTH it will try to call it Ifthe call was not successful e g busy the product might attempt multiple times to call the par ticular phone number again The user can set any value from 1 to 4 as maximum dial attempt Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 DIAL ATTEMPTS ATTEMPTS 2 CHANGED 3 10 Command Set Language The product offers the user currently two different language packs used for the reply messages English and German Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 SPRACHE GEAENDERT LANG DE 1111 LANGUAGE CHANGED LANG ENG After changing the language all further reply mes sages will be in the newly set language Commands remain unchanged However some of the commands may have an alternative Ger man command word which are not further described in this English User Manual and are subject of the German User Manual 3 11 Command Set Call In Mode The user may need to cal
10. d process messages as described underneath Note Using the product as a Baby Phone requires the setting of certain variables To simplify the programming the BABY Profile may be used However all parameters can also be programmed step by step This may be suitable for the advanced user Message to Baby Phone 1111 PROFILE BABY 1111 PHONE1 13802666005 1111 CALL1 CALL 1111 CALL1 SMS 1111 CALL1 BOTH Sets a variety of parameters suitable to the Baby Phone Mode Sets the first phone number of the mobile phone which the Baby Phone should send mes sages to or call in an event of a crying noisy baby Using PHONE2 PHONE8 may set additional 7 phone numbers Sets the first phone number to Call Mode No message would be send but Phone Number 1 would be called in an event of a crying noisy baby Using CALL2 CALL8 may set this feature to the addi tional 7 phone numbers Would sets the first phone number to Message Mode Only a message would be sent to Phone Number 1 in an event of a crying noisy child The Baby Phone would not call Phone Number 1 Would sets the first phone number to Message Mode and Call Mode First a message would be sent to Phone Num ber 1 in an event of a crying noisy child Then the Baby Phone would call Phone Num ber 1 as well GSM Baby Phone User Manual Rev 29 01 2013 6 Reply from Baby Phone PROFILE CHANGED PHONE NUMBER CHANGED CALL MODE CHANGED
11. eep Button includes a blue backlight which indicates the mode of operation If the blue backlight of the Sleep Button is flashing fast then the system tries to connect to the GSM network If the blue backlight of the Sleep Button is flashing slowly then the system is not engaged disarmed and can t accept voice triggering If the blue backlight of the Sleep Button is steady on then the system is engaged armed and accept voice triggering The Panic Button provides a red backlight If this red backlight is steady on then the Panic Button is ready to use Pressing the button will send a message or make a call to all the pre programmed phone numbers up to 8 After a period of time the so called Re trigger Time the Panic button will be illuminate red again indication that it is ready again to trigger a call or a message GSM Baby Phone User Manual Rev 29 01 2013 5 www dsp technology com To setup the Baby Phone Mode please follow the steps as described Open the back housing and insert a SIM card with no PIN assigned Connect the plug of the external Wall Plug Power Supply to the DC Jack on the right side of the device Insert the Wall Plug into the Mains outlet The GSM Baby Phone will give several short acknowledgment beeps and the blue LED of the Sleep Button should be flashing fast to indicate it is looking for the GSM network Wait until the blue LED is steady on or flashing slowly Now the units is ready to receive an
12. ever the red backlight is usually off since the Panic Button is disabled To setup the product as a Listening Device please follow the steps as described Open the back housing and insert a SIM card with no PIN assigned Connect the plug of the external Wall Plug Power Supply to the DC Jack on the right side of the device Insert the Wall Plug into the Mains outlet GSM Baby Phone User Manual Rev 29 01 2013 9 www dsp technology com The Listening Device will give several short acknowledgment beeps and the blue LED of the Sleep Button should be flashing fast to indicate it is looking for the GSM network Wait until the blue LED is steady on or flashing slowly Now the units is ready to receive and process messages as described underneath Note Using the GSM Baby Phone as a Listening Device requires the setting of certain variables To simplify the programming the LISTEN Profile may be used However all parameters can also be programmed step by step This may be suitable for the advanced user Message to Listening Device 1111 Sets a variety of parameters PROFILE LISTEN suitable to the Listen Device 1111 Mode This command changes the PIN 1234 user code From now on the new user code must be used instead of 1111 Reply from Listening Device PROFILE CHANGED USER CODE CHANGED These few commands are already sufficient to setup the product as a Listening Device and the user can call in at any time
13. hand set Those SIM cards are not suit able for usage with the GSM Baby Phone GSM Baby Phone User Manual Rev 29 01 2013 4 www dsp technology com 2 00 Easy Programming with Profiles The GSM Baby Phone can be operated in different modes This requires programming of several different settings and variables To simplify the programming the GSM Baby Phone provides pro gramming of three profiles The Baby Phone Profile to use the product as a GSM Baby Phone Baby Monitor The Panic Button Profile to use the product as a GSM Panic Button o The Listen Profile to use the product as a Monitoring and Listening Device Programming of the GSM Baby Phone is always done in the following three steps Send SMS to your GSM Baby Phone Baby Phone s phone number depends on SIM card inserted containing your four digit user code factory default is 1111 and a command GSM Baby Phone will verify User Code and process command GSM Baby Phone will send an acknowledgement SMS back to the mobile phone which has sent the command 2 01 Setup as GSM Baby Phone The main mode of the GSM Baby Phone is the Baby Phone Mode Baby Monitor Mode This allows the parents to trigger a call or a message when a baby is crying or young children are awake while the parents are not at home or not in the same room Also the device allows the parents to call in and monitor the room at any time In the Baby Phone Mode the user may use both buttons Panic and Sleep The Sl
14. he Panic Button is excluded of the Arming Disarming procedure and is always active if programmed 3 03 Command Disarm System The user can disarm the GSM Baby Phone by sending the following command by SMS Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 SYSTEM DISARMED OFF Disarming will result in a slow flashing blue backlight of the Sleep Button Now Voice Triggering via the Microphone is disabled Note The Panic Button is excluded of the Arming Disarming procedure and is always active if programmed GSM Baby Phone User Manual Rev 29 01 2013 11 www dsp technology com 3 04 Command Change User Code The user should change the default User Code 1111 to any other User Code This User code may include the numbers 0 9 as well as the characters A Z Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 USER CODE CHANGED PIN 1234 3 05 Command Change Phone Number The user can program up to eight phone numbers PHONE1 PHONE2 One phone number can have up to 24 digits and include the numbers 0 9 and the symbol Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 PHONE NUMBER PHONE 1 13802666005 CHANGED After setting the Phone Number it will be used while dialing and sending Alarm Messages 3 06 Command Delete Phone Number The user can delete single Phone Numbers or even all Phone Numbers in one go Message to GSM Ba
15. he product to an initial state The internal SIM Card Holder allows the usage of standard 3V SIM cards One standard DC Jack Input allows to connect the external DC Power Supply The external wall plug power supply is included The product is CE compliant suitable for residential commercial and industrial use Note The SIM card is not included in the package It should be purchased by end user sepa rately 1 02 Technical Specifications Power Supply 9 16 Volts DC Current Drain Standby 20mA Peak Current Drain Dialing GSM Dialing 750mA GSM Part EGSM GPRS 900 1800MHz GSM Baby Phone User Manual Rev 29 01 2013 3 www dsp technology com 1 03 Installation Remove lid and remove two screws to be able to open back housing After removing the back housing proceed to insert the SM SIM card To operate the product a valid GSM SIM card must be inserted to the product The SIM card comes with its own phone number This number shall be used to program the device and to call it A Pre Paid SIM card is suitable for the product Monthly service charges may occur depends on the chosen u GSM service provider The SIM card slides into the SIM card holder as shown in the picture beside The SIM card holder provides a lock ing mechanism for the card Note that the PIN of the SIM card should be disabled before inserting it to the GSM Baby Phone Some SIM cards are 3G only or locked to a specific
16. igger an alarm call or message The user can activate or de activate this function and furthermore define the trigger level Message to GSM Baby Phone Possible Replies from GSM Baby Phone aaa MICROPHONE MIC ON ACTIVATED GSM Baby Phone User Manual Rev 29 01 2013 15 www dsp technology com Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 MICROPHONE MIC OFF DEACTIVATED MICROPHONE DEACTIVATED MICROPHONE ACTIVATED The last command would activate the microphone with a very insensitive trigger level Instead of 1 the user could state a value from 2 9 highest sensitivity The ON command also sets the trigger level to 5 medium level 3 14 Command Activate Deactivate Panic Button The product includes a Panic Button After pressing it for a certain time it may trigger a Alarm event The user can set this timing or even deactivate it completely Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 PANIC BUTTON PANIC ON ACTIVATED This command will enable the Panic Button with a triggering time of 500ms PANIC BUTTON ACTIVATED This command will enable the Panic Button with a triggering time of 1s Instead of 1 the user could state a value of 2 9 which correspond to 2s 9s triggering time 1111 PANIC BUTTON PANIC OFF DEACTIVATED This command will disable the Panic Button Instead of OFF the user could use NEVER GSM Baby Phone User Manual Rev 29 01 201
17. in need of urgent help or if store keepers need assistance in the case of an armed robbery The Monitoring Listening Device to silently monitor staff or family members Please comply with your local privacy laws GSM Baby Phone Profile Baby This function allows parents to monitor their children The internal microphone checks the ambient noise level If the baby cries and the noise threshold is reached then the GSM Baby Phone will send a message or and call up to 8 pre programmed phone numbers Parents may call in at any time and check whether the child is sleeping GSM Panic Button Profile Panic This function allows old people or small children to call for help in case of an emergency This function also allows store clerks to call for help in case of a robbery installation under the desk The Panic button will trigger Alarm Message or and call up to 8 pre programmed phone numbers Work Place Family Monitoring Listening Device Profile Listen e The device may be used to silently monitor the conversations or the activities of staff or fam ily members e This could be archived by silently calling into the device Disclaimer We DSP Technology HK Ltd do not encourage the usage of Profile Listen since it may violate the privacy laws of the country in use DSP Technology HK Ltd does not accept any liability claims for the usage or the results of the usage of the GSM Baby Phone The usage
18. l into the GSM Baby Phone to monitor the room However it may be not desirable to let anybody call in and therefore it may be useful to limit the Call In functionality Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 CALL IN MODE CHANGED CALLIN 0 This command disables the Call In feature Any incoming call is rejected by the GSM Baby Phone Instead of O the user could use NEVER as well GSM Baby Phone User Manual Rev 29 01 2013 14 www dsp technology com Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 CALL IN MODE CHANGED CALLIN 1 This command allows to accept incoming calls for up to one minute after the last reception of a valid User code After this time any incoming call is rejected Instead of 1 the user could state a number of up to 999 which would correspond to 999 minutes After 999 minutes no incoming call would be accepted 1111 CALL IN MODE CHANGED CALLIN ALWAYS This command allows the acceptance of incoming calls at any time 3 12 Command Set Microphone Volume The internal microphone allows the user to listen to the room With the following command the user can adjust the volume Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 VOLUME CHANGED VOLUME 1 A value of 1 corresponds to the lowest volume A value of 8 corresponds to the highest volume 3 13 Command Activate Deactivate Microphone The internal microphone allows to tr
19. mber 4 Phone Number 5 Phone Number 6 5 minutes ALWAYS ALARM PANIC ALARM empty empty empty empty empty empty GSM Baby Phone User Manual Rev 29 01 2013 19 www dsp technology com Option Factory Default Setting Notes New Setting Phone Number 7 empty Phone Number 8 empty Voice Activation ON Level 5 Panic Button Activation 1s 5 00 Type Label GSM Baby Phone Part No DS 032 www dsp technology com Designed in Germany Made in China O 799493 915105 Design and Specification may be subject to changes without prior notice GSM Baby Phone User Manual Rev 29 01 2013 20 www dsp technology com
20. of this product is on the user s own risk There are no user serviceable parts contained within this unit DO NOT attempt to interfere with or alter any of the electronic components To do so may damage the electronic circuitry and will invalidate you warranty Every effort has been made to provide accurate information however slight variations can occur We reserve the right to make changes for the product improvement at anytime GSM Baby Phone User Manual Rev 29 01 2013 2 www dsp technology com 1 01 Features A four digit User Code protects the functioning of the product und the settings Up to 8 programmable phone numbers Each phone number accepts up to 24 digits IP dialing possible Each number can be programmed to send an Alarm SMS just call or send a SMS and call The GSM Baby Phone is fully programmable by SMS There are up to two different Alarm Messages programmable The internal Microphone allows alarm triggering as well listening to the premises The System allows programming of trigger and volume level The System provides two Buttons with LED backlight e Sleep To enable and disable the selected function e Panic To generate a fast emergency call or an emergency message The System accepts signals from two trigger Sources e Microphone e Panic Button Different User Profiles allow a simple way of programming of the device also for the inexpe rienced user An Internal Factory Reset Jumper allows the user to reset t
21. p by step This may be suitable for the advanced user Message to Panic Button 1111 PROFILE PANIC 1111 PHONE 1 13802666005 1111 CALL1 CALL 1111 CALL1 SMS 1111 CALL1 BOTH Sets a variety of parameters suitable to the Panic Mode Sets the first phone number of the mobile phone which the Panic Button should send messages to or call in an event of a crying noisy baby Using PHONE2 PHONE8 may set additional 7 phone numbers Sets the first phone number to Call Mode No message would be send but Phone Number 1 would be called in an event of a pressed Panic Button Using CALL2 CALL8 may set this feature to the addi tional 7 phone numbers Would sets the first phone number to Message Mode Only a message would be sent to Phone Number 1 in an event of a pressed Panic But ton The Panic Button Phone would not call Phone Number 1 Would sets the first phone number to Message Mode and Call Mode First a message would be sent to Phone Num ber 1 in an event of a pressed Panic Button Then the Panic Button would call Phone Num ber 1 as well GSM Baby Phone User Manual Rev 29 01 2013 8 Reply from Panic Button PROFILE CHANGED PHONE NUMBER CHANGED CALL MODE CHANGED CALL MODE CHANGED CALL MODE CHANGED www dsp technology com Message to Panic Button Reply from Panic Button 4111 This command can modify the alarm message which would be sent inthe event of a Pani
22. riggered by the Microphone no new Microphone Trigger would be al lowed Valid values range from 0 999 E g 999 means that a new trigger could only be generated 999 minutes after the last Microphone Alarm event 0 or ALWAYS may be used to allow an immediate re trigger NEVER could be used to disable any re trigger until the system was disarmed and armed again GSM Baby Phone User Manual Rev 29 01 2013 17 www dsp technology com 3 17 Command Set Panic Button Re trigger Time After a Panic Alarm the user in panic might try to trigger the Panic Button again and again but help would be already on the way Multiple calls and messages may be generated Therefore it might be useful to prevent an immediate re trigger of the Panic Alarm The Re trigger Timing al lows the user to set a period of time in which the system will not generate any Alarm messages or calls Message to GSM Baby Phone Possible Replies from GSM Baby Phone 1111 PANIC BUTTON RE RETRIGGER2 1 TRIGGER TIME CHANGED This command would set the Re trigger Time of the Panic Button to 1 minute Within one minute after any Panic Alarm no new Panic Button activations would be accepted The red backlight of the Panic button is turned off within this time Valid values range from 0 999 E g 999 means that a new Panic trigger could only be gener ated 999 minutes after the last Panic Alarm event 0 or ALWAYS may be used to allow an immediate re trigger NEVER could
Download Pdf Manuals
Related Search