User Manual
Contents
1. Y button and the collar receiver will flash signifying the LED LIGHT function works Figure 2 3 Figure 2 4 NB 1 The screen of the remote transmitter does not display when 1 Itisin STANDBY mode To save power the transmitter will go into STANDBY mode if there is no operation for 2 minutes You can press any button except for the LED LIGHT button to activate it and then its screen will show the display 2 Itisin DEEP SLEEP mode To save power the transmitter will go into the DEEP SLEEP mode if there is no operation for 5 minutes You can hold and press the MODE button for 1 second to activate it and then its screen will display 2 The collar receiver will go into DEEP SLEEP mode if there is no operation for 5 minutes Any movement will activate it If the receiver has no response then you press the Y button and if its indicator light is not on either then you can shake it or let your dog move to 11 activate it If you shake the receiver you ll hear a rattling noise caused by the built in vibration sensor which indicates that it is in working status Step 5 Fit the collar receiver Important The proper fit and placement of the collar receiver is essential for effective training The metal contact probes must have direct contact with your dog s skin as follows 1 To fit the collar receiver you will need to attach the collar strap to the receiver box 3A 2 With your dog standing in front of you place the c2. DTC 280 Pet Trainer Dog Training Collar Manual pet Ziner Waterproof and Re chargeable Important Safety Information WARNING NOT FOR AGGRESSIVE DOGS Do not use this product if your dog is aggressive or if your dog is prone to aggressive behavior Aggressive dogs can cause severe injury and even death to their owner and others If you are unsure whether this product is appropriate for your dog please consult your veterinarian or certified trainer CAUTION Risk of skin damage Please read and follow the instructions carefully in this guide Proper fit of the collars is important because a loose collar may cause inconsistent performance A collar worn for too long or made too tight on the dog s neck may cause skin damage ranging from redness to pressure ulcers commonly known as bedsores Avoid leaving the collar on the dog for more than 12 hours per day When possible reposition the collar on the dog s neck every 1 to 2 hours Check the fit to prevent excessive pressure It is okay to trim any excess strap length Never connect a lead to the electronic collar because it may cause excessive pressure on the contacts Wash the dog s neck area and contacts of the collar weekly with a damp cloth Examine the contact area daily for signs of a rash or a sore If a rash or sore is found discontinue use of the collar until the skin has healed If the condition persists beyond 48 hours see your veterinarian Thes
3. confuse or frustrate the animal PLEASE NOTE Please note that when shaking the receiver you may hear a rattling noise which is actually caused by the built in vibration sensor and is by no means an indication of any malfunction in the receiver The range of up to 280m is line of sight and denotes the maximum valid distance that can be achieved in ideal conditions Any obstacles will reduce the effective distance Warranty Terms amp Conditions and Compliance MGG warrants to the original retail purchaser that your MGG DTC 280 Remote Training System will be free from defects in material and workmanship for a period of one year from the date of the original retail purchase provided that the damage is not caused by abnormal use or neglect Warranty does not cover lost parts cracked screen physical damage or water damage Warranty may include repair or exchange After the expiration of the warranty replacements and repairs are available for an additional charge Terms of Use It is understood that you accept without modification of the terms and conditions the offering to you of this product This training collar has been designed for the training of dogs Your dog s temperament may not be suitable for this system This collar is not recommended for dogs that are aggressive or have been neglected This product is designed for dog training purposes It is not intended to punish injure provoke or harm Using this product in a way in
4. The red LED light in the collar receiver will turn on A When the collar receiver has been fully charged the red LED light will turn off automatically B When charging is finished put the rubber cover securely back in place to keep the internal unit free from dust and water N B Charge the transmitter at least 6 hours for the very first charge even though it may indicate it is fully charged This conditions the battery Other than the first charge please just charge until the red light goes off NB The collar receiver will beep for 20 seconds if it needs recharging Step3 Synchronize the transmitter with collar receiver 1 Turn on the remote transmitter by pressing any button on the transmitter 2 Select channel 1 or 2 3 Press ON OFF button on the collar receiver to turn it on 4 Press ON OFF button again and hold it for 5 seconds and then the LED light will start to flash 5 Now you can hear the first beep from the collar receiver and then press the Y button of the transmitter immediately If too slow you may need to repeat the procedure but more quickly 6 You will hear the second beep from the receiver which signifies that the transmitter and the receiver have been synced 7 To sync the transmitter and the second receiver repeat step 2 through 6 8 Please be sure to choose the other channel NB According to the factory default settings when the collar receiver has been turned on the syncing should be complet
5. then contact a professional dog trainer in your vicinity Will I get exactly 280m of range with the dogtrainer rechargeable training collar 13 The range you get with this system will vary according to terrain vegetation as well as transmission from other radio devices To get the maximum amount of range please refer to the how the system works section of this guide What do I do if my dog s neck becomes red and irritated Discontinue use of the collar until the skin has healed If the condition persists beyond 48 hours see your veterinarian Can I replace the collar receiver with another kind of collar No Can I attach a leash to the collar receiver No This can result in pulling the metal probes too tightly against your dog s neck Attach a leash to a separate nonmetallic collar or a harness ensuring the extra collar does not put pressure on the metal probes How will I know when to charge the system For the remote transmitter the symbol will show up on the LCD screen For the receiver if you hear the beep from it for 20 seconds when it is already on you will need to have it charged What is the life span of the lithium batteries of the remote transmitter and the collar receiver They can be charged over 400 times How long can I leave collar receiver on my dog As the collar is not designed to be worn constantly we recommend the collar not be worn for more than 12 hours out of every 24 hour period How shou
6. e steps will help your dog stay safe and comfortable Millions of dogs are comfortable while wearing stainless steel contacts Some dogs are sensitive to contact pressure You may find after some time that your dog is very tolerant of the collar If so you may relax some of these precautions It is important to continue daily checks of the contact area If redness or sores are detected discontinue use until the skin has fully healed Thank you for choosing the MGG Dogtrainer brand You and your dog deserve a companionship that includes memorable moments and a shared understanding together Our mission is to ensure your dog s safety by providing you the tools and techniques to successfully train your dog Should you have any queries please contact our customer service info mggproducts co nz 09 401 6360 NOTE Please charge before using the product Components PET916 1 1 for 1 r receiver ee transmitter S g USB cable adjustable TPU belt two sets of Contact Points PET916 2 1 for 2 er receiver remote transmitter MTT see el cable adjustable i belt two sets a Contact Points Key Definitions M channel1 E channel 2 antenna tow battery indicator 1 100 level 4 static shock mode ran vibration mode m deep mode up down button F tight mode LED indic tor launch button mode button charging hole 1 Antenna Transmit signal to the collar receiver 2 LED Indicator It
7. ed within 10 seconds You have to press the Y button at least within 10 seconds Please DO NOT try to sync the transmitter with the two collar receivers at the same time Step 4 Test the training system The following testing methods will help you ascertain whether this training system is functioning correctly Please make sure that you have synchronized the transmitter and collar receiver before testing Figure 2 1 Figure 2 2 Test the static shock function Figure 2 1 Put the test light on the contact points of the collar receiver Turn on the remote transmitter switch to SHOCK mode and press the UP DOWN button to adjust the intensity level Press Y button and the bulb will flash signifying that the SHOCK function works Please 10 make sure the SHOCK level is well above 0 when testing the function Test the vibration functions Figure 2 2 Turn on the remote transmitter switch to VIBRATION mode and press the UP DOWN button to adjust the vibration level Press Y button and the collar receiver will vibrate signifying the VIBRATION function works Please make sure the vibration level is well above 0 when testing the function Test the beep function Figure 2 3 Turn on the remote transmitter switch to BEEP mode Press Y button and the collar receiver will beep signifying the BEEP function works Test the LED light function Figure 2 4 Turn on the remote transmitter switch to LED LIGHT mode Press
8. eriods can cause a condition similar to bedsores known as Pressure Necrosis To reduce the possibility you must do the following Never leave the collar on your dog for more than 12 hours per day Examine your dog s neck daily for any signs of a rash or a sore Supervise your dog during the first 2 days of training Regularly check the fit of the collar to prevent excessive pressure You should be able to insert one finger between the collar strap and your dog s skin SAFETY To maximise the effectiveness of the DTC 280 remote training system and the safety of your dog please check the fit of the collar frequently and re adjust the position of the electrodes on their neck if necessary checking for signs of irritation or discomfort If signs of skin irritation are noticed immediately discontinue use and apply antibiotic ointment to help heal and sooth the area If the condition persists beyond 48 hours seek the advice of a veterinarian Such side effects are extremely rare and are generally caused by a more serious underlying condition Wash the dog s neck area and the correction poles as often as needed to keep the area and poles clean Make sure the straps are clean for best performance The straps can be removed for cleaning but must be replaced in the same position 16 Stop any undesirable behaviour by administering the stimulus DURING THE ACTUAL BEHAVIOUR Using this device as a punishment after the fact does no good at all and will
9. ging Collar receiver b Metal Probes attach here They deliver vibration and static stimuli 2 ON OFF Encode Button Turn on off the collar receiver hold 5 seconds to encode the receiver gt Rubber Cover After completion of charging please put the cover securely in place to safeguard the internal unit from dust and water Charging Hole for collar receiver charging When charging the LED light is red when fully charged it turns to green Under light mode press the launch mode and the LED light in the collar receiver will flash green every one sec In standby status the LED light in the collar receiver will flash green every four seconds After turning on the receiver press and hold the ON OFF ENCODE button for five seconds to encode it Refer to the encoding synchronizing instructions on page 9 Features 1 Rechargeable remote transmitter and collar receiver The collar receiver and transmitter are both waterproof but we advise against submerging them under water for more than a few minutes LCD display with blue backlight screen for night use Four modes static vibration beep light at your disposal 100 intensity levels of vibrations 100 intensity levels of static shocks Intensity levels can be adjusted by pushing the UP DOWN button Power saving The collar receiver if left unused for 5 minutes will enter into SLEEP status and can be re activated by any movement T
10. he remote transmitter if left unused for 2 minutes will enter into STANDBY status If unused for 5 minutes it will enter into a DEEP SLEEP status To re activate the transmitter you can simply press any orange button The training system can be used with 1 or 2 collar receivers 9 CSB w How the dog training system works This system has been proven safe comfortable and effective for all dogs over 7Kgs except for aggressive dogs It assists you in controlling your dog without a leash within a range of 150 to 280m At the push of a button the remote transmitter sends a signal activating the collar receiver Using the remote trainer consistently and correctly most bad behavior that your dog exhibits can be corrected or any basic obedience commands taught It can also be used to deter such unwanted behaviors as jumping up digging and chasing While the stimulation is startling it is harmless to your dog Electronic training devices require 7 interaction and training from the owner to achieve the desired results Important The system has a range of up to 280m in ideal conditions Depending on the way you hold the remote transmitter the range may vary Hold the remote transmitter in a horizontal position away from your body to achieve optimum range Terrain weather vegetation transmission from other radio devices and other factors will affect the range of your remote transmitter Operating Guide Step 1 Prepare the remote tran
11. ity to learn basic commands A good indication will be if he she can understand and obey sit and stay commands That shows that the brain is sufficiently developed to understand the training collar logic Work with your dog on one behaviour at a time to avoid confusion and frustration 15 Use as little stimulus as possible and only to reinforce verbal commands when necessary Do not over correct your dog Use verbal commands first and supplement with a corrective stimulus only as needed Be consistent with your verbal commands using the same words every time Use the beeps as a warning by pushing the Beep button The dog will become conditioned to the beep preceding the corrective stimulus and will soon learn to recognise the beep as a warning along with your verbal command This system is not appropriate for correcting aggressive behaviour Please consult a professional trainer for advice about that Do not rely on this product solely to train your dog If your dog shows signs of growling snarling biting or aggression while using the collar stop training immediately and contact a professional trainer Although most dogs respond to this product some will not MGG cannot guarantee the effectiveness of this or any other trainer on your dog This product is not recommended for aggressive or elderly animals in poor health or animals otherwise unable to withstand the static stimulus Caution Any collar worn for extended p
12. ld I arrange training sessions for my dog Make the training sessions short and positive between 10 15 minutes long each time This will enable your dog to keep its attention focused on you What kind of dogs is the dogtrainer rechargeable training collar suitable for The collar is adjustable from length 15cm to 50cm If your dog s neck circumference is larger than 50cm this collar may not be suitable for your dog This collar is NOT suitable for dogs under 6Kgs Troubleshooting My dog is not responding after the dogtrainer dog training system has been installed successfully You need to charge the remote transmitter and the collar receiver for 6H separately before initial use 14 Check to see if the remote transmitter and the collar receiver have been turned on Check the intensity levels of vibration and static shock Make sure the collar receiver has sufficient power to operate Restart the collar receiver by pressing the ON OFF button Please test the 4 functions i e BEEP LIGHT VIBRATION AND STATIC SHOCK before initial use See the test the training system part of this guide for testing methods Check whether the collar receiver has entered into the DEEP SLEEP mode Check if the collar fits snugly with your dog s neck If necessary please trim your dog s neck hair so that the metal probes come in direct contact with your dog s skin If all of the above have been addressed your dog still gives
13. no response Please try to re synchronize the remote transmitter with the collar receiver The remote transmitter does not work Check if the remote transmitter is in low battery status If the icon shows up then battery exhaustion is imminent You have to press and hold the MODE button of the transmitter to turn it on Check if the transmitter has entered into the STANDBY or DEEP SLEEP status My collar receiver worked great for some time but now it does not work after charging Firstly check if the receiver has been charged correctly Check the prepare the collar receiver part of the guide for the correct charging method Check that the receiver has been turned on I want to test the collar receiver on myself but it does not work When testing the receiver on your hands please touch the 2 electrodes at the same time as touching one single electrode will not work General Training Tips The following are tips on how to get the best out of your MGG Dogtrainer Remote Dog Training Collar This product is intended to support behavioural training and is not designed to be used without the necessary interactions Always praise your dog for good behaviour Verbal commands combined with positive reinforcement will contribute to the success of your training and will achieve the desired results in the shortest time The recommended age for training is a minimum of 6 months provided that the dog has the attention span and capabil
14. ollar receiver around its neck so the receiver box and probes are on the underside of your dog s neck and making direct contact with the skin You may need to trim the fur to ensure good contact 3B 3 Fasten the collar strap The fit should be sung but not taut You should be able to place one finger beneath the collar strap around your dog s neck 3C 4 Allow your dog to wear the collar receiver for several minutes and then check the strap again As your dog becomes more familiar with the collar receiver you should ensure the fit is comfy CAUTION RISK OF SKIN DAMAGE For comfort safety and effectiveness of this product please see to it that you check the fit of your dog s collar frequently If any skin irritation is observed discontinue the use of the collar for a few days If the condition persists beyond 48 hours see your veterinarian Do not attach a leash to the collar which can result in squeezing the metal probes too tightly against your dog s neck The collar receiver is not designed to be worn constantly We recommend the collar not be worn for more than 12 hours out of every 24 hours period Most dogs feel uncomfortable when wearing the collar for the very first time Don t use any functions before the dog has gotten accustomed to the collar We suggest you give the dog VIBRATION before starting the STATIC SHOCK After a time of training your dog will learn that shock will come after vibration In this way
15. smitter Charge the remote transmitter 1 Connect the charger connector to the charging hole 2 Plug the charger into a standard outlet 3 The red light in the transmitter comes on indicating that charging is taking place 4 Charge the transmitter at least 6 hours for the very first charge even though it may indicate it is fully charged This conditions the battery Other than the first charge please just charge until the red light goes off When charging is complete the red light will turn off automatically 6 Low Battery Indicator signals the need for recharging UT How to use the remote transmitter 1 Toturn on off the transmitter press any button on the transmitter 2 Pressthe MODE button to toggle among 4 different modes Lela RF 3 Press UP DOWN buttons on the right hand side of the transmitter to adjust the intensity level of vibration or static shock 4 1 2 button indicates either channel 1 or channel 2 on the transmitter Select one channel for use with one collar receiver 5 The remote transmitter will go into STANDBY MODE if not operated for 2 minutes and will turn off if not operated for 5 minutes 6 In STANDBY MODE press any button to wake it up When turned off press and hold the MODE button for 1 second to turn it on Step 2 Prepare the Collar receiver Charge the collar receiver 1 2 3 4 Connect the charger connector to the charging jack Plug the charger into a standard outlet
16. the vibration alone can effectively curb the misbehaviors of your dog The STATIC SHOCK might be unnecessary sometimes Step6 Regular Maintenance Check the metal probes for tightness on a weekly basis Rinse the metal probes with alcohol on a weekly basis NB Please turn off the collar receiver before touching the metal probes Check your dog s neck for irritation and wash it on a weekly basis 12 Frequently Asked Questions How old does a dog have to be before using the system Your dog should be able to learn basic obedience commands such as sit or stay The collar receiver may be too large for dogs under 6Kgs Once my dog is trained and has been obeying my commands will he have to continue to wear the collar Probably not but you may need to reinforce training with the collar Can I use the dogtrainer rechargeable training collar with more than one dog Yes you just need to add another collar to the system for a a dog How long can I continuously deliver vibration or static shock to my dog Ten seconds After 10 seconds the transmitter will time out and should be started again Is the collar receiver waterproof Yes but you have to ensure that its charging hole is sealed by the rubber bung Can use the system on aggressive dogs No please do not use this system to correct or eliminate any form of aggression or biting behavior Inthe event that your dog is showing signs of aggressive behavior
17. which is not intended is strictly prohibited In no event shall MGG be liable for any damages arising out of or connected with the use or misuse of this product Buyer assumes all risks and liability associated with the use of this product Modification of Terms and Conditions MGG reserves the right to change the terms and conditions under which this product is offered This equipment is in full compliance with the limits for Class B digital device pursuant to Part 15 of the FCC rules in the United States and Canadian ICES 003 regulations For Europe this product meets the standards for R amp TTE Directive 11955 EEC compliance In some countries this device may be restricted according to frequency or transmission regulations The user is responsible for compliance Unauthorised changes or modifications to the equipment are not approved by MGG and are additionally in violation of FCC regulations Such modifications render the warranty immediately void www mggproducts co nz 17
18. will flash when Y button is pressed and also serves as battery charging indicator 3 LCD Screen Static Mode Under this mode when Y button is pressed the collar receiver will shock static levels can be adjusted from 0 to 100 by pressing UP DOWN button Vibration Mode Under this mode when Y button is pressed the collar receiver will vibrate Vibration levels can be adjusted from 0 to 100 by pressing UP DOWN button Beep Mode Under this mode when Y button is pressed the collar receiver will give a warning beep Light Mode Under this mode when Y button is pressed the green LED light on the receiver will flash every one second making it convenient to help locate your dog in the dark 1 2 button indicates channel 1 or 2 on the transmitter Select one channel for use with one collar receiver 4 Up Down button Press the Up Down buttons on the right hand side of the transmitter to set the level of correction you wish to administer WARNING ALWAYS BEGIN WITH A LOW LEVEL SETTING IN THE INITIAL TRAINING STAGES 5 Channel Button When the CHANNEL button 1 2 is pressed you can sync the collar receiver and the transmitter via different channels 6 Y Button It indicates the LAUNCH button which will send the correction signal to the collar receiver 7 Mode Button It indicates audio vibration and static shock correction modes on the LCD display screen 8 Charging Hole for remote transmitter char
Download Pdf Manuals
Related Search