VHF GUITAR WIRELESS SYSTEM
Contents
1. chord VGW1 VHF GUITAR WIRELESS SYSTEM Item ref 171 848UK User Manual E Li www avsl chord com an NS group brand chord T Caution Please read this manual carefully before operating Damage caused by misuse is not covered by the warranty Introduction Thank you for choosing the Chord VGW1 guitar wireless system This professional wireless set provides a high quality VHF guitar system for freedom of movement without loss of audio quality Please read this manual before using this equipment in order to avoid damage through incorrect operation and to get the best performance from your purchase Contents Please take care when unpacking this product Inspect for any damage and ensure you have the following components e VHF wireless receiver e Mains power adaptor e 6 3mm mono output jack lead e 9V battery PP3 e 6 3mm to 3 5mm guitar to bodypack lead Warning To prevent the risk of fire or electric shock do not expose any of the components to rain or moisture If liquids are spilled on any component stop using immediately allow unit to dry out and have checked by qualified personnel before further use Avoid impact or heavy vibration to any of the components No user serviceable parts inside transmitter or receiver refer servicing to qualified service personnel Safety e Use the power adaptor supplied or an appropriate replacement with the same specification e Avoid ingress of water or particles2. the best available line of sight to the transmitter and connect the DC jack of the supplied power adaptor to the receiver and then plug into the mains outlet Extend both antennas 4 fully upwards and outwards Slightly turn the volume control 11 down on the receiver and switch the power on 8 Turn down the volume of any equipment mixer amplifier etc that the signal will be fed into and then connect the jack lead or an XLR lead optional from the receiver output 6 7 to the input of the equipment Move the switch on the bodypack transmitter 2 to the first notch MUTE the LED should light momentarily continuous dim LED indicates low battery Move on another notch ON and gradually increase the volume control 1 on the receiver then increase the volume on the mixer or amplifier until the sound from the microphone can be heard through the equipment During use it may be useful for the reception of the guitar to be muted for a short period of time e g when tuning or adjusting settings In these circumstances it may be better to move the transmitter switch to the MUTE position which maintains the radio frequency carrier signal but mutes the guitar input When this switch is moved back to the ON position the sound will be immediately restored 171 848UK User Manual D chord If the wireless system is not to be used for more than a few seconds it is preferable to slide the transmitter switch to the OFF posi
3. into the transmitter or receiver e Use alkaline or NiMH batteries in the transmitter and remove if unused for long periods e Observe the correct polarity when replacing batteries Placement e Keep all components out of direct sunlight and away from heat sources e Do not place heavy objects on top of the receiver or transmitter e If rack mounting secure the receiver to a 1U rack tray and do not place heavy equipment above the receiver e Keep the transmitter and receiver away from damp or dusty environments Cleaning e Use a soft cloth with a neutral detergent to clean the body of the transmitter and receiver e To avoid damage do not use solvents to clean the components 171 848UK User Manual chord Bodypack Transmitter 1 2 3 Slide to open sal 1 Gain control 2 Off Mute On switch 3 3 5mm jack socket Slide to close Battery compartment Receiver Rear Panel 4 Antennas 5 D C power inlet 6 6 3mm jack output 7 XLRM output 8 Power On Off switch 9 Power indicator 10 Signal indicator 11 Volume control Operation Slide the front half of the bodypack upwards just enough to reveal the battery compartment and position the supplied 9V battery inside ensure and are the correct way round and then slide back together as before Connect the 6 3mm to 3 5mm jack lead between the guitar and the bodypack transmitter input 3 Position the receiver within
4. tion which mutes and deactivates the radio signal and powers down the transmitter Be sure to turn down the volume of the mixer or amplifier and then switch off the receiver Unplug signal leads from the receiver and mixer or amplifier when moving or packing away If the system is not to be used for long periods of time remove the batteries from the transmitter and unplug the power adaptor from the receiver and the mains outlet Retracting the antennas is also advised when the system is not in use Specifications Audio dynamic range Troubleshooting POWER LED is lit but no SIGNAL LED LEDs are lit but no sound from microphone Microphone output is very loud or Microphone output is very low Check the transmitter battery is good fully charged distorted Reduce Gain on the the mixer amplifier Electronic equipment and should not be disposed with other household or commercial waste at the end of its C 1 622 N Disposal The Crossed Wheelie Bin symbol on the product means that the product is classed as Electrical or m useful life The goods must be disposed of according to your local council guidelines Errors and omissions excepted Copyright 2014 AVSL Group Ltd 171 848UK User Manual
Download Pdf Manuals
Related Search