VIBRATO Operation manual
Contents
1. a cover of the transport box and remove step by step all sides of the box The device is now available on the base plate of the transport packaging and can be withdrawn Setting up 1 If your device is delivered at very low temperature there can be condensation which can damage the electronics Please leave the device 24 hours at its final place so that it can assume the ambient temperature to avoid damage to the electronics through condensation 2 Place the washing machine on a stable plain surface By turning the leveling feet the machine can be aligned horizontally Please ensure that the Foundation has sufficient stability 3 Remove all packaging and transport securing materials from the working area The machine is supplied with packing in the working area supporting the tub lid Remove it carefully from the working area 4 Install the supplied handle bar by vertically pasting them on the glass with the attached doublesided tape Connections Armoire Boitier air lectrique air i ortan sortant Armoire Interrupteur du ll lectrique air r seau ane sortan B il I Connecteur carte memoire SD Chauffage air frais Support fusible Interface USB Alimentation sur secteur 1 Connecting to the mains supply connect the supplied paower cable to the back of the machine then connect the machine to the mains Be sure the power switch is in the off position when connecting the machine to t2. lest arrow which brings you back to the right side and save your changes Also drying can be executed as a step anywhere in the process For drying go to POS and select int TR drying PO1 D signation du programme mp Pos TR Trocknen B2 Isoprop R ER 2 Temperature WL OR 3m a Air chaud 5 00 S sechage AC 5m Nouvelle etape Annulation Here you can set the temperature CA cold air WA warm air HA hot air These temperatures can be adjusted in the settings Selecting ST stop the machine will only drain the basket without fan Also you can set the duration of the drying process Please keep in mind that it takes some time until the heater has reached the set temperature Also it will keep the temperature for a while when switched off by the inertia of the stainless steel air duct After drying the fan will run on to cool down the PTC heating element Please make a test run without workpiece if you have customized the temperatures in the settings If you created all the steps of the cleaning program the arrow will take you back to overview and save the program automatically 10 Run a program If you have created a cleaning program it is now available in the list of programs and can be selected Basically the machine starts in the last executed or changed cleaning program If you want to select a different program turn the ENC until the Name of the program is highlighted or bl
3. of doubt Damage due to improper use of the substances are not subject to the liability of the manufacturer L trade or the supplier of the cleaning fluids e Do not use explosive substances e Do not mix cleaning fluids with each other Do not try to make own repairs Please contact a trained service technician or the manufacturer Unauthorized repairs if not expressly approved by us in writing lead to void the warranty and liability warranty from the manufacturer 5 Technical features Device type Vibrato Reference number of the manufacturer L1 23 Voltage 230v AC 50hz Power max 600 watt Power connected to inactive channel 35 watt Weight without packaging 71 kg Weight with transport packing 102 kg Dimensions 480mm x 480mm x 760mm Country of origin Germany Specific technical shipping information Extracted air Internal 830mm Suction force 26 qm h free movement Guide language English Standard content of delivery Vibrato MSA19 710 ready for connection 1 Piece of power cord with EURO plug 5 Piece glass container 1 Piece ultrasonic tank 5 Piece breakwater for glass containers 1 Piece user manual 1 Piece door handle gt 6 Starting the device Remove the transport packaging Carefully remove the transport packaging Open the screws of the wooden box with a suitable tool Taking care to remove all screws on
4. Operation manual VIBRATO MSA 19 709 710 HORODTEC L outil Forloger oe HOROTEC SA Av L opold Robert 105b Case Postale 837 2301 La Chaux de Fonds SWITZERLAND www horotec ch March Suisse L 441220250595 Rawal 3292393 96 swiss horotec ch r D Export Markets T 41 32911 21 21 F 41 32 911 21 22 export horotec ch L outil ork OP VIBRATO Machine without options and without baskets MSA19 709 Machine without options and with baskets MSA 19 710 1x MSA19 569 3x MSA19570 1x MSA19 571 1x MSA19 572 The following additional functions are available OPT1 extended cleaning movements MSA19 710 A If this option is activated the angle of rotation of all cleaning movements can be adjusted in the settings menu separately OPT2 Vibrasonic MSA19 710 B When this option is enabled the movement of VB in the cleaning programmes can select and customize the settings During this movement it is si to constrain the rotation angle to 36 degrees As well an own sharp acceleration ramp is stored for this movement produces an oscillating vibration movement OPT3 SD card export MSA19 710 C If this option is enabled the machine logs alll eau operations with date time duration used program and used movements as well as the current state of the liquids used during cleaning A serial number is generated for each cleaning that appears after clean
5. ack and confirm the selection It will bring you to the list of programs 3 7 7 P01 sample program Waiting for START S B2 Isoprop 1 FO 3m SF 2m Progress S B4 WF Il Elapsed 00 00 00 2 FO3m SF 2m Total 00 00 00 C S_ B3 Spillsg 3 FO 3m SF 2m You will now see a list of the storage spaces Now select a program and confirm again to load it P02 sample program 2 POS P07 You are now back in the program The cleaning program has always to be started with the start stop button to avoid accidental starts while the operation through the ENC gt P01 sample program Waiting for START S B2 lzopron 1 FO3m SF 2m Progress B4 WF II Elapsed 00 00 00 2 FO 3m SF 2m Total 00 00 00 od S_ BS Sp llsg 3 FO 3m SF 2m Interrupt the cleaning program Is the start stop button pressed during a current cleaning the machine stops and a selection window will appear Confirm with START There are now the following choices available lt 7 CONTINUE The machine just continues the program SKIP STEP The actually executed step is interrupted and skipped This is done as follows The machine automatically detects whether the cleaning basket already had contact with the liquid This is the case it lifts the basket from the fluid and runs the spinning cycle if programmed before it is goes on to the next step If the cleanin
6. g basket had no contact to the liquid the spinning movement will be skipped and the cleaning basket immediately moves to the next step Quit Aborts the entire program with all the steps The basket is lifted out the fluid immediately and moved back into the Park loading position If the door is opened during operation all movements are stopped and the spindle released The Same menu as above appears 11 Settings The global parameters of the machine can be set in the menu Settings Software V3 x x Meng Here all settings can be made For example the rotational speed of the cleaning movements and in case the Option extended movements is active also the rotation angle of the single movements can be adjusted To test the speed immediately please press the START STOP button Settings Movements Heating Sik 150 UPM WA 35C FT 300 UPM HA 65C SA 150UPM 6U Temp 25 8C FA 300 UPM SU SO 200UPM 6U Buzzer OFF FO 400 UPM AU SX 200UPM AU FX 400UPM SU VB 500UPM 0 2U SF 1000 UPM 0 UPM Speed These speeds are global If you choose 60 rpm for the movement of LO the basket oscillates with 60 UPM every time you select LO as cleaning movement Abbreviations and explanation of the cleaning movements Abbreviation Movement Description ST Standstill No turning ST Slow turning t 2 left side then right FT Fast turning t 2
7. he power 2 Switch on the machine The control will perform a brief self test and then start the initialization This means that all axes will go to the reference point to determine their current position This process is repeated at each switching on again as well as after the change of the cleaning tanks 3 Your machine is now ready for use and you can start to be assembles with the cleaning tanks 7 Operation The operating concept The operating concept of the Vibrato is intuitive All functions can be executed using only two controls Encoder ENC Start Stopp button To the left of the display is the start stop button which is used to start the cleaning programs or stop it It always has to be used to start any motion The rotary encoder with confirmation function is located right of the display A knob which can turned and also be pressed ENC With this control can the menu can be navigated settings can be made and confirmed and numbers and letters entered With the help of the ENC you can move the cursor in the display This will allow values to change represented by a bracket to the value Value If you want to change the value press briefly on the ENC which changes the clamp around the value gt value lt The Value itself now can be changed by turning the ENC To confirm press again on the ENC the value is taken the clamp will change back to value and can be moved by turning to a different posit
8. ined application field of this machine e Make sure that your mains voltage corresponds to that indicated on the plate on the back of the machine The equipment you have purchased may only be connected to a 230 volt AC 50 Hz mains socket e Persons without proper instruction may not use the appliance unless they are supervised separately by a legitimate service and instructed sustainable e The device is not to be suitable for being operated by children or by not trained personnel Exclude all possibilities for unsupervised use by untrained and unauthorized persons e Ensure that during cleaning of the unit the power switch is set to zero and the power cord is disconnected from the electricity network Make absolutely sure that until the completion of any cleaning or maintenance work the use of the device by other people is not possible e Make sure that the machine is only operated only in a well ventilated room or connected to an external exhaust e Take care when loading the machine not to damage any mechanical or electrical parts When suspected damage of any kind shut the machine down and please make sure that a further use by others is not possible e Incase of damage of the machine or the cable further use is strictly prohibited e When using cleaning fluids take care to use them according to the safety instructions of their respective manufacturers Do not use any cleaning solutions that are not approved by us Please Inquire in case
9. ing in the display and a TXT file is written to the SD card which contains all the information OPTA Master slave MSA19 710 D If this option is activated a relay is switched synchronous to the exhaust fan of the is It can be used to connect external exhaust systems and control them with the machine Index Introduction Declaration of conformity Safety instructions Technical fatcs Initial start up Operation Equipping Creating cleaning programs 10 Performing cleaning programs 11 Settings 12 Optional functions 13 Cleaning and maintenance 14 Disposal O CON ODM ww NN FE 2 Introduction Dear Sir or madam many thanks for purchasing this product With the purchase of the Vibrato MSA19 710 you have acquired a fully automatic washing machine for cleaning watch movements and movement parts with completely free programmable cleaning processes The machine offers the possibility to use 5 cleaning tanks and one ultrasonic tank as well as a drying station in free programmable process Please keep the operation manual 3 Declaration of conformity This device complies with European standards CE according to 2006 42 EC directives A copy of the Declaration of Conformity can be provided on request 4 Saftey instructions To avoid male functions damages of the machine or injuries please cearfully read and obey the following safety instructions and standards for proper use resp the clearly def
10. ion in the display You can leave any menu by clicking the Arrow on the upper right side It will bring you back and the changed values are automatically saved when you exit via the arrow If letters and numbers can be entered E g for the naming of the tanks or programmes the cursor is set to the desired position and confirmed by pressing Now the desired letter number can be selected by turning and confirm by pressing So you act until the complete name is entered Please keep in mind that the length of any text is sometimes limited to represent them in the program 8 Assembly of cleaning tanks 1 Please insert the breakwaters into the glasses Bend the stainless steel alloy mesh circular not too tight so that they are inside with some tension on the glass Please ensure that the cleaning basket can rotate freely with sufficient distance The breakwater should be applied to the glass They are used to prevent rotation of the fluid 2 Fill you the glasses up to the mark with the desired cleaning fluid Pay attention to the proper handling of the respective fluids according to the instructions of the manufacturers Now the glasses can be load into the machine In addition the Vibrato offers an own menu item under which you can make the loading and designation of the tanks fluids Menu Jo Switch to the menu Cleaning tanks Manage cleaning tanks m B1 Ultrasonic C 0 B2 SubstanzB 0 B3 Substanzc C 0 B4 S
11. isplay and a TXT file is written to the SD card which contains all the information OPT4 Master slave If this option is activated a relay is switched synchronous to the exhaust fan of the machine It can be used to connect external exhaust systems and control them with the machine 13 Cleaning and maintenance Like any mechanical movement the mechanics of this machine requires some maintenance The guides of the B axis vertical movement are maintenance free dry running polymer bearings which require no maintenance over their lifetime The spindle bearing arrangement consists of a maintenance free dry running full ceramic bearings as well as a dry running Teflon shaft seal ring which both also come out without lubrication Every 8 weeks e The trapezoidal screw which provides the vertical movement of the B axis has to be controlled and if necessary applied some grease To do this we recommend you the spindle grease best L1 ZBHOO3 applied with a bristle brush through the slots in the front panel e Check air filter of the air inlet f the fan heater and control cabinet and if necessary clean or exchange it The black powder coated parts of the machine can be cleaned with a soft cloth and some washing up liquid DO NOT use solvent based cleaner Bare stainless steel parts can be cleaned with all commercially available cleaners and sovents if necessary 14 Disposal If you want to throw your machine away do not place i
12. left side then right SA Slow alternating n turns left then n turns right FA Fast alternating n turns left then n turns right SO Slow oscillating n turns left then 0 7n turns right FO Fast oscillating n turns left then 0 7 n turns right SX Slow extra osc up down n turns left then 0 7 n turns right Up and down FX Fast extra osc up down n turns left then 0 7 n turns right Up and down VB Vibrasonic OPTIONAL n turns left then 0 7 n turns right fast acceleration vibrasonic movement Now you can globally set the rotation speed for every single movement Optionally also the rotation angle Is adjustable Otherwise there are standard angles by factory Heating The temperatures for WA warm air and HA hot air can be set Please note that the heating due to the air tube made of stainless steel has a certain inertia By pressing the START stop button you can also test the heating and directly read the temperature of the air at the sensor Please take it first attempt without workpiece to approach the ideal heating temperature and time and avoid overheating of the workpiece Beeper Select whether the beeper also sounds while turning the ENC or only while pressing it gt gt 12 Additional functions Under the menu Additional functions you see the status of unlocking additional functions and unlock them after ordering Mens If you select the menu point the machine show
13. lly to the counter reset button which resets the two counters 7 In the window Cleaning cycles you can enter a maximum number of cleaning the solution will be used The progress bar in the parent overview screen is generated from this number The counter will count the previous use In the window Age in days you can set the maximum duration of use in days Analog to the cleaning cycles the progress bar is generated since the last change of the bath ATTENTION If for both Cleaning cycles and Age in days a maximum value is defined the progress bar displays the value which first reaches the limit If during a cleaning the maximum use of a solution is reached a note appears after cleaning By accepting the menu will automatically go to the overview screen of the tanks There you can identify the bad whose limit is reached and change it In the Name box below the tank can be given an individual name E g the containing cleaning fluid B1 stands for position 1 of the bath in the machine If no name is entered the BAD NAME field is not changed it shows the default name or the position only if the default name is deleted Using the arrow right above you can switch back to the tank overview and analog all tanks can be adjusted and changed After leaving the bath changing menu the machine performs a homing of the axis 9 Creation of programs You have now equipped your machine with the gla
14. ning F 2 00 In this step the default values are pre selected now and can be customized according to your wishes Rotate the rotary encoder to the field left in the display which you want to change and press once on the rotary encoder to change the value 7 At every step you can set the following parameters Pos the position which tank shall be used If you have submitted names to the baths in the bath changing menu the name is also displayed Here bath 2 was named with Isoprop By turning the encoder you can choose the desired tank Also drying can be inserted as a single step at any point Movement herewith the cleaning movement in the tank is meant You can customize all speeds of cleaning movements in the Settings menu which is explained later in this manual There are following movements to choose from LD SD LW SW LO SO LX SX VB optional 03 00 Here you can set the time of the movement in the cleaning tank 3 00 Minutes have been set here Spin here you can adjust whether after cleaning the spinning is executed how long and at what speed There are following options to choose from ST SL SM SS 2 00 Here you can set the spin time here 2 00 minutes If 0 00 is set there will be no spinning at all Through the button delete you can delete the complete step displayed on the left side To confirm your settings of each step click on the
15. ram The input is carried out by turning the encoder a letter is selected and confirmed by pressing Steps shows the number of steps the program goes through If still no steps have been created the number 0 appears here Duration the duration is determined from the individual cleaning in the tank the spinning and drying as well as the duration of the movement As soon as a cleaning program has been fully executed the machine determines the duration of the movements and the total duration and display them from now on numerically and as a progress bar accurate Counter here it is counted how often a program has already been used Counter reset to reset the counter select counter reset and confirm by pressing on the ENC Steps To create a step chain a sequence of various cleaning steps select steps and confirm by pressing the ENC You will now see a blank step chain with start and new step To create a cleaning step select the new step field and confirm with the ENC Left you see the statement on the menu It is also possible to insert a new step at any point of an existing program with the START STOP button 7 P01 sample program m START ENC New step New Step After confirming a new step is inserted shown left whose parameters can be set as follows P01 sample program mp Pos B2 lsoprop S B2 Isoprop 1 Movement FO OS SP ain nr giy Spinning SF Spin
16. s the currently unlocked features Furthermore the other functions can be unlocked Optional functions m Aktivated optional functions OPT1 extended cleaning movements NEIN OPT2 Vibrasonic NEIN OPT3 Export to SD card NEIN OPT4 Master Slave NEIN Aktivate optional functions REQ pwo C JL JL L To unlock an optional feature you order it and then contact us by phone to get the code The machine generates a new request code REQ at every single switching on It is comprised of 4 pairs of numbers From this request code we generate password to unlock of the additional features 3 The following additional functions are available OPT1 extended cleaning movements If this option is activated the angle of rotation of all cleaning movements can be adjusted in the settings menu separately OPT2 Vibrasonic Dieso ption is enabled the movement of VB in the cleaning programmes can select and customize the settings During this movement it is possible to constrain the rotation angle to 36 degrees As well an own sharp acceleration ramp is stored for this movement produces an oscillating vibration movement OPT3 SD card export If this option is enabled the machine logs all cleaning operations with date time duration used program and used movements as well as the current state of the liquids used during cleaning A serial number is generated for each cleaning that appears after cleaning in the d
17. sses and liquids and can now create a cleaning program according to your needs Basically a cleaning program called Step chain consists of cleaning steps while also drying is considered as a single step and can be fitted into a cleaning program on every position All the steps can be programmed in any order and are not bound by the order of the tanks in the machine As well individual tanks can be repeatedly used with different cleaning moves in one program To create or change cleaning programs first go to the main menu and select Manage programs Men se Manage programs Manage cleaning tanks Optional functions Service menu Now you are in the program list You can see the 32 storage places P0O1 to P032 and in case a name is used also the name of the program Manage programs mp P01 sample program 1 PO2 sample program 2 PO3 PO4 POS To create or change a program select the corresponding storage place After confirming you will find an overview of the selected storage space 3 P01 sample program mp Name P01 sample program Steps O Duration unknown Counter O You can now move the cursor by turning of the ENC and by pressing on the appropriate location vary the value as described earlier in this guide In the field name it is advisable to give a descriptive name to the program so that other users can easily identify the prog
18. t into the normal household garbage but take local collection point WEEE Reg Nr DE95245907 24
19. ubstanzD 0 B5 SubstanzE 0 B6 SubstanzF 0 Here you can see the individual tanks B1 to B6 and right aside the associated name or the default name substance A F These can be replaced while changing the tanks by your own names Consider the contents of the bath here to use The bath position identifies the position of the individual glass on the turntable and is starting with the ultrasonic bath B1 numbered counterclockwise It is used for identification of the glass and its position on the turntable and cannot be changed On the right side you see a progress bar that shows the status of the respective tank if a maximum duration of use was deposited Turn the ENC until the desired position is selected where you want to place your glass jar Confirm the selection by pressing the ENC You now see overview of each tank position Replace tank Age in days Maximum 30 Maximum 30 Counter 00 Counter 00 D J0 If OM Last Replacment 01 01 2012 22 03 Tank name B1 Ultrasonic If you press the button Bath change the selected tank is turned to the front to allow an exchange Please keep in mind that for safety reasons the door must be closed If it is not closed the machine prompts you to close the door while turning If the selected position has turned to the front the buzzer sounds and the door may be opened to change or install the tank After successfully changing the cursor jumps automatica
Download Pdf Manuals
Related Search