Home

POC-120 User`s Manual

1. or just simply press the power button In case of system halts you can press and hold the power button for 5 seconds to compulsorily shut down the system Please note that a 5 seconds interval is kept by the system between two on off operations I e once turning off the system you shall wait for 5 seconds to initiate another power on operation 2 2 2 Reset Button USB2 0 m The reset button is used to manually reset the system in case of any abnormal condition To avoid unexpected operation the reset button is hidden behind the front panel You need to use a pin like object to push the reset button um p guts Copyright 2015 Neousys Technology Inc All Right Reserved Page 10 of 53 POC 120 Series User s Manual 2 2 3 LED Indicators 1 PWR WDT HDD RESET o o o IO USB2 0 m b g There are three LED indicators on the front panel PWR WDT and HDD The descriptions of these three LED are listed in the following table indicator Coor Descriptor HDD Red Hard drive indicator flashing when mSATA module is active 2 2 4 USB 2 0 Connector 14 VGA There are totally one USB 3 0 port and two USB 2 0 ports on POC 120 series One of USB 2 0 ports is located on the front panel By BIOS default this USB 2 0 port is operated in EHCI Enhanced Host Control Interface mode and are compatible with USB 2 0 USB 1 1 and USB 1 0 devices Legacy USB support is provided so you can use USB k
2. 1 1 COM1 Operation Mode sse 38 4 1 2 USB xHCI Mode Configuration sse 38 4 1 3 Chipset SATA Mode T iwi aaNet 39 4 1 4 C States and Max C States ccn 40 4 1 5 Wake on LAN Option 41 4 1 6 Power On after Power Failure Option etnies 41 4 1 7 Watchdog Timer for Booting sse 42 4 1 8 Select a Boot Device sss 43 4 2 Operating System Support emnes 45 A DVE AST MATO M UT 46 4 3 1 Install All Drivers Using One Click Driver Installation 46 4 Foscari DAVES Man aly m 47 Appendix A Using Watchdog Timer eene 49 Install WDT and DIO LIDFALV ssssoosoiaisiiseei bito qttam utn dns DoD tas A 49 VV ABA Uere RCTS FENG C m T o t D TTD 52 TELINA D M nea 52 Sen A D 6 52 Selga aD A EE EA E E A TEE E E TA 53 gC OND Meee ee ee 53 10191714 D T Aen ne ee ee 53 Dp LM Copyright 2015 Neousys Technology Inc All Right Reserved Page 4 of 53 POC 120 Series User s Manual Declaimer This manual is intended to be used as a practical and informative guide only and is subject to change without prior notice It does not represent commitment from Neousys Technology Inc Neousys shall not be liable for direct indirect special incidental or consequential damages arising out of the use of the product or documentation nor for any infringements upon the rights of third parties which may result from such use Declaration
3. EE T 3 Push the non latched switch will turn on the system the PWR LED indicator on the front panel is on at the same time Push the non latched switch when system is on will turn off the system If your operating system supports ATX power mode i e Microsoft Windows or Linux push the power button causes a pre defined system behavior such as shutdown or hibernation See Copyright 2015 Neousys Technology Inc All Right Reserved Page 33 of 53 POC 120 Series User s Manual 3 6 4 To Power on POC 120 Using Wake on LAN Function Wake on LAN WOL is a mechanism to wake up a computer system from a S3 standby 4 Hibernate or S5 system off with standby power state via issuing Subnet Directed Broadcasts SDB or a magic packet POC 120 series implements the Wake on LAN function for its first GbE port a To enable WOL function and power on you POC 120 please follow the steps listed below 1 When POC 120 boots up press F2 to enter BIOS setup utility 2 Enter the Power menu And configure the Wake On LAN option as Enabled This setting enables the Wake on LAN function for POC 120 series Please refer to section 4 1 5 for the instruction of configuring this BIOS option 3 In Windows 7 system identify the Local Area Connection of corresponding Intel 1210 Gigabit Controller and click the Configure button 4 Local Area Connection 5 Properties om Networking Sharing Connect using P Intel R 1210 Gig
4. L RR Toso S A LEA gt uk 2 Tile the DDR3L SODIMM module and insert it to the SODIMM socket As it s firmly contacted with socket connectors press it down until the clamps of the socket snap into the latching position of SODIMM module e pm Copyright 2015 Neousys Technology Inc All Right Reserved Page 25 of 53 Merk iim eem eet POC 120 Series User s Manual 3 3 Install a mSATA SSD The mSATA port of POC 120 is located on the PCBA It accommodates a full size mSATA SSD module To installa mSATA SSD on mSATA port please follow the steps listed below below 1 Follow the steps in section 3 1 to dissemble your POC 120 series You can see the mSATA port expos V bir ADELE EAA ESEERAREDSSUAAEARSAASEAAAPARDAREARSLAGSAAAAADGS REAAN EIDE LN ORI EAINAESEAAAA EH LEA AL ESS z Dn int Jag we ale a ie BOD i E A mars r v B aot 7 Na p x gt aana leeti gE sees Jai M ow i d T N or MM al f i d CVEY ANA aa a K i G9 bum peu P P 2 Tilt the mSATA SSD module and insert it to the mSATA port And Fix the mSATA SSD module with two M2 5 P head screws D wa CE FUTT T TTL LET amen essere Pwiaiao TAIWAN iui f m io TU RoHS lix His Boobie dE Fila diii nnam e Copyright 2015 Neousys Technology Inc All Right Reserved Page 26 of 53 POC 120 Series User s Manual 3 4 Mount your POC 120 Series
5. O e aE mmm 14 292 U B2 D COMECON eonan AE E 14 23S COM PONS enaurar i TEE EEES E a EEA EEA a S a 15 2 3 4 2 Pin Spring Clamp Terminal Block for DC Input 16 24 Mtema bb IIA TION Sacco crwth ea orcad tutt IIR Msi eae bul trenes 17 2 4 1 Remote On Off Control ene 17 2 4 2 MSATA GOMMECION essendi vester dba tenter P Cr dbi i e bri 18 2 4 3 DDR3L SODIMM Socket eee een 18 2 5 POC 120 Mechanical DiMenSIOn seems 20 oes ae TOD 2 ee 20 25 2 Front VIEW E 21 PI SIGS VON or eari EA E EE IEEE i 21 ZA BONOT VIW aai T O SNA ISA E ee 22 Chaple S Ge too aT oeno o 0 70005 A 23 3 1 Dissemble your POC 120 Series accen eee eee 23 3 2 Install a DDR3L SODIMM Module seem 25 SSMA MSATA S E 26 3 4 Mount your POC 120 Series sss sse rire nner 27 3 4 1 Mount your POC 120 Outside in on a Surface ens 27 J ae Copyright 2015 Neousys Technology Inc All Right Reserved Page 3 of 53 POC 120 Series User s Manual 3 4 2 Mount your POC 120 on the DIN Rail tin 28 3 5 Connect DC power to you POC 120 sss eene 29 3 6 Power on vour ms Oren bd 0 m nee eee ee EEEN 31 3 6 1 To Power on POC 120 Using the Power Button 31 3 6 2 To Power on POC 120 Using an Latched Switch AT mode 31 3 6 3 To Power on POC 120 Using an Non latched Switch ATX mode 32 3 6 4 To Power on POC 120 Using Wake on LAN Function 34 eile 4 Bis and DAVE MEM 37 a T BIOS SUTIN c M 37 4
6. POC 120 series provides two ways of mounting The chassis itself is designed to be used as a mounting bracket which can be mounted outside in Neousys also offers the option of DIN rail mounting clip so you can mount POC 120 on a DIN rail To mount your POC 120 please refer to the information listed below 3 4 1 Mount your POC 120 Outside in on a Surface There are two nuts with M4x0 7 thread on the bottom side of POC 120 You can fix it outside in using two M4 screws This is applicable when you want to deploy POC 120 on a flat surface M4 Tapped 2X ow 4 Screw 2X Jg ueri mts Copyright 2015 Neousys Technology Inc All Right Reserved Page 27 of 53 POC 120 Series User s Manual 3 4 2 Mount your POC 120 on the DIN Rail Neousys also provides the option of the DIN rail mounting clip With the mounting clip you can fix POC 120 on a DIN rail This option is useful when you want to deploy POC 120 inside an equipment cabinet where DIN rail is available Le Copyright 2015 Neousys Technology Inc All Right Reserved Page 28 of 53 POC 120 Series User s Manual 3 5 Connect DC power to you POC 120 POC 120 series uses a 2 pin spring clamp terminal block to accept 8 35V DC power input lt provides the way for directly wiring the DC power To connect DC power via the terminal block please follow the steps listed below 1 Make sure the external DC power supply is power off or disconnected
7. before wiring 2 Carefully identify the positive and negative contacts of your DC power supply and spring clamp terminal block The polarities between DC power supply and terminal block must be positive to positive and negative to negative 3 Make sure wires from power supply are with gauge of 16 24 AWG and stripping length of 8 mm Insert wires to the spring clamp terminal block and push them to the end The terminal block shall clamp wires securely 2 cue iy Copyright 2015 Neousys Technology Inc All Right Reserved Page 29 of 53 POC 120 Series User s Manual 4 To eject wires if necessary use a slotted screwdriver to push the ejector key to the end and you are able to pull out the wires Caution 1 POC 120 accepts 8 35 VDC when using terminal block for DC input Please make sure the voltage and polarity of DC power is correct before you connect it to POC 120 Supplying a voltage over 35V will damage the system p Copyright 2015 Neousys Technology Inc All Right Reserved Page 30 of 53 POC 120 Series User s Manual 3 6 Power on your POC 120 For beiter flexibility of operation POC 120 series provides four alternatives to power on your POC 120 You can turn on your POC 120 by pressing the power button using an external latched or non latched on off switch or by sending a special LAN packet In this section we ll illustrate these four ways to power on your POC 120 3 6 1 To Power on POC 12
8. is BIOS in prior to OS installation to avoid possible issue Once OS is installed and corresponding xHCI driver is installed you can enable xHCI mode to work with USB 3 0 port on POC 120 To set xHCI mode 1 When POC 120 boots up press F2 to enter BIOS setup utility q eee Copyright 2015 Neousys Technology Inc All Right Reserved Page 38 of 53 POC 120 Series User s Manual 2 Goto Advanced USB Configuration 3 Set the xHCI Mode option to according to the following conditions Operating System xHCI Mode Windows 7 32 64 bit Disabled Linux Ubuntu Fedora OpenSuSE CentOS Windows 8 8 1 32 64 bit 4 Once OS and corresponding xHCI driver is installed you can restore the xHCI Mode option to Auto xHC 1 Hode Disabled 4 1 3 Chipset SATA Mode The SATA controller of POC 120 series supports two modes of operations IDE and AHCI mode IDE mode configures SATA controller to access SATA interface in legacy IDE mode and is compatible with most storage devices AHCI mode which exposes SATA s advanced capabilities such as hot swapping and native command queuing can deliver better performance for disk read write As POC 120 series no longer supports Windows XP we highly recommend you to set Chipset SATA Mode to AHCI for better system performance To set Chipset SATA mode 1 When POC 120 boots up press F2 to enter BIOS setup utility 2 Goto Advanced SATA Configuration 3 Set
9. output supporting up to 2560 x 1600 resolution 1x software programmable RS 232 422 485 COM1 1x RS 232 COM2 1x USB 3 0 port via native XHCI controller 2x USB 2 0 ports Serial Port C OD UJ Audio Storage Interface mSATA Power Supply DC Input 1x Speaker out 1x full size mSATA socket Built in 8435 VDC DC input 2 pin spring clamp terminal block for DC input Typical 6 7 W 0 28 A 24 V Full loading 12 W 0 5 A 24 V Input Connector Power Consumption Dimension 149mm D x 105 mm W x 34mm H Weight 0 9 kg Mounting Wall mount Standard or DIN rail mount Optional Environmental Operating 25 C 70 C with mSATA 100 CPU loading Temperature Storage 40 C 85 C Temperature 10 90 non condensing Operating 5 Grms 5 500 Hz 3 Axes w SSD w o add on card according to Shock Operating 50 Grms Half sine 11 ms Duration w SSD w o add on card according OC to IEC60068 2 27 CE FCC Class A according to EN 55022 amp EN 55024 Ful loading power consumption is measured with 2GB DDRSL memory and one mSATA SSD installed under the following conditions 1 100 loading for Atom E3826 CPU 2 100 loading for 3D graphics MERAS Copyright 2015 Neousys Technology Inc All Right Reserved Page 7 of 53 POC 120 Series User s Manual 3 100 loading for memory read write The 100 CPU loading is applied using Passmark BurninTest v7 0 For detail te
10. 0 Using the Power Button This is the simplest way to turn on your POC 120 The power button on the front panel is a non latched switch and behaves the AT X mode on off control As DC power is connected push the power button will turn on the system as well as the PWR LED indicator Push the button when system is on will turn off the system If your operating system supports ATX power mode i e Microsoft Windows or Linux push the power button causes a pre defined USB2 0 mw system behavior such as shutdown or hibernation 4 3 6 2 To Power on POC 120 Using an Latched Switch AT mode PWR WDT HDD RESET VGA o oo For an application which places POC 120 inside a cabinet it s useful to control the on off of the system using an external switch POC 120 series provides an on board connector for detail please refer to section 2 4 1 for connecting a latched non latched switch and behaves either AT mode or ATX mode power on off control When using the AT mode on off control you need a latched switch The external latched switch controls the feed in of DC power When the switch is closed the DC power is break off When it s opened the DC power is feed in To power on POC 120 using an external latched switch AT mode please follow the steps listed below ae Copyright 2015 Neousys Technology Inc All Right Reserved Page 31 of 53 POC 120 Series User s Manual 1 Prepare a latched switch with a 2 pin 2 0mm pitch conn
11. AN option 1 When POC 120 boots up press F2 to enter BIOS setup utility 2 Goto Power 3 Enable disable the Wake on LAN option according to your application Wake on LAN lt Disabled gt Enabled 4 1 6 Power On after Power Failure Option This option defines the behavior of POC 120 series when DC power is supplied S0 Power On oystem is powered on when DC power is supplied o5 Power Off oystem is kept in off state when DC power is supplied When you want to use the AT mode remote on off control function you have to set this option to SO Power On Please refer to section 3 6 2 for instructions of using AT mode remote on off control function To set Power On after Power Failure option 1 When POC 120 boots up press F2 to enter BIOS setup utility 2 Goto Power 3 Set the Power On after Power Failure option to a proper value for your POC 120 MER Copyright 2015 Neousys Technology Inc All Right Reserved Page 41 of 53 POC 120 Series User s Manual Power On after Power Failure Sb Power Off gt 0 Power On 4 1 7 Watchdog Timer for Booting The BIOS of POC 120 series has a useful feature which allows users to use the watchdog timer to secure the booting process You can specify the timeout value for watchdog timer Once the watchdog timer expires the BIOS issues a reset command to initiate another booting process You can also set the behavior of how to stop the w
12. All Right Reserved Page 45 of 53 POC 120 Series User s Manual 4 3 Driver Installation Neousys Technology Inc provides a very convenient utility in Drivers amp Utilities DVD to allow the One Click driver installation This utility automatically detects your Windows operating system and installs all necessary drivers to your POC 120 series with just one mouse click 4 3 1 Install All Drivers Using One Click Driver Installation 1 Insert the Drivers amp Utilities DVD into a USB DVD drive attached to your POC 120 A setup utility launches and the following dialog appears Automatic Driver Installation Browse this DVD Open User s Manual neouss i Neousys Setup Utility Rev 1 60 Exit www neousys tech com 2 Click on the Automatic Driver Installation The setup utility will automatically detect your Windows operating system and install all necessary drivers According to different versions of Windows the installation process takes about 6 8 minutes Once driver installation is done the setup utility reboots your Windows and your system works normally afterward pem Copyright 2015 Neousys Technology Inc All Right Reserved Page 46 of 53 POC 120 Series User s Manual 4 3 2 Install Drivers Manually You can also manually install each driver for POC 120 series Please refer to the following information about installing drivers for different operating system Windows 7 32 bit The re
13. BYTE unit 1 unit is second BOOL bRet SetWDT tick unit timeout value is 255 seconds J ee Copyright 2015 Neousys Technology Inc All Right Reserved Page 52 of 53 POC 120 Series User s Manual StartWDT Description Start countdown of WDT When WDT is started the WDT LED indicator starts to blink in a frequency of 1Hz If no ResetWDT or StopWDT is invoked before WDT is counted to 0 the WDT expires and system resets Parameter None Return Value If the timeout value is given in correct format this function returns TRUE otherwise FALSE Usage BOOL bRet StartWDT ResetWDT Description Reset the timeout value to the value given by SetWDT If no ResetWDT or StopWDT is invoked before WDT is counted to 0 the WDT expires and system resets Parameter None Return Value Always returns TRUE Usage BOOL bRet ResetWDT StopWDT Description Stop the countdown of WDT When WDT is stopped the WDT LED indicator stops blinking Parameter None Return Value Always returns TRUE Usage BOOL bRet StopWDT ee Copyright 2015 Neousys Technology Inc All Right Reserved Page 53 of 53
14. C Address is 78h DOh 04h OAh OBh OCh DESTINATION SOURCE MISC FF FF FF FF FF FF 78 DO 04 0A OB OC 78 DO 04 0A OB OC 78 DO 04 0A OB OC 78 DO 04 0A OB OC 78 DO 04 0A OB OC 78 DO 04 0A OB OC 78 DO 04 0A OB OC 78 DO 04 0A OB OC 78 DO 04 0A OB OC 78 DO 04 0A OB OC 78 DO 04 0A OB OC 78 DO 04 0A OB OC 78 DO 04 0A OB OC 78 DO 04 0A OB OC 78 DO 04 0A OB OC 78 DO 04 0A OB OC MISC CRC There are some free tools available on Internet that can be used to send a magic packet Please refer to the following link to understand more about Magic Packet http en wikipedia org wiki Wake on LAN L a Preeteg Copyright 2015 Neousys Technology Inc All Right Reserved Page 35 of 53 POC 120 Series User s Manual e Wake on Magic Packet from power off state When checking this option POC 120 can wake from S5 system off with standby power state when receiving a magic packet ets Copyright 2015 Neousys Technology Inc All Right Reserved Page 36 of 53 Feb POC 120 Series User s Manual Chapter 4 BIOS and Driver 4 1 BIOS Settings POC 120 series is shipped with factory default BIOS settings cautiously programmed for best performance and compatibility In this section we ll illustrate some of BIOS settings you may need to modify Please always make sure you understand the effect of change before you proceed with any modification To Enter BIOS setup When POC 120 is booting up press F2 to enter BIOS setup utility Use following keys t
15. Page 50 of 53 POC 120 Series User s Manual When you programming your WDT or DIO program the related files are located in Header File Include Library File Lib L JFunction Reference Manual JL JSample Code Sample WDT Demo Watchdog Demo Sample DIO_Demo Polling I O Demo Sample COS_ Demo Change of State Interrupt Demo Sample DTIO_ Demo DTIO Demo Sample DTFO_Demo Trigger Fan out Demo Sample PoE_ Demo PoE per port Control Demo These sample programs can not work with POC 120 ne Copyright 2015 Neousys Technology Inc All Right Reserved Page 51 of 53 POC 120 Series User s Manual WDT Function Reference InitWDT Description Initialize the WDT function You should always invoke InitWDT before set or start watchdog timer Parameter None Return Value Heturns TRUE if initialization successes FALSE if initialization failed Usage BOOL bRet InitWDT SetWDT Description Set timeout value and unit for watchdog timer When InitWDT is invoked a default timeout value of 255 seconds is assigned Parameter tick WORD value to indicate timeout ticks tick should be a value of 1 16 if unit is O minute tick should be a value of 6 1027 if unitis 1 second unit BYTE value 0 or 1 to indicate unit of timeout ticks 0 unit is minute 1 unit is second Return Value If value of unit is correct 0 or 1 this function returns TRUE otherwise FALSE Usage WORD tick 255
16. User s Manual 2 5 4 Bottom View M4 Thread L Le Copyright 2015 Neousys Technology Inc All Right Reserved Page 22 of 53 POC 120 Series User s Manual Chapter 3 Getting Start In this chapter we ll illustrate how to disassemble your POC 120 and install peripheral devices Please follow the correct procedures to prevent any damage on your POC 120 series 3 1 Dissemble your POC 120 Series 1 Unscrew two M3 F head screws on the bottom side and one hex socket cap screw to remove the front panel Copyright 2015 Neousys Technology Inc All Right Reserved Page 23 of 53 nual POC 120 Series User s Ma heat sink 4 hex bolts on the top of the 2 Unscrew 3 y LT MADA E Page 24 of 53 POC 120 Series User s Manual 3 2 Install a DDR3L SODIMM Module Note Please make sure youre installing a 1 35V DDR3L SODIMM module on POC 120 Installing a 1 5V DDR3 SODIMM will cause system failed to boot 1 Follow the steps in section 3 1 to dissemble your POC 120 series You can see the DDR3L socket exposed r DL 0mm FR e c Ets al aes J An osas T 4 ia E TUTTTTTTLTmmmmEWA N m m us d a LEE Pe eV EFIE BAR LED ELEREA EVA LLL EELAR LEAL ASSES BASS LIGA AAS EASE a LLLLLLLLLLLLLLLLLLLLLLL LET LIT WR iy lt LC see LALACI m A tu wu fey mu zyj NX XI MN s TTTTTTTTTITITI jf L e E OA T Tal agg ay A EEs us ER zT CEE n tjellis R BO
17. ab amp Network Connection 5 This connection uses the following tems z 4 E QoS Packet Scheduler V dil File and Printer Sharing for Microsoft Networks w 4 intemet Protocol Version 6 TCP IPv6 v 4 Intemet Protocol Version 4 TCP IP v4 4 Link Layer Topology Discovery Mapper L O Driver 4 Link Layer Topology Discovery Responder haal Unnstal Description Allows your computer to access resources on a Microsoft network Lo Copyright 2015 Neousys Technology Inc All Right Reserved Page 34 of 53 4 POC 120 Series User s Manual Click the Power Management tag and check the following two options accordingly Generi Lic Speed Advanced Power Management intel Power Saver and Wake on LAN Options Power Saver Options AA Respond to ARP requests without waking system v Respond to NS requests without waking system J Energy Efficient Ethemet Wake on LAN J Wake on Magic Packet Wake on Magic Packet Enables a management station to bring the computer out of a l standby or hibernation when a Magic Packet is sent directly to the adapter e Wake on Magic Packet POC 120 can wake from S3 or S4 state when receiving a magic packet The magic packet is a broadcast frame containing anywhere within its payload 6 bytes of all 255 FF FF FF FF FF FF in hexadecimal followed by sixteen repetitions of the target computer s 48 bit MAC address For example NIC s 48 bit MA
18. atchdog timer There are two options in BIOS menu Automatically after POST and Manually after Entering OS When Automatically after POST is selected the BIOS automatically stop the watchdog timer after POST Power On Self Test OK When Manually after Entering OS is selected it s user s responsibility to stop the watchdog timer when entering OS This guarantees the system can always boot to OS otherwise another booting process will be initiated For information about programming watchdog timer please refer to Appendix A Using W Watchdog Timer and DIO To set the watchdog timer for boot in BIOS 1 When POC 120 boots up press F2 to enter BIOS setup utility 2 Goto Boot menu 3 Disable or select timeout value for WDT for Booting option 4 Once you give a timeout value the WDT Stop Option option appears You can select either Automatically after POST or Manually after Entering OS 2 ies Po Copyright 2015 Neousys Technology Inc All Right Reserved Page 42 of 53 POC 120 Series User s Manual ps WDT Stop Option lt Automatically after POST gt Automatically after POST 4 1 8 Select a Boot Device When you have multiple bootable devices connected to your POC 120 i e MSATASSD USB flash disk USB DVD drive you may need to select one of them as the first boot device There are two ways to select the device You can either press F12 when system boots up to go to Boot Manager and
19. commended driver installation sequence is 1 Chipset driver x Driver_Pool Chipset_Vlv Win7_8 ALL SetupChipset exe 2 Graphics driver x Driver_Pool Graphics_Vilv_EMGD Win7_32 Setup exe 3 Audio driver x Driver_Pool Audio ALC262 Win7_8 ALL Setup exe 4 LAN driver xADriver PooAGbE 1210Win7 8 32 APPS PROSETDX Win32 DxSetup exe USB 3 0 driver x USB3_VIv Win7_ALL Setup exe 6 TXE driver xADriver PooNTXE VlvWin7 8 ALL NSetupT XE exe Windows 7 64 bit The recommended driver installation sequence is 1 Chipset driver x Driver_Pool Chipset_Vlv Win7_8 ALL SetupChipset exe 2 Graphics driver x Driver_Pool Graphics_Vilv_EMGD Win7_64 Setup exe 3 Audio driver x Driver_Pool Audio_ ALC262 Win7_8 ALL Setup exe 4 LAN driver xADriver PooAGbE 1210Win7 8 64 APPS PROSETDX Winx64 DxSetup exe USB 3 0 driver x Driver_Pool USB3_Vlv Win7_ALL Setup exe 6 TXE driver xADriver PooNTXE VlvWin7 8 ALL NSetupT XE exe Windows 8 8 1 32 bit The recommended driver installation sequence is 1 Chipset driver xADriver Pool Chipset VIvWin7 8 ALL SetupChipset exe 2 Graphics driver xADriver PoolGraphics 3rd i7 VIvWin7 8 32 Setup exe 3 Audio driver x Driver_Pool Audio ALC262Win7 8 ALL NSetup exe 4 LAN driver xADriver PooAGbE 1210 Win7 8 32 APPS PROSETDX Win32 DxSetup exe 5 TXE driver xADriver PooNTXE VlvWin7 8 ALL NSetupT XE exe Windows 8 8 1 64 bit The recommended driver installation sequence is 1 Chipset driver xADriver Pool Chipse
20. driver installation 2 2 VGA Connector n PWR WDT HDD B ony I J POC 120 series features VGA output which is directly driven by integrated Intel HD Graphics engine and supports up to 2560 x 1600 resolution By BIOS default and hardware implementation the VGA output is always enabled in any case To achieve best VGA output resolution in Windows you need to install corresponding graphics driver Please refer to section 4 3 for information of driver installation pen Copyright 2015 Neousys Technology Inc All Right Reserved Page 13 of 53 POC 120 Series User s Manual 2 3 Back Panel I O Functions To fit more general application requirements POC 120 series offers more I O functions on its back panel In this section we ll illustrate each I O function on the back panel 2 3 1 USB3 0 Connectors There are totally one USB 3 0 port and two USB 2 0 ports on POC 120 series The USB 3 0 port is located on the back panel This USB 3 0 port is implemented via native xHCI controller inside Bay Trail SoC By BIOS default this USB port is operated in xHCI eXtensible Host Control Interface mode and is compatible to USB 3 0 USB 2 0 USB 1 1 and USB 1 0 devices To utilize USB 3 0 function in Windows you need to install corresponding USB 3 0 driver for Bay Trail SoC Please refer to section 4 3 for information of driver installation 2 3 2 USB2 0 Connectors In addition to the USB 3 0 ports POC 120 series provides an
21. ector 2 Connect the latched switch to the pin 1 and pin 2 of the on board 1x3 pins 2 0mm pitch pin header polarity is negligible DRE 2E MSS vas ort aai nd ddl adl dallas a Sa ats 3 When the latched switch is closed the DC power is break off and system is turn off When the latched switch is opened the DC power is feed in and with the correct setting of Power On after Power Failure BIOS option please refer to section 4 1 6 the system is turn on 3 6 3 To Power on POC 120 Using an Non latched Switch ATX mode For an application which places POC 120 inside a cabinet it s useful to control the on off of the system using an external switch POC 120 series provides an on board 3 pin wafer connector for detail please refer to section 2 4 1 for connecting a latched non latched switch and behaves either AT mode or ATX mode power on off control When using the AT X mode on off control you need a non latch switch The external non latched switch acts exactly the same as the power button on the front panel To power on POC 120 using an external non latched switch ATX mode please follow the steps Copyright 2015 Neousys Technology Inc All Right Reserved Page 32 of 53 POC 120 Series User s Manual listed below 1 Prepare a non latched switch with a 2 pin 2 0mm pitch connector 2 Connect the non latched switch to the pin 2 and pin 3 of the on board 1x3 pins TTT Sas 8 68 25 tf ga a
22. eyboard mouse in DOS environment PWR WDT HDD RESET o o o J ae tote Copyright 2015 Neousys Technology Inc All Right Reserved Page 11 of 53 POC 120 Series User s Manual 2 2 5 Speaker out Jack kc 14 PWR WDT HDD RESET VGA o oo usB2 g TC POC 120 series provides speaker out function using Intel High Definition Audio built in in Bay Trail SoC and Realtek ALC262 codec An audio jack is located on the front panel To utilize the speaker out function in Windows you need to install corresponding drivers for both Intel ICH8 M chipset and Realtek ALC262 codec Please refer to section 4 3 for information of driver installation 2 2 6 Gigabit Ethernet Ports POC 120 series offers two Gigabit Ethernet ports using Intel 1210 GbE controller When plugging in the Ethernet cable you can tell the Ethernet status and speed from the LED indicators on the RJ45 connector as following Active Link LED Yellow Ethernet port is disconnected Ethernet port is connected and no data transmission Ethernet port is connected and data is transmitting receiving Speed LED LED Color Green or 10 Mbps Orange 100 Mbps 1000 Mbps L PRO nn Copyright 2015 Neousys Technology Inc All Right Reserved Page 12 of 53 POC 120 Series User s Manual To utilize the GbE port in Windows you need to install corresponding driver for Intel 1210 GbE controller Please refer to section 4 3 for information of
23. hee ES a POC 120 Series User s Manual Neousys Technology Inc POC 120 Series Ultra compact Atom Bay Trail l Fanless General Purpose Embedded Controller User s Manual Rev A1 Published May 29 2015 Copyright 2015 Neousys Technology Inc All Right Reserved Page 1 of 53 POC 120 Series User s Manual 2015 05 29 First formal release Wen mom Copyright 2015 Neousys Technology Inc All Right Reserved Page 2 of 53 POC 120 Series User s Manual Contents Belg ae ee te er 5 Declaration O i 7e 4 0 400 m 5 E E 5 vc YOE 5 Copyright and Trademarks anen 5 Chapter 1 Introduction ccnn 6 ESE E EE E E E TEE 6 ke wel e 6 es 61 16 1 6721 0 n REM 7 Chapter 2 Knowing your POGC T120 iussescsskieterugnetite m Moa qtustet etate ttam Sp YR RH MSIE oe DESEE 9 2 1 SIMO ACHING YOU T OO T eserinin ar Vt EUH eames ene ese veneni 9 2 2 Front Panel 1 0 Functions eee eee en 10 ZN OWN BONON etnine esana RUD AIA AEA EO ERN A AoA RUM CU le sens eons 10 2 22 TOSS BULITOD en ene ne tenn te ee eee NM ee ee 10 2 2 9 LED NndicatorS ordre ttai rates n E Pu deett e gt 11 22A USB 20 COnNNEClO isser iennet ai ERARE Enana 11 PO A OE AG Tem 12 2 2 6 Gigabit Ethernet POS eones E 12 2 2 7 V GACONNGCIO eee en enn TAR a ee 13 2 3 Back Panel TO FunctionS rereana AEAEE EEEE EEEE beta itia rene Ree oat pt 14 2 TY B OOOO
24. is POC Series WDT amp DIO Library Setup Wizard This will install Neousys Nuvo Nuvis POC Series WDT amp DIO Library version Ver 2 00 on your computer It is recommended that you close all other applications before continuing Click Next to continue or Cancel to exit Setup am rini Copyright 2015 Neousys Technology Inc All Right Reserved Page 49 of 53 POC 120 Series User s Manual 2 Click Next gt and specify the directory of installing related files The default directory is C Neousys WDT_DIO Select Destination Location Where should Neousys Nuvo Nuvis POC Series WDT amp DIO Library be installed k Setup will install Neousys Nuvo Nuvis POC Series WDT amp DIO Library into the following folder To continue click Next If you would like to select a different folder click Browse C Neousys WDT_DIO Browse At least 1 3 MB of free disk space is required SS 3 Once the installation is finished a dialog appears to prompt you to reboot the system The WDT amp DIO library will take effect after system rebooting Completing the Neousys Nuvo Nuvis POC Series WDT amp DIO Library Setup Wizard To complete the installation of Neousys Nuvo Nuvis POC Series WDT amp DIO Library Setup must restart your computer Would you like to restart now 2 No I will restart the computer later Finish L TERASON Copyright 2015 Neousys Technology Inc All Right Reserved
25. n of terminal block gives an easy and reliable way for wiring the DC power The following table describes the pin definition of the terminal block For detail information of connecting DC power please refer to section 3 5 Pin Description Positive polarity of DC power input 8 35V Negative polarity of DC power input usually power ground Note 1 Thespring clamp terminal block accepts wires of gauge 16 24 AWG and stripping length of 8 mm Please always use wires with correct gauge stripping length to ensure reliable DC power wiring 2 Please make sure the voltage and polarity of DC power is correct before you connect it to POC 120 Supplying a voltage over 35V will damage the system LU Copyright 2015 Neousys Technology Inc All Right Reserved Page 16 of 53 POC 120 Series User s Manual 2 4 Internal I O Functions 2 4 1 Remote On Off Control L919 919 aj le e 4 TES N ma 1 ces The remote on off control function allows users to turn on or turn off the system remotely by connecting an external switch This function is provided via a 1x3 pins 2 0mm pitch pin header on the PCBA Both AT mode and AT X mode on off control are supported For detail information of using remote on off control function please refer to section 3 6 2 3 6 3 Switch Connection for AT ATX Mode Remote On Off Control y ee a e Copyright 2015 Neousys Technology Inc All Right Reserved Page 17 of 53 POC 120 Series U
26. o edit change BIOS options insyde Press F2 go to Setup Utility Press F12 go to Boot Hanager Wo Copyright 2015 Neousys Technology Inc All Right Reserved Page 37 of 53 POC 120 Series User s Manual 4 1 1 COM1 Operation Mode COM1 of POC 120 series supports RS 232 full duplex RS 422 full duplex and RS 485 half duplex mode You can set the COM1 operating mode via BIOS settings Another option in BIOS called Slew Rate defines how sharp the rising falling edge is for the output signal of COM1 For long distance RS 422 485 transmission you may set the Slew Hate option as High to improve signal integrity For RS 422 485 communication the RS 422 485 Termination option determines whether to enable disable internal termination of RS 422 485 transceiver according to your wiring configuration e g with or without external termination To set COM1 operating mode 1 When POC 120 boots up press F2 to enter BIOS setup utility 2 Goto Advanced Peripheral Configuration 3 Set the Set COMI as option to a proper mode for COM1 of your POC 120 Set COM as RS 232 4 1 2 USB xHCI Mode Configuration POC 120 offers one USB 3 0 and two USB 2 0 port via its native XHCI EHCI controller Legacy USB support is implemented so you use USB keyboard mouse in legacy environment e g DOS Due to the nature that xHCI is not natively supported in some operating systems we suggest to disable the xHCI mode
27. of Conformity FCC This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE The product s described in this manual complies with all applicable European Union CE directives if it has a CE marking For computer systems to remain CE compliant only CE compliant parts may be used Maintaining CE compliance also requires proper cable and cabling techniques Copyright and Trademarks This document contains proprietary information protected by copyright All rights are reserved No part of this document may be reproduced by any mechanical electronic or other means in any form without prior written permission of the manufacturer Company product names mentioned herein are used for identification purposes only and are trademarks and or registered trademarks of their respective companies EDU Copyright 2015 Neousys Technology Inc All Right Reser
28. other USB 2 0 port on its back panel By BIOS default this USB 2 0 ports is operated in EHCI Enhanced Host Control Interface mode and are compatible with USB 2 0 USB 1 1 and USB 1 0 devices Legacy USB support is provided so you can use USB keyboard mouse in DOS environment L ooe Copyright 2015 Neousys Technology Inc All Right Reserved Page 14 of 53 POC 120 Series User s Manual 2 3 3 COM Ports POC 120 provides two COM ports via two 9 pin D Sub male connectors on the back panel for communicating with external devices They are implemented using industrial grade ITE8783 Super IO chip 40 to 85 C and provide up to 115200 bps baud rate COM is a BIOS configurable RS 232 422 485 port and COM2 supports RS 232 only The operation mode of COM1 can be set in BIOS setup utility refer to section 4 1 1 for detail The following table describes the pin definition of COM ports RS 485 Mod RS 232 Mode RS 422 Mode ceed RS 232 Mode Two wire 485 wo BD TX 4mMR TX Dm aes OUR ose 1 Dh ms NS m a EJ E o2 3 a 5 6 8 9 J Lo Copyright 2015 Neousys Technology Inc All Right Reserved Page 15 of 53 POC 120 Series User s Manual 2 3 4 2 Pin Spring Clamp Terminal Block for DC Input POC 120 series features a spring clamp terminal block for direct DC wiring It accepts a wide range of DC power input from 8 to 35V And the spring clamping connectio
29. ser s Manual 2 4 2 mSATA Connector ETES eT A POC 120 odit a mSATA port to accommodate mSATA flash disk module mSATA is a solid state storage device with SATA interface and is very reliable for harsh environments with intense vibration shock The system recognizes mSATA as a native storage device and accordingly you can install any operating system in the mSATA module such as Windows 7 Windows 8 Linux and etc 2 4 3 DDR3L SODIMM Socket POC 120 series provides one 204 pin SODIMM socket for memory installation It supports a maximal 8GB capacity by installing one low voltage 1 35V DDR3L 1333 SODIMM modules For information of installing DDR3L memory modules please refer to section 3 2 for detail J Pie Piet Copyright 2015 Neousys Technology Inc All Right Reserved Page 18 of 53 Mer esi POC 120 Series User s Manual Note Please make sure you re installing a 1 35V DDR3L SODIMM module to POC 120 Installing a 1 5V DDR3 SODIMM will cause system failed to boot LM Copyright 2015 Neousys Technology Inc All Right Reserved Page 19 of 53 POC 120 Series User s Manual 2 5 POC 120 Mechanical Dimension 2 5 1 Top View 122 60 L etn nts Copyright 2015 Neousys Technology Inc All Right Reserved Page 20 of 53 POC 120 Series User s Manual 2 5 2 Front View dJ ZO 35 70 az LE Copyright 2015 Neousys Technology Inc All Right Reserved Page 21 of 53 POC 120 Series
30. sting criteria please contact Neousys Technology For sub zero operating temperature wide temperature DDR3 L and wide temperature mSATA module are required a a Copyright 2015 Neousys Technology Inc All Right Reserved Page 8 of 53 POC 120 Series User s Manual Chapter 2 Knowing your POC 120 2 1 Unpacking your POC 120 When you receive the package of POC 120 series please check immediately if the package contains all the items listed in the following table If any item is missing or damaged please contact your local dealer or Neousys Technology Inc for further assistance POC 120 ultra compact fanless controller According to the configuration you order your POC 120 may contain DDR3L or mSATA module Please verify these items if necessary Neousys Drivers amp Utilities DVD L ee Copyright 2015 Neousys Technology Inc All Right Reserved Page 9 of 53 POC 120 Series User s Manual 2 2 Front Panel I O Functions On POC 120 series we design general purpose I O functions on the front panel so you can easily access them In this section we ll illustrate each I O function on the front panel 2 2 1 Power Button kc PWR WDT HDD RESET o o o USB2 0 e The power button is a non latched switch for ATX mode on off operation To turn on the POC 120 press the power button and the PWR LED on the center top side is lighted up To turn off the POC 120 you can either issue a shutdown command in OS
31. t VIvWin7 8 ALL SetupChipset exe 2 Graphics driver xADriver PoolGraphics 3rd i7 VIvWin7 8 64 Setup exe ee Copyright 2015 Neousys Technology Inc All Right Reserved Page 47 of 53 POC 120 Series User s Manual 3 Audio driver x Driver_Pool Audio ALC262 Win7_8 ALL Setup exe 4 LAWN driver xADriver PooAGbE 1210Win7 8 64 APPS PROSETDX Winx64 DxSetup exe 5 TXE driver xADriver PooNTXE VIvWWin7 8 ALL NSetupT XE exe y LM Copyright 2015 Neousys Technology Inc All Right Reserved Page 48 of 53 POC 120 Series User s Manual Appendix A Using Watchdog Timer POC 120 series provides watchdog WDT timer function to ensure reliable system operation WDT is a hardware mechanism to reset the system if the watchdog timer is expired Users can start WDT and keep resetting the timer to make sure the system or program is running flawlessly In this chapter we ll illustrate how to use the WDT DIO function library provided by Neousys to program the WDT and DIO functions Install WDT and DIO Library The WDT DIO function library is delivered in the form of a setup package For POC 120 series please use WDT DIO Setup v2 0 6 exe or later revision In prior to program WDT and DIO on POC 120 series you should execute the setup program and install the library 1 Execute WDT DIO Setup exe The following dialog appears Setup Neousys Nuvo Nuvis POC Series WDT amp DIO Library lo s exem Welcome to the Neousys Nuvo Nuv
32. the Chipset SATA Mode option to a proper mode for your POC 120 WE nal Copyright 2015 Neousys Technology Inc All Right Reserved Page 39 of 53 POC 120 Series User s Manual Chipset SATA Mode lt AHC I gt N 4 1 4 C States and Max C States C States is a power saving technique implemented in modern Intel processors It shuts down clock signals and power for idle logic units inside the CPU to reduce energy consumed The trade off however is a longer latency for CPU to wake up and be 100 operational Depending on your application you can configure these options to have higher performance disable C States or lower power consumption enable C States and set Max C States to C6 C7 To set C States and Enhanced C States 1 When POC 120 boots up press F2 to enter BIOS setup utility 2 Goto Power Advanced CPU Control 3 Enable disable the C States option according to your application 4 Configure the Max C States option according to your application Enabled Enabled i ut Copyright 2015 Neousys Technology Inc All Right Reserved Page 40 of 53 POC 120 Series User s Manual 4 1 5 Wake on LAN Option Wake on LAN WOL is a mechanism which allows you to turn on your POC 120 via Ethernet connection To utilize Wake on LAN function you have to enable this option first in BIOS settings Please refer to section 3 6 4 for instructions of using WOL function To enable disable Wake on L
33. then select one of the devices or select the boot device in BIOS settings To select a boot device in BIOS 1 When POC 120 boots up press F2 to enter BIOS setup utility 2 Goto Boot Boot Device 3 The Boot Menu option determines whether to list all bootable devices connected to your POC 120 according to device or device type The default order of boot device type is e Hard Disk Drive e USB e CD DVD ROM Driver e Floppy Drive e Others You can use F5 F6 or to change the boot order of devices or device types OM Copyright 2015 Neousys Technology Inc All Right Reserved Page 43 of 53 POC 120 Series User s Manual Boot Nau lt By Device gt OLS Copyright 2015 Neousys Technology Inc All Right Reserved Page 44 of 53 POC 120 Series User s Manual 4 2 Operating System Support POC 120 series supports most operating system developed for Intel x86 architecture The following list contains the operating systems which have been tested in Neousys Technology Inc Microsoft Window 7 32 bit Microsoft Window 7 64 bit Microsoft Window 8 8 1 32 bit Microsoft Window 8 8 1 64 bit Ubuntu 14 04 or later version Fedora 20 1 or later version OpenSuSE 13 1 or later version CentOS 7 or later version Neousys will keep this list updated as we continuously test other operating systems with POC 120 series Please contact us for the latest OS support list J EDU Copyright 2015 Neousys Technology Inc
34. ved Page 5 of 53 POC 120 Series User s Manual Chapter 1 Introduction 1 1 Overview Introducing the new member of Neousys ultra compact POC family POC 120 is a low cost entry level embedded controller with yet more compact dimension It further reduces its height to 3 4 cm to have a very low profile chassis for restricted space POC 120 incorporates Intel Atom E3826 dual core processor to deliver adequate computing performance It provides general I O such as Gigabit Ethernet ports COM ports and USB3 USB2 ports for most embedded applications Instead of traditional HDD POC 120 supports mSATA SSD to ensure reliable disk access in harsh environments POC 120 reserves internally a high speed interface for I O expansion By customizing a mezzanine board you can have versatile I O functions This makes POC 120 not only an ultra compact controller but also a tailor made embedded system for your designated application Please contact Neousys for POC 120 OEM ODM projects az pee Copyright 2015 Neousys Technology Inc All Right Reserved Page 6 of 53 POC 120 Series User s Manual 1 2 Product Specification System Core Processor Intel amp Atom E3826 1 46 GHz dual core processor Integrated Intel amp HD Graphics 1x SODIMM socket for DDR3L 1333 up to 8GB Graphics Memory Panel I O Interface Ethernet Video Port 2x Gigabit Ethernet ports by Intel 1210 GbE controller 1x VGA connector for analog RGB

POC-120 User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents