programming keys
Contents
1. VV VV WV Note if you use the K LED keypad once had access to the user menu and selected the second parameter the LED will flash Display the current code one digit at a time by pressing the v until the contemporary switched on of the LEDs 1 3 5 and 7 that identifies the end Now press 6 times the DELETE key in order to clear the current code enter the new personal code 6 digits and confirm with the ATTENTION if you forget a code you cannot resume it and will have to reset the system to its default settings DEFAULT RESET 8 DATE AND TIME The date and time can be set both by the installer through the Technician Menu and by the user through the Users Menu Procedure gt Enter a valid code to open the menu gt Press 4 to select DATE TIME then press to confirm gt As soon as the day of the week starts blinking press the numerical key from 0 to 6 that corresponds to the day of the week you wish to enter 0 Monday 1 Tuesday 6 Sunday gt Use keys f and to move the flashing cursor to the position that corresponds to the parameter you wish to change The sequence is day month year time and minutes To change a parameter delete the current setting by pressing DEU twice and enter the two new digits directly gt After completing the setting operation press to confirm2. System ready for all input at rest Input Door activated Kitchen Window activated Kitchen Window activated Insert to quit I Output User not authorised Output X activated Output Y deactivated Call Queue suspended 3 ARMING THE SYSTEM It is possible to use 2 different arming modes for each area e MANUAL In this mode you can select the area and the program you wish to arm e AUTOMATIC The system automatically arms and disarms depending on the times set on the TIMER The MANUAL arming operations can be performed using keypads plugs The zones configured with ON OFF functions one program per zone only It s possible to arm disarm the system by sending a SMS It s possible to define which program for area arm or disarm The syntax of SMS must be the following UPWD aaaaaa ARM X 12345678 where is the password default 654321 X is the area on which it s possible to act 12345678 is the list of programs to arm it s possible to define 1 or more programs To disarm the system the syntax is DISARM X instead of ARM X By sending a SMS it s possible to change the password with the following sintax UPWD oooooo UPWD nnnnnn where oooooo is the old password and nnnnnn is the new one 31 ARMING THE SYSTEM WITH THE KEYPAD Type the USER code for the area for example 111111 and press to confirm
3. 9 PROGRAMMING KEYS Keys model INS EP or Beatle can be programmed ONLY by users who have a user name These users can create an unlimited number of keys in order to operate the system within the limits permitted to them The installer must instead determine during the programming phase the plug that users may use to program their keys For more information see paragraph CONFIGURING PLUGS Procedure gt Open the USERS Menu by typing directly the user code and confirming it with key gt Press to select PROGRAMMING PLUG Press to confirm gt Press to confirm to cancel the operation gt After you confirm the operation on the programming plug the LEDs start to flash quickly to indicate that the plug is ready to receive a key to program Insert a key into the plug and wait for the LEDs to stop flashing Then extract the programmed key Repeat this procedure to program additional keys v v 10 EXECUTE CALLBACK Note In order to ensure the operation success the user has to warn the installer that he is are doing a CALLBACK so the installer can provide the necessary resources Link pending with the computer Procedura gt Open the USERS Menu by typing directly the user code and confirming it with key 1 gt Press to select EXECUTE CALLBACK Press to confirm gt Press to confirm to cancel the operation gt Once confirmed
4. 2002 95 YOUR SECURITY CHOICE CE AMC CONTROL UNITS Series 8128 840 412 USER MANUAL Version 4 001 1 MENU USER BY KEYPAD PERSONAL CODE USER CODE DEFAULT user 01 111111 Down arrow v Enter s Use the numeric keys to configure the programs to be included from 1 to 8 ARMING gt n Configured Not Configured v y M Use the Up and Down arrow keys to scroll through the list of events READ EVENTS Press enter to exit v M NAME USER 01 gt Use the buttons to change the USERNAME Y CODE USER 01 Use the numeric keys to change the USER CODE Y Enter the day of the week from 0 to 6 from Sun to Sat Moving with the arrow DATE TIME right to enter dd mm yy h min Press ENTER to confirm v Y Vv PROGRAM KEY PROGRAM KEY m CONFIRM END v Y V M EXECUTE CALLBACK EXECUTE CALLBACK CONFIRM END v Y 0 Disabled Set To 1 for PC Connection TELEMNG ON 1 Enabled as 7 v 5 m CREDIT INFO P button X t GSM MANAGEMENT ress DUMON visualize on LCD m m Display SoftWare Y level and GSM level FIRE RESET ASK FOR CREDIT MENU VOICE
5. GUIDE Insert Personal Code followed by the Ash Key Correct Code After the response from the dialer press the pound key to enter the voice menu Personal Code Wrong To finish the call and disconnect from the dialler of the control panel press two times the Ash Key Insert 1 to check the status of the system MH User not authorized Area X System Armed Program Y K Area X System Disarmed Y IM User not authorized Attention Some Zones are not Ready Bathroom Window Insert 1 to deactivate Insert 1 to activate Program 1 Insert 1 to exclude the 2 to ignore nn at 2 to activate Program 2 99 t 9 tivate all P all Kitchen Window BEL I Aa Log ans Insert 1 to deactivate Insert 0 to deactivate the system 3 to ignore 2 to ignore Insert to quit Insert to quit Y I Insert 3 to use Select output net authorized Garden Light i E OES a Insert 1 to activate Garden Light gt activated deactivated q Insert 2 to deactivate Garden Light Bathroom Window deactivated Insert 4 to check the status of the zones User not authorised Insert 5 to check the status of the outputs Insert 6 to suspend the call queue gt
6. Select ARMING and press 4 to confirm Use the numerical keys from 1 to 8 to select the programs you wish to include or exclude for the arming Press to confirm or press cancel to go The system starts to count the output time and then arms The yellow LED flashes during the output time and turns on permanently once the system is armed V v v Vv v v 1 PROGRAMI 2 PROGRAM 3 PRoGRAM3 4 PROGRAM4 5 PROGRAMS 6 PRoGRAM6 8 PROGRAMS Note if there are keypads assigned to several areas press J to select the area in which you wish to perform the arming The operating area is displayed in the lower left of the display 32 ARMING THE SYSTEM WITH EXCLUDED ZONES When you arm the system with open zones the system displays a message prompting the user to confirm before continuing This message specifies how many zones are open 04 ZONES OPEN CONTINUE Press one of the following keys to continue point A 3 POINT A At this point you have three options depending on the key you press Cancels the arming operation and returns to the Users Menu Pal Continues the arming operation all the opened zones will have to be closed before the quit time expires otherwise the system issues an alarm The open zones are excluded from the arming operation canc be excluded from the current arming the desired input
7. cal instructions You can perform the following operations Arm and disarm or more area programs Enable and disable the Open Collector outputs Exclude zones with faults Check the system status in real time To perform all the operations described above you will have to press and then enter your user code followed by at the beginning of the call Note you can work ONLY on the areas and zones that you are enabled to use The opening pages of this manual shows the block diagram of the Voice Guided Menu 5 READING EVENTS When a new event occurs the panel will report it with the red LED lights on the keyboard on the plugs The events memory led will switch off when the system will armed or if you enter the menu READ EVENTS The control unit has a memory of dynamic events that are automatically allocated to the different areas When the event memory is full the system displays a message on the keypad display At this point you have two options e You can save all the events on the PC in several formats e You can allow the new events be overwritten on the new ones Here how to read the EVENTS Procedure gt Open the User menu gt Usekeys and 4 to select MANAGE EVENTS and press to confirm gt Usekeys and 4 to select READ EVENTS and press to confirm gt Press T and 4 to browse
8. ed gt Press to reset Contents MENU USER BY KEYPAD MENU VOICE GUIDE ARMING THE SYSTEM CONTROLLING THE SYSTEM REMOTELY FROM A TOUCH TONE PHONE READING EVENTS ASSIGNING A NAME TO A USER ENTERING A NEW USER CODE DATE AND TIME PROGRAMMING KEYS EXECUTE CALLBACK ENABLING THE REMOTE MANAGEMENT GSM MANAGEMENT FIRE ALARM RESET O O O DH HN Ww N All our products are compliant with the requirements of standard CEI 79 2 second release 1993 The installation must be performed in a workmanlike manner by qualified personnel Elettronica S r l shall not be responsible for damages originating from the tampering of the product by unauthorized people It is advisable to check the correct operation of the alarm system at least once a month It is also important to remember that a reliable electronic alarm system can only limit the risk of intrusions thefts fires or similar events but not eliminate them If you find inconsistencies in the manual immediately contact the Technical Assistance of AMC Elettronica S r l 10
9. nsert or move the key close to a plug enabled to manage the area for which the key is valid gt Wait for the LED of the program you wish to arm to turn on then extract the key Note each plug can be used for one area only and can manage up to 3 programs per area The output time counter starts as soon as you extract the key This condition is signalled by the flashing of the LED that corresponds to the selected arming operation and by a series of BEEPS issued by the keypads and plugs if the sound option is enabled 3 5 meaning of the reader leds e System DISARMED The green control LED turns on if all the zones are idle e System armed The yellow and green LEDs turn on e System in alarm All the LEDs flash e During the quit time Yellow LED flashes Green turn on if all zones are idel e During the key programming All the LEDs quickly turn on in sequence Note if you arming the system with a key and one or more zones are open the system arms and after the quit time the system will go into alarm unless you program the automatic exclusion of the zone s or you disable the arming with key when open zones are present see the relevant paragraphs of Chapter INPUTS MENU 4 CONTROLLING THE SYSTEM REMOTELY FROM A TOUCH TONE PHONE If you have an optional voice synthesis SV S module you can remotely control the system by calling the number of the line to which the system is connected from a touch tone phone and following the vo
10. see below Zone to exclude ZN 01 KITCHEN Heel joo Kee Keypad display Symbol indicates that the zone has been excluded Symbol e indicates that the zone is closed Symbol indicates that the zone is open Use keys and to move the flashing cursor to the position that corresponds to the desired zone Press DEL to excluded or include the desired zones Press to confirm the selection or 0 to exit from the menu Note the green control LED will not turn on for the excluded zones It s also possible to decide to exclude some zones when you arm the system After confirming the item ARMING and have decided which partial insert type button 9 The display will highlight all the affected zones and proceeding as described above in POINT A will be possible to decide which zones to exclude 33 QUICK ARMING You can select from the Technician Menu an option that enables you to quickly arm the system without using the user code in arming mode ONLY Procedure Press and select the partial that you want using the numeric keypad gt Press to confirm NOTE if you select this operation you will have to enter a valid user code in order to disarm the system 3 4 ARMING THE SYSTEM WITH AN ELECTRONIC KEY The system can also be armed and disarmed using programmed keys Procedure gt I
11. the command the system will call the computer of the installer by telephone the installer will take the actions required Press the key to exit the menu CALLBACK v 11 ENABLING THE REMOTE MANAGEMENT The user is able to enable the installer to connect his the computer to the system either locally by the cable or remotely over phone lines Note if this feature is disabled the installer has no means of connecting with the panel Procedure gt Open the USERS Menu by typing directly the user code and confirming it with key gt Press to select TELEMNG ON parameter 3 on K Led Press to confirm gt Type 1 to enable the function type cancel X to disable it parameter 0 gt Press to confirm 12 GSM MANAGEMENT In this menu you can get information on available Credit Procedure gt Open the USER Menu by typing directly the user code and confirming it with key Press to select GSM MANAGEMENT Press to confirm Open the CREDIT INFO Menu to know the value of the residual credit Open the ASK FOR CREDIT Menu to make a new request for residual credit v v v 13 FIRE ALARM RESET In case of alarm fire the user has the ability to reset the output used as fire alarm Procedure L gt Open the USERS Menu by typing directly the user code and confirming it with key gt Press to select FIRE RESET parameter 4 on K L
12. the list of events gt Press to cancel the events reading operation 6 ASSIGNING A NAME TO A USER You can change the default NAME assigned to each user USERO1 USERO2 etc by entering new name with a maximum length of 16 characters This operation can be performed both by the technician for all users and by the user to whom the name belongs Procedure gt Open the User Menu gt Usekeys and 4 to select USERS NAME and press to confirm gt The upper row of the screen displays the user code and name while the lower one shows the default user name that has to be changed with the cursor blinking on the first character gt Use the alphanumerical keypad to change the character and keys to move the blinking cursor to the left or right Use key DEL to delete a character or enter a blank space between two characters Press to confirm 7 ENTERING A NEW USER CODE Each user is able to change his code Procedure Open the Menu Use keys and to select CODE USERXX parameter 2 on K Led and press to confirm The top line of the display will show the name of the user the bottom line the code to be edited with the cursor flashing on the first issue Use the numeric keys to change the number use the cancel button X to delete an existing number Press to confirm
Download Pdf Manuals
Related Search