moving head fl moving head fl-300 beam 300 beam - Flash
Contents
1. It must be ensured that an expert inspects the mechanical installation and the installation of relevance to safety within the framework of an acceptance test at least every four years The installation fixture must be as such that it can withstand for a period of 60 minutes 10 times the load capacity without harmful deformation It is prohibited for any individual to unnecessarily stay or pass beneath the installation during any type of assembly work The light effect unit must be secured by safety arrested cable if fly mounted The cable must withstand 12 times the weight of the light effect unit Use arrester cables equipped with quick closing links The dropping distance must not exceed 20cm Defect arrester cables or arrester cables that have already been exposed to stress must not be used 6 Operation Controls www flash butrym pl Page 4 Link all DMX devices with a DMX 512 controller by using a standard 3 pin DMX cable Connect the output of the first device with the input of the second device and the output of the second device with the input of the third device and so on Connect the mains plug to an outlet and switch the device on Operating the product for the first time may generate smoke and odor this is not a defect Avoid dis connecting the product repeatedly and quickly from with mains Always wait 15 minutes prior to the next dis connection The device starts not until a self testing and starting time If the moving2. other items in the housing is exempt from warranty 4 Operating Environment The product must be operated and stored in a dry environment only Splash water rain humidity fog may reduce the protective insulation which may lead to fatal electric shocks The limit value for relative humidity is 50 at 45 C A minimum distance of 1 5m to a fog machine must be observed fog saturation in the room must not reduce the visibility to below 10m www flash butrym pl Page 3 The product must be operated at a temperature range of between 5 C and 45 C only Protect the product against direct exposure to sunlight or other heat such as from radiators If the product is taken from a cold environment into a warm environment it must only be taken into operation once it has reached ambient temperature since the condensation created by the difference in temperature may destroy the device Protect the product against dust Dust may reduce the protective insulation which may cause fatal electric shocks The product must be operated at altitudes ranging between 20m below and 3000m above sea level only The product must not be operated during thunder storms risk of destruction from surge voltages The product must be operated at a minimum distance of 1 5m to lit objects only 5 Installation This product can be operated suspended or as a stand alone system Should your lighting effect show any signs of damage do not install the device In this ca
3. Shutter off when color wheel changing 30 39 No function 40 49 Shutter off when PAN and TILT movement and color changing 50 199 No function 200 209 Lamp off after 5S www flash butrym pl Page 5 210 219 Lamp on after 5S 220 255 No function 7 Color wheel 0 9 White 10 19 Color 1 20 29 Color 2 30 39 Color 3 40 49 Color 4 50 59 Color 5 60 69 Color 6 70 79 Color 7 80 89 Color 8 90 199 White 1x8 color mixing effect 200 225 Color wheel anti clockwise rotation from fast to slow rainbow effect 226 229 Stop no function 230 255 Color wheel clockwise rotation from slow to fast rainbow effect 8 Rotating gobo wheel 0 9 Blank 10 19 Gobo 1 20 29 Gobo 2 30 39 Gobo 3 40 49 Gobo 4 50 59 Gobo 5 60 69 Gobo 6 70 79 Gobo 7 80 99 Gobo 7 shaking from slow to fast 100 119 Gobo 6 shaking from slow to fast 120 139 Gobo 5 shaking from slow to fast 140 159 Gobo 4 shaking from slow to fast 160 179 Gobo 3 shaking from slow to fast 180 199 Gobo 2 shaking from slow to fast 200 219 Gobo 1 shaking from slow to fast 220 239 White shaking 240 255 Gobo wheel clockwise rotation from slow to fast flow effect 9 Fog len 0 255 Fog len 10 Reset 0 199 No function 200 209 Reset after 5S 210 255 No function 11 Fine PAN movement 0 255 16 bit PAN movement 12 Fine TILT movement 0 255 16 bit TILT move
4. head is ready to start push and roll the function wheel The LCD display shows the options as below Menu settings DP DN disabled the fixture has 12 channels now eg Lamp mode N lamp on F lamp off Reset system N reset the lighting F stay same Display language Back time yes 0 30S NO INV display N or F exit submenu 0 Control Ctrl sel DMX music AUTO slave AUTO program 0 15 AUTO speed 9set running speed for program Exit submenu Information model ver SN CPU freq year time exit sub menu DMX Addr set address PAN reverse N reversed F normal TILT reverse N reversed F normal P T speed from 00 15 to set the speed for PAN TILT movement P T mode 8bit 16bit when set as 8bit the channels PAN fine and TILT fine will be 11 Motor adjust 01 pan 02 tilt 03 strobe 04 prism 05 exit submenu 12 Exit submenu DMX Protocol Channel Feature Value Effect 1 PAN Movement 0 255 0 540 PAN movement 2 TILT Movement 0 255 0 280 TILT movement 3 PAN TILT speed 0 255 PAN TILT speed from fast to slow 4 Strobe 0 19 No function 20 39 Open 40 89 Strobe from slow to fast 90 139 Strobe effect open increasing 140 189 Strobe effect close decreasing 190 239 Random strobe from slow to fast 240 255 Open 5 Dimming 0 255 0 100 dimming 6 Shutter reset lamp 0 9 No function on off 10 19 Shutter off when PAN and TILT movement 20 29
5. MOVING HEAD FL 300 BEAM USER MANUAL Congratulations on purchasing this FL 300 B www flash butrym pl Page 1 For reasons of safety and approval CE the personal reconstruction and or modification of this product is prohibited Please observe that damage caused by modifications performed manually to this device is not covered by the warranty This product leaves our works in a perfect condition Please observe all notes in these operating instructions to warrant this condition and the safe operation of the product Any damage caused as a result of the non compliance with these operating instructions leads to the expiration of any warranty claim The manufacturer does not accept liability for any damage to property or for personal injury resulting from the improper handling of the product or non observance of the operating instructions Store these operating instructions in a safe place for later reference and pass them to any new holder when selling or lending or leaving this device in the hands of any other party Application According to Purpose This product is a lighting effect which creates special light effects with one lamp To generate these effects the product must be connected to mains and a DMX 512 compatible controller This product is designed for 230V 50Hz A C operation and exclusively for indoor use If used for any purpose other than described in these operating instructions the device may suffer damage and the warra
6. ment 7 Lamps During operation the lamps will reach temperatures of up to 200 C Touching the lamps may cause serious burns Objects coming into contact with the lamps during and shortly after operation may catch fire Disconnect the product from mains prior to installing or before changing a lamp Allow a lamp to cool for approx 15 minutes before exchanging it www flash butrym pl Page 6 Never touch a lamp with bare hands If damaged or deformed a lamp must be exchanged When exchanging the lamp be sure to use suitable lamps only Lamps with greater performance generate excessive heat for the product risk of fire Damage resulting from the use of an unsuitable lamp is exempt from warranty Replace a lamp by unscrewing the fixing screws in top of the bulb compartment Then you open the housing Remove the lamp by pulling it carefully out of the socket Install a lamp by putting it into the socket until it meets a resistance Do not use any force this could cause serious damage to the socket as well as the lamp Close the compartment and tighten the screws 8 Fuse Disconnect the product from the mains before changing a fuse Only replace the fuse by a fuse of the same type and rating An incorrect fuse could damage or destruct the lighting effect Replace a fuse by levering the fuse holder cover with an appropriate screwdriver Remove the old fuse and place the fuse inside the holder Replace the fuse holder and insert i
7. nty expires Also any other use is linked with risks such as short circuits fire electrical shock etc Notes on Safety 1 Before Operation Prior to the initial operation of this product please do the followings e Read these operating instructions with great care e Study and observe all instructions carefully e Ensure that everybody and anybody involved in the installation operation transport and storage of this product is suitably qualified e Verify whether any visible damage was caused during transport If the power cord housing or the light are damaged do not operate the device contact your specialized dealer immediately 2 Supply Voltage Mains Cord and Connection to Mains The handling of supply voltage mains cords and connections to mains calls for particular care considering the risk from a life threatening electric shock the risk of fire and the risk of short circuits Please observe the following notes in particular Products operating on supply voltage should be kept out of the reach of children Therefore ensure the permanent supervision if children are in the immediate vicinity of the product For commercial facilities the regulations on the prevention of accidents of the respective trade association must be observed The operation of this equipment at schools training facilities and hobby or self help workshops must be supervised responsibly by trained personnel www flash butrym pl Page 2 Check the
8. on transport and when storing the product that no shocks or other forces impact the housing The housing must not touch onto any other devices or objects during operation Easily flammable materials e g decoration material and other surfaces and objects must maintain a minimum distance of 3m to the housing Walls must maintain a minimum distance of 50cm to the housing The device must be installed on a fireproof surface only no carpet Always ensure a proper circulation of air Do not touch the housing during operation it will heat up The housing is safe to touch approx 5 minutes following the end of operation The device must never be carried via the projector arms Use the carrying handles only Fluids must not enter the housing as this could reduce the protective insulation and may trigger short circuits which may lead to fatal electric shocks If fluids have entered disconnect the mains plug immediately and secure the product against unintentional operation and contact your specialized dealer Damage caused as a result of fluids entering the housing is exempt from warranty No metal parts or other items must enter the housing as this may reduce the protective insulation or trigger short circuits which may lead to fatal electric shocks If metal parts or other items have entered disconnect the mains plug immediately secure the product against unintentional operation and contact your specialized dealer Damage caused by metal parts or
9. product regularly for any damage to the mains cord Should you discovery any damage to the mains cord do not operate or disconnect this product Secure the product against accidental operation and contact your specialized dealer Always separate the product from mains by holding the mains plug by the handling surface Never disconnect by holding the line cord Be sure to connect the product exclusively to 230V 50Hz A C Always ensure during installation operation transport and when storing the product that the mains cord is not exposed to possible mechanical damage or damage caused by humidity fluids heat or cold The product s cable entry must not be exposed to stress from pull Create the mains connection once the product has been installed only Always connect the mains plug last The product must only be connected to a proper outlet of the public supply grid Connect the mains cord to suitable outlets only Use extensions cords in compliance with specifications only Do not allow the mains cord to come into contact with other cords Ensure during installation operation transport and storage that none of the cables are freely exposed Never touch the mains cord mains plug and outlets with wet or damp hands When not using the product and prior to cleaning always disconnect the product from mains To do so hold the mains plug by the handing surface and never pull the mains cord 3 Housing Always ensure during installation operati
10. se have your lighting effect repaired by your specialized dealer The manufacturer does not accept responsibility or liability for damage to property or personal injury resulting from an improperly installation As a stand alone system the device must be installed vertically on an absolute planar firm fireproof shock and vibration free surface The installation of this lighting effect must be carried out by trained and professional staff The installation of this lighting must only be carried out with the appropriate materials The suspended installation of this lighting effect necessitates a suitable suspension system The lighting effect must never be fixed swinging freely in the room No individuals should linger underneath the lighting effect during suspended installation It is a must to install this device with a second independent fixture Such second fixture must guarantee in the event of failure of the main fixture that no assembly parts will fall down Use the fixture on the undersurface only The light effect unit must be attached via two certified hooks and omega bracket to a tie bar system Use the screw threads on the undersurface only It must be ensured that an expert inspects the mechanical and _ safety relevant installation prior to the initial operation and following major modifications prior to the renewed operation It must be ensured that an expert inspects the mechanical and safety relevant installation at least once a year
11. t 9 Cleaning The product must be freed regularly from dust other deposits and contamination as this may reduce the protective insulation which may lead to a fatal electric shock Before cleaning always disconnect the product from mains The product should be cleaned with a moist cloth only never use aggressive cleaning agents solvents or benzene for cleaning Ensure that the product is completely dry before operating it again after cleaning 10 Transport To avoid damage caused during transport wrap the product in its orginal packaging only and handle it with great care during transport Technical information Voltage 230V AC 50Hz Total connected load 700W Lamp 1x 300W GY 9 5 discharge lamp Dimensions 470x446x650mm Weight 30kg Please note All information is subject to change without prior notice www flash butrym pl Page 7
Download Pdf Manuals
Related Search