Home

DS-1000 I-V CURVE TRACER User Manual

1. Internal command line buffer overflow Total number of characters in command line cannot exceed 255 ERROR 15 COMMAND LINE OVERFLOW A command has been sent to the DS Tracer before the previous command has finished Wait for return prompt ERROR 16 PARAMETER TOO LONG The maximum length of any command line parameter is 15 characters ERROR 17 TOO MANY PARAMETERS A maximum of 16 parameters including command code are allowed ERROR 30 OVER MAXIMUM VOLTAGE The take I V curve command cannot continue because the PV system voltage exceeds the maximum voltage range this PV system cannot be tested with the DS Tracer ERROR 32 INPUT LESS THAN OR EQUAL ZERO VOLTS The take I V curve command cannot continue because the PV system voltage is less than or equal to 0 V Check PV system and DS Tracer disconnect switches This error can also be caused by a reverse polarity on the DS Tracer to PV system connection page A32 Error Codes DS 1000 Operating Manual ERROR 50 INVALID NUMERIC PARAMETER Parameter must represent valid numeric value ERROR UNKNOWN ERROR Some type of unknown error has occurred Check parameters for proper syntax DS 1000 Operating Manual DS 1000 USB Drivers page B33 Appendix B DS 1000 USB Drivers In order to use the DS 1000 USB port for tracer control the DS 1000 USB drivers must be installed on the computer running IVPC Two drivers will be installed The pri
2. 0 4 V 4 V 0 05 0 2 30 mV 100 V 40 MV 50 MV 0 01 0 1 40 MV 80 MV 0 05 0 2 3 mV 10V 4 mV 17 mV 0 01 0 1 7 mV 50 mV 0 15 0 4 300 uV PV Current Accurac Range Error 25 C Error 0 50 C Resolution 100A 50 MA 50 mA 0 05 0 2 50 MA 50 mA x 0 1 0 2 3 mA 10A 5 5 0 05 0 2 5 50 MA 0 2 0 4 300 uA 1A 0 5 mA 0 5 mA 0 07 0 2 0 5 mA 0 5 MA 0 35 0 9 30 uA Irradiance and Aux Input Accurac Range Error 25 C Error 0 50 C Resolution 5V 500 uV 550 uV 0 01 0 015 500 uV 800 uV 0 05 0 1 150 uV 500 mV 50 uV 60 uV x 0 01 0 02 50 uV 120 uV 0 05 0 1 15 UV 50 mV 5 UV 10 uV 0 01 0 02 5 UV 70 UV 0 05 0 1 1 5 UV 5 mV 0 5 uV 5 uV 0 03 0 05 1 1 uV 60 uV 0 05 0 1 0 15 uV Temperature Accurac Error 25 C Error 0 50 C 1 2 5 max Does not include error of attached thermocouple page C36 Technical Specification DS 1000 Operating Manual General Specifications Power 85 Vac to 264 Vac 50 60 Hz Battery 5 A Hr sealed lead acid EnerSys 20809 0020 Hours of Use Up to 12 Hrs on full battery charge Charge Time Less than 8 hours Size 46 cm x 36 cm x 20 cm 18 x 14 x 8 Weight 14 4 kg 31 8 Ibs
3. PV short circuit current exceeds selected current range check current range setting Check for bad connections to PV module or array l V looks abnormal PV system is malfunctioning PV system is NOT isolated from power conditioning or other equipment Voltage sense wires on test lead are broken near clips DS Tracer Stops Working Locks Up Battery out of power charge battery Unknown Reasons reset DS Tracer by recycling power Cannot establish connection of external computer to DS Tracer DS Tracer is not turned on or has turned itself off DS Tracer RS 232 or USB port is not connected to computer IVPC is set to wrong COM port DS Tracer will not accept external command Parameters are not properly formatted Irradiance readings are incorrect Pyranometer coefficients are incorrect Supplied signal is not a DC voltage Aux input readings are incorrect Supplied signal is not a DC voltage Differential input signals is not referenced to input common DS 1000 Operating Manual Error Codes page A31 Appendix A DS Tracer ERROR CODES ERROR 10 I O ERROR RS 232 serial communications error Baud rate parity number of data bits or number of stop bits is incorrect DS Tracer uses 9600 baud no parity 8 data bits and 1 stop bit ERROR 13 UNKNOWN COMMAND Command is not recognized by the DS Tracer This may be due to a syntax error ERROR 14 BUFFER OVERFLOW
4. fuse should only blow if a DC source voltage exceeds the rating on the DS Tracer panel Replace only with a 2 Amp fast blow DC charging fuse There is an internal fuse on the power supply board battery circuit This fuse is installed as protection when the DS Tracer is removed from its case during repairs page 26 Pre Charge Precautions DS 1000 Operating Manual 5 0 Pre Charge Precautions In order to compensate for voltage drops across the test lead the DS Tracer pre charges the capacitive load to approximately 15 V When an I V curve is taken the PV module voltage starts at 15 V and increase to Voc Most PV modules single crystal silicon for example easily withstand this negative pre charge voltage However this pre charge voltage can damage some thin film modules particularly those with very low Voc values Higher voltage modules have more cells in series and therefore the pre charge voltage is spread across more cells Only individual low voltage thin film modules are affected It is not a concern for systems with many modules in series Avoid damage to a thin film module by inserting a by pass diode across the module terminals as shown in Figure 9 This diode limits the reverse voltage to approximately 1 V maximum Locating the diode at the PV module terminals still allows the pre charge to offset voltage drops across the test leads System Disconnect Switch Test Lead PV Array Figure 9 Use of
5. ACME Curves ivd Sex File Edit Curve View Format Settings Tabs Window New 3 Open save Print Curve 45 Quick Curve 8 Normalize Normalization Pyra 1 None Pyra2 None AutoFill ACME Curves ivd MultiCurve 1 Curve 2 Peak Power 5 186 Fil Factor 2 08 x 291 73 Voc V 356 92 Untied _ v Ipeak 4 17 776 Isc 4 19 350 Name ACME Solar Site Far ide Sub System Section 3 Module od 1 8 Misc Operational Test Irrad 1 w m2 1 035 Irrad 2 w m2 831 Temp 1 45 3 Press Take Curve Alt T when ready Temp 82 C 28 7 Time 01 28 45 Date 01 01 0001 Notes New Curve Count Firmware Version V HIGH 1000 V HIGH 100 A VERS 7 00 300C V LOW 400 V 1LOW 10A 3 Reset Figure 4 DS Tracer is pre charged and ready to immediately take the curve page 12 Installation amp Taking I V Curve DS 1000 Operating Manual After pressing the Take Curve button the DS Tracer takes approximately 2 to 10 seconds to take the curve and plot the data as shown in Figure 5 The new curve data is automatically added to the worksheet However the worksheet is not automatically saved to disk WRC Curves ivd Jaks ur File Edit Curve View Format Settings Tabs Window Help i New 3 Open save Print Curve 45 Quick Curve 88 Normalize L amp EME Curvesivd MuliCuve 1 Cu
6. IVPC Refer to the IVPC help system for details Note Pyranometers do not need to be used to sweep an l V curve Connect thermocouples to the DS 1000 Refer to the IVPC help system for details Thermocouples are not required to sweep an I V curve Connect the DS Tracer test lead to the DS Tracer before connecting the test lead to the PV system Connect the red clip to PV positive and the black clip to PV negative Be sure to connect the tracer to the PV system through a system disconnect switch rated for Isc and Voc The DS Tracer is now ready to take I V curves From the Curve menu in IVPC select New Curve Edit I V curve information such as name and site as needed When ready press the Take Curve button to begin the I V sweep The l V curve is displayed as soon as the curve sweep is complete To take another I V curve of the same PV system repeat step 5 7 To test another PV subsystem open the PV system disconnect switch Remove the cables and repeat steps 4 and 7 When finished taking curves open the PV system disconnect switch Disconnect the DS Tracer from the PV system Switch off the power to the DS Tracer DS 1000 Operating Manual Panel Layout page 15 2 0 Panel Layout This section describes the DS 1000 photovoltaic I V curve tracer in more detail The DS Tracer generates a complete current voltage I V curve that characterizes the photovoltaic system under test Figure 7 shows the front panel layout of the D
7. IVPC for Windows program controls the DS Tracer The computer running the IVPC application may be connected to the DS Tracer by RS 232 serial or USB Most DS Tracer operations are performed with the IVPC program Refer to the IVPC help system for details on operating the DS 1000 I V Tracer However the basic steps for using the DS Tracer are Install and run IVPC for Windows Connect the DS Tracer to the computer either RS 232 or USB Connect pyranometers and thermocouples to DS Tracer Turn on the tracer power and connect DS Tracer test leads to PV array From the Curve menu select New I V Curve or press the New Curve button on the toolbar Enter curve information Press the Take Curve button when ready to sweep the I V curve IVPC automatically displays the I V curve and adds it to the IVPC worksheet To proceed with the Installation amp Quick Start the following are needed DS Tracer I V curve tracer and test leads IVPC CD ROM or IVPC download from www daystarpv com PC computer running the Microsoft Windows operating system XP through 8 e Serial or USB cable to connect a computer to the DS Tracer page 6 Installation amp Taking I V Curve DS 1000 Operating Manual IVPC Installation IVPC is written for use with Windows XP through 8 which must be running to operate IVPC To install IVPC insert the IVPC CD ROM in the computer Open the IVPC CD ROM or alternately IVPC files downloa
8. Pin 16 3 Pin 4 Pin 17 4 Pin 6 Pin 19 5 Pin 7 Pin 20 6 Pin 9 Pin 22 7 Pin 10 Pin 23 8 Pin 12 Pin 24 COM 2 5 8 11 15 18 21 24 N C 13 DS 1000 Operating Manual Additional Capabilities page 29 Multiple Current Ranges The standard DS 1000 includes three current ranges 1 10 and 100 Amperes Before an l V curve is taken select one of these three ranges using IVPC Inadvertently selecting a low range when the high range is required will not damage the DS 1000 However the displayed l V curve will not include current values higher than the selected range External Command Set Typically the IVPC program controls the DS 1000 however users may want to write software to perform custom tracer operations or integrate the DS 1000 into a larger data acquisition system This is possible using commands sent to the DS 1000 through its RS 232 serial or USB control ports Refer to the DS 1000 Command Reference manual for details The DS 1000 uses a significantly different command set then previous Daystar l V tracers Daystar strongly recommends using the latest command set However the DS 1000 has legacy support for the older command set should the user need to use the DS 1000 in a system already using the older commands page 30 Troubleshooting DS 100C Operating Manual 7 0 Troubleshooting Data is not plotted after taking an l V curve Proper connection has not been made to PV system l V curve is flat
9. by pass diode to protect thin film PV modules The by pass diode should be rated to handle the instantaneous peak current created by shorting the pre charge capacitor through the by pass diode The DS 1000 design ensures this current will not exceed 150 A and lasts less than 2 ms The diode reverse voltage rating must be greater than module Voc A Motorola MR750 series rectifier or similar is recommend This rectifier has a reverse voltage rating of 50 V and can handle peak currents over 300 A DS 1000 Operating Manual Additional Capabilities page 27 6 0 DS 1000 Additional Capabilities The DS 1000 tracer has auxiliary capabilities These include analog circuits for reading external temperatures and irradiances Temperature amp Irradiance Inputs The DS 1000 has two thermocouple temperature inputs and two dual 5 way binding posts for connecting pyranometers Using these inputs is optional and they are not needed to take I V curves The temperature and irradiance inputs are enabled using the AUTO feature of IVPC When a curve is taken the temperature and irradiance inputs are sampled immediately before the DS 1000 sweeps a curve Refer to the IVPC help for details on using these inputs when taking I V curves Temperature Connections Two standard thermocouple connectors are available on the front of the DS 1000 A standard DS 1000 comes with Type T thermocouple connectors In order to accurately acquire temperature data only
10. front panel to the DC Power connector This is a standard banana jack connector Connect the DC positive and negative to the red and black jacks respectively The charge circuit uses a maximum of 1 A and requires a minimum of 16 V If using a PV module for recharging the open circuit voltage of this module should page 24 Maintenance DS 1000 Operating Manual not exceed the maximum rating shown on the DS Tracer front panel When connected to a supply that produces less than 1A the DS Tracer simply takes longer to recharge The internal charging circuitry limits the DC charging current Therefore power sources with current capabilities greater than 2 A can be used For example a 5 A PV module could be used The DS Tracer will only draw the current it needs for charging Unlike charging from an AC power source when using a DC source such as a PV module DS Tracer operating power may reduce the available charge current and slow battery charging The automatic charging system maintains the battery at its peak charge level and will not overcharge the battery When the battery is fully charged the full charge indicator comes on The DS Tracer can be either on or off when recharging the battery It will not harm the battery to leave the DS Tracer connected to the power source after the battery is fully charged Note The full charge indicator may come on for a short time if the charging power is removed before the DS Tracer is fully cha
11. port is a standard USB Type A port This port is not used to control the DS 1000 I V tracer It is used to update the I V curve tracer internal firmware In the event that an update is needed the proper use of this port will be described at that time This port may also be used for advanced features in future releases of DS 1000 firmware or IVPC page 18 Panel Layout DS 1000 Operating Manual Main USB Port All DS Tracer operations are controlled with commands sent to the DS Tracer through this USB port or the RS 232 port This port is a standard USB Type B port Normally the DS Tracer functions are controlled with the IVPC software but custom software can control the DS Tracer using the DS Tracer command codes Refer to the DS 1000 Command Reference manual for details Thermocouple Inputs The standard model DS 1000 is configured with two Type T thermocouple inputs for measuring PV array module temperatures Refer to the IVPC Help system for details on making temperature measurements and Appendix C DS 1000 Technical Specifications RS 232 Serial Port All DS Tracer operations are controlled with commands sent to the DS Tracer through this serial port or the USB port This port is a standard 9 pin RS 232 port This port is configured as a DCE device Normally the DS Tracer functions are controlled with the IVPC software but custom software can control the DS Tracer using the DS Tracer command codes Refer to the DS 1000 Co
12. safety it is recommended that connections be made to the PV array through a system disconnect switch rated at full PV power With the test lead attached to the DS Tracer connect the test leads to the PV system page 8 Installation amp Taking I V Curve DS 1000 Operating Manual Starting IVPC The following description assumes the use of IVPC 3 IVPC opens to the Data Grid window shown in Figure 1 IVPC Data Grid window The Data Grid is a spread sheet that lists all of the I V curve data files stored in the I V curve worksheet When starting IVPC for the first time the Data Grid may be empty if no l V curves have been taken WWPC ACME Curves ivd ES File Edit Curve View Format Settings Tabs Window Help New 23 Open save cd Print Curve 19 Quick Curve CurvelD Name Module Date Time Power Isc Voc Ipeak peak Fill Factor Irad1 Templ IO 1 ACMESoar odt 8 01 01 0001 01 28 45 52058 19060 365 560 17503 298790 1 035 453 O 2 ACMESoa 10140140001 01 28 45 51057 19 350 358 920 17 776 291 728 1035 453 3 ACME Sola od1 8 10140140001 01 28 45 52437 19740 353780 18134 283181 1035 453 4 ACME Solar od1 8 01 01 0001 01 28 45 4 9665 18670 354280 17151 283570 1 035 453 5 ACMESolar adt 8 01 01 0001 01 28 45 50382 18790 3571000 17 261 281875 1 085 4
13. 53 6 ACMESolar od1 8 01 01 0001 01 28 45 5231 6 19060 365560 17509 298 790 1235 453 7 ACME Solar od 8 0170170001 01 28 45 51857 19350 356920 17776 291 728 1035 453 8 ACMESole od18 01 01 0001 01 28 45 52437 19740 353 780 18134 283161 1 035 453 ACMESoler 9818 01 01 0001 01 28 45 318670 354280 17151 289570 1035 453 10 ACME Solar od 8 01 01 0001 01 28 45 18790 357100 1721 291875 1035 453 ACMESolar odt 01 01 0000 01 28 45 19060 385 580 17 509 298790 1 035 453 O 12 ACME Soler 01 01 0001 01 28 45 18350 358920 17778 291728 1 035 453 13 ACMESoa od18 01 01 0000 01 28 45 19740 353780 18194 289161 1 035 453 O 14 ACMESolar od18 01 01 0001 01 28 45 8 354280 17151 288570 1 035 453 15 ACMESolr 01 01 0001 01 28 45 357100 1721 291875 1 035 453 18 ACMESolar od18 01 01 0001 01 28 45 18060 365 560 17509 298790 1 035 453 17 ACMESolr od18 0101 0001 01 28 45 19350 356 920 17776 291728 1 036 453 O 18 ACMESoa 01 01 0001 01 28 45 19740 353780 18134 289 161 1 035 453 18 ACME Solar od 8 01 01 0000 01 2045 49665 18670 354280 1711 289570 1 035 453 20 ACMESol 8 01 01 0000 012845 50382 18790 357100 17261 291 875 1 035 453 21 ACMESolar od1 8 01 01 0000 01 28 45 52158 19 060 3550 17 509 298790 1 035 453 O 22 ACMESca 01 01 0001 01 28 45 51
14. 857 19350 356920 17776 29178 1 085 453 23 ACMESdar od18 01 0 0001 01 28 45 52437 19740 353 780 18134 289161 1 035 453 Figure 1 IVPC Data Grid window The Data Grid is as a detailed list of the I V curves In addition to curve names the data grid displays other curve data such as peak power or module ID Refer to the IVPC Help system for details DS 1000 Operating Manual Additional Capabilities page 9 Taking an I V Curve Before taking a curve turn on the DS Tracer and connect it to the PV system Connect the computer running IVPC to the DS Tracer From the Curve menu shown in Figure 2 select New Curve or press Ctrl T mi IVPC ACME Curves ivd Edit Curve View Format Settings Tabs Window BE New Curve Ctrl T 19 Quick Curve Ctrl Q Auto Curves Ctrl U it File 1 New Normalization 7 Curves ivd B Normalize Ctrl Shift N Auto Normalize Cun Auto Fill Enabled 001 01 28 45 5 001 01 28 45 5 L 3 ACME Solar od 1 8 01 01 0001 01 28 45 5 4 Solar od 1 8 01 01 0001 01 28 45 4 Figure 2 Select New Curve in the Curve menu to take an I V curve A Note Some figures shown in this manual may vary Please refer to the IVPC manual for the most up to date information on using IVPC page 10 Installation amp Taking I V Curve DS 1000 Operating Manual After starting a
15. ATH OR SERIOUS INJURY IF THE FOLLOWING PRECAUTIONS ARE NOT FOLLOWED THIS INSTRUMENT MUST ONLY BE USED FOR TAKING ELECTRICAL CURRENT AND VOLTAGE l V CURVES OF PHOTOVOLTAIC PV SOLAR MODULES THIS INSTRUMENT MUST NOT BE USED BEYOND ITS OPERATING RANGE THIS INSTRUMENT MUST NOT BE USED BY PERSONNEL WHO DO NOT HAVE EXPERIENCE HANDLING HIGH VOLTAGE DC AND PHOTOVOLTAIC MODULES THIS INSTRUMENT MUST NOT BE USED DURING RAIN SNOW SLEET OR IN ANY AREA OF HIGH MOISTURE SUCH AS AREAS WITH STANDING WATER OR MUD THIS INSTRUMENT MUST NOT BE USED IF IT IS NOT FUNCTIONING AS DESCRIBED IN THIS USER MANUAL page iv DS 1000 Operating Manual NOMENCLATURE A Hz Amperes or Amp Hertz Current Current at peak power Short Circuit Current The maximum current a photovoltaic cell can generate with the output terminals shorted Current Voltage Photovoltaic Voltage Open Circuit Voltage The maximum voltage a photovoltaic cell can generate with the output terminals open circuited Voltage at peak power DS 1000 Operating Manual Additional Capabilities page 5 1 0 Installation amp Taking I V Curves Basic Description The standard DS 1000 Tracer has three user selectable current ranges 1 10 and 100 Amperes three automatically selected voltage ranges 10 100 and 1000 Volts two irradiance and two temperature measurement inputs Unless otherwise noted this manual refers to standard DS 1000 models A computer running the
16. RP ER ECRIRE TE IE oen tide 27 Irradiance Connections eme eene 27 Aux Input Connections eem 28 Multiple Current Ranges mee eere 29 External Command Set E eene nennen 29 7 0 Proubl shooting ette tiber Ie tiii 30 Appendix DS Tracer ERROR CODES eesesseeeeeeeeeeene nennen nnn 31 Appendix DS 1000 USB Drivers nnnennnnannnnnnnnnnanannannnnnanannannnnnannnnannanaanannannnnannna 33 Appendix C DS 1000 Technical 35 Measurement ACCIAO aa ee E n nnne nennen nnn 35 PV Voltage ACCUracy does e e Rte Rab a ee ats 35 PV Current ACCUracy eoe D epe ha 35 Irradiance and Aux Input Accuracy 35 Temperature c ege tt eed needa red ege nti seceded Pedo DAR 35 General Specifications eene ener 36 DS 1000 Operating Manual page iii WARNINGS THE IMPROPER USE OF THIS INSTRUMENT CAN PRESENT AN ELECTRICAL SHOCK HAZARD THAT CAN CAUSE DEATH OR SERIOUS INJURY THIS INSTRUMENT SHOULD ONLY BE USED AS DESCRIBED IN THIS OPERATIONS MANUAL KKK A WARNING THIS INSTRUMENT MAY PRESENT AN ELECTRICAL SHOCK HAZARD WHICH CAN RESULT IN DE
17. S 1000 Each of the key components is described in detail in the following section www daystarpv com ab daystar inc M O Q9 05 1000 PHOTOVOLTAIC I V CURVE TRACER AT A uA 1 PV System Connector 7 AUX USB Port 2 AC Power Entry amp Fuse 8 Main USB Port 3 DC Supply Input 9 Thermocouple Inputs 4 DC Supply Input Fuse 10 RS 232 Serial Port Connector 5 On Off Switch 11 AUX Analog Inputs 6 Full Charge Indicator 12 Irradiance Inputs Figure 7 Face plate of the DS Tracer page 16 Panel Layout DS 1000 Operating Manual PV Test Lead Connector When an I V curve is taken the load current flows through the test lead into DS Tracer The red and black test clips go to PV array positive and negative terminals respectively The test cable contains separate voltage sense wires to measure the PV voltage at the test clips This 4 wire measurement technique avoids measurement errors caused by voltage drops in the test leads For maximum safety the DS Tracer should be connected through a PV system disconnect rated at the PV system Voc and lsc values See Figure 8 A system disconnect switch provides a way to break the electrical connection should the DS Tracer have a major internal failure System Disconnect Switch Test Lead PV Array Figure 8 Use of PV system disconnect switc
18. alculated and displayed with the curve Irradiance and temperature data and array identification may be added to each I V curve The irradiance and temperature data are either entered by the operator using IVPC or sampled by the DS 1000 DS 1000 Operating Manual Theory of Operation page 21 Curve Sweep The DS Tracer sweeps an I V curve by switching the PV system to a bank of capacitors As these capacitors charge the PV system voltage increases until open circuit voltage is reached While the voltage is increasing and the current to the capacitors is decreasing from its maximum short circuit value the voltage and current are sampled by high speed analog to digital converters These data points define the l V curve Pre Charge Before acquiring data the DS 1000 reverse charges its capacitive load to approximately 15 V This negative pre charge is used to offset any voltage drops created by the test leads and to allow any switching transients to settle before Is is reached This method allows a true short circuit current reading to be made After the capacitive load charges to Voc the curve sweep is complete At this point the circuitry discharges the capacitors through a resistive load Sweep Speed Curve sweep time varies with PV system current and voltage The sweep is typically less than one second but can be as long as 10 seconds The complete cycle actually begins with a discharge of any residual voltage on the capaci
19. daystar inc DS 1000 I V CURVE TRACER User Manual Daystar Inc 3240 Majestic Ridge Doc Version 7000 Las Cruces NM 88011 May 2014 575 522 4943 pvvern zianet com http www daystarpv com This I V curve tracer was built to Daystar Inc specifications by Raydec Inc 8210 La Mirada Suite 700 Albuquerque New Mexico 87109 DS 1000 Operating Manual CONTENTS elg pc i WARNINGS e c iii NOMENCLATURE RES iv 1 0 Installation amp Taking l V Curves nnonrnnaenannnnnnnannnnnannanannnnnannnnannnnnannnnannnnannnnnannnnana 5 Basic Description ss terret e 5 IVPC Installation c ee aede erede e ede ag eco ege tt 6 Precautions OE RE RE 6 Connecting a Computer to the 05 7 Connecting a PV Module to the 08 7 Starting IVP Gant ate eR ctu Feet gout 8 Taking an EV Curve aca Aube t n ede A t eg e aa its 9 If There Issa Error iiie t ot tenete ne pee m eo epo ci Pre ene 13 Displaying FY CUNE S LEE 13 Summary of Steps for Taking l V Curves 14 2 0 Pan l LAYOUU es A ERE EA AAA A ETE 15 PV Test Eead Connection s oe d o rem e ree Te e d aie 16 AC Power Entry amp 16 DC Supply Input amp Fuse wicca ence tne rte e eade ve ed
20. ded from www daystarpv com and run the setup exe program The setup program prompts for information on where to install IVPC If unsure use the defaults which create an IVPC sub directory within the Windows programs folder IVPC Setup automatically installs the necessary files in the IVPC directory and makes additions to the Windows system directory Precautions There are several precautions to observe before using the DS Tracer Keep the DS Tracer battery charged The DS 1000 has a universal power supply that works with AC line voltages from 85 Vac to 264 Vac 50 60 Hz Turn the DS Tracer power on when making or breaking connections to a PV system Connect the DS Tracer to the PV array through a PV system disconnect switch capable of interrupting the short circuit current of the array at peak power voltage This allows disconnecting the DS Tracer from the PV system if a problem occurs Do not connect the DS Tracer to anything other than an open circuit PV system Be sure the PV array is electrically isolated from power conditioning equipment such as charge controllers or inverters Do not connect the DS 1000 Tracer to a PV system with an open circuit voltage greater than 1000 Volts Do not connect the DS Tracer to any PV system with a short circuit current greater than maximum 100 Amperes for a standard DS 1000 A The DS Tracer RS 232 and USB ports irradiance inputs temperature inputs auxiliary analog inputs and a
21. h AC Power Entry amp Fuse Connecting the DS Tracer to an AC power source recharges the DS Tracer battery It is not necessary for the tracer to be on Refer to section Battery Charging and Care in section 4 0 Maintenance for details of battery charging DS 1000 Operating Manual Panel Layout page 17 DC Supply Input amp Fuse The DS Tracer may be powered or recharged from an external DC power source This source could be a PV module Refer to section Battery Charging and Care in section 4 0 Maintenance for details of battery charging ON Off Switch This switch turns on the DS Tracer power Turn this switch on before connections are made to a PV array The curve tracer takes approximately 10 seconds to initialize after it is turned on The DS Tracer automatically turns itself off if a curve has not be taken for 15 minutes This feature protects the DS Tracer battery If the DS Tracer has turned itself off switch the power switch off wait several seconds and turn the switch back on Full Charge Indicator When this LED lights its indicates that the DS Tracer battery is fully charged When fully charged this indicator remains on while the DS Tracer is plugged into AC power Sometimes this LED will turn on briefly if the AC power cord is unplugged before the battery is fully charged This occurrence does not indicate a fully charged battery Aux USB Port This port supports auxiliary DS 1000 operations This
22. mary driver will be a USB device driver labeled DS 1000 I V Tracer The second driver will be a virtual COM port also labeled DS 1000 I V Tracer This virtual COM port will function as a conventional COM port While normally there is no reason to use the virtual COM port when using IVPC 3 in some cases it may be useful to avoid problems when using the USB port directly Note This does not affect how the tracer is connected only how the Windows operating system sees the tracer Either directly as a USB device or indirectly through a COM port IVPC 3 supports COM ports 1 through 16 Therefore after being created the virtual COM port must be assigned a COM port number in this range It is possible for the operating system to assign a COM port number outside this range even if a COM port number from 1 to 16 is not in use Use the Windows device manager to change the COM port number assigned to this virtual COM port to a value from 1 to 16 Often Windows will warn that a COM port is in use even when the port is known to be unused at the time If the port is known to be available reassign it to the necessary value from 1 to 16 Consult the Microsoft documentation and help system for details on using the device manager Note If a conventional RS 232 COM port is available there is no advantage to using the DS 1000 USB port and it is not necessary to install these USB drivers However many notebook computers do not have COM
23. matching thermocouple types should be used The thermocouple inputs are electrically isolated from the PV system but not isolated from other analog circuits or the computer connections Therefore it is necessary that the thermocouple be electrically insulated when bonded to a surface Irradiance Connections There are two dual 5 way binding posts for pyranometer inputs located on the front panel of the DS 1000 These inputs can accommodate x 5 V signals and accurately measure millivolt signals These inputs can be used for any analog voltage measurement within the range of the DS 1000 Refer to the Appendix C DS 1000 Technical Specifications for details on measurement ranges page 28 Additional Capabilities DS 1000 Operating Manual Aux Input Connections There is a single 25 pin connector for measuring auxiliary Aux inputs signals These inputs accommodate 5 V signals and accurately measure millivolt signals These inputs can be used for any analog voltage measurement within the range of the DS 1000 Refer to Appendix C DS 1000 Technical Specifications for details on measurement ranges Note These inputs are fully differential and the applied signal must be referenced to circuit common COM For example jumper the negative input to COM 131211109 8 765 43 2 1 25 24 23 22 21 20 19 18 17 16 15 14 Figure 10 Aux Input Connector Aux Chan Aux Aux 1 Pin 1 Pin 14 2 Pin 3
24. mmand Reference manual for details The DS Tracer uses the following default RS 232 format 9600 Baud No parity 8 data bits 1 stop bit DS 1000 Operating Manual Panel Layout page 19 Aux Analog Inputs There are 8 auxiliary Aux inputs These have similar functionality to the irradiance inputs with the exception that there is no internal resistor referencing the inputs to the DS Tracer common Refer to the IVPC Help system for details on using this feature Refer to Aux Input Connections in section 6 0 05 1000 Additional Capabilities for details on connecting to these inputs Irradiance Inputs The model DS 1000 has two irradiance inputs for measuring pyranometers These inputs measure DC voltages only In order to use a reference cell the cell must have a shunt resistor attached to convert the cell current to a voltage Refer to the IVPC Help system for details on making temperature measurements and Appendix C DS 1000 Technical Specifications These inputs are differential but there is a 10 K resistor from the negative black input and the internal circuit common Therefore the pyranometer can be either electrically referenced to the same common as the other DS Tracer inputs such as the computer or it can be electrically floating page 20 Theory of Operation DS 1000 Operating Manual 3 0 Theory of Operation The DS Tracer obtains an l V curve by varying the electrical impedance connected across the PV array
25. new curve IVPC opens a new curve window as shown in Figure 3 This window provides areas to enter curve information identifying the I V curve The DS Tracer may take several seconds to initialize the tracer hardware A status message indicating that the DS Tracer is pre charging is displayed in the area normally used to plot the curve IVPC ACME Curves ivd ERX ur File Edit Curve View Format Settings Tabs Window Help i New 3 Open save Print New Curve 49 Quick Curve f Normalize Normalization ACME Curvesivd MultiCurve 1 Curve 2 Peak Power w 5 186 Fill Factor 2 08 a 291 73 Voc V 35692 3 Ipeak 17 776 Ise A 19 350 Name ACME Solar Site Far ide Sub System Section 3 Module od 1 8 Misc Operational Test Imad 1 w m2 1 035 Irrad 82 wW m2 831 Pre Charging DS Tracer Temp 1 C 453 Temp 2 287 Time 01 28 45 Date 01 01 0001 Notes New Curve Count Firmware Version V HIGH 1000 V HIGH 100 A 5 VERS 7 00 300C V LOW 400 V I LOW 10 A 3 Reset EZH Figure 3 New Curve screen while DS Tracer is pre charging DS 1000 Operating Manual Additional Capabilities page 11 After initialization the status message changes and the Take Curve button is enabled as shown in Figure 4 This status message indicates that a curve can be taken by pressing the Take Curve button or by pressing Alt T ia IVPC
26. ng and Care The DS Tracer contains a 12 Volt sealed maintenance free lead acid battery 5 AH Cyclon brand 0809 0012 manufactured by EnerSys The battery is designed for 400 cycles of a 50 percent discharge Using the DS Tracer for 6 hours continuously discharges the battery 50 percent If the DS Tracer were used for 6 hours every day the battery should have a minimum life of 13 months one discharge charge cycle a day Fully charging the DS Tracer after every use increases battery life The DS Tracer is programmed to turn itself off after 15 minutes without a command This reduces the possibility of completely discharging the battery The DS Tracer battery may be charged in two ways AC line power or a DC source such as a PV module The DS 1000 has a universal AC power supply and therefore will work with single phase AC line voltages from 85 Vac to 264 Vac 50 60Hz To charge the battery from AC line power connect the tracer to the AC source with the AC power cord provided The tracer will immediately start charging the battery Battery charging is independent of using the DS 1000 tracer Therefore the tracer may be used to take curves using AC power The battery will continue to charge while the tracer is used A DC supply such as a PV module can also recharge and power the DS Tracer This feature is useful when working in remote locations without AC power Connect a DC Voltage source within the range specified on the DS Tracer
27. output terminals Varying the impedance from zero to infinity causes the array operating point to change from I to V The DS Tracer accomplishes this impedance change by connecting the array to a capacitive load As the capacitor charges the array moves through its operating range and presents a set of current and voltage values that form the I V curve When the capacitor load reaches V e data sampling stops A NOTE The DS 1000 uses a sophisticated switching technique that actively controls the start of the sweep Although this controlled switching is designed to detect fault conditions and take appropriate action to protect the DS 1000 the user is encouraged to ensure the DS Tracer is always used with PV systems within its voltage and current rating and that auxiliary equipment such as inverters power conditions and charge controls are not connected to the PV system while sweeping l V curves Data Sampling The DS Tracer employs two high speed analog to digital converters to sample the current and voltage simultaneously One converter digitizes the array voltage while the other digitizes the array current The DS Tracer typically collects tens of thousands of data points and reduces this to 1000 points typically In addition to the l V data points the l V curve includes the values of open circuit voltage V and short circuit current Peak power voltage at peak power Vpk Current at peak power lpk and fill factor are c
28. ports and therefore it is necessary to install these DS 1000 USB drivers page B34 DS 1000 USB Drivers DS 1000 Operating Manual The DS 1000 USB drivers are located on the IVPC CD ROM supplied with the tracer in the DS 1000 USB Drivers folder This folder contains detailed instructions on how to install the drivers Note These instructions are not specific to the DS 1000 and were provided by the USB hardware manufacturer Therefore these instructions will not refer to the DS 1000 driver by name When first connecting the DS 1000 to a computer using the USB connection Windows recognizes that new hardware has been connected and begins the process of installing the driver The instructions on the CD ROM provide much more detail but in general have Windows use the drivers in the driver folder on the IVPC CD ROM using the Have Disk or Browse option Follow the steps as outlined in the driver installation instructions If using a virtual COM port confirm that the assigned COM port number is appropriate and if necessary change it to a number from 1 to 16 as described above Also be sure to set the COM port number in IVPC to match this setting DS 1000 Operating Manual Technical Specification page C35 Appendix C DS 1000 Technical Specifications Measurement Accuracy PV Voltage Accurac Range Error 25 C Error 0 50 C Resolution 1000 V 0 4 V 4 V 0 01 0 1
29. rged This occurrence does not indicate that the battery is fully charged During charging the front panel of the DS 1000 near the irradiance connectors may get slightly warm Exterior Cleaning The exterior surface of the DS Tracer may be cleaned with a soft cloth damped with water or a mild soap only Do not use detergents abrasive cleansers or other solvents Transportation Treat the DS Tracer similar to a notebook computer or other electronics While the DS Tracer is mounted in a heavy duty case this is NOT adequate to ship the unit as freight without using a shipping container Because of its weight it will likely be damaged if it is dropped or tossed Due to airline security Daystar does not recommend attempting to carry the tracer on board a commercial airplane as DS 1000 Operating Manual Maintenance page 25 carry on baggage A shipping container with foam packing is supplied as standard equipment with all DS 1000 curve tracers Daystar strongly recommends using this case anytime the DS 1000 is shipped DS Tracer Fuses The DS Tracer has two externally accessible fuses The first of the external fuses is located in the AC input power receptacle Power line surges or internal faults could cause this fuse to fail Return the DS Tracer for repairs if this fuse blows repeatedly Replace this fuse with the type indicated on the DS Tracer panel A second user replaceable fuse is the 2 Amp fast blow DC charging fuse This
30. rve 2 Peak Power w 5 186 Fill Factor 2 0 8 B Vpeak V 291 73 356 92 Unfiled v Ipeak 17 776 Isel 19 350 Name ACME Solar 25 m prae n 2 uL E E Sub System Section 3 Module od 1 8 20 Misc Operational Test Irad 1 w m2 1 035 Ji Irrad 82 w m2 831 ex Mel S Temp 1 C 453 P a d Temp 2 287 E lt 101 AE Time 01 28 45 1 Date 01 01 0001 5 T Notes 0 0 100 200 300 400 Volts Figure 5 Example of I V curve It s possible to return to the Data Grid without closing the curve window by clicking on the data grid tab far left tab as shown in Figure 6 Closing the I V curve window also opens the Data Grid tab Normatizacion run nz Pyral _ACME_Curves ivd MultiCurye 1 Curve 2 Peak Power fl 18R Fill Factor Figure 6 Moving to the Data Grid using tabs DS 1000 Operating Manual Additional Capabilities page 13 If There Is an Error There are several error messages IVPC may display when taking a curve The DS Tracer automatically turns off when it does not receive a command for 15 minutes This features helps to protect the DS Tracer battery If the DS Tracer has been on for more than 15 minutes without taking a curve it will power down and IVPC generates an error indicating that the DS Tracer does not respond Turn the DS Tracer power switch off wait several seconds and turn it back on Allow the tracer appro
31. t 17 READ i DM 17 Charge Indicatot eerie petet eet a e EP Cei e e ber p ote 17 5 uei theca kk toot Neat piv 17 Main USB POM pete epe oes mee ede Prnt dete Pee etel ta ene 18 Thermocouple Inputs 2 Rh t a a ha tede este er esee ene td 18 RS 232 SerlalBOort ic com te a teret telae e 18 Aux Analog TAPUS a a aeia teaiin A iaia i AA AAE AAAS ATATA eene eene teneret 19 irradiance INPUTS deo eder ine E te oen d e 19 page i page ii DS 1000 Operating Manual 3 0 Theory of 20 Data Sampling yi tk kal Ee eR EP ere ee ot e ede A 20 C rve Sweep ss enn p RR ED ED a al ahha koa 21 PIE EHAFGET Qe ge terere 21 Sweep Speed reset re fe teet e heme dagen ees Lage agents 21 A0 Maintenance corgo 23 Battery Charging and Care metesse asa aea eene 23 Exterior Cleaning EE E E ONE ERU ONG OUI ae Rae 24 Transportation iie mo tien er tr gc rere dtes ed ee vili ul aita 24 DS Tracet Fuses x REO de iere EUN Eus 25 5 0 Pre Charge Precautions eeeeeeeeeee esie ee eeeen nennen nnne annnm nannn nnn nnmnnn rasan erasa 26 6 0 DS 1000 Additional Capabilities cessisse nennen enne 27 Temperature amp Irradiance Inputs sssssssssss e 27 Temperature Connections e E RR ERR U
32. tors and a pre charge to 15 V curve sweep and finally another discharge pre charge period to ready for the next I V curve sweep Some PV systems are sensitive to how quickly an I V curve is taken The speed of a curve is most easily expressed in volts per second by taking the PV short circuit current in Amps lac and dividing it by the DS Tracer load capacitance in Farads The DS 1000 load capacitance varies depending on PV system voltage and current range selection There are four possible load capacitance values from approximately 2 500 uF to 11 600 uF page 22 Theory of Operation DS 1000 Operating Manual For example for a load capacitance value of 2 500 uF and a PV system with an Isc of 20A the rate would be Rate 20A 0 0025 F 8000 V S When comparing this value to the PV system it is best to normalize this rate to an individual PV cell This is done by dividing the rate by the number of PV cells in series If the previous example had fifty cells in series the rate of each cell would be 8000 V S 50 cells 160 V S cell Different PV technologies vary in their sensitivity to the charge rate It is left to the user to determine if there is reason for concern Often the PV module manufacturer can provide information concerning how quickly an I V curve can be swept on their modules Daystar Inc will also provide any assistance possible DS 1000 Operating Manual Maintenance page 23 4 0 Maintenance Battery Chargi
33. uxiliary charge inputs are all referenced to the same electrical common inside the tracer Therefore these devices must be either electrically floating or referenced to the same electrical common Note All of these connections are electrically isolated from the PV inputs DS 1000 Operating Manual Additional Capabilities page 7 Connecting a Computer to the DS Tracer The DS 1000 I V Tracer provides two interfaces an RS 232 and USB port The RS 232 interface uses a standard female 9 pin connector located on the DS Tracer front panel The standard USB connection is labeled Main USB Use either of these connections depending on the configuration of the computer running the IVPC program However only one of these ports should be connected at a time Note Special USB drivers must be installed on the computer in order to use the USB port See the section Appendix 05 1000 USB Drivers for details installing these drivers Connecting a PV Module to the DS Tracer The DS Tracer is connected to the PV array or module with the test leads provided Before connecting a PV module be sure the DS Tracer power switch is ON The test lead is designed to remain connected to the DS Tracer at all times It is typically unnecessary to remove this from the tracer A For safety the test lead should never be disconnected from the tracer while the other end is connected to a PV system Doing so could present an electric shock hazard A For
34. ximately 10 seconds to initialize Then retry as indicated on the error dialog box Other errors occur if the PV array voltage is too high or if it is zero or negative Follow the IVPC directions given when the error occurs Most errors occur immediately after selecting New Curve from the Curve menu The most common problem results from a communication error Incorrect COM port settings in IVPC may cause this problem The COM port settings must match the actual COM port on the computer Note If the COM port is a virtual COM port such as those created by USB to serial adapters or by the DS 1000 USB drivers it is possible that this COM port number has been inadvertently changed Use the Windows device manager to confirm the current COM port setting of the virtual COM port The COM port number set for this virtual port must match the COM port number set in IVPC Displaying l V Curves From the Data Grid double click a curve to display it Use the Multi plot feature under the View menu to display multiple curves on one plot Several options exist for displaying I V curves Refer to the IVPC Help system for details page 14 Installation amp Taking I V Curve DS 1000 Operating Manual Summary of Steps for Taking I V Curves 1 10 Connect the computer to the DS Tracer and start IVPC Turn the DS Tracer power switch ON Connect pyranometers to the DS 1000 If pyranometers are connected enter pyranometer constants in

DS-1000 I-V CURVE TRACER User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents