IMC100T Series Fast Ethernet Industrial Media
Contents
1. Note and signs represent the polarity of the wires that make up each wire pair All ports on this unit support automatic MDI MDI X operation you can use straight through cables See Figure below for all network connections to PCs or servers or to other switches or hubs In straight through cable pins I 2 3 and 6 at one end of the cable are connected straight through to pins I 2 3 and 6 at the other end of the cable The table below shows the IOBASE T 100 5 MDI and MDI X port pin outs Pin MDI X Signal Name MDI Signal Name 1 Receive Data plus RD Transmit Data plus TD 2 Receive Data minus RD Transmit Data minus TD 3 Transmit Data plus TD Receive Data plus RD 6 Transmit Data minus TD Receive Data minus RD Switch Router or PC 3 TD 4 5 3 TD 6 TD 6 1D 1 RD 4 1 RD 2 RD lt _ _ _____ _ _ gt 2RD AT IMC100T SCSM and 00 5 Fast Ethernet Industrial Media Converters 12 Hardware Description Ports Switch Router or PC 3 TD 3 TD 6 TD 6 TD 1 RD 1 RD 2 RD 2 RD 2 7 2 Fiber Port The fiber port of SC type connector can work in multi mode 2Km or single mode 30Km When you connect the fiber port to another one please follow the figure below to connect accordingly Wrong connection will cause the port cannot work normally SC Connector2. MV Allied Ielesis 100 5 5 100 5 Fast Ethernet Industrial Media Converter User Manual 613 001984 Rev Copyright 2001 2014 Allied Telesis Holdings K K all rights reserved No part of this publication may be reproduced without prior written permission from Allied Telesis Inc Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis Incorporated All other product names company names logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners Allied Telesis Inc reserves the right to make changes in specifications and other information contained in this document without prior written notice The information provided herein is subject to change without notice In no event shall Allied Telesis Inc be liable for any incidental special indirect or consequential damages whatsoever including but not limited to lost profits arising out of or related to this manual or the information contained herein even if Allied Telesis Inc has been advised of known or should have known the possibility of such damages Preface FCC Warning This Equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installa tion This equipment gener
3. Tx Tx Rx p Cable Witing SC to C tx A Rx Tx 8 Rx Warning This is a Class Laser LED product Don t stare into the Laser LED Beam AT IMC100T SCSM 00 5 Fast Ethernet Industrial Media Converters Mounting Installation DIN Rail Mounting 3 Mounting Installation 3 1 DIN Rail Mounting The DIN rail clip is screwed on the industrial switch when out of factory If not please refer to the following steps and figure to secure the DIN rail clip on the switch 3 1 1 Use the screws to screw on the DIN rail clip on the industrial switch 3 1 2 To remove the DIN rail clip reverse step 3 1 1 DIN Rail FIGURE 3 1 DIN rail Mounting 3 1 3 To hang the industrial switch on the DIN rail first position the rear side of the switch directly in front of the DIN rail Make sure the top of the clip hooks over the top of the DIN rail AT IMC100T SCSM and 00 5 Fast Ethernet Industrial Media Converters 14 Mounting Installation DIN Rail Mounting FIGURE 3 2 Push the chassis down onto the upper DIN Rail track 3 1 4 Then push the unit downward FIGURE 3 3 Put the chassis down AT IMC100T SCSM AT IMC100T SCMM Fast Ethernet Industrial Media Converters 15 Mounting Installation Wall Mount Plate Fixing 3 1 5 Check the DIN Rail clip is tightly fixed on the DIN rail 3 1 6 To remove the industrial switch from the track reverse the step
4. 328 feet e Diagnosing LED Indicators the unit can be easily monitored through panel indicators to assist in identifying problems which describes common problems you may encounter and where you can find possible solutions f the power indicator does not light up when the power cord is plugged you may have a problem with power cord Then check for loose power connections power losses or surges at power outlet IF you still cannot resolve the problem contact your local dealer for assistance e Ifthe LED indicators are normal and the connected cables are correct and the packets still cannot transmit please check your system s Ethernet devices configuration or status AT IMC100T SCSM and 00 5 Fast Ethernet Industrial Media Converters 18 Hardware Installation Selecting a Location 6 Hardware Installation 6 1 Selecting a Location Here are the guidelines for choosing a location for the media converter The Fast Ethernet Industrial Media Converter may be installed on a wall or on DINRAIL Note The DINRAIL bracket must be ordered separately from the AT PC2002 POE media converter Caution The Fast Ethernet Industrial Media Converter must be powered only by a UL Listed power supply marked either LPS or Class 2 rated 56Vdc IA Caution The Fast Ethernet Industrial Media Converter must NOT be operated from Centralized DC battery e The site should provide easy access to the ports on the fro
5. Wiring the Power Input conte ecesi 6 9 Wiring the Fault Alarm Cont et eatin Jade 10 LED TRUCE AEGIS E A E E E TE EEE O 10 DIP Syitek eser gan apna ead 11 Nel 12 E S 14 Wall Mount Plate ee 16 Installing Copper Ethernet secedaseteen sa devousannees 17 Installing SFP Module and Fiber Cable ics ioe 17 Locatioun en 19 Tista Steps siine 3s es Shas baci 19 Overview Introduction Overview I I Introduction The Fast Ethernet Industrial Media Converter is a cost effective solution for the converting between 10 100Base TX and 100Base FX cabling it allows you to extend the cabling distance of your 100Base FX network to 2 kilometers for multi mode fiber or 40 kilometers for single mode fiber The Fiber Converter module gives you the option to choose from the most popular fiber cabling connectors SC multi mode and single mode connector 1 1 1 Dual Power Inputs To reduce the risk of power failure the Fast Ethernet Industrial Media Converter provides 12 48 VDC dual power inputs When the primary power input fails the device will automatically switch to the secondary power input 1 1 2 Flexible Mounting F
6. Cable 4 2 1 The cable between the link partner switch hub workstation etc and the converter must less than 100 meters 328 ft long and comply with the IEEE 802 3ab 1000 standard for Category 5e or above 4 2 2 Fiber segment using single mode connector type must use 9 125im single mode fiber cable You can connect two devices the distance of 10km or more accordingly with the SFP module capabilities Fiber segment using multi mode connector type must use 50 125 or 62 5 125im multi mode fiber cable You can connect two devices up to 550m distances 4 2 3 The small form factor pluggable SFP module is a compact optical transceiver used in optical communications for both telecommunication and data communication applications AT IMC100T SCSM 00 5 Fast Ethernet Industrial Media Converters 17 Troubleshooting 5 Troubleshooting e Verify that you are using the right power cord adapter DC 12 48V please don t use the power adapter with DC output higher than 48 or it will burn this converter down e Select the proper UTP STP cable to construct your network Please check that you are using the right cable Use unshielded twisted pair UTP or shield twisted pair STP cable for RJ 45 connections 10002 Category 3 4 or 5 cables for OMbps connections or 1000 Category 5 cable for I00Mbps connections Also be sure that the length of any twisted pair connection does not exceed 100 meters
7. Category 5 cable for Ethernet connection 6 2 7 Insert one side of Category 5 cables into the Ethernet port RJ 45 port The UTP port RJ 45 LED on the unit will light up when the cable is connected and network is active Please refer to the LED Indicators section for LED light meaning 6 2 8 Insert the fiber cable SC connector into the fiber port 6 2 9 When all connections are all set and LED lights all show in normal the installation is complete AT IMC100T SCSM and 00 5 Fast Ethernet Industrial Media Converters 19 Reviewing the Safety Guidelines 7 Reviewing the Safety Guidelines Please review the following safety guidelines before you begin to install the 000 5 Industrial Media Converter Note The amp indicates that a translation of the safety statement is available in PDF document titled Translated Safety Statements posted on the Allied Telesis website at www alliedtelesis com Note Refer to the documentation that comes with the SFP module to determine whether the module is a Class LED product or Class Laser product Warning Class Laser product amp LI Warning Do not stare into the laser beam a 12 Warning Class LED product a L3 Warning The fiber optic ports contain a Class laser device When the ports are disconnected always cover them with the provided plug Exposed ports may cause skin or eye damage L4 Warning Do not look directly at th
8. ast Ethernet Industrial Media Converter is extremely compact and can be mounted on a DIN rail or a wall so it is suitable for any space constrained environment 1 1 3 Wide Operating Temperature The operating temperature of the Fast Ethernet Industrial Media Converter is between 40 75 C With such a wide range you can use the Industrial Media Converter in some of the harshest industrial environments exist 1 1 4 Easy Troubleshooting LED indicators make troubleshooting quick and easy The LED indicators help you immediately diagnose the system power link status transmission speed and collision status 1 2 Features Standard 802 3 10 5 IEEE802 3u 100BASE TX 100BASE FX 802 3 Flow Control and Back pressure LED Indicator Power 1 Power 2 Fault FDX COL for Fiber LNK ACT for Fiber 100M for RJ45 LNK ACT for RJ45 Connector Fiber x 1 SC Multi mode 2Km or Single mode 30Km RJ 45 Socket x 1 CAT 3 5 10 100Mbps Twisted Pair cable Auto MDI MDI X and Auto Negotiation Function Support AT IMC100T SCSM and 00 5 Fast Ethernet Industrial Media Converters 5 Overview Features Fiber Parameters SC Multi mode 50 125um 62 5 125um SC Single mode 9 125um Available distance 2km Multi mode 30km Single mode Wavelength 1310nm Multi mode Single mode Link Lose Forward TX gt Fiber If TX port link down the media converter will force Fiber
9. ates uses and can radiate radio frequency energy It may cause harmful interference to radio com munications if the equipment is not installed and used in accordance with the instructions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or tele vision reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures AT IMC100T SCSM and 00 5 Fast Ethernet Industrial Media Converters Table of Contents TPOGUCH eee a eta es ies a eee ie Skid ak 5 Feie 5 Packing List 7 Safety PLECAULION 7 Front Panel ele Adee eh eee el eh el hI 8 TOP VIEW ae UO eS MOE ae 8
10. e fiber optic cable ends or inspect the cable ends with an optical lens lt 7 16 Warning To prevent electric shock do not remove the cover No user serviceable parts inside This unit contains hazardous voltages and should only be opened by a trained and qualified technician To avoid the possibility of electric shock disconnect electric power to the product before connecting or disconnecting the LAN cables a El Caution Air vents must not be blocked and must have free access to the room ambient air for cooling a E6 Warning Operating Temperature This product is designed for a maximum ambient temperature of 75 degrees a E53 All Countries Install product in accordance with local and National Electrical Codes a E8 Warning Do not strip more than the recommended amount of wire Stripping more than the recommended amount can create a safety hazard by leaving exposed wire the terminal block after installation Warning Check to see if there are any exposed copper strands coming from the installed wire When this installation is done correctly there should be no exposed copper wire strands extending from the terminal block Any exposed wiring can conduct harmful levels of electricity to persons touching the wires E12 Warning Only trained and qualified personnel are allowed to install or to replace this equipment a 14 Caution Do not install in direct sunlight or a damp or dusty place a 16 Note Circuit Overload
11. e following table for further details Table 2 1 Definition of LED indicators LED Color Description Pl Green On Power input is active Off Power input is inactive Blink 2 Green On Power input is active Off Power input is inactive Blink Fault Red On Power input 1 or 2 has failed Off Power input 1 or 2 are both functional or no power inputs Blink FDX COL for Fiber Amber On Full duplex mode Blink Packet collistion occured Off Half duplex mode AT IMC100T SCSM 00 5 Fast Ethernet Industrial Media Converters 10 Hardware Description DIP Switch Table 2 1 Definition of LED indicators LED Color Description LNK ACT for Fiber Green On Connected to network Blink Networking is active Off Not connected to network 100M for RJ 45 Amber On Link to 100Mbps network Blink Off Link to 10Mbps network LNK ACT for RJ 45 Green On Connected to network Blink Networking is active Off Not connected to network 2 6 DIP Switch Table 2 2 DIP Switch Status Description S W No Status Description 1 On Enables Port Power Alarm Off Disables Port Power Alarm 2 On Enables LLF Off Disables LLF 3 On 100Base FX Half mode Off 100Base FX Full mode 4 On Media mode 100TX to 100FX Off Switching mode Link Lose Forwarding DIP Switch 2 W
12. ew located near to the power socket AT IMC100T SCSM and 00 5 Fast Ethernet Industrial Media Converters Hardware Description Wiring the Power Inputs DC Source 2 DC Source 1 FIGURE 2 2 Top Panel of the Industrial 10 100TX to 100 BaseFX Media Converter 2 3 Wiring the Power Inputs Please follow the steps below to insert the power wires V V V V FIGURE 2 3 V and V Contacts 1 Insert the positive and negative wires into the V and V contacts on the terminal block connector FIGURE 2 4 Wire clamp Screws 2 Tighten the wire clamp screws to prevent the wires from loosing AT IMC100T SCSM and 00 5 Fast Ethernet Industrial Media Converters 9 Hardware Description Wiring the Fault Alarm Contact 2 4 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block as the picture shows below Connect the wires to form a normally close circuit When fault events including power failure port link failure occur the loop will become an open circuit FIGURE 2 5 Fault Alarm Contacts Insert the wires into the fault alarm contacts Note Use Copper Conductors Only Tighten to 5 Ib in Note The wire gauge for the terminal block should be in the range between 12 24 AWG 2 5 LED Indicators LED indicators located on the front panel display the power status and network status of the Managed Industrial Switch Please refer to th
13. hen LLF enabled it allows UTP link failures to be reported to the fiber side and also allows Fiber link failures to be reported to the UTP side Therefore a link fault pass through feature is provided in both UTP and Fiber side Media mode DIP Switch 4 When media mode is enabled ON it operates with the minimum latency The transmis sion flow does not wait until entire frame is ready but instead it forwards the received data immediately after the data being received And TP port should be forced at 100M in this application When DIP Switch is in switching mode OFF the con verter function is the same as a Switch Hub Note Please don t change the DIP switch setting when UTP or fiber port is transmitting or receiving data It may cause some data error Besides if you change the DIP switch setting please power off the converter and power on again to make the setting effective AT IMC100T SCSM and 00 5 Fast Ethernet Industrial Media Converters Hardware Description Ports 2 7 Ports RJ 45 ports Auto MDI MDIX The RJ 45 ports auto sensing for 10Base T or 100Base TX devices connections Auto MDI MDIX means that you can connect to another switch or workstation without changing straight through or crossover cabling See figures as below for straight through and crossover cable schematic 2 7 1 RJ 45 Pin Assignments Pin Number Assignement 1 Tx 2 Tx 3 Rx 6 Rx
14. ing Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of circuits might have on overcurrent protection and supply wiring Appropriate consideration of equipment nameplate ratings should be used when addressing this concern amp E21 Caution The unit does not contain serviceable components Please return damaged units for servicing E42 Caution During normal operations the SFP module may have a case temperature that exceeds 70 C 158 F If you remove the module exercise caution when handling with unprotected hands 43 AT IMC100T SCSM and 00 5 Fast Ethernet Industrial Media Converters 20
15. nt of the chassis so that you can easily connect and disconnect the network cables as well as view the unit s LEDs e Air flow around the unit and through the side vents should not be unrestricted e Do not place objects on top of the chassis e Do not expose the device to moisture or water e Make sure that the site is in dust free environment e Use dedicated power circuits or power conditioners to supply reliable electrical power to the network devices e Keep the media converter chassis and the twisted pair cable away from sources of electrical noise such as radios electric motors transmitters broadband amplifiers power lines and fluorescent fixtures 6 2 Installation Steps 6 2 1 Unpack the unit packing 6 2 2 Check the DIN rail clip is screwed on the unit If the DIN rail clip is not screwed the unit please refer to the DIN Rail Mounting section for DIN rail installation If you want to wall mount the unit then please refer to the Wall Mount Plate Fixing section 6 2 3 To hang the unit on the DIN rail track or wall please refer to the Mounting Installation section 6 2 4 Connect Ground Wire to the Ground screw located near the Power Socket 6 2 5 Power on the Unit and the power LED indicator on the unit will light up Please refer to the Wiring the Power Inputs section on how to wire the power Please refer to the LED Indicators section for meaning of LED lights 6 2 6 Prepare the twisted pair straight through
16. port to link down Fiber gt TX If Fiber port link down the media converter will force TX port to link down Switch Architecture Store and Forward Power Input 12 48VDC Redundant power with polarity reverse protection Power Consumption 12 48 VDC Maximum 3 5 W Class 2 50 60 Hz Maximum 3 5 W Class 2 Operating Temperature 40 C to 75 C Operating Humidity 5 to 95 Storage Environment 40 C to 85 C Dimensions Metal case IP 30 30mm W x 140mm H x 95mm D MTBF 810296 hrs Telcordia SR 332 Installation DIN rail and Wall mount design EMC FCC Part 15 Subpart 2012 Class 5003 Issue 5 2012 Class e CAN CSA CISPR 22 10 Class e CISPR 22 2008 Class e AS NZS CISPR 22 2009 A1 2010 Class e ANSI 63 4 2009 EN 61000 6 4 2007 A1 2011 e EN 55022 2010 Class A e EN 61000 3 2 2006 1 2009 A2 2009 Class e EN 61000 3 3 2008 e EN 61000 6 2 2005 e IEC 61000 4 2 2008 e IEC 61000 4 3 2006 A1 2007 A2 2010 e IEC 61000 4 4 2012 e IEC 61000 4 5 2005 e IEC 61000 4 6 2008 e IEC 61000 4 8 2009 e IEC 61000 4 11 2004 e IEC 61000 4 12 2006 AT IMC100T SCSM and 00 5 Fast Ethernet Industrial Media Converters Overview Packing List Safety Industrial Control Equipment UL 508 7th Edition revised Sep 19 2008 and ANSI ISA 12 12 01 2007 Edition For Use in Class I Di
17. s above 3 2 Wall Mount Plate Fixing Follow the steps below to mount the industrial switch with the wall mount plates included Note To remove the DIN Rail clip from the industrial switch unscrew the screws to remove the DIN Rail clip 3 2 1 Place the wall mount plates on the rear panel of the industrial switch 3 2 2 Use the screws to secure the wall mount plates on the industrial switch 3 2 3 Use the hook holes at the corners of the wall mount plates to hang the industrial switch on the wall 3 2 4 To remove the wall mount plates reverse the steps above GREEN CONNECTOR SHOULD BE FACING UP POINTING THE CEILING FIGURE 3 4 Wall Mount Plate Fixing AT IMC100T SCSM and 00 5 Fast Ethernet Industrial Media Converters 16 Cabling Installation Installing Copper Ethernet Cable 4 Cabling Installation 4 1 Installing Copper Ethernet Cable 4 1 1 Insert one side of Category 5 cables into the Ethernet port RJ 45 port and another side of category 5 cables to the network devices Ethernet port RJ 45 port ex switch PC or Server The UTP port RJ 45 LED on the unit will light up when the cable is connected and network is active Please refer to the section LED Indicators for LED light meaning 4 1 2 Connect fiber cabling as explained in paragraph 2 7 2 4 1 3 When all connections are all set and LED lights all show in normal the installation is complete 4 2 Installing SFP Module and Fiber
18. vision 2 Groups A B C and D Hazardous Locations Process Control Equipment CSA C22 2 No 142 M1987 3rd Edition Reaffirmed 2004 and CSA C22 2 No 213 M1987 Non incendive Electrical Equipment for Use in Class I Divi sion 2 Hazardous Locations e 60950 1 2005 2nd Edition Am 1 2009 e EN 60950 1 2006 A 11 2009 A 1 2010 A12 2011 Stability Testing IEC60068 2 32 Free fall IEC60068 2 27 Shock IEC60068 2 6 Vibration 1 3 Packing List I x Industrial 10 100BaseTX 00BaseFX Media Converter I x ATI Product Insert and China RoHS HS TS Substances Concentration Chart 2 x Wall Mounting Bracket and Screws x DIN rail Mounting Bracket and Screws 1 4 Safety Precaution Warning If DC voltage is supplied by an external circuit please use a protection device on the power supply input AT IMC100T SCSM and 00 5 Fast Ethernet Industrial Media Converters Hardware Description Front Panel 2 Hardware Description The Fast Ethernet Industrial Media Converter dimensions 30mm VW x 140mm H x 95mm D 2 1 Front Panel The Front Panel of the Fast Ethernet Industrial Media Converter is shown as follows FIGURE 2 1 Front Panel of the Industrial 10 100TX to 100FX Media Converter 2 2 Top View The top panel of the Fast Ethernet Industrial Media Converter is equipped one terminal block connector with six contacts Warning Please connect Ground Wire to Ground Scr
Download Pdf Manuals
Related Search