User Manual
Contents
1. 1 1 5 MOTORIZED ELECTRIC TABLE User s Manual Notification Dear Users Thank you for your purchase of ET 175 Electric Table Please take time to read our manual carefully before use This guarantees you to make full use of this unit and prolongs the operation life of this unit Precautions If you have detected abnormal heat smoke noise or smell immediately stop using the product In the event of an abnormality turn off the power and disconnect the power plug from the power socket Continuing to use the product may result in electric shock or fire Observe the instructions given below regarding the power cable Be sure to use the supplied or specified power cable Do not modify forcibly bend kink or pull the power cable When disconnecting the power cable from the AC outlet be sure to hold the cable by the plug Pulling the cable may cause wire breakage or shot circuit resulting fire or electric shock Do not connect or disconnect the plug of the power cable to from the AC outlet using wet hands Doing so may result in electric shock Do not touch the product with wet hands while the power cable is connected to the AC outlet Doing so may result in electric shock f the product will not be used for a long period disconnect the power cable from the power source Leaving the cable connected to the power socket for a prolonged period will consume electricity and may result2. X600mm Fuse 2 OCS Hexagonal bolt M10 2pcs with spring washers Hexagonal wrench 4 Preparations 1 Insert the power plug of instrument table in suitable three core power socket ensure that the instrument is well grounded 2 Press the up and down switch the table move up and down 3 Keep on pressing the up and down switch when the instrument table reach the limit position the instrument table will stop automatically This illustrates that the instrument is normal Adjust table to the suitable height and then begin to use 5 Maintenance Daily maintenance 1 Dont store instrument in dusty place 2 When not using the instrument pull out the power plug and apply a dust cover 3 Clean the plastic parts such as chin rest bracket forehead rest bell with soft cloth dipped with soluble detergent or water sterilize with medicinal alcohol Replacing the fuse 1 Pull out the power plug from the power socket 2 Screw off the fuse holder cover with the screwdriver 3 Replace with a new fuse and then fasten the cover 4 The fuse specifications are as follows 110V SA 125V 220V 250 6 Specifications 510mm W X450mm D 660mm 160mm 20Kg body only 4 AC220V 230 240V AC110V 120V 50 6OHZ 220VA Conform to Standard 1 601 1 Class 1 Type B N 1 1 5 MOTORIZED ELECTRIC TABLE LUXVISION not responsible or liable for indirect special or
3. consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoyment or use costs of removal or installation or other consequential damages of whatsoever nature Some states do not allow the exclusion or limitation of incidental or consequential damages Accordingly the above limitation may not apply to you Every effort has been made to ensure the accuracy of this manual However LUXVISION makes no warranties with respect to the documentation and disclaims any implied warranties of merchantability and fitness for a particular purpose LUXVISION Inc shall not be liable for any errors or for incidental or consequential damages in connection with the furnishing performance or use of this manual or the examples herein The information in this document is subject to change without notice 9990 NW 14 Street Suite 105 Doral FL 33172 Telephone 888 334 4640
4. in heating Content ASOMOV FOGG PCS Ss OS e AON 1S ID 1 E IENA E A E EE 1 Name of Parts 220V system Fuse holder 1 Up and down switch 1 Up and down switch Upper and lower the instrument table 2 Support The height is adjustable 3 Base Center symmetry 4 Caster Locking unlocking selectable 5 Spare receptacle Used to supply power for a loaded device 2 Assembly Procedures This section of the manual describes how to assemble ET 175 Instrument Table All parts should be taken with great care out of the packing case before assembly 1 2 Screw off two M10 screws and spring washers at the side of the base Put two foot frames at the two side of the base separately with the caster which have lock towards the up and down switch Aim the two holes on the caster to the screw cap at the side of the base and insert Put the instrument table on the flat ground Screw the M10 screws with spring washers in the screw hole on the base through the hole on the foot frame and fasten with hexagonal wrench Put the work table at the top of the instrument unscrew four M8x20mm bolts with washers with spanner Lift the worktable to aim its screw hole at the assembly hole of the instrument table Put down the worktable refasten the bolt securely with the spanner 3 Accesories Standard table 400mmx
Download Pdf Manuals
Related Search