User`s Manual (For M1-201SA-TR)
Contents
1. IEC60601 1 series for medical electrical equipment In addition all such combination system shall comply with the standard IEC60601 1 and or IEC60601 1 1 harmonized national standard or the combination If in doubt contact a qualified technician or your local representative gt WARNING Detachable Listed Type SJT min No 18 AWG 3 conductor terminating in molded on Listed Hospital Grade parallel blade grounding type attachment plug rated minimum 15 A 125 V Maximum 4 0 m long Making tag provided indicating Grounding reliability can only be achieved when the equipment is connected to an equivalent receptacle marked Hospital Only or Hospital Grade 1 9 Warning Regulatory Statements This equipment has been tested and found to comply with the limits for medical devices in FCC CE and UL60601 1 1st Edition 2006 CAN CSA C22 2 No 601 1 M90 2005 These limits are designed to provide reasonable protection against harmful interference in a typical medical installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to other devices in the vicinity However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to other devices which can be determined by turning the equipment off and on the user is encouraged to try to cor2. C 61000 4 4 pa kV for input output 4 kV for input output hospital environment lines lines 1 kV differential Mains power quality should be Surge 1 kV differential mode IEC 61000 4 5 2 kV common mode mode that of a typical commercial or 2 kV common mode hospital environment Conducted RF IEC 61000 4 6 Radiated RF IEC 61000 4 3 3 Vrms 150 kHz to 80 MHz 3 V m 80 MHz to 2 5 GHz 3V 3 V m Portable and mobile RF commu nications equipment should be used no closer to any part of th e Device including cables than the recommended separation di stance calculated from the equa tion applicable to the frequency of the transmitter Recommended Separation Distance d 1 2 P d 1 2VP 80 MHz to 800 MHz d 2 3VP 800 MHz to 2 5 GHz Where P is the maximum output power rating of the transmitter i n watts W according to the tra nsmitter manufacturer and d is t he recommended separation di stance in meters m Field strengths from fixed RF tr ansmitters as determined by an electromagnetic site survey sh ould be less than the complianc e level in each frequency range Interference may occur in the vi cinity of equipment marked with the following symbol Co Note 1 At 80 MHz and 800 MHz the higher frequency range applies Note 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures
3. Electromagnetic propagation is affected by absorption and reflection from structures objects and people 1 13 Regulatory Statements Continued 2013 Opticis Co Ltd All Rights Reserved Revision 2 6 3 Sep 2013 Opticis Locations Headquarters Opticis Co Ltd 16Fl Kins Tower 8 Sungnam daero 331 beon gil Bundang gu Seongnam si Gyunggi do 463 844 South Korea Te 82 31 719 8033 Fax 82 31 719 8032 www opticis com For order support please contact your Distributor or Reseller For technical support check with the Opticis web site www opticis com or contact techsupp opticis com
4. Manual Contents Manual Contents 1 0 Welcome Product Description 1 1 System Requirements for Setup 1 2 Installation 1 3 Troubleshooting Maintenance Technical Support 1 5 Ti C l amp Product Specifications 1 6 p Warranty Information 1 8 Warning 1 9 Regulatory Statements 1 10 Pictorials Figure 1 Optical DVI Extension Module System 1 1 S h pv i Figure 2 Auto EDID button 1 3 tretc Figure 3 Connection of optical fiber 1 4 User s Manual For M1 201SA TR Doc No OE D130903 201SA Rev2 6 1 0 Manual Contents Welcome Congratulations on your purchase of the Stretch DVI M1 201SA TR Optical DVI Digital Visual Interface Extension Module This manual contains information that will assist you in installing and operating the product Product Description The M1 201SA TR optical DVI module transmits four 4 optical data Red Green Blue and clock and can be extended up to 500 meters 1 640ft over a pair of LC duplex multi mode fibers or four 4 LC simplex multi mode fibers at WUXGA 1920x1200 at 60Hz vertical refresh The EDID Extended Display Identification Data in a display can be read and restored by just plugging once transmitter to the display This Auto EDID programming feature makes the installation of M1 201SA more easy and flexile at any variable resolution display systems For your convenience UXGA EDID would have been done before shipment as a default Shipping Group O M1 201SA TR Opt
5. c Environment Guidance Emissions Test Compliance Electromagnetic Environment Guidance RF Radiated This Device uses RF energy only for its internal function Emissions Group 1 Therefore its RF radiated emissions are very low and are not CISPR 11 likely to cause any interference in nearby electronic equipment RF Conducted This Device is suitable for use in all establishments other than Emissions Class A domestic and those directly connected to a low voltage power CISPR 11 supply network which supplies buildings used for domestic purposes Harmonic Emissions IEC 61000 3 2 casa Voltage Fluctuations Flicker 5 Emissions Gomplies IEC 61000 3 3 Guidance and Manufacturer s Declaration Electromagnetic Immunity This Device is intended for use in the electromagnetic environment specified below The user of the Device should assure that it is used in such an environment Immunity Test IEC 60601 Test Level Compliance Level Electromagnetic Environment Guidance Electrostatic Discharge ESD IEC 61000 4 2 6 kV Contact 8 kV Air 6 kV Contact 8 kV Air Floors should be wood concrete or ceramic tile If floors are covered with synthetic material the relative humidity should be at least 30 Electrical Fast 2 kV for power supply lines 2 kV for power supply lines Mains power quality should be Transient Burst A f that of a typical commercial or IE
6. ceiver Then blue LED ON Step 5 Plug the receiver to the DVI receptacle of display Note Be recommended NOT to use any intermediate cable or adapter between them to avoid undesirable performance degradation Step 6 Connect each LC multi mode fiber one by one as shown in figure 3 Transmitter Receiver oI 73 f 2g m L oN T ie EN ULE 0 rE b as E E x Koy mo ES y k Be Figure 3 Connection of optical fiber Step 7 Makes the PC Power On Step 8 Go to Display Properties in Windows systems and click the tap of Settings Then you can set the right display resolution to meet your display Once you set the right resolution you could see displaying the initial screen at the same resolution as just before you powered on Note If you cannot see the initial screen of the OS system and have skipped the Step 1 and Step 2 you have to follow the Step 1 and Step 2 instructions Step 9 You can see processing to adjust the system screen 1 4 Installation continued Troubleshooting The display displays only black screen Ensure that all plugs and jacks used by external power supplies both Opticis and others are firmly connected Ensure the blue LED ON Ensure that the DVI ports are firmly plugged in to the PC and display Ensure that the transmitter and receiver modules plugged correctly to the PC and display respectively Check if the PC and display are powered on and properly booted Reset t
7. dwidth Supports up to WUXGA at 60Hz or 1 65Gbps bandwidth per graphic channel O0 Fiber optic connection The transmitter and receiver modules of M1 201SA TR have two 2 duplex LC receptacles so as to be connected with two 2 LC duplex multi mode fiber having 62 5 125um or 50 125um core O DDC connection Virtual DDC by Auto EDID programming O Mechanical specifications of transmitter and receiver modules m Dimensions 39mm 15mm 59mm W H D O Environmental Specifications E Operating temperature 0 to 40 C Medical 0 to 50 C General Storage temperature 30 C to 70 C E Operating amp Storage humidity 0 to 85 AC DC Power Adapter General O Power Input AC 100 240V 50 60Hz O Power Output 5 V 1A SMPS DC power Adapter 3A is an option O Cord DC Jack Core is 5 V and outer is GND AC DC Power Adapter Medical O Power Input AC 100 240V 50 60Hz O Power Output 5 V 2A SMPS DC power Adapter O Model name BPM010S05FXX Manufacturer BridgePower Corp 1 6 Product Specifications Product Specifications Label Specification Oo 5V 1 0A Direct Current Operation Condition 0 to 40 Medical Temperature C Operating 0 to 50 General condition Relative humidity 0 85 Atmospheric Pressure 700 1060 hPa Temperature C 30 70 ae Relative humidity 0 85 condition Atmospheric Pressure 500 1060 hPa 1 7 Product Specifications C
8. e orienting or relocating the Device b Over the frequency range 150 kHz to 80 MHz field strengths should be less than 3 V m 1 11 Regulatory Statements 1 12 Regulatory Statements Guidance and Manufacturer s Declaration Recommended Separation Distance Between Portable and Mobile RF Communication Equipment and the Device The Device is intended for use in the electromagnetic environment in which radiated RF disturbances are controlled The user of the Device can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communication equipment transmitters and the Device as recommended below according to the maximum output power of the communications equipment Rated Maximum Output Separation Distance According to Frequency of Transmitter meters Power of Transmitter Watts 150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2 5 GHz d 1 2 P d 1 2 P d 2 3 P 0 01 0 12 0 12 0 23 0 1 0 38 0 38 0 73 1 1 2 1 2 2 3 10 3 8 3 8 7 3 100 12 12 23 For transmitters rated at a maximum output power not listed above the recommended separation distance d in meters m can be estimated using the equation applicable to the frequency of the transmitter where P is the maximum output power of the transmitter manufacturer Note 1 At 80 MHz and 800 MHz the higher frequency range applies Note 2 These guidelines may not apply in all situations
9. he system by de plugging and re plugging the transmitter DVI port or receiver DVI port or by de plugging and re plugging the power cord plugs of transmitter and receiver modules Re boot up the system while connecting the optical DVI extension module Screen is distorted or displays noises Check if the graphic resolution is properly set Go to the display properties of Windows and tap the settings Ensure that the resolution sets less than WUXGA 1920x1200 at 60Hz refresh ratio Reset the system Disconnect and reconnect the optical DVI cables or 5V power adapters Maintenance No special maintenance is required for the optical DVI module and power adapters Ensure that the DVI modules and power adapters are stored or used in a benign environment free from liquid or dirt contamination There are no user serviceable parts Refer all service and repair issues to Opticis Technical Support and Service For commercial or general product support contact your reseller For technical service contact Opticis by email techsupp opticis com or visit its website at www opticis com 1 5 Troubleshooting Maintenance Technical Support Product Specifications M1 201SA TR Optical DVI Extension Modules O Compliance with DVI standard Supports DVI1 0 fully implemented by fiber optic communication and DDC2B by virtual DDC O Extension limit 500m 1 640feet for WUXGA 1920x1200 at 60 Hz refresh rate O Graphic transmission ban
10. ical DVI Extension Module One 1 pair O DC power adapter Two 2 units Oo User s Manual Figure 1 Optical DVI Extension Modules System 1 1 Welcome Product Description System Requirements for Setup O Hardware requirements m You have to have a DVI graphic controller or card having a DVI port in your PC SUN or Mac systems It should support the maximum graphic resolution feature of displays to be connected m No special requirements for memory size CPU speed and chipsets if you ve already properly installed your DVI graphic controllers or cards O Software requirements E No special restrictions if you ve already properly installed your DVI graphic controller in your OS O AC DC Power Adapter Technical Advisory The transmitter Tx module of M1 201SA TR is designed a power protection circuit from conflict of power supply between the external DC power adapter and your graphic card through the DVI pin However the receiver Rx module should be supplied by an AC DC power adapter Tips In general most of laptops or desktop PCs with PCI Express graphic card require using an AC DC power adapter for the transmitter module Note Recommend to use power supplying adapters offered by Opticis which has short circuit break features 1 2 System Requirements for Setup Installation Important Please use the installation procedure below Improper or no operation may result if the start up sequence i
11. ly use the product in the application for which said product is intended Dispose of Old Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product 1 8 Warranty Information gt WARNING Do not touch signal input signal output of other connectors and the patient simultaneously gt WARNING Do not connect any accessory except provided by Opticis Any damage caused other power adapters or accessories will not be taken any responsibility by Opticis Warning for Medical usage gt WARNING External equipment intended for connection to signal input signal output or other connectors shall comply with relevant IEC Standard e g IEC60950 for IT equipment and
12. objects and people lt 5 UT lt 5 UT gt 95 dip in UT gt 95 dip in UT Mains power quality should be l for 0 5 cycle for oa cycle that of a typical commercial or Voltage Dips Short 40 UT 40 U hoscital environment Interruptions and 60 dip in UT 60 dip in UT if io user of the device reatlires Voltage Variations for 5 cycles for 5 cycles continued operation during Bt on Power Supply 70 UT 70 UT i Input Lines 30 dip in UT 30 dip in UT cls ha ee IEC 610004 1 pl Nae 2 coun powered from an uninterruptible gt 95 dip in UT gt 95 dip in UT POMP SOUISE for 5 sec for 5 sec Power Frequency Power frequency magnetic fields 50 60 Hz should be at levels characteristic Magnetic Field FAm SAM of a typical location in a typical IEC 61000 4 8 home or hospital environment a Field strength from fixed transmitters such as base stations for radio cellular cordless telephones and land mobile radios amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which the Device is used exceeds the applicable RF compliance level above the Device should be observed to verify normal operation If abnormal performance is observed additional measures may be necessary such as r
13. ontinued Warranty Information 1 One Year Warranty Opticis warrants this optical DVI extension module to be free from defects in workmanship and materials under normal use and service for a period of one 1 year from the date of purchase from Opticis or its authorized resellers If a product does not work as warranted during the applicable warranty period Opticis shall at its option and expense repair the defective product or part deliver to customer an equivalent product or part to replace the defective item or refund to customer the purchase price paid for the defective product All products that are replaced will become the property of Opticis Replacement products may be new or reconditioned Any replaced or repaired product or part has a ninety 90 day warranty or the reminder of the initial warranty period whichever is longer Opticis shall not be responsible for any software firmware information or memory data of customer contained in stored on or integrated with any products returned to Opticis for repair under warranty or not Warranty Limitation and Exclusion Opticis shall have no further obligation under the foregoing limited warranty if the product has been damaged due to abuse misuse neglect accident unusual physical or electrical stress unauthorized modifications tampering alterations or service other than by Opticis or its authorized agents causes other than from ordinary use or failure to proper
14. rect the interference by one or more of the following measures e Reorient or relocate the receiving device e Increase the separation between the equipment e Connect the equipment into an outlet on a circuit different from that to which the other device s are connected e Consult the manufacturer or field service technician for help e Type of protection against electric shock Class equipment e Degree of protection against electric shock Not classified no applied parts e Classification according to the degree of protection against ingress of water as detailed in the current edition of IEC 529 IPX0 ordinary equipment e This equipment is not suitable for use in the presence of flammable anesthetics or oxygen e Mode of operation continuous operation 1 10 Regulatory Statements Guidance and Manufacturer s Declaration Guidance and Manufacturer s Declaration Electromagnetic Emissions Guidance and Manufacturer s Declaration Guidance and Manufacturer s Declaration Electromagnetic Immunity This Device is intended for use in the electromagnetic environment specified below The user of the Device should assure that it is used in such an environment This Device is intended for use in the electromagnetic environment specified below The user of the Device should assure that it is used in such an environment Immunity Test IEC 60601 Test Level Compliance Level Electromagneti
15. s not correctly followed Step 1 Plug the 5V power adapter to the power jack of the transmitter and connect the adapter to the mains electricity Ensures the blue LED ON Step 2 For Auto EDID programming a Push the Auto EDID button with a narrow pin After twice blinking of Blue LED it will be turned off b Connect the powered transmitter to display while turned on not to the PC The LED blinking indicates reading the EDID LED OFF after blinking notices programming done c Disconnect the transmitter from the display Then LED ON again Figure 2 Auto EDID button Note If you want to change the display please do again the step 2 The default EDID in factory ship out is programmed in the VESA standard of UXGA 60Hz Step 3 Plug directly the transmitter module to DVI receptacle of PC and confirm if the blue LED ON Or connect 5V power adapter to the power jack of the transmitter Note Be recommend NOT to use any intermediate cable or adapter between them to avoid undesirable performance degradation Note If you use laptop or Desktop PC with PCI Express graphic card we recommend using 5V power adapter for the transmitter Note Please DO NOT look directly into the LC receptacles of the Transmitter while it is powered on although this product is regulated strictly enough to operate under the LASER Class I classified by CDRH FDA for eye safety 1 3 Installation Step 4 Connect another 5V power adapter to the re
Download Pdf Manuals
Related Search