Home

Manuals

1. amount of hand lotion Batteries selection suggestion high quality Alkali batteries Void to use low quality and large discharge batteries Woman and children s fingerprint is light suggest to enroll fingerprint of middle finger or thumb GALOP All rights reserved E Focus Industrial Co Ltd info securiticn com 8
2. rapidly The lock will be in the Unlock Mode automatically The lock can be open without any identification StepIII Cancel the Mode repeat StepI the mode cancelled 9 Low battery alert Please change battery if any of the indication appears 1 Press the handle the red light of the front lock lights for 6 seconds 2 After successful identification the red and green light of front lock panel both light for 6 seconds x Appendix 1 Correct pose to place finger Face Side All rights reserved E Focus Industrial Co Ltd info securiticn com E Focus Industrial www vsstr com www securiticn com EH 1 Fingerprint Collector 2 Finger is touching the face of collector quartz glass 2 Incorrect pose All rights reserved E Focus Industrial Co Ltd info securiticn com E Focus Industrial www vsstr com www securiticn com Precaution Before Use please read user manual before use IEI TECH Fingerprint Door Lock 1 The fingerprint collector is quartz glass must be kept clean from the external impact or dirt The fingerprint collector part must be cleaned now and then with a damp cloth to keep the surface clean Mild glass cleaner can be used After placing your finger to unlock the door slide down your fingertip to protect the collector surface from the contamination with dirt It may be difficult to enroll if a finger is very dry Then make the finger moist or little only by rubbing your nose or face or rub in a small
3. rights reserved E Focus Industrial Co Ltd info securiticn com E Focus Industrial www vsstr com www securiticn com Fingerprint identify ztl to register the master fingerprint Three master fingerprints should be registered after finishing the master Step I Press Register button note the button is in the back lock body see x6 then two short Beep sound place master fingerprint to the sensor window for capture the fingerprints move the fingerprints until the light is off And do twice so with the same fingerprints again Step II the system will automatically judge the previous operation is success or fail If one long Beep sound the master fingerprint register completely if three short Beep it means operation is failed The failure reason may be followings 1 the feature of the fingerprints is few 2 the fingerprint places the incorrect position 3 the fingerprint places too light Step III repeat step I II until no response to press Register button it means three master fingerprints are enrolled completely Notice If the master fingerprints are less then 3pcs we should register the new one till the master fingerprints in the lock is not less than 3 pcs or it will be not safe 2 to register the user fingerprints The user fingerprints are enrolled after 3pcs master fingerprints were registered completely Step I Press door handle till the red light of the sensor window is on put the master fingerprint on
4. the sensor till the red light is off If long beep sound it means successful if no response it means failed the system will be power off Step II after the master fingerprints identify successfully press Register immediately then two short Beep put the user fingerprint which you want to register to the sensor window till the red light is off And do twice so with the same fingerprints again if no response it means the identified fingerprint in the step I is not the master fingerprint the system will be off automatically Step HI the system will automatically judge the previous operation is success or fail If one long Beep sound the user fingerprint register completely if three short Beep it means operation is failure The failure reason may be followings 1 the feature of the fingerprints is few 2 the fingerprint places the incorrect position 3 the fingerprint places too light Notice if there are three short beep after press Register button in the step II it means the user fingerprints is enrolled fully x3 to open lock by fingerprint Press the lock handle till the red light of the sensor window is on put the Fingerprint on the sensor window till the red light is off if one long beep it means operation is successful if no response it means the operation is failed the system will be off automatically Notice after the fingerprint matching successfully the system is in the open model press the handle to open loc
5. E Focus Industrial www vsstr com www securiticn com User Manual FL320 Series FL320 Technology Specification Access Fingerprint amp Mechanic Key Fingerprint collector Optical based fingerprint collector Fingerprint collection time lt 0 8s Fingerprint matching lt Is Fingerprint matching type 1 N False acceptance rate FAR lt 0 001 False rejection rate FRR lt 1 Memory capacity 32 64 128users Fingerprint templates Password digits 8 Password capacity 32 users LED low voltage alarm lt 4 2V Operation voltage DC 6V Power 4x 1 5V AA batteries gt 8000 times authentication Operation Temperature 20C 50C Dimension 245Lx154Wx180D mm Net weight 3 0 kg Chapter I Installation 1 Deadblot box position All rights reserved E Focus Industrial Co Ltd info securiticn com E Focus Industrial www vsstr com www securiticn com IN ANAAN Wo DD AN ANANAANS SS EIS ii V X jes a7 39 24 24 So All rights reserved E Focus Industrial Co Ltd info securiticn com E Focus Industrial www vsstr com www securiticn com 2 Illustration 3 Compents Front lock body Fix screws 3 Key hole Five latch electric control mortise bolt 3 Fingerwindows 9 Back lock cover Red LED for low power Anti lock shaft Green LED for Operation 6 Mortise shaft 2 Control cable Chapter II Fast Operation introduction All
6. fully press Delete button six times immediately till one long beep it means operation is successful If no response it means the identified fingerprint in the step I is not the master fingerprint the system will be off automatically x76 Undertake the back lock body Stepl Unscrew the back lock button SteplI Take the back lock cover off Step III Two operation button 16 left one is register button 17 right one is delete button Back view of the lock e Note please unscrew the round base 1 Zinitialize the Lock All rights reserved E Focus Industrial Co Ltd info securiticn com 5 E Focus Industrial www vsstr com www securiticn com Initialize to unload the lock body there is a small hole on the front lock body the initialized button is in the small hole To press this button with the small screwer then one long beep sound initialized operation is finished the fingerprints and codes in the system are cleared 8 Unlock Mode Setting The lock can be settled as Unlock Mode when users need the lock to be open continuously StepI Press the lock handle till the red light of the sensor window is on put the Fingerprint on the sensor window till the red light is off if one long beep it means operation is successful if no response it means the operation is failed the system will be off automatically StepII After the long beep reset Turn out and in the anti lock shaft of the back lock body
7. k if we don t press the handle in 6 seconds the system will be closed automatically x4 to delete the pointed fingerprint Step I Identify the master fingerprint Press door handle till the red light of the sensor window is on put the master fingerprint on the sensor till the red light is off If long beep sound it means successful if no response it means failed the system will be power off automatically Step II after the master fingerprints identify successfully press Delete button immediately the buton is in the back lock body see x6 two short beep put the user fingerprint which will be deleted to the sensor window until the red light of the sensor window is power off If no response it means the identified fingerprint in the step I is not the master fingerprint the system will be off automatically Step HI If one long Beep sound the user fingerprint delete completely if three short Beep it means operation is failed 5 to delete all fingerprints Step I Identify the master fingerprint Press door handle till the red light of the sensor window is on put the master fingerprint on the sensor till the red light is off If long beep sound it means successful if no response it means failed the system will be power off automatically All rights reserved E Focus Industrial Co Ltd info securiticn com 4 E Focus Industrial www vsstr com www securiticn com Step II after the master fingerprints identify success

Manuals

Contents

Download Pdf Manuals

Related Search

Related Contents