Final Secure Lock 11-11-05.pmd
Contents
1. FERNO When it s critical Installation and Users Manual Accessory Kit 082 2072 Secure Lock Storage Brackets For Model 59 Series EZ Glide Evacuation Chairs November 2005 GLO Pub No 234 3340 00 Secure Lock Storage Brackets Disclaimer This manual contains general instructions for the use operation and care of this product The instructions are not all inclusive Safe and proper use of this product is solely at the discretion of the user Safety information s included as a service to the user All other safety measures taken by the user should be within and under consideration of applicable regulations It is recommended that training on the proper use of this product be provided before using this product in an actual situation Retain this manual for future reference Include it with the product in the event of transfer to new users Additional free copies are available upon request from Customer Relations Proprietary Notice The information disclosed this manual 15 the property of Ferno Washington Inc Wilmington Ohio USA Ferno Washington Inc reserves all patent rights proprietary design rights manufacturing rights reproduction use rights and sales use rights thereto and to any article disclosed therein except to the extent those rights are expressly granted to others or where not applicable to vendor proprietary parts O Copyright Ferno Washington Inc All Rights Reserved Ferno2. wheels crosstube of the folded chair in the cradle of the bottom bracket Figure 7 Attach the top bracket with template to the lift bar of the chair see Step 3 Using the Brackets Page 10 for instructions Make sure the bracket is centered on the lift bar Figure 8 two views Secure Lock Storage Brackets gt ear Wheels Crosstube Figure 8 Bracket Template Centered and Latched on Lift Bar Above front view Below side view Release Handle O Ferno Washington Inc 234 3340 00 November 2005 Secure Lock Storage Brackets 8 10 11 12 Hold the template and back of the bracket flush against the wall and tape the s des of the template to the wall as indicated on the template Figure 9 Peel the tape back from the top and bottom ofthe bracket and lift the bracket and chair off the bottom bracket leaving the template taped to the wall Figure 10 Drill the four holes for the fasteners Figure 11 Mount the bracket Figure 12 Verify that the bracket is securely fastened to the wall Ferno Washington Inc 234 3340 00 November 2005 Installation Figure 10 Removing Bracket from Template and Chair from Lower Bracket Figure 12 Mounting Top Bracket Using the Brackets Secure Lock Storage Brackets 4 USING THE BRACKETS 4 1 Securing the Chair in the Brackets l Place the l ft bar n ts lowest position then fold and lock the cha r 2 Ho
3. Align them as evenly as possible 3 Tape the template to the bracket flanges as indicated on the template Figure 2 To ensure accuracy re mark the four mounting points onto the template through the bracket holes Figure 3 Hold the bracket template unit against the installation location on the wall and use a level to make sure the bracket is straight Tape the sides of the template to the wall as indicated on the template Peel the tape back from the flanges of the bracket and lift the bracket off the template Leave the template taped on the wall Drill the holes for the fasteners Figure 4 and mount the bracket Figure 5 Verify the bracket 1s securely fastened to the wall Ferno Washington Inc 234 3340 00 November 2005 Installation Figure 5 Mounting Bottom Bracket Installation 3 6 Mounting the Top Bracket 1 The template for mounting the top bracket s on Page 15 Remove and use the entire page Set the top bracket on the template aligning the holes in the bracket as evenly as possible with the hole markings on the template Tape the template to the bottom edge and top flange of the bracket To ensure accuracy re mark the four mounting points onto the template through the bracket holes Figure 6 Place the lift bar of the EZ Glide Chair in the lowest position then fold the chair and check to make sure 1t is locked With the chair seat facing you stand the rear
4. MANUAL Ferno Washington Inc 234 3340 00 November 2005 To request additional free Installation and Users Manuals contact Ferno Customer Relations Page 12 or visit us at www ferno com Installation Secure Lock Storage Brackets 3 INSTALLATION 3 1 Selecting the Mounting Surface and Fasteners Because of varying conditions of use and the variety of surfaces that might be selected for mounting the brackets Ferno cannot recommend specific mounting fasteners It is the responsibility of the installer to select mounting points and mounting fasteners that are strong enough to support the brackets and chair under all conditions of use If the brackets are to be mounted an ambulance backing plates or other support not supplied may be needed and the fasteners used should be SAE Grade 5 UNC 2 3 2 Selecting a Mounting Location Select a mounting surface strong enough to support the weight of the brackets and chair under all conditions of use The available mounting space must be at least 21 in wide by 42 in high 53 3 cm wide by 106 6 cm high See Figure 1 The height allows clearance for raising the latch handle and the width accommodates the overall width of the chair Do not use these figures to calculate placement of fasteners Follow the mounting instructions and use the templates provided on Pages 13 and 15 3 3 Tools Required Level e Measuring tape Drill e Masking tap
5. Washington Inc 70 Weil Way Wilmington OH 45177 9371 U S A Telephone Free 1 877 733 0911 I le DIOR een 1 937 382 1451 Fax Fie nennen 1 888 388 1349 1 937 382 6569 A A www ferno com O Ferno Washington Inc 234 3340 00 November 2005 Secure Lock Storage Brackets TABLE OF CONTENTS Section Page 1 Safety Information nun 4 LI Wan een een 2 1 2 IMPOR Eurasia 4 1 3 Bloodborne Disease Notice 4 2 About the 6 4 4 4 1 4 5 2 1 Product Description cn 2 2 General Specifications 4 ERA 4 5 Y Installation aria ie 6 9 3 1 Selecting the Mounting Surface and Fasteners 6 3 2 Selecting a Mounting Location 6 3 3 Tools Required unseren 6 3 4 Additional Parts 6 3 5 Mounting the Bottom Bracket 7 3 6 Mounting the Top 8 9 Section Page 4 Using the Brackets u 10 4 1 Securing the Chair In the Brackets 10 4 2 Removing the Chair From the Brackets 10 Se Maintenance simile 11 5 1 Maintenance Schedule 00000000n000000000 11 5 2 Disinfecting and Cleaning 11 5 3 Inspecting the Brackets 11 SA LUDACALON
6. nie 11 Replacement Parts unsre 12 6 1 Parts and Service U S A and Canada 12 6 2 Parts and Service Worldwide 12 A o O 12 7 Limited Warranty 1 12 8 Ferno Customer Relations 12 Bottom Bracket Template 1 1 1 13 Top Bracket Template 15 Illustrations Kit 5 Figure 1 Minimum Mounting Space Required 6 Figure 2 Bottom Template Taped to 7 Figure 3 Re marking Holes on Template 7 Figure 4 Drilling the Mounting Holes 7 Figure 5 Mounting Bottom 7 Figure 6 Re mark Holes on Top Template 8 Figure 7 Chair Resting in Bracket Cradle 8 Figure 8 Bracket Template Centered and Latched on Lift Bar Above front Below side 8 Figure 9 Sides of Template Taped to Wall 9 Ferno Washington Inc 234 3340 00 November 2005 Figure 10 Removing Bracket and Chair from Template 9 Figure 11 Drilling the Mounting Holes 9 Figure 12 Mounting Top 9 Figure 13 Ch
7. air Crosstube Bracket 10 Figure 14 Capturing Lift Bar in Bracket 10 Figure 15 Lift Bar Captured in Bracket Latch 10 Figure 16 EZ Glide Chair Stored in Secure Lock Mount 10 Figure 17 Releasing Chair from Bracket 10 Number Location nina 12 3 Safety Information About the Brackets Secure Lock Storage Brackets 1 SAFETY INFORMATION 1 1 Warning Warning notices indicate a potentially hazardous situation which if not avoided could result in injury or death WARNING Improper use of the brackets can cause injury Use the brackets only for the purpose described in this manual Improper maintenance can cause injury Maintain the brackets only as described in this manual Improper parts can cause injury Use only Ferno parts on the brackets Modifying the brackets can cause injury and damage Use the brackets only as designed by Ferno 1 2 Important Important notices emphasize important usage or maintenance information Important It is the responsibility of the installer to select mounting points and mounting fasteners that will support the chair and brackets under all conditions of use 1 3 Bloodborne Disease Notice To reduce the risk of exposure to bloodborne diseases such as HIV 1 and hepatitis when using the brackets follow the disinfecting and cleaning instruc
8. e Screwdriver Drill bit Pencil or wrench 3 4 Additional Parts Needed Appropriate Mounting Fasteners see Section 3 1 above Important It is the responsibility of the installer to select mounting points and mounting fasteners that will support the chair and brackets under all conditions of use MINIMUM MOUNTING SPACE REQUIRED 21 in 53 3 cm 4 Minimum Horizontal gt Space Required TOP BRACKET 42 in 106 6 cm Minimum Vertical Space Required BOTTOM BRACKET Figure 1 O Ferno Washington Inc 234 3340 00 November 2005 Secure Lock Storage Brackets 3 5 Mounting the Bottom Bracket Important To ensure proper fit of the chair in the brackets the bottom bracket must be mounted before the top bracket Follow installation instructions in this section 3 5 then in Section 3 6 Important An improper installation surface fastener or location can result in an unsatisfactory or unsafe installation Read and follow instructions in Sections 3 1 and 3 2 on Page 6 before beginning your installation The template for mounting the bottom bracket 1s on Page 13 Remove and use the entire page Set the bottom bracket on the template aligning the bottom holes in the bracket with the bottom hole markings on the template Note Because of tolerance variation during manufacture the bracket holes may not align perfectly with the hole markings on the template
9. ers are available upon request by calling 1 800 733 3766 or 1 937 382 1451 8 FERNO CUSTOMER RELATIONS Customer service and product support are important aspects of each Ferno product Please have the serial number of your brackets available when calling Ferno Customer Relations and include it in all written communications For assistance please contact Ferno Customer Relations Telephone 1 877 733 0911 1 937 382 1451 Fax Toll free een 1 888 388 1349 1 937 382 1191 A www ferno com 12 Serial Number Ferno Washington Inc 234 3340 00 November 2005 13 TEMPLATE TO WALL BRACKET TEMPLATE SET BRACKET ON TEMPLATE AND ALIGN HOLES IN BRACKET WITH HOLE MARKINGS ONTEMPLATE Centerline CAREFULLY REMOVE THIS PAGE O FROM THE MANUAL TAPE SIDE OF TEMPLATE TO WALL Bottom Bracket Template THIS PAGE LEFT BLANK INTENTIONALLY 5 Top Bracket Template Y TOP OF TEMPLATE 1 TO BRACKET TEMPLATE WALL I tf TAPE SIDE OF ol TEMPLATE TO WALL Lala 4 El 9 S 3 ON TEMPLATE AND 4 ALIGN HOLES IN BRACKET WITH HOLE MARKINGS ON TEMPLATE 0 2 5
10. gt Lu ae O E gt l 3 1 lt 4 _ I j OF TEMPLATE of
11. lations Page 12 5 2 Disinfecting and Cleaning Disinfect clean and inspect the mount at regular intervals To disinfect the brackets Remove the chair from the brackets and wipe or spray all bracket surfaces with disinfectant Follow disinfectant manufacturer s instructions Ferno recommends inspecting all parts of the brackets as you disinfect them To clean the brackets Use a nonabrasive applicator to clean the brackets with a solution of warm water and a mild detergent Rinse with a clean cloth dampened with clean water Dry with a towel 5 3 Inspecting the Brackets Have your equipment maintenance personnel inspect the brackets regularly following the list at the right If the inspection shows damage or excessive wear replace the bracket s or remove them from service until repair 1s made 5 4 Lubrication The brackets do not require lubrication Ferno Washington Inc 234 3340 00 November 2005 Maintenance Improper maintenance can cause injury Maintain the brackets only as described in this manual Minimum Intervals for Maintenance Disinfecting this page Cleaning this page Inspecting this page Important Disinfectants and cleaners containing bleach phenolics or iodines can damage the brackets Use caution when disinfecting and cleaning with products containing these chemicals MIDE METE INSPECTION CHECKLIST Are all components present Are all nuts a
12. ld the chair with the folded seat facing you and rest the rear wheels crosstube in the cradle of the bottom bracket Figure 13 Figure 15 Lift Bar Captured in 3 Firmly push the lift bar against the lower edge of Bracket Latch the bracket release handle Figure 14 until the handle latch captures the lift bar Figure 15 Press down on the release handle to make sure the y Lift Bar ALAS in Latch capture is complete When secured in both brackets the chair will look like the one Figure 16 4 Verify that the chair s secure n both brackets 4 2 Removing the Chair From the Brackets Raise the red release handle Figure 17 tilt the chair forward and lift it out of the bottom bracket cradle Rear Wheels Crosstube in Cradle al Figure 16 EZ Glide Chair in Storage Brackets Figure 14 Capturing Lift Bar in Bracket Figure 17 Releasing Chair from Bracket 10 Ferno Washington Inc 234 3340 00 November 2005 Secure Lock Storage Brackets 5 MAINTENANCE A WARNING 5 1 Maintenance Schedule The brackets require regular maintenance Set up and follow a maintenance schedule The table at the right represents minimum intervals for maintenance When using maintenance products follow the manufacturers directions and read the manufacturers material safety data sheets You can purchase a recommended disinfectant from your Ferno distributor or Ferno Customer Re
13. nd bolts securely in place Does the release handle function properly Does the release handle spring function properly Are top and bottom brackets securely fastened to the wall 11 Parts Warranty Customer Relations Secure Lock Storage Brackets 6 REPLACEMENT PARTS 6 1 Parts and Service U S A and Canada To order parts the U S A and Canada contact EMSAR the only agent authorized by Ferno to manage service and repair Ferno products EMSAR factory trained technicians use Ferno approved parts and repair procedures EMSAR has a franchise serving you For details phone fax or visit EMSAR s web site 1 800 73 EMSAR Phone 1 937 383 1051 Fax www EMSAR com Internet 6 2 Parts and Service Worldwide To order Ferno parts contact your Ferno distributor Your distributor is the only agent authorized by Ferno to manage service and repair Ferno products WARNING Improper parts and service can cause injury Use only Ferno parts on the brackets WARNING Modifying the brackets can cause injury and damage Use the brackets only as designed by Ferno 6 3 Parts List Description Part 190 1554 Top Bracket ee 090 5852 216 090 5853 7 LIMITED WARRANTY STATEMENT The products sold by Ferno are covered by a limited warranty The actual terms and conditions of the limited warranty and the limitations of liability and disclaim
14. tions in this manual 2 ABOUT THE BRACKETS 2 1 Product Description Accessory Kit 082 2072 contains the Secure Lock Storage Brackets referred to as the bracket s in this manual a two bracket storage system for use with a Model 59 Model 59 T or Model 59 E EZ Glide Evacuation Chair The brackets may be mounted on the wall of an ambulance or building The bottom bracket supports the rear wheel crosstube of the folded chair The top bracket grasps the chair s lift bar A WARNING Improper use of the brackets can cause injury Use the brackets only for the purpose described in this manual 2 2 General Specifications Weight Bracke Only anne 7 716 3 5 kg Brackets Chair Maximum Weight 47 7 16 21 6 kg Maximum combined weight includes chair brackets patient restraints IV Bag Holder Locking Auxiliary Handles and Headrest Assembly Ferno reserves the right to change specifications without notice 2 3 Kit Components A Top Bracket AS CA Bottom Bracket teen Installation and Users Manual Template for Bottom Bracket Page 13 Template for Bracket Page 15 Ferno Washington Inc 234 3340 00 November 2005 Secure Lock Storage Brackets 2 3 Kit Components continued BOTTOM BRACKET Cradle BOTTOM TEMPLATE About the Brackets TOP BRACKET Release Handle 4 TEMPLATE INSTALLATION AND USERS
Download Pdf Manuals
Related Search