C9372 BRAKE LATHE MANUAL - Greg Smith Equipment Sales
Contents
1. 8 Control Panel Assembly 1 9 Micro Switch 1 10 Terminal Hook PG9 1 11 Screw Sleeve 1 12 Flat Washer GB97 12 1 13 Tighten Screw 1 14 Eye Bolt 1 15 Connector 1 16 Flat Washer GB97 06 9 17 Pan Head Cross Recess Screw GB818 M06x08 9 18 Flat Washer GB97 08 3 19 Pan Head Cross Recess Screw GB818 M08x10 3 20 Work Lamp 1 21 Bulb 1 22 Flat Washer GB97 03 4 23 Spring Washer GB93 03 4 24 Pan Head Cross Recess Screw GB818 M03x10 4 25 Arbor 1 26 Sphere Washer 1 27 Nut 1 Spindle Assembly 15 DESCRIPTION REQ D Tapered Roller Bearing GB297 33209 P5 Tapered Roller Bearing GB297 33010 P5 Base Casting Spindle Housing Assembly Spindle Rotary Shaft Oil Seal GB9877 1 B70x95x10 Shaft Sleeve Gear Belt Pulley Tab Washer for Round Nut GB858 45 Woodruff Key GB1099 8x1 1x28 Round Nut GB812 M45x1 5 Copper Bushing 16x22x20 Transmission Bearing 16 14 Lock Bar Assembly 1 15 Set Sleeve 1 16 DC Motor 1 17 Small Belt Pulley 1 18 Large Belt Pulley 1 19 Gear Belt Pulley 1 20 Washer 4 21 Spacer 1 22 Long Copper Column 4 23 Oil Cup 1152 10 1 2 24 Key GB1096 5x56 1 25 Goodyear V Belt A22 4L240 1 26 Gear Belt 1 27 Hex Thin Nut GB6172 M08 4 28 Hex2. 2 Housing Tool Holder L H 3 Spring Extent 2 4 Washer 2 5 Spring Washer 2 6 Dial Micrometer 2 7 Oriented Sleeve 2 8 Shaft Micrometer 2 9 Holder Tool L H 1 10 Holder Tri Insert L H 1 11 Triangle Cutting Tip TPGX1 10308 2 12 Recessed CTSB Head Screw CSTB3 M3 2 13 Slot Pin 4 14 Set Screw 2 15 Set Screw 2 16 Copper Column 2 17 Hex Thin Nut GB6172 M06 2 18 Hex Socket Set Screw with Cone Point GB78 M08x09 2 19 Slotted Set Screw with Cone Point GB71 M05x06 2 20 Square Set Screw with Long Dog Point 0885 6 2 21 Housing Tool Holder R H 1 22 Holder Tri Insert R H 1 23 Holder Tool R H 1 24 Press Plate 1 25 Shield 1 26 Hex Socket Head Cap Screw GB70 M08x65 1 27 Hex Socket Head Cap Screw GB70 M08x25 4 28 Slotted Pan Head Screw GB67 M06x12 2 2 Flat Washer GB97 06 22 Control Panel Assembly WA 23 DESCRIPTION REQ D 1 Control Box 1 2 Nut 1 3 Connector 1 4 Connector PG1 1 1 5 Connector PG9 1 6 Potentiometer 10K2W 2 7 Selector Switch 1 8 Combate Switch with Lamp 1 9 Knob 2 10 Control Panel 1 11 PWM Venation DC Velometer 90DPO4BL 1 12 PWM Venation DC Velometer 180DPO8BL 1 13 Connection Pole KF 45 1 14 Flat Washer GB97 04 12 15 Spring Washer GB93 04 10 16 Hex Socket Button Head Screw GB70 2 M0
3. SAFETY INSTRUCTIONS 1 Read understand and follow the safety and operating instructions found in this manual Know the limitations and hazards associated with operating the machine 2 Eye Safety ear an approved safety face shield goggles or safety glasses to protect eyes when operating the machine 3 Grounding the Machine Machines equipped with three prong grounding plugs are so equipped for your protection against shock hazards and should be plugged directly into a properly grounded three prong receptacle in accordance with national electrical codes and local codes and ordinances A grounding adapter may be used 4 Work Area Keep the floor around the machine clean and free of tools tooling 2 stock scrap and other foreign material and oil grease or coolant to minimize the danger of tripping or slipping We recommend the use of anti skid floor strips on the floor area where the operator normally stands and that each machine s work area be marked off Make certain the work area is well lighted and ventilated Provide for adequate workspace around the machine 5 Guards Keep all machine guards in place at all times when machine is in use 6 Do Not Overreach Maintain a balanced stance and keep your body under control at all times 7 Hand Safety NEVER wear gloves while operating this machine 8 Machine Capacity Do not attempt to use the machine beyond its stated capacity or operations This type of use will reduce the producti
4. Socket Set Screw with Flat Point GB77 M08x16 4 29 Parallel Pin GB119 A6x20 2 30 Flat Washer GB97 10 3 31 Hex Socket Head Cap Screw GB70 M10x30 2 32 Hex Socket Head Cap Screw GB70 M08x20 1 33 Hex Socket Head Cap Screw GB70 M08x25 1 34 Flat Washer GB97 08 8 35 Spring Washer GB93 08 4 36 Hex Nut GB6170 M08 4 37 Hex Bolt GB5782 M08x45 4 38 Bracket 1 39 Spring Washer GB93 10 1 40 Hex Bolt GB5782 Mt1 0x25 1 41 Hex Socket Set Screw with Flat Point GB77 M08x12 1 42 Name Plate 1 43 Rivet for Name Plate GB827 02x05 4 44 Tube Plug 8 1 45 Hex Socket Set Screw with Cone Point GB78 M08x12 1 46 Hex Socket Set Screw with Flat Point GB77 M05x12 1 47 Grounding Label 1 48 Hex Socket Button Head Screw GB70 2 M05x12 1 3 49 Hex Socket Button Head Screw GB70 2 M08x12 17 Cross Feed Feed Slide Assembly DESCRIPTION REQ D 1 Triangle Knob 2 2 Hand Wheel 2 3 Collar Hand wheel 1 4 Decal Collar 1 5 Washer Wavy 8 5 1 6 Belt Pulley Aluminum Alloy 1 7 Spring 2 8 Limited Sleeve 3 9 Hex Socket Set Screw with Flat Point GB77 M06x04 3 10 Cross Feed Screw 1 11 Curtain 1 12 Retainer Curtain 1 13 Hex Socket Button Head Screw GB70 2 M05x12 22 14 Serrated lock washer external teeth GB862 2 05 8 15 Slide Cross 1 16 Spacer 1 17 Hex Thin Nut GB6172 M10 2 18 Flat Washer GB97 10 1 19 Washer 2 20 Hex Socket Set Scr
5. 4x10 4 17 Flat Washer GB97 08 6 18 Hex Head Bolt Full Thread GB5781 M08x20 3 19 Spring Washer GB93 08 3 20 Hex Nut Style 1 170 08 3 21 Flat Washer GB97 03 4 22 Spring Washer GB93 03 2 23 Cross Recessed Pan Head Screw GB818 M03x10 2 24 Cross Recessed Pan Head Screw GB818 M04x14 4 25 Hex Nut Style 1 GB6170 M03 2 26 Cross Recessed Pan Head Screw GB818 M04x20 2 27 Hex Nut Style 1 GB6170 M04 6 24 WIRING DIAGRAM Input AC110 220V 50 60HZ self accommodate Output DC90 180V Combate Switch with Lanp j AO Input DC90V40W 30RPM 1 100 1 Rotor Motor Drum Motor According to Pwer Supply Input DC90 180V 600V 1750RPM 51 h Limit Switc 3 MIT 50DPO BL SV SPEED V Input AC110 50 6097 self accommodate Output 069 25 PART MUMBER DESCRIPTION REQ D 1 C7 01 01 Upper Cover Plate 1 2 C7 01 02 Mat Plate 1 3 C4F 01 01 00 Left Plate 1 4 CAF 01 02 Below Hang Plate 1 5 C4F 01 10 00 Right Plate 1 6 C4F 01 11 Space Plate 1 7 GB5781 M08x20 Hex Head Bolt Full Thread 12 8 GB97 08 Flat Washer 40 9 GB93 08 Spring Washer 20 10 GB6170 M08 Hex Nut Style 1 20 11 GB70 2 M08x40 Hex Socket Button Head Screw 8 26 MACHINE ASSEMBLY ITEM PART MUMBER DESCRIPTION REQ D 1 Main Machine 1 2 GB70 M06x16 Hex Socket Button Head Screw 1 3 GB97 06 Fl
6. C9372 BRAKE LATHE MANUAL The User s Manual is always in place and available for the operator READ THE SAFETY AND OPERATING INSTRUCTIONS THOROUGHLY BEFORE OPERATING THE MACHINE Receiving Shipment Upon taking delivery of your machine carefully inspect the assembly before removing the crating and packing materials If evidence of damage exists contact the shipper immediately Although we are not responsible for damage incurred during transit you will be provided assistance in preparation and filling of any necessary claims CAREFULLY READ THIS MANUAL BEFORE ATTEMPTING TO SET UP OR OPERATE THIS MACHINE Important Note Always have your serial number ready when communicating with us regarding parts or service Keep this manual in a safe place Date Received Serial Number SAFETY FIRST This manual has been prepared for the owner and those responsible for maintenance of this machine Its purpose aside from proper maintenance and operations is to promote safety through the use of accepted practice READ THE SAFETY AND OPERATING INSTRUCTIONS THOROUGHLY BEFORE OPERATING THE MACHINE In order to obtain maximum life and efficiency from your machine follow all the instructions in the operating manuals carefully The specifications put forth in this manual were in effect at the time of publication However owing to our policy of continuous improvement changes to these specifications may be made at any time without obligation
7. ERATING INSTRUCTIONS DISC TRUING 1 Install the dampening band around the outside edge of the disc before installing the disc on the arbor 2 Once the set up for the disc is complete see set up instructions and tightened in place final positioning of the truing attachment can now be made a Turn the cross slide handwheel clockwise until the tool bed is as close to the spindle housing as possible without the bed interfering with the outside edge of the disc It may be necessary to remove the attachment and reposition the clamp stud further out on the bed b Loosen the clamp handle and slide the disc truing attachment right or left so that the disc is centered between the tool bits Tighten the clamp handle being sure the attachment is square to the tool bed Fig 12 Fig 12 C Check each of the tool bits to be sure they are still in serviceable condition If not rotate to next point of the tool bit d Tighten the screw in the slide plate NOTE Be sure tool bit screws are down tight 3 Check to be sure that the Disc Drum switch is in the OFF position and that both of the handwheel knobs are loosened one quarter turn 4 Switch the spindle switch to the ON position turning on the spindle motor 5 Using the cross slide handwheel XN LE locate the tool bits at the inner surface edge and loosen lock knob Figure 13 La 2 HE ad 0 2 5 Fig 13 10 6 Using the barrel mi
8. ING DO NOT use lacquer thinner CAUTION DO NOT attempt to test set up or operate this machine until you are completely familiar with the functions of all the controls and switches WARNING NEVER loosen or attempt to remove arbor with disc or drum mounted WARNING NEVER remove so much material as to reduce the thickness of the disc below the manufacturers recommended minimum WARINING NEVER remove so much material as to increase the inside diameter of the drum beyond that recommended by the manufacturer SPECIFICATIONS Rotor Diameter Capacity 4 24 102mm 610mm Face Width max 5 127mm Thickness max 2 85 73mm Drum Capacity 6 28 152mm 711mm Depth of Cut 9 229mm Spindle Speed Variable 70 320 RPM Disc Feed per Spindle Rev Variable 0 0 026 Omm 0 66mm Drum Feed per Spindle Rev Variable 0 0 026 Omm 0 66mm Maximum Feed Rate per Minute 2 54 64 5mm Feed Motor 40w continuous duty Spindle Motor 600w continuous duty Net Weight 590 lbs 270Kg CONTROLS AND SWITCHES onun SPINDLE SPINDLE RPM 2 4 FEED RATE Fig 1 Spindle Motor Switch Item 1 Figure 1 The spindle motor switch is a two Fig 2 Drum Stop Switch Figure 3 This switch is a micro switch which serves as an automatic shut off of the Drum feed motor In order for power to position toggle switch When switch OFF all power to the spindle motor is shut off When switched ON the spindle moto
9. at Washer 1 4 Control Box 1 5 GB5781 M08x20 Hex Head Bolt Full Thread 3 6 GB6170 M08 Hex Nut Style 1 3 7 GB93 08 Spring Washer 3 8 GB97 08 Flat Washer 6 9 Upper Hang Plate 1 10 JL50D 1 Work Lamp 1 11 GB818 M08x10 Cross Recessed Pan Head Screw 3 27 28
10. ay be required for optimum surface finish 12 Check both surfaces for total clean up 13 If additional material must be removed relocate the tool bits at the inner surface edge and feed in a little depth and repeat until you can get an ideal surface NOTE On not uniformity worn surface discs the side more worn should be machined first Then the two sides should be machined simultaneity So that minimizes the amount of stock removal necessary to clean up DRUM TRUING 1 Install the dampening band around the outside of the drum before installing the 11 drum on the arbor 2 Install the drum on the arbor securely final positioning of the truing attachment can be made a Loosen the lock knob in the slide plate check the tool bit to be sure it is still in serviceable condition If not rotate to next point of the tool bit NOTE Be sure tool bit set screw is down tight b Turn the cross side handwheel clockwise until the tool bed is as close to the spindle housing as possible Turn the feed screw handwheel counter clockwise until the tool bed is as far left as possible According to the diameter of the drum you can reposition the attachment c Loosen the set screws on top of the tool bar and slide the tool bar to the left until the tool bit just contacts the inside of the drum Figure 16 Tighten the clamp handle 3 Check to be sure that the Disc Drum Lip switch is in the OFF position and that both of the han
11. crometers slowly feed the tool bits in until they just contact the disc wear area 0 on the micrometer scale TIGHTEN the lock knobs on the tool holders NOTE Each mark on the micrometer scale equals approximately 0 002 7 With the disc turning slowly rotate the cross slide handwheel counter clockwise until the lip is removed and both tool bits are past the outside edge 8 With the disc turning rapidly rotate the cross slide handwheel clockwise moving tool bits close to the inner lip 9 Slowly turn the cross slide handwheel clockwise until enough of the inner lip is removed to provide clearance for the pad 10 With the spindle motor on and the disc turning feed in each tool bit 0 002 to 0 010 one to five lines tighten the lock knob Figure 14 Fig 14 11 Position the rotor drum select switch on the rotor tighten the knob on the cross slide handwheel and allow the auto feed to run until the tool bits clear the outside edge of the disc Turn off Disc Drum switch and spindle motor Rotate Feed Rotate Speed Diameter of B Ot Roudh Finish Rotor Drum P oug Spindle Turning Turning 8 12 320 240 42 24 24 12 12 16 240 170 36 24 22 12 16 20 170 120 30 18 18 12 NOTE If you cannot get ideal surface you should find the proper speed by yourself NOTE Refer to Speed and Feed RPM charts Figure 15 to find spindle speed and feed speed by rotor diameter Some experimentation m
12. dwheel knobs loosened Wear Area sd one quarter turn 4 Switch the spindle switch to the ON Fig 16 position the spindle motor starts 5 Using the feed slide handwheel locate the tool bit in position 1 6 Using the cross slide handwheel slowly feed the tool bit in until it just contacts the shoe wear area 7 With the drum turning slowly rotate the feed screw handwheel counter clockwise until the lip is removed and the tool bit is past the outside edge 8 Examine the scratch cut making sure it is uniform around the entire circumference of the rotor If the scratch cut is uniform you can do the next step If the scratch cut is not uniform it means that the drum does not install correctly You should turn the power off remove the rotor from the arbor check the mounting adapters and arbor for nicks burrs or chips remount the rotor and repeat the process 9 With the drum turning using the cross slide handwheel feed in the tool bit 0 002 to 0 004 10 Position the rotor drum switch on drum tighten the knob on the portrait slide handwheel then start turning Turn off Disc Drum switch and spindle motor NOTE Refer to Speed and Feed RPM chart Figure 15 to find spindle speed and feed speed Some experimentation may be required for optimum surface finish 11 Check the surface for total clean up 12 If the surface is not ideal relocate the tool bit and feed in a little depth and repeat until we can
13. e chuck with the rotor or drum attached Using the necessary spacers supplied with the brake lathe so you can tighten the nut securely After tightening you are now ready to 8 resurface the rotor or drum SPECIAL NOTE The chuck will work on any brake lathe using a 1 arbor REMOVING CHUCK JAWS Fig 9 The chuck has two jaws t wil be necessary to remove the chuck jaws for cleaning when changing the other jaws referring to figure 9 The jaws are numbered 1 2 3 and it is very important that they are installed into the corresponding numbered slot 1 Reinstall in the order of 1 2 3 counterclockwise see Figure 9 STEP 1 Enter Jaw No 1 in Slot No 1 when scroll is in this position STEP 2 Enter Jaw No 2 in Slot No 2 when scroll is in this position STEP 3 Enter Jaw No 3 in Slot No 3 when scroll is in this position 2 Aslight amount of pressure may be required on each of the jaws to allow them to be installed evenly and correctly 4 gt PARTS INCLUDED WITH THE DELUXE CHUCK 1 chuck with small jaws 2 standard backing plate 5 1 2 138mm 3 wrench 4 large jaw set 3 3 4 5 3 4 95 146mm 5 large backing plate 7 14 183mm 6 small backing plate 4 1 2 114mm Hub Type Disc or Drum Instructions Mount the disc onto the arbor as in Figure 10 Mount the drum onto the arbor as in Nut Spacer Drum Figure 11 Adapte qf Adapter Arbor D _ Fig 11 OP
14. ew with Cone Point 0879 0 1 21 Flat Washer GB97 06 1 22 Knob T Bar 1 23 Shield 1 24 Retainer Shield 1 25 Hex Socket Set Screw with Flat Point GB77 M04x06 1 26 Hex Thin Nut GB6172 M08 4 27 Hex Socket Set Screw with Flat Point GB77 M08x16 4 28 Copper Column 4 29 Parallel Pin GB119 A4x8 2 30 Hex Socket Set Screw with Flat Point GB77 M12x08 2 31 Stud Clamp 1 32 Wiper 1 33 Slide Cross 1 34 Oil Cup JBT7940 5 C M08 2 35 Hex Socket Button Head Screw GB70 2 M06x12 1 36 Bracket Trip 1 19 37 Nut Cross Feed 1 38 Bracket Trip 1 39 Felt Dust Wiper 1 40 Spring Pin Slotted GB879 2 3X16 3 41 Retainer 1 42 Copper Sleeve 1 43 Aluminum Alloy Belt Pulley 1 44 Gear Belt Pulley 1 45 Hex Socket Set Screw with Flat Point GB77 M05x05 2 46 Belt Pulley 2 47 Hex Socket Button Head Screw 0870 5 2 48 Strain Relief Bushing 2 49 Bracket Portrait Motor 1 50 DC Motor 2 51 Gear Belt 1 52 Portrait Screw 1 53 Small Nut 1 54 Cross Recessed Pan Head Screw 8815 0 2 55 Flat Washer GB97 04 4 56 Small Limit Switch 1 57 Hex Nut GB6170 M04 2 58 Spring Washer GB93 04 2 59 Wiring Cover HK10x12 1 60 Wiring Connector PG9 1 61 Motor Cover 1 62 Connector Plate 1 63 Gear Belt 1 64 Woodruff Key GB1099 3x13 2 65 Copper Sleeve 1 1 66 Feed Motor Connector 20 Disc Brake Truer DESCRIPTION REQ D Base Rotor Truer
15. get an ideal surface CARE AND MAINTENANCE 12 Some basic maintenance will assure that it will continue to operate in a satisfactory manner 1 Using a shop cloth remove all of the chips and dust from on and above the lathe do not use air to clean off the machine 2 Apply a thin layer of light weight oil to the arbor taper cones and double radius adapters after each use 3 A light coat of oil should be applied to spindle every month 4 Slide way is factory adjusted and held in place with set screws No adjustment is needed in a short period 5 A light coat of oil should be applied to dovetails every day 6 The screw should be lubricated often HELPFUL HINTS 1 We recommend that you use a scrap disc or drum and practice before beginning an actual job This will avoid any undue pressure or failure while learning 2 Always clean the surfaces that will be contacting the taper cones double radius adapter s or bell clamp s 3 If a disc or drum cannot be installed correctly after having been cleaned and installed properly it may be damaged or bent 4 If in doubt DON T DO IT CAUTION USE REQUIRED OUR CARBIDE TIPS ONLY TRIANGLE CUTTING TIP TPGX110308 Main Assembly 13 ITEM DESCRIPTION REQ D Spindle Assembly Slide Gib Plate Assembly Disc Rotor Attachment Gear Box Peg Hooks NII amp Base Shield Tool Rack
16. r starts The spindle will begin to rotate Disc Drum Switch Item 2 Figure 1 This switch is a three position select switch When the left side of this switch is depressed power is supplied to the Disc feed motor When the right side of the switch is depressed power is supplied to the Drum feed motor When the switch is in the neutral position centered power to both motors is OFF Disc Stop Switch Figure 2 This switch is a two position limit switch which serves as an automatic shut off of the Disc feed motor In order for power to be supplied to the Disc feed motor the limit plate must be away from the switch be supplied to the Drum feed motor the limit plate must be away from the switch Feed Screw Hand wheel Figure 3 This handwheel is used to move the feed slide plate either left or right as Cross Slide Hand wheel Figure 2 This hand wheel is used to move the feed slide plate either in or out as you you face the front of the machine face the front of the machine INSTALLATION INSTRUCTIONS After uncrating check for HIDDEN DAMAGE If any is found CONTACT YOUR CARRIER IMMEDIATELY 1 Lifting WARNING NEVER ATTEMPT TO LIFT THIS MACHINE USING THE SPINDLE OR ANY HANDWHEEL a There is a M12 Eye Bolt in the top of the spindle housing Be sure the eye bolt is down tight b Using the eye bolt as a lifting point place the machine in its predetermined location and secure using the three mounting lugs on
17. stalled EL Fig 6 ARBOR ATTACHMENT The standard arbor mounts quickly to the spindle receptacle using a threaded draw bar and hand wheel Figure 7 1 Insert the arbor threaded hole first into the spindle receptacle at the left end of the spindle housing carefully make mark NOTE Make certain mating surfaces on the arbor and spindle are clean and free of nicks and gouges The smallest nick or scratch can cause incorrect drum or rotor alignment resulting in inaccurate resurfacing WARNING Never loosen or attempt to remove arbor with a disc or drum mounted 2 Turn the draw bar hand wheel until the arbor is drawn up tight NOTE To remove the arbor give the draw bar hand wheel a quick counter clockwise turn to loosen Continued counter clockwise rotation frees the draw bar from the arbor allowing the arbor to be removed from the spindle CHUCK INSTRUCTIONS HUBLESS DISCS AND DRUMS Mount the hubless disc or drum onto the arbor with the chuck Fig 8 Adapter Fig 8 1 Thoroughly clean the surface of the rotor or drum that is to be mounted on the chuck 2 Place the hubless rotor or drum on a clean flat surface Install the rotor or drum onto the chuck by positioning the jaws into the center hole Make sure chuck and rotor or drum is touched completely Make sure the jaws are tight by chuck key CAUTION Remove the chuck key away the chuck 3 According to the rotor or drum select the appropriate adapter Install th
18. the machine base 2 Thoroughly clean the machine using a soft cloth and an approved solvent to remove any preservative coating WARNING DO NOT use lacquer thinner 3 Be sure all switches are in the OFF position CAUTION DO NOT attempt to test or operate this machine until you are completely familiar with the functions of all of the controls and switches DISC TRUING ATTACHMENT mounted in any one of three positions The disc truing attachment can be See Figure 4 depending on the diameter of the disc The maximum travel of the slide in any position is 4 1 Select the appropriate threaded hole in the feed slide plate and screw one end of the clamp stud into it 2 Place one of the slotted holes of the disc attachment over the stud Add the spacer and the washer Figure 5 Secure the attachment using the clamp handle Note Final location of the disc attachment can be made after the disc rotor to be machined has been installed DRUM TRUING ATTACHMENT The drum truing attachment can be mounted in any one of three locations depending on the diameter of the drum 1 Select the appropriate threaded hole in the feed slide plate and screw one end of the clamp stud into it 2 Place the tool bar tube over the clamp stud add the washer and secure SET using the clamp handle Figure 6 C NOTE Final location of the drum Fe Co attachment can be made after the drum c has been in
19. ve life of the machine and could cause the breakage of parts which could result in personal injury 9 Avoid Accidental Starting Make certain the main switch is in the OFF position before connecting power to the machine 10 Careless Acts Give the work you are doing your undivided attention Looking around carrying on a conversation and horseplay are careless acts that can result in serious injury 11 Job Completion If the operation is complete the machine should be emptied and the work area cleaned 12 Disconnect All Power and Air to Machine before performing any service or maintenance 13 Replacement Parts Use only our replacement parts and accessories otherwise warranty will be null and void 14 Misuse Do not use the machine for other than its intended use If used for other purposes we disclaims any real or implied warranty and holds itself harmless for any injury or loss that may result from such use HANDS CLEAR BE SURE TO READ ALL WARNING ALWAYS WEAR SAFETY KEEP LOOSE CLOTHING CUTTING AREA LABELS AND INSTRUCTION MANUAL GLASSES WHEN AWAY FROM ALL AT ALL TIMES PRIOR O ERATION OFTHIS OPERATING THIS MACHINE MOVING PARTS WARNINGS AND CAUTIONS CAUTION Do Not wear gloves while operating this machine WARNING NEVER attempt to lift this machine using the spindle or any hand wheel 3 CAUTION This machine MUST be securely attached to the work surface before attempting to set up or operate WARN
Download Pdf Manuals
Related Search