Όλο τα στοιχεία του προϊόντος σε pdf
Contents
1. INDOOR or outside mode OUTDOOR IRIS SPEED sets the shutter speed 0 to 15 OUTDOOR mode opens another sub menu where you can set the minimum and maximum aperture 5 1 2 EXPOSURE submenu This submenu contains exposure and shutter speed settings EXPOSURE sk AGG III LI IW 4 SENS UP AUTO a 4 BRIGHTNESS maam 56 a D WDR OFF 6 DEFOG OFF l RETURNL RET A All rights reserved AAT Holding sp z 0 0 10 NVAHD 1DN5102V IR 1 users manual ver 1 0 SETTINGS SHUTTER shutter mode control Allows you to choose the automatic mode AUTO the manual mode with adjustable shutter speed m the range of 1 25 1 50000s and ability to enable the DSS function in the range from x2 to x30 and flicker reduction FLK AGC Sets AGC gain Higher gaim make a scene brighter but noise increases It allows to adjust the gain in the range from 0 to 15 SENSUP Digital Slow Shutter function helps to obtain better brighter images in low light by selecting the multiplier of shutter speed in the range from x2 to x30 opens another sub menu BRIGHTNESS sets brightness level in the range from to 100 D WDR this function allows to enable disable wide dynamic range function that enables to observe the scene with different illumination levels After selecting this function there is a submenu to adjust the level in the range from 0 to 8 DEFOG allows you to enable correction functions of image disrupted by the in2. 1f needed repeat the operation with different settings All rights reserved AAT Holding sp z 0 0 15 NVAHD 1DN5102V IR 1 users manual ver 1 0 SETTINGS BLACK DPC allows to correct mask dead pixels Selecting ON and pressing ENTER button opens a submenu which define the size and location of the zone in which the correction is made position POS SIZE then define the compensation level position LEVEL Then select START position and press ENTER button and wait for the end of the operation In the DPC VIEW check the correction effect and 1f needed repeat the operation with different settings RS485 option disabled 5 1 8 ADJUST submenu D It allows to perform additional image adjustment After pressing ENTER the following submenu is dispalyed 1 SHARPNESS AUTO ol 2 MONITOR LGD oll LSC ON 4 VIDEO OUT PAL 9 RETURN RET of SHARPNESS allows to disable OFF and enable AUTO sharpness correction function After selecting AUTO and pressing ENTER next submenu is displayed where it is possible to set the degree of correction and gain ranges for compensation MONITOR corrects the image parameters depending on chosen monitor LCD monitor or CRT monitor After pressing ENTER the submenu is displayed where fine adjustments can be made LSC enables and disables the function of increasing the brightness of the image edge VIDEO OUT chooses a system in which the camera works PAL or NTSC INFORMATION
3. dowels o Allen key o Mounting template If any of the listed equipment has been damaged during transport or if the package is incomplete the contents of package should be packed back m to the original box Please contact your local NOVUS distributor for further assistance 2 MAIN CHARACTERISTIC Mechanical IR cut filter IR operation capability e Horizontal resolution 720p Min illumination from 0 00005 Ix F 1 4 01x with IR on a Lens type varifocal f 2 8 11mm Built in IR illuminator 2 high power LED e Light sensor e 2DNR and 3DNR digital noise reduction WDR wide dynamic range e SENS UP digital slow shutter DSS s BLC back light compensation e HLC high light compensation o DEFOG improves visibility during fog and rain The ability to work in 720p AHD mode and analog 960H mode Stabilization of IR LED current for extending their service life e Other functions 4 motion detection zones 4 privacy zones mirror effect freeze negative image defective pixels correction defining the camera name adjusting the brightness and sharpness o Operation in PAL and NTSC systems OSD menu o Power supply 12VDC All rights reserved AAT Holding sp z o o 5 NVAHD 1DN5102V IR 1 users manual ver 1 0 SPECIFICATION 3 SPECIFICATION Pick up element 1 3 SONY CMOS 1 3 Mpx imager 1280 H x 1024 V 720p 0 25 Ix F 1 4 color mode 1 50 s 0 005 Ix F 1 4 b w
4. By selecting RESET you can restore the factory settings and by selecting NOT SAVE you can exit the menu without saving changes To exit the submenu select RETURN and press ENTER Choosing with left or right button SAVE amp END in the RETURN position saves changes and closes the menu In case of the image failure after connecting camera or video loss due to changes in the menu it is possible to restore the factory settings Following procedure is also recommended when camera menu is not working To restore factory settings 1 Turn the power off and on again 2 If the picture does not appear perform the following sequence of joystick keys press ENTER UP RIGHT press ENTER Successful completing these steps restores factory settings AHD 720p PAL All rights reserved AAT Holding sp z 0 0 9 NVAHD 1DN5102V IR 1 users manual ver 1 0 SETTINGS 5 1 Main menu In order to enter the menu press the joystick button ENTER command The following menu is displayed on the screen a i EXPOSURE BACKLIGHT WHITE BAL EZ _DAY amp NIGHT NR SPEGIAL ADJUST EXIT SAVESEND of I J B ch fe 5 Ar 5 1 1 LENS submenu This submenu allows to set lens parameters MANUAL manual iris lens or fixed iris lens DC auto iris mode DC signal control opens another sub menu MODE FA IRIS SPEED IMIE 3 RETURN RET ofl MODE selects the operating inside mode
5. For camera mode analog 960H in the ADJUST menu there are two additional items MONITOR OUT switches the aspect ratio between 4 3 and 16 9 COMET option disabled All rights reserved AAT Holding sp z 0 0 16 NVAHD 1DN5102V IR 1 users manual ver 1 0 NOTES All rights reserved AAT Holding sp z 0 0 17 NOVUS AAT Holding Sp Z o o ul Putawska 431 02 801 Warszawa tel 22 546 O 700 fax 22 546 0 719 www novuscctv com 2015 04 08 TF T MK
6. G adjustment Horizontal vertical rotation IR LEDs Focus adjustment a Illumination sensor All rights reserved AAT Holding sp z 0 0 7 NVAHD 1DN5102V IR 1 users manual ver 1 0 INSTALLATION 4 INSTALLATION Please familiarize yourself with the device its parameters and methods of mounting before mounting e Put mounting drawing paper to the wall or ceiling and mark drill holes e Drill holes using markings e Drill additional hole for video and power cables e Using mounting screws from the package attach the base of camera to the ceiling wall holding the camera with hand if needed Put video and power cables through a base of camera and a previously drilled hole in the wall ceiling Put the dome cover on the camera holding the camera with hand if needed Put the stopping ring on the dome cover and gently screw it to the base Manually point the camera in a desired direction to obtain a desired scene view Screw the stopping ring firmly holding the camera with hand if needed Adjust zoom and focus if needed using adjustment screws It is recommended to check focus settings in infrared illumination and make correction in color mode to have proper focus in both modes o Make the appropriate camera settings via the OSD menu NOTE It is possible to switch camera into analog 960H mode which is e g compatible with service monitor To change mode tilt the joystick to the left and hold for about 5 s
7. PEN THE UNIT INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS WARNING PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN USER S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER S RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION IMPORTANT SAFEGUARDS AND WARNINGS 1 Prior to undertaking any action please consult the following manual and read all the safety and operating instructions before starting the device 2 Please keep this manual for the lifespan of the device in case referring to the contents of this manual is necessary 3 All the safety precautions referred to in this manual should be strictly followed as they have a direct influence on user s safety and durability and reliability of the device 4 All actions conducted by the servicemen and users must be accomplished in accordance with the user s manual 5 The device should be disconnected from power sources during maintenance procedures 6 Usage of additional devices and components neither provided nor recommended by the producer is forbidden 7 Mounting the device in places where proper ventilation cannot be provided e g closed lockers etc is not recommended since it may lead to heat build up and damaging the devi
8. airs should be conducted only by qualified service personnel Unplug the camera from the power source immediately and contact the proper maintenance department when the following occurs Damages to the power cord or to the plug itself Liquids getting inside the device or exposure to strong mechanical shock Device behaves in a way not described in the manual and all adjustments approved by the manufacturer and possible to apply by user himself seem not to have any effect Camera is damaged Atypical behaviour of the camera components may be seen heard In necessity of repairs attention to using only original replacement parts with their parameters in accordance with those specified by the producer should be paid Non licensed service and non genuine replacement parts may cause fire or electrocution After maintenance activities tests should be run to ensure proper operation of all the functional components of the device Novus AHD cameras are dedicated to work with Novus AHD DVRs Using only Novus products guarantees the highest image quality Connecting Novus AHD cameras to DVRs from other manufacturers may decrease video quality Attention Technical changes reserved without prior notice and printing errors possible All rights reserved AAT Holding sp z 0 0 4 NVAHD 1DN5102V IR 1 users manual ver 1 0 FOREWORD INFORMATION 1 PACKAGE CONTENTS o NVAHD 1DN5102V IR 1 camera e User s manual e A set of screws and
9. ased the product RoHS Directive 2002 95 EC tested 1 accor ding to 2002 95 EC Out of concern for human health protection and friendly environment we assure that our products falling under RoHS Directive regulations regarding the restriction of the use of hazardous substances in electrical and electronic equipment have been designed and manufactured in compliance with the above mentioned regulations Simultaneously we claim that our products have been tested and do not contain hazardous substances whose exceeding limits could have negative impact on human health or natural environment Information The device as a part of professional CCTV system used for surveillance and control is not designed for self installation in households by individuals without technical knowledge The manufacturer is not responsible for defects and damages that result from improper or inconsistent with user s manual installation of the device in the system AL All rights reserved AAT Holding sp z 0 0 2 NVAHD 1DN5102V IR 1 users manual ver 1 0 SAFETY REQUIREMENTS WARNING THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER DEVICE OPERATION YOU ARE KINDLY REQUSTED TO FAMILIRIZE AN YOURSELF WITH THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION WARNING USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT ONLY AUTHORIZED SERVICE PERSONNEL MAY O
10. between 0 100 MODE ALL DAY NIGHT determines whether the function is running all the time or only at night recommended DEFAULT restores default HSBLC settings 5 1 4 WHITE BAL submenu This feature allows to set appropriate color settings using following options ATW auto tracking white balance based on color temperature AWC gt SET this mode enables adaptive setting of white balance In order to obtain the optimum state under the current illumination direct the camera at a sheet of white paper and press ENTER When lighting parameters change e g light bulbs changed to halogen lamps daylight to artificial light etc procedure mentioned above should be repeated AWB auto white balance adjustment MANUAL manual mode settings In case of inappropriate color settings for ATW AWC modes it is possible to set RED and BLUE values manually Color values range from 0 to 100 and are represented by sliders Any change in the color components are instantly applied to the image 5 1 5 D amp N submenu Allows to adjust day night settings Available settings are AUTO EXT COLOR B W AUTO camera switches between night b w and day color mode automatically depending on current illumination conditions Settings are available at following sub menu 1 ANNEE 8 2 D N DELAY E 4 N D CDS METAN 6 N D DELAY MIME E 5 RETURN RET 4 D N CDS and N D CDS sets the illumination threshold that switche
11. ce itself as a consequence 8 Mounting the camera on unstable surface or using not recommended mounts is forbidden Improperly mounted camera may cause a fatal accident or may be seriously damaged itself The camera must be mounted by qualified personnel with proper authorization in accordance with this user s manual All rights reserved AAT Holding sp z 0 0 3 NVAHD 1DN5102V IR 1 users manual ver 1 0 SAFETY REQUIREMENTS 9 Device should be supplied only from a power sources whose parameters are in accordance with those specified by the producer in the camera technical datasheet Therefore it is forbidden to supply the camera from a power sources with unknown parameters unstable or not meeting producer s requirements 10 11 12 13 14 16 17 Signal cables conducting TV or and telemetric signal should be placed in a way excluding the possibility of damaging them by accident Special attention must be paid to cables getting from the camera and connecting the power supply To avoid equipment damage whole TV circuit should be equipped with properly made discharge overload and lightning protection devices Usage of separating transformers 1s advised Electric installation supplying the device should be designed to meet the specifications given by the producer in such a way that overloading is impossible User cannot repair or upgrade the equipment himself All maintenance actions and rep
12. cular area Available masking methods with overlaid color color reversal or tessellation COLOR INV MOSAIC Pressing ENTER after selecting COLOR INV or MOSAIC option will open a new submenu which allows to set the position and size of the zone COLOR sets the color masking available only 1f COLOR option was chosen TRANS allows you to set the degree of transparency mask available only if COLOR option was chosen DEFAULT restores default settings LANGUAGE switches between OSD languages Polish English Russian and others DEFECT allows to adjust parameters used in Dead Pixel Correction function LIVE DPC sets parameters of the defective pixel correction function in real time Selecting ON and pressing ENTER button opens a submenu for setting the gain level and the level of correction 1 LIVE DPG ON I 2 WHITE DPC ON 3 BLACK DPC ON 4 4 RETURN RET A WHITE DPC allows to a correct hot pixels Selecting ON and pressing ENTER button opens a submenu where you can specify the size and location of the zone in which the correction will be made position POS SIZE then define the level of correction and amplification LEVEL and AGC positions and set SENS UP option if camera uses SENS UP position Then select START position and press ENTER cover the lens tightly and press ENTER agam After correcting process the camera returns to the DPC WHITE menu In the DPC VIEW you can check the correction effect and
13. econds To return to the AHD mode tilt the joystick to the right and hold for about 5 seconds The default mode of the camera is AHD mode By pressing and holding the joystick down DN camera switches between PAL and NTSC systems The default operating mode of the camera is PAL 4 1 Power supply connection NOTE Device should be supplied only from a power sources whose parameters are in accordance with those specified by producer in the camera s technical datasheet Therefore it is forbidden to supply the camera from power sources whose parameters are unknown unstable or not meeting the producer s requirements video All rights reserved AAT Holding sp z 0 0 8 NVAHD 1DN5102V IR 1 users manual ver 1 0 SETTINGS 5 SETTINGS The camera has an OSD menu displayed in the foreground of image During normal operation status information can be displayed on the image To navigate menu and make changes please use joystick located on the cable of the camera Joystick 12VDC Power supply m Video To enter the menu press the joystick which sends ENTER command to the device To choose submenu select the UP DOWN UP DN directions If the sub menu contains the symbol that indicates the opportunity to enter to the settings by pressing the ENTER key To change the parameters of selected items press LEFT RIGHT buttons To exit the menu and saves changes select EXIT and next select SAVE amp END
14. fluence of fog rain etc It opens another sub menu that allows you to set the zone and the degree of noise reduction 5 1 3 BACKLIGHT submenu These compensation functions allow to enhance visibility of the objects located in the foreground surrounded by strongly illuminated background BLC or for enhancing visibility of the objects located near the strong light source HSBLC BLC function allows to enhance visibility of the objects located in the foreground surrounded by strongly illuminated background Pressing ENTER button in this mode displays the following menu Submenu presented allows to set the size and location of the area where the BLC function 1s active furthermore it allows to set the sensitivity of the function HSBLC high light compensation function It allows to enhance visibility of the objects located near the strong point light source If a strong point light source appears on the screen function will mask it for effective observation of the scene itself this function is recommended e g to observe car licence plates Selecting HSBLC displays following screen il 2 3 4 5 6 l All rights reserved AAT Holding sp z o o l NVAHD 1DN5102V IR 1 users manual ver 1 0 SETTINGS SELECT allows to select one of the four areas of HSBLC function DISPLAY enables or disables previously selected zone BLACK MASK enables or disables masking area LEVEL adjusts intensity function
15. mode 1 50 s Number of effective pixels Horizontal resolution 0 0005 Ix F 1 4 color mode DSS 0 00005 Ix F 1 4 b w mode DSS 0 Ix IR on b w mode S N ratio gt 52 dB auto manual 1 25s 1 50 000s for AHD and 1 50s 1 50 000s for analog 960H Electronic shutter Digital slow shutter DSS LENS up to 30x Type varifocal f 2 8 11mm F 1 4 Angle of View H 92 32 for AHD 88 30 for analog 960H DAY NIGHT mechanical IR cut filter Switching Mode auto manual Switching Level Adjustment yes Switching Delay 0 60 s OTHER FUNCTIONS lt D English Polish Russian and others Back Light Compensation BLC yes High Light Compensation HLC yes Wide Dynamic Range WDR yes Digital Noise Reduction DNR yes Defog yes Privacy Zones 4 zones Motion Detection 4 zones Image Processing IR ILLUMINATOR LED number mirror effect rotate sharpening 30 m 120 Range INTERFACES Video output INSTALLATION PARAMETERS BNC 1 0 Vp p 75 Ohm Dimensions mm 120 x 98 L 790g vandal proof aluminium in ivory 12 VDC 10 1 5 W 4 5 W IR on 30 C 40 C Power Supply Power Consumption Operating Temperature Degree of protection All rights reserved AAT Holding sp z 0 0 6 NVAHD 1DN5102V IR 1 users manual ver 1 0 SPECIFICATION 3 1 Dimensions alel 3 2 View of the camera layout of the camera items NOV gt EE
16. nu Allows to set additional camera features Pressing ENTER button in this mode displays the following menu D EFFEGT MOTION PRIVACY LANGUAGE DEFECT RS 485 RETURN F 3 4 a 6 d eo All rights reserved AAT Holding sp z 0 0 13 NVAHD 1DN5102V IR 1 users manual ver 1 0 SETTINGS CAM TITLE allows to enter a string of characters that will be displayed on the screen e g as camera title Screen contains mainly alphanumerical characters which may be used m camera s title Select desired character and press ENTER key Currently edited title is visible at the bottom of the screen Line above it contains buttons for editing the title To enable particular functions please highlight them as normal characters and confirm by pressing ENTER Button functions are described below moves character highlight cursor left gt moves character highlight cursor right POS adjusts the position of entered characters CLR erases the whole title END exits title editing menu D EFFECT submenu allows to set additional digital functions FREEZE holds the picture currently displayed MIRROR allows to change viewpoint as MIRROR ROTATE V FLIP NEG IMAGE enables disables displaying negative video image MOTION allows provided that ON option is selected to turn a built in motion detection feature on or off Motion detection may simultaneously be conducted in four independent zones with
17. s the camera from day to night mode and from night to day mode respectively 6 255 and 0 249 D N DELAY and N D DELAY sets the delay between color and b w mode switching and between b w and color mode 0 60s All rights reserved AAT Holding sp z 0 0 12 NVAHD 1DN5102V IR 1 users manual ver 1 0 SETTINGS B W forces continuous black amp white mode Selecting displays following submenu for adjusting additional values 1 BURST 2 IR SMART OFF 3 IR PYM TT 4 RETURN RET l BURST enables disable chrominance signal synchronization IR SMART function ensuring balanced brightness level of the picture during operation with an IR illuminator which prevents overexposure of the objects located close to the camera and its illuminator Entering the function allows to set function area and sensitivity in the same manner as in motion detection menu IR PWM unavailable 5 1 6 NR submenu Allows to make settings for digital noise reduction function Pressing ENTER button in this mode displays the following menu MIDDLE 2 3DNR MIDDLE 3 RETURN RET a 2DNR allows to set the level of noise reduction for static parts of the image available settings OFF LOW MIDDLE HIGH 3DNR allows to set the level of noise reduction variables dynamic parts of the image available settings OFF LOW MIDDLE HIGH NOTE In the 960H analog mode only 2DNR noise reduction is available 5 1 7 SPECIAL subme
18. their size and location selectable by user Detection of motion displays an MOTION DETECTED information superimposed on the screen After selecting ON and pressing ENTER adjust motion detection settings is displayed as depicted below MOTION BH m DE 3 4 5 6 fle 8 TO 0 0 OI On m m D Om m 4 r 2 gt 2 A m 8 Za 0 me SELECT selects the number of the area for further settings DISPLAY turns on off particular area Also allows to set the position and size of the area SENSITIVITY refers to sensitivity COLOR sets the color visualization of motion in a particular area TRANS allows to set the transparency level of visualization ALARM displays submenu where user can set motion visualization mode OFF BLOCK OUTLINE ALL enable or disable displaying MOTION DETECTED information and set its display time 1 15 s Options ALARM OUT and ALARM SIG are inactive DEFAULT restores default settings All rights reserved AAT Holding sp z o o 14 NVAHD 1DN5102V IR 1 users manual ver 1 0 SETTINGS PRIVACY allows to enable by selecting ON privacy zones Part of the screen may be masked using four rectangular zones Selecting ON and pressing ENTER displays a sub menu containing four masks positions PRIVACY oT AY 1 2 3 4 z 6 SELECT selects the number of the area for further settings DISPLAY turns on off parti
19. user s manual NVAHD 1DN5102V IR 1 NVAHD 1DN5102V IR 1 users manual ver 1 0 INFORMATION EMC 2004 108 EC and LVD 2006 95 EC Directives C CE Marking Our products are manufactured to comply with the requirements of the following directives and national regulations implementing the directives Electromagnetic compatibility EMC 2004 108 EC e Low voltage LVD 2006 95 EC with further amendment The Directive applies to electrical equipment designed for use with a voltage rating of between SOVAC and 1000VAC as well as 75VDC and 1500VDC WEEE Directive 2002 96 EC Information on Disposal for Users of Waste Electrical and Electronic Equipment This appliance is marked according to the European Directive on Waste Electrical and Electronic Equipment 2002 96 EC and further amendments By ensuring this product 1s disposed of correctly you will help to prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol on the product or the documents accompanying the product indicates that this appliance may not be treated as household waste It shall be handed over to the applicable collection point for used up electrical and electronic equipment for recycling purpose For more information about recycling of this product please contact your local authorities your household waste disposal service or the shop where you purch
Download Pdf Manuals
Related Search