Home

User Manual - Pdfstream.manualsonline.com

1. If PAPER JAM remains displayed even after the misfeed clearing procedure is performed refer to What Does Each Message Mean on page 6 25 Di1610 Di1610p 6 6 When the Message ORIGINAL DOC JAM Appears 6 6 6 When the Message ORIGINAL DOC JAM Appears If the message shown below appears while scanning an original with the Auto Document Feeder and the machine stops operating a paper misfeed has occurred in the Auto Document Feeder Follow the procedure described below to clear the misfed paper RESSE MiA Automatic paper supply section Error ECAUTION UE ORIGINAL DOC JAM ECAUTION UE OPEN DOC FEED COVER Clearing a Paper Misfeed in Auto Document Feeder 1 Open the Document Feeder Cover Ce _ O o lt 2 Unload the document from the Document Feeder Tray When a Message Appears Di1610 Di1610p 6 19 Chapter 6 When a Message Appears 6 6 6 When the Message ORIGINAL DOC JAM Appears 3 Raise the Auto Document Feeder 4 While turning the document feed knob in the direction of the arrow gently pull out the original 5 Close the Document Feeder Cover 6 Load the documents removed in step 2 back into the tray x Note Replace the document page that was misfed according to the page number indicated in t
2. r n 1 14 1 6 Explanation of Basic Concepts and Symbols 1 15 Paper Feeding coirt iia ita 1 15 Width and Length aicsrgiiiiae da aaa ian 1 16 Paper Orientation iaia 1 16 Di1610 Di1610p i Contents 2 P aut 2 1 Installation Precautions mrrnrrrrir iii 2 2 Installation Site aria ds 2 2 POWEFSOLFCE niro aloni 2 2 Space Requirements cano nnrnnncnnrnnn nc 2 3 2 2 OperationPrecautions riiii in 2 4 Operating Environment conc crac 2 4 Proper Use tia area iii 2 4 Transporting the Machine i 2 5 Care of Machine Supplies i 2 5 2 3 Legal Restrictions on Copying rriiin 2 6 3 1 Available Features erre iii 3 2 3 2 Components and Their Functions rarriniieineinn 3 3 3 3 Parts Names and Their FUNCTIONS nre 3 4 MainiUnit Gani ii 3 4 Inside the Machine i 3 5 Adjusting the Angle of the Copy Tray i 3 6 Options alia a 3 7 3 4 Control Panel erre eee eine 3 8 Names of Control Panel Parts and Their Functions 3 8 Display INdications sisino innan 3 9 3 5 Turning the Machine On Off and the Initial Mode 3 10 Turning the Machine ON Off i 3 10 To turn ON the Machi
3. PRINT REPORT OK YES Yes CONFIGRATION PAGE dk OK YES 7 The following reports and lists can be printed Configuration Page The list of the printer settings is printed PCL Font List The list of fonts can be printed in order to be checked 3 30 Di1610 Di1610p 3 10 Print Area 3 3 10 Print Area Any part of the image within the area indicated below is not copied Amargin 1 4 at full size from the leading edge of the paper A e A margin 1 4 at full size from the trailing edge of the paper B e A margin 1 4 at full size on both sides of the paper C For details on using the copier to print from a computer when the printer controller is installed refer to the User Manual for the printer controller m D o lt A 1 4 at full size B 1 4 at full size cx C 1 4 at full size Vv Paper output direction Before Making Copies Di1610 Di1610p 3 31 Chapter 3 Before Making Copies 3 10 Print Area 3 32 Di1610 Di1610p Making Copies Making Copies Chapter 4 Chapter 4 Making Copies 4 4 1 Making a Basic Copy 4 1 Making a Basic Copy The following procedure describes how to place an original and make a basic copy of it 1 Position the original o Loading Originals on page 3 22 2 Select the paper tray o Se
4. 1 Loadthe paper so that the front side of the paper the side facing up when the package was unwrapped faces up Note The Bypass Tray can be loaded with a maximum of 1 envelope 1 OHP transparency 1 card or 10 sheets of plain paper When a Message Appears Di1610 Di1610p 6 3 Chapter 6 When a Message Appears 6 6 1 When the Message PAPER EMPTY Appears Loading Paper into Tray2 Optional 1 2 Pull out the drawer for Tray2 Remove the drawer cover and then press down on the paper lifting plate until it locks into place TWH Load the paper into the drawer so that the front side of the paper the side facing up when the package was unwrapped faces up TM Attach the drawer cover and then return the drawer for Tray2 to its original position Di1610 Di1610p 6 2 When the Message TONER EMPTY Appears 6 6 2 When the Message TONER EMPTY Appears When toner is about to run out the message shown below appears indicating that the toner is almost empty When this message appears replace the toner cartridge with a new one as soon as possible If you continue making copies printing the toner will be emptied and copies printing can no longer be made lt Toner nearly empty gt TEXT x1 08 1 JIA E LTE TONER t oi x1 00 1 JAIE LTO EMPTY When the toner is e
5. 1 AUTO PANEL RESET y ON OFF am amp YES a Auto Photo D SS A Yes 0 5 1 2 3 4 5 a m amp YES lt Auto Photo D A A A Di1610 Di1610p 5 2 Specifying the Machine Settings 5 Specifying the Setting for ENERGY SAVE MODE 1 Select ENERGY SAVE MODE o Refer to Selecting the MACHINE SETTING Menu on page 5 3 2 Use the 10 Key Pad to specify the desired length of time until the copier enters Energy Save mode 2 ENERGY SAVE MODE y Tip The timer can be set between A 1 min and 240 min e 15min 1 248 OK YES If an incorrect value is entered press the No key and then enter the correct value 2 3 JO LO UCA E ol so 3 Press the Yes key Using the Utility Mode Di1610 Di1610p 5 5 Chapter 5 Using the Utility Mode 5 5 2 Specifying the Machine Settings Specifying the Setting for DENSITY ADF 1 Select DENSITY ADF o Refer to Selecting the MACHINE SETTING Menu on page 5 3 2 Press the and p keys to select either Mode 1 or Mode 2 3 Press the Yes key fi DENSITY ADF y MODE1 MODE2 ae amp YES Auto Photo gt LS A FT A Di1610 Di1610p 5 2 Specifyin
6. Move the lever in the direction of the arrow to release the lock Di1610 Di1610p 6 2 When the Message TONER EMPTY Appears 6 4 Remove the Toner Cartridge from the Drum Cartridge Note When separating the Toner Cartridge from the Drum Cartridge do not tilt the cartridge otherwise toner may spill Do not touch the PC drum under the flap of the Drum Cartridge otherwise decreased image quality may result Do not touch any metal parts of the Drum Cartridge or Toner Cartridge otherwise the units may be damaged by static electricity Chapter 6 When a Message Appears Di1610 Di1610p 6 7 Chapter 6 When a Message Appears 6 6 2 When the Message TONER EMPTY Appears 5 Shake the new Toner Cartridge well 6 Remove the protective cover from the Toner Cartridge x Note Do not touch the developer roller otherwise decreased image quality may result Developer roller 6 8 Di1610 Di1610p 6 2 When the Message TONER EMPTY Appears 6 7 Align the blue parts of the Drum Cartridge and Toner Cartridge and then attach them together 8 Align the tab on the Imaging Cartridge with the rail in the machine and then install the cartridge Note Do not push in the Imaging Cartridge with excessive force if the cartridge is not correctly aligned on the rail otherwise the units may
7. Ratios set using the Zoom V Pressing the V or A key increases or decreases the zoom ratio in and A keys x 0 01 increments The ratio can range from x 0 50 to x 2 00 Full Size This setting makes a copy the same size as the original x 1 00 4 10 Di1610 Di1610p 4 3 Specifying the Zoom Ratio Setting the Zoom Ratio 1 Position the original o Loading Originals on page 3 22 2 Press the Zoom key until the desired fixed ratio is selected o Each press of the Zoom key changes the setting o To specify a zoom ratio other than a fixed ratio press the W and A keys until the desired zoom ratio is specified Pressing these keys change the ratio in x0 01 increments Tip To quickly specify the desired zoom ratio select the nearest fixed ratio and then press the Hed x1 29 t A A B LTD HL LT v Zoom A a A TEXT x1 28 1 AIA B LTo v Zoom A O A W and 4 keys until the desired zoom ratio is specified 3 Make the other necessary settings o Adjusting the Image Density on page 4 12 4 Using the 10 Key Pad enter the number of copies to be made and then press the Start key Di1610 Di1610p Chapter 4 Making Copies Chapter 4 Making Copies 4 4 4 Adjusting the Image Density 4 4 Adjusting the Image Density The image density setting can be adjusted in two broad modes Text
8. JO IE oo 2 8 Press the Yes key lo _ D Q lt Using the Utility Mode Di1610 Di1610p 5 15 Chapter 5 Using the Utility Mode 5 5 3 Setting Up the Paper Sources Specifying the Setting for TRAY SETTING 1 Select TRAY SETTING o Refer to Selecting the PAPER SOURCE SETUP Menu on page 5 12 2 Press the W and A key to select a tray x Note A tray can be selected only if the optional Paper Feed Cassette is installed 3 Press the Yes key 4 Press the and keys to select either FIXED auto tray switching disabled or CONTINUOUS auto tray switching enabled 5 Press the Yes key TRAY SETTING y TRAY 1 de OK YES 7 v Zoom A A Yes FIXED CONTINUOUS a m amp YES lt Auto Photo D A A A Di1610 Di1610p 5 4 Specifying User Management Settings USER MANAGEMENT Menu 5 5 4 Specifying User Management Settings USER MANAGEMENT Menu From the USER MANAGEMENT menu the various functions which must be specified after the drum cartridge is replaced are available USER MANAGEMENT menu No USER MANAGEMENT Description 1 CHANGE D C This function is used to specify when the drum cartridge will need to be replaced Tip For details on
9. NANI 74 Fusing section Error ECAUTION PAPER JAM CAUTION OPEN FRONT COVER CAUTION The area around the Fusing Unit is extremely hot gt Touching any part other than the paper may result in burns Separating section Clearing a Paper Misfeed in the Machine 1 Open the Front Cover 6 16 Di1610 Di1610p 6 5 When the Message PAPER JAM Appears 6 2 Remove the Imaging Cartridge 3 Grab both sides of the paper and then pull it out upward 4 Grab both sides of the paper and then carefully pull out the sheet of H paper 0 Ce _ O o lt When a Message Appears Di1610 Di1610p 6 17 Chapter 6 When a Message Appears 6 6 5 When the Message PAPER JAM Appears O Grab both sides of the paper and then carefully pull the sheet of paper straight upward Grab both sides of the paper and then carefully pull the sheet of paper straight downward 5 Align the tab on the Imaging Cartridge with the rail in the machine and then install the cartridge x Note Do not push in the Imaging Cartridge with excessive force if the cartridge is not correctly aligned on the rail otherwise the units may be damaged 6 Close the Front Cover Tip
10. 5 20 Specifying the Setting for DENSITY PRIORITY 5 21 Specifying the Setting for DENSITY LEVEL A 5 22 Specifying the Setting for DENSITY LEVEL M _ 5 23 Specifying the Setting for OUTPUT PRIORITY 5 24 Specifying the Setting for RESOLUTION eee 5 25 hen a Message 3 6 1 When the Message PAPER EMPTY Appears 6 2 Loading Paper into Tray1 ie 6 3 Loading Paper into the Bypass Tray iii 6 3 Loading Paper into Tray2 Optional i 6 4 6 2 When the Message TONER EMPTY Appears 6 5 Replacing the Toner Cartridge 6 6 6 3 When the Message D C LIFE Appears 6 10 Replacing the Drum Cartridge in 6 10 6 4 When the Message PAPER MISFEED Appears 6 13 Clearing a Paper Misfeed in the Paper TrayS 6 13 6 5 When the Message PAPER JAM Appears 6 16 Clearing a Paper Misfeed in the Machine 6 16 Di1610 Di1610p Contents 6 6 When the Message ORIGINAL DOC JAM Appears 6 19 Clearing a Paper Misfeed in Auto Document Feeder 6 19 6 7 When the Message PAPER SIZE ERROR Appears 6 21 FortTrayli s s Gas AA a
11. 5 Try performing the copy cycle again 6 22 Di1610 Di1610p 6 7 When the Message PAPER SIZE ERROR Appears For the Bypass Tray 1 Remove all paper from the Bypass Tray DN 2 Load the desired paper into the tray 3 Select the setting for the type and size of paper that is loaded o Specifying the Size and Type of Manually Fed Paper on TEXT x1 99 A LTG ReSET NO page 4 5 y FPLAIN OHP CARD a amp YES 4 HLE LTE LGE Er OK YES CUSTOM F 4 Try performing the copy cycle again Di1610 Di1610p 6 23 Ke _ O o lt When a Message Appears Chapter 6 When a Message Appears 6 6 8 When the Message MACHINE TROUBLE Appears 6 8 When the Message MACHINE TROUBLE Appears If the message shown below appears some machine malfunction has occurred Contact your service representative CAUTION Are MACHINE TROUBLE Error SERVICE CALL CHHHH Note When contacting the service representative be sure to inform them of the machine code error code C that was indicated 6 24 Di1610 Di1610p 6 9 What Does Each Message Mean 6 9 What Does Each Message Mean Message Cause Action REMOVE PAPER IN BYPASS TRAY Paper is loaded in the Bypass Tray Remove the paper from the B
12. rre ieri 4 15 Specifying Sonig ein iaia atalanta 4 16 Di1610 Di1610p iii Contents MPT 5 1 Utility Moders acia iia 5 2 5 2 Specifying the Machine Settings ccsecssesseesseeeeeeneeeeseeneeee 5 2 Selecting the MACHINE SETTING MENU 5 3 Specifying the Setting for AUTO PANEL RESET 5 4 Specifying the Setting for ENERGY SAVE MODE 5 5 Specifying the Setting for DENSITY ADF 5 6 Specifying the Setting for DENSITY BOOK 5 7 Specifying the Setting for PRINT DENSITY n 5 8 Specifying the Setting for LCD CONTRAST 5 9 Specifying the Setting for LANGUAGE 5 10 Specifying the Setting for LAMP OFF TIME 5 11 5 3 Setting Up the Paper SOUICES cceseceeeeeeeeseeeeeeeneeeneeeeeeeenes 5 12 Selecting the PAPER SOURCE SETUP Menu 5 12 Specifying the Setting for TRAY1 PAPER 5 13 Specifying the Setting for TRAY SETTING 5 16 5 4 Specifying User Management Settings USER MANAGEMENT Menu cccscesseesseesseeeeseeeeeeseeees 5 17 To select the USER MANAGEMENT meni 5 17 5 5 Specifying Copy Settings rrrii 5 18 Selecting the COPY SETTING MENU 5 19 Specifying the Setting for PAPER PRIORITY
13. 2 Load the paper into the tray so that the front side of the paper the side facing up when the package was unwrapped faces up 3 Slide the paper guides against the edges of the paper O If Legal size paper is installed open the door of Tray1 4 Attach the Bypass Tray in its original position Di1610 Di1610p 3 7 Copy Paper 3 Note Ifpaper with a different size or type is loaded various settings must be specified from the PAPER SOURCE SETUP menu in the Utility mode If the settings are not correctly specified paper size error may occur For details refer to Specifying the Setting for TRAY SETTING on page 5 16 m D o lt Before Making Copies Di1610 Di1610p 3 19 Chapter 3 Before Making Copies 3 3 7 Copy Paper Loading Paper into the Bypass Tray 1 Load the paper so that the front side of the paper the side facing up when the package was unwrapped faces up 2 Slide the paper guides against the edges of the paper di Note When paper is loaded into the Bypass Tray the paper size and type must be specified otherwise paper size error may occur For details refer to Specifying the Size and Type of Manually Fed Paper on page 4 5 3 20 Di1610 Di1610p 3 7 Copy Paper 3 Loading Paper into Tray2 Optional 1 Pull out the drawer for Tray2 Chapter 3 2 Remove
14. 600 x 300 or 600 x 6 RESOLUTION 600 600 x 300 600 x 600 a b amp YES lt Auto Photo D A To _ D 2 Q lt 3 Press the Yes key Using the Utility Mode Di1610 Di1610p 5 25 Chapter 5 Using the Utility Mode 5 5 Specifying Copy Settings 5 26 Di1610 Di1610p When a Message Appears When a Message Appears Chapter 6 Chapter 6 When a Message Appears 6 6 1 When the Message PAPER EMPTY Appears 6 1 When the Message PAPER EMPTY Appears When the currently selected paper tray runs out of paper the message shown below appears and printing cannot continue xXx 4 Error CAUTION PAPER EMPTY t ECAUTION LOAD PAPER KLTD SARRI Paper size Check the paper tray that has run out of paper and then supply paper according to the following procedures Indicator Paper Tray 1 Tray1 2 Tray2 al Bypass Tray 6 2 Di1610 Di1610p 6 1 When the Message PAPER EMPTY Appears 6 Loading Paper into Tray1 1 Remove the Bypass Tray 2 Load the paper in the tray so that the front side of the paper the side facing up when the package was unwrapped faces up 3 Attach the Bypass Tray in its original position Loading Paper into the Bypass Tray Ce _ O o lt
15. KONICA MINOLTA User Manual Di161 o Dit 61 10p Contents Contents UOTI 1 1 We Want You to Be a Satisfied Customer 1 2 For U S A Users FCC Part 15 Radio Frequency Devices 1 2 For Canada Users Interference Causing Equipment Standard ICES 003 ISSUE iivcuatoocndni ira id 1 3 For users in countries subject to Class B regulations 1 3 For users in countries not subject to Class B regulations 1 3 1 2 SAFETY INFORMATION cccccccsscesseesseeesseesseeeneeeeseenseeesseesseeeaeees 1 4 Warning and Precaution Symbols i 1 4 Meaning Of Symbols conc cnn rca rannnnnccnnn 1 4 WARNING sn nated eddie eel ew cli al aie 1 5 CAUTION cri a N E eE EEEE SES 1 6 Precautions for Routine US in 1 7 1 3 Safety Information sssssunsunsennsunsnnrennennnnnnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 1 8 Laser Safety si acideh tea pithy de aida 1 8 Internal Laser Radiation i 1 8 CDRH Regulati n cucuta tr 1 9 For European Users i 1 9 For Denmark Users iii 1 10 For Finland Sweden Users nooo 1 10 F r Norway UsS6fS cimientos 1 11 Laser Safety Label econ date 1 11 Ozone Release i 1 12 Acoustic OT EE scia diano lira 1 12 1 4 DENSA 1 13 What is an ENERGY STAR Product n 1 13 1 5 Explanation of Manual Conventions
16. and Photo Image Density Setting e Text mode The image density can be adjusted either automatically Auto or manually in nine steps O The image density is adjusted automatically according to the original from which a copy is to be made O Manual image density adjustment The image density can be adjusted to one of nine levels To reduce bleed throughs when copying newspapers and magazines press the key to select a lighter setting To reproduce faint colors in brighter parts of the image press the key to select a darker setting Selecting a darker setting could result in a background image being reproduced on the copy while selecting a lighter setting could make the copy image itself too light Select the appropriate level according to your original Photo mode Select Photo when making a copy from an original having large halftone images such as photos Setting the Image Density 1 Position the original O Loading Originals on page 3 22 2 Press the Auto Photo key on the control panel to select the desired q lt Auto Photo D mode A 4 12 Di1610 Di1610p 4 4 Adjusting the Image Density Each press of the Auto Photo key changes the setting as shown at the right If Text mode is selected TEXT is displayed If the Auto setting is selected AT is displayed If Photo mode is selected PHOTO is displayed Note In the Photo mod
17. 2 2 Di1610 Di1610p 2 1 Installation Precautions 2 Space Requirements To ensure easy machine operation supply replacement and maintenance adhere to the recommended space requirements detailed below 20 32 3 4 33 1 2 Unit Inch Note In order to enable easy machine maintenance and replacement of consumables maintain an adequate amount of space around the machine When lifting the machine be sure to grab the handles on the left and right sides from the rear of the machine If the machine is lifted from its front it may become unbalanced and fall Di1610 Di1610p 2 3 Chapter 2 Precaution Chapter 2 Precaution 2 2 2 Operation Precautions 2 2 Operation Precautions Operating Environment The environmental requirements for correct operation of the machine are as follows Temperature 50 F to 86 F with fluctuations of no more than 18 F within an hour Humidity 15 to 85 with fluctuations of no more than 10 within an hour Proper Use To ensure the optimum performance of the machine follow the precautions listed below Never place heavy objects on the Original Glass or subject it to shocks Never open any machine doors or turn off the machine while it is making copies printing as a paper misfeed could result Never bring any magnetized object or use flammable sprays or liquids near the machine Alwa
18. A To _ D Q lt 3 Press the Yes key Using the Utility Mode Di1610 Di1610p 5 9 Chapter 5 Using the Utility Mode 5 5 2 Specifying the Machine Settings Specifying the Setting for LANGUAGE 1 Select LANGUAGE o Refer to Selecting the MACHINE SETTING Menu on page 5 3 2 Press the V and A keys to select the desired language 3 Press the Yes key LANGUAGE rer d OK YES 7 v Zoom A IIS A A Di1610 Di1610p 5 2 Specifying the Machine Settings 5 Specifying the Setting for LAMP OFF TIME 1 Select LAMP OFF TIME o Refer to Selecting the MACHINE SETTING Menu on page 5 3 2 Press the and p keys to select either Mode 1 or Mode 2 8 LAMP OFF TIME y MODE1 MODE2 am amp YES lt Auto Photo D A To _ D Q lt 3 Press the Yes key Using the Utility Mode Di1610 Di1610p 5 11 Chapter 5 Using the Utility Mode 5 5 3 Setting Up the Paper Sources 5 3 Setting Up the Paper Sources From the PAPER SOURCE SETUP menu the various settings for each paper tray can be specified No Name Description 1 TRAY1 PAPER The type and size of paper loaded in Tray1 can be specified The manufacturer s default settings are PLAI
19. CAUTION OPEN FRONT COVER Paper supply section Clearing a Paper Misfeed in the Paper Trays 1 Remove all paper from the Bypass Tray Ce _ O o lt 2 Removethe Bypass Tray When a Message Appears Di1610 Di1610p 6 13 Chapter 6 When a Message Appears 6 6 4 When the Message PAPER MISFEED Appears 3 Remove all paper from Tray1 A Note Do not reuse paper that has been misfed 4 Reload the paper stack in the tray 5 Attach the tray removed in step 2 6 Reload the paper removed in step 1 7 Remove the cover of optional Tray2 and then pull out the drawer 8 Remove all paper from the drawer TH Di1610 Di1610p 6 4 When the Message PAPER MISFEED Appears 6 9 Reload the paper stack into the drawer and then slide the drawer back into the Paper Feed Cassette 10 Open then close the Front Cover Ce _ O o lt When a Message Appears Di1610 Di1610p 6 15 Chapter 6 When a Message Appears 6 6 5 When the Message PAPER JAM Appears 6 5 When the Message PAPER JAM Appears If the message shown below appears during printing and the machine stops operating a paper misfeed has occurred in the machine Follow the procedure described below to clear the misfed paper
20. 3 22 2 Press the Paper key until the tray loaded with the desired paper is TEXT x1 09 1 selected JA p To a Note If paper is loaded into the TEXT x1 08 1 Bypass Tray first remove it A F LGE If Tray1 is selected the paper Paper size and paper type must first be specified For details refer O to Selecting the PAPER A SOURCE SETUP Menu on page 5 12 3 Make the other necessary settings o Specifying the Zoom Ratio on page 4 10 o Adjusting the Image Density on page 4 12 4 Using the 10 Key Pad enter the number of copies to be made and then press the Start key This will start the copy cycle 4 4 Di1610 Di1610p 4 2 Selecting the Paper 4 Specifying the Size and Type of Manually Fed Paper 1 Position the original o Loading Originals on page 3 22 2 Load paper into the Bypass Tray o Loading Paper into the Bypass Tray on page 3 20 3 The message shown at the right appears Press the No key TEXT x1 00 1 AA LTD ReSET NO No C A 4 Press the and keys until the desired paper type is selected FPLAIN OHP CARD S 1 amp YES Tip Pressing the q and keys lt Auto Photo moves E to select the paper type To return to the previous O message press the No C key 5 Press the Yes key Ye
21. Di1610 Di1610p 3 3 Parts Names and Their Functions 3 Options Auto Document Feeder AF 11 No Part Name Description 1 Document Feeder Tray Load the originals to be scanned face up on this tray Up to 50 document sheets can be loaded at one time p 3 23 2 Document Feeder Open when clearing an original that has been misfed p 6 19 Cover Doc Feed Cover 3 Document Guide Plate Slide the guide plate to the size of the originals p 3 23 4 Document Exit Tray Receives originals which have been scanned by the machine Paper Feed Cassette PF 125 No Part Name Description Tray2 Holds up to 500 sheets of paper p 3 21 Di1610 Di1610p 3 7 m D o lt Before Making Copies Chapter 3 Before Making Copies 3 3 4 Control Panel 3 4 Control Panel Names of Control Panel Parts and Their Functions 12 3 4 5 6 7 8 I O Printer Error i n Y ETA La Status No C MEO O 2in1 4 Panel Reset Sort 7 lt Auto Photo L Paper i M i Zoom n A i o 7 1817 16 14 15 14 13 11 12 11 10 9 No Part Name Description 1 Utility key Press to enter Utility mode For details refer to Using the Utility Mode on page 5 1 2 Printer key Press to enter Printer mode For details refer to the User Manual fo
22. Di1610 Di1610p 5 19 Chapter 5 Using the Utility Mode 5 5 5 Specifying Copy Settings Specifying the Setting for PAPER PRIORITY 1 Select PAPER PRIORITY o Refer to Selecting the COPY SETTING Menu on page 5 19 2 Press the and p keys to select either TRAY1 or TRAY2 1 PAPER PRIORITY y TRAY 1 TRAY 2 a amp YES Auto Photo D AA A FT A 3 Press the Yes key 5 20 Di1610 Di1610p 5 5 Specifying Copy Settings 5 Specifying the Setting for DENSITY PRIORITY 1 Select DENSITY PRIORITY o Refer to Selecting the COPY SETTING Menu on page 5 19 2 Press the and p keys to select either AUTO MANUAL 2 D E N S 1 TY P RI 0 RI TY or PHOTO AUTO MANUAL PHOTO a b amp YES a Auto Photo D A To _ D Q lt 3 Press the Yes key Using the Utility Mode Di1610 Di1610p 5 21 Chapter 5 Using the Utility Mode 5 5 5 Specifying Copy Settings Specifying the Setting for DENSITY LEVEL A 1 Select DENSITY LEVEL A o Refer to Selecting the COPY SETTING Menu on page 5 19 2 Press the and p keys to select one of the three print density levels between LIGHT and DARK 3 Press the Yes key DENSI
23. YES lt Auto Photo D A a HLD LTE LGE amp OK YES CUSTOM F a Auto Photo p Pressing the 4 and keys moves E to select the paper size To return to the previous message press the No key Di1610 Di1610p To _ D Q lt Using the Utility Mode Chapter 5 Using the Utility Mode 5 5 3 Setting Up the Paper Sources 5 Using the 10 Key Pad enter the width X of the loaded paper ee 90 216 x o To clear the entered value OK YES yCrt press the No key a Note The paper width can range from 90 mm 3 1 2 to 216 mm 8 1 2 8 9 lt 0 When entering the paper size ff refer to the diagram on the 0 right side of the screen to check which sides of the paper are the width and the length di Tip Enter the value by mm using the 10 key Pad Refer to the conversion rate below 1 inch 25 4 mm 6 Pressthe Yes key 5 14 Di1610 Di1610p 5 3 Setting Up the Paper Sources 5 7 Using the 10 Key Pad enter the length Y of the loaded paper o To clear the entered value press the No key A O i OJO The paper length can range from 140 mm 5 1 2 to 6 356 mm 14 Enter the value by mm using A Tip the 10 key Pad Refer to the conversion rate below 1 inch 25 4 mm X OK YES EN ee 140 356
24. a copy cycle and make necessary settings p 3 8 9 Exposure Lamp This lamp irradiates the document when it is scanned The time until the exposure lamp goes off can be specified For details on specifying the setting refer to Selecting the MACHINE SETTING Menu on page 5 3 10 Original Scales Use to align the original p 3 24 11 Power Switch Use to turn the machine on and off p 3 10 12 USB Port For details refer to the User Manual for the printer controller 13 Parallel Port For details refer to the User Manual for the printer controller 14 Fuser Cover Not used Inside the Machine No Part Name Description Imaging Cartridge Generates the copy image The Imaging Cartridge is constructed of both the Drum Cartridge and the Toner Cartridge set into place Di1610 Di1610p 3 5 m D o lt Before Making Copies Chapter 3 Before Making Copies 3 3 3 Parts Names and Their Functions Adjusting the Angle of the Copy Tray The Copy Tray can be adjusted to one of three angles Adjust the tray to the angle appropriate for the desired application 1 Normal operation standard position 2 When back curled paper is fed out 3 When clearing a paper misfeed or replacing the Drum Cartridge or Toner Cartridge A Note Adjust the Tray Extension and Paper Stopper to fit the size of the paper For Legal size paper lt gt 3 6
25. be damaged Ke _ O o lt 9 Close the Front Cover When a Message Appears Di1610 Di1610p 6 9 Chapter 6 When a Message Appears 6 6 3 When the Message D C LIFE Appears 6 3 When the Message D C LIFE Appears When the drum cartridge has reached the end of its service life the message shown below appears When the message D C LIFE appears replace the drum cartridge with a new one as soon as possible Hae x1 00 i JIAP LTE D C RR Error BA x1 00 i JIA B LTB LIFE A CAUTION Used Drum Cartridges In order to prevent the used Drum Cartridge from dirtying anything keep it in the box 3 Dispose of the used Drum Cartridge according to your local regulations Replacing the Drum Cartridge 1 Open the Front Cover 6 10 Di1610 Di1610p 6 3 When the Message D C LIFE Appears 6 2 Grab the handle of the Imaging Cartridge and then pull it toward you to remove the cartridge Note Since the Imaging Cartridge can easily be damaged by light exposing the cartridge to light for a long period of time will result in decreased image quality 3 Move the lever in the direction of the arrow to release the lock 4 Remove the Toner Cartridge from the Drum Cartridge Co _ O o lt Note When separating the Toner Cart
26. have passed since the last operation was performed Mode 2 When the machine enters Energy Save mode e The factory default setting is Mode 1 Selecting the MACHINE SETTING Menu 1 Press the Utility key MACHINE SETTING appears TEXT x1 00 1 J A E LTC Utility A 2 From the 10 Key Pad press the key 1 to 8 for the MACHINE SETTING function that you wish to set O The MACHINE SETTING functions are as follows 1 AUTO PANEL RESET 2 ENERGY SAVE MODE 3 DENSITY ADF 4 DENSITY BOOk 5 PRINT DENSITY 6 LCD CONTRAST 7 LANGUAGE 8 LAMP OFF TIME Tip To quit changing the machine settings press the No key STOP SETTING appears Press the Yes key to quit changing the settings To _ D Q lt Using the Utility Mode Di1610 Di1610p 5 3 Chapter 5 Using the Utility Mode 5 5 2 Specifying the Machine Settings Specifying the Setting for AUTO PANEL RESET 1 Select AUTO PANEL RESET o Refer to Selecting the MACHINE SETTING Menu on page 5 3 2 Press the and p keys to select either ON or OFF and then press the Yes key If OFF was selected MACHINE SETTING appears again Note If OFF was selected the Auto Panel Reset function is disabled 3 Press the and keys to select the desired time period min 4 Press the Yes key
27. i 6 21 For the Bypass Tray nn n nn nnnnnnnos 6 23 6 8 When the Message MACHINE TROUBLE Appears 6 24 6 9 What Does Each Message Mean sscsssesseeeesseeeensnenenenees 6 25 6 10 When Incorrect Copies Are Produced 6 26 6 11 The machine is not functioning as designed 6 29 7 1 Specifications iiii iaia 7 2 Di1610 Di1610p ca hei ria 7 2 Auto Document Feeder AF 11 i 7 3 Paper Feed Cassette PF 125 7 3 7 2 Care of the Machine ii 74 CICANiNg pi ii alibi iaia eli nel ion eel ii 7 4 HOUSING COVE iia 7 4 Original Gla SS wsie n dai 7 4 Original Pad ie e dea aii 7 5 Control Panel lerse did nicas 7 5 7 3 Function Combination Matrix rin 7 6 Conditions for Combined Functions i 7 6 7 4 Paper Size and Zoom Ratio Tables e 7 7 Paper Size Li Lasi 7 7 Zoom a EAO E EET GG id ai 7 8 8 1 A iene EENEN EEEE 8 2 Di1610 Di1610p v Contents vi Di1610 Di1610p Introduction Introduction Chapter 1 Chapter 1 Introduction 1 1 1 We Want You to Be a Satisfied Customer 1 1 We Want You to Be a Satisfied Customer Thank you for choosing the Di1610 Di1610p This User Manual describes the functions operating procedures precautions and basic troubleshooting for the Di1610 D
28. keep this manual in a handy place near the machine Please read the next section before using this device It contains important information related to user safety and preventing equipment problems Make sure you observe all of the precautions listed in this manual Please note that some parts of the contents of this section may not correspond with the purchased product Warning and Precaution Symbols A WARNING Ignoring this warning could cause serious injury or even death A CAUTION Ignoring this caution could cause injury or damage to property Meaning of Symbols A triangle indicates a danger against which you should take precaution ZN ZA This symbol warns against possible causes of burns A diagonal line indicates a prohibited course of action O mis symbol warns against dismantling the device A black circle indicates an imperative course of action dy Ens symbol indicates you must unplug the device 1 4 Di1610 Di1610p 1 2 SAFETY INFORMATION 1 WARNING e Do not modify this product as a fire electrical shock or breakdown could result If the product employs a laser the laser beam source could cause blindness Donotattemptto remove the covers and panels which have been fixed to the product Some products have a high voltage part or a laser beam source inside that could cause an electrical shock or blindness O Use only the power cord supplied in the package If
29. key 4 16 Di1610 Di1610p Using the Utility Mode 9 Using the Utility Mode Chapter 5 Chapter 5 Using the Utility Mode 5 5 1 Utility Mode 5 1 Utility Mode There are four menus in the Utility mode No Name Description 1 MACHINE SETTING Used to specify settings for the machine s operating environment 2 PAPER SOURCE Used to specify the size and type of paper loaded in Tray1 In addition SETUP auto tray switching can be enabled for each tray 3 USER MANAGEMENT Used to specify settings after the drum cartridge is replaced 4 COPY SETTING Used to specify the default settings for each copy function 5 2 Specifying the Machine Settings From the MACHINE SETTING menu various settings for the machine s operating environment can be specified Refer to the following table for details on each function No Name Description AUTO PANEL RESET Whether the Auto Panel Reset function is disable or the time 0 5 min 1 min 2 min 3 min 4 min or 5 min until the machine is reset after finishing copying printing or after performing the last operation can be selected If the Auto Panel Reset function is enabled all functions are automatically reset to their default settings e The factory default setting is 1 min ENERGY SAVE MODE If the machine performs no operations for a set length of time it will automatically enter the Energy Save mode The length of t
30. key to start feeding and copying the originals from the top page D Di1610 Di1610p 3 23 Chapter 3 Before Making Copies 3 3 8 Loading Originals Placing the Original on the Original Glass The method for positioning the original differs depending on the type of original being used Precautions for Placing the Original on the Original Glass Care should be taken when positioning the following types of originals An original of a non standard size The document size cannot be detected automatically Press the Paper key or the Zoom key and then select the desired paper size p 4 4 or zoom ratio p 4 10 A highly transparent original OHP transparencies translucent paper etc e Place a blank sheet of paper of the same size over the original A book or other three dimensional object e Letthe machine scan the contents of the original with the Original Cover or the Auto Document Feeder raised Do not attempt to push the Original Glass with excessive force as a malfunction could result The maximum load resistance of the Original Glass is 6 1 2 Ib Note While scanning with the Auto Document Feeder or Original Cover open do not look directly at the bright light that may shine through the Original Glass Although the light that shines through the Original Glass is bright it is not a laser beam and therefore is not as dangerous 3 24 Di1610 Di1610p 3 8 Loading Originals 3 Pos
31. the drawer cover and then press down on the paper lifting plate until it locks into place II Before Making Copies 3 Load the paper into the drawer so that the front side of the paper the side facing up when the package was unwrapped faces up TMH ON 4 Attach the drawer cover and then return the drawer for Tray2 to its original position Di1610 Di1610p 3 21 Chapter 3 Before Making Copies 3 3 8 Loading Originals 3 8 Loading Originals Two Ways of Loading the Original The original may be loaded in the Auto Document Feeder or placed directly on the Original Glass Choose the appropriate method according to the type of the original Specific Types of Originals Original Loading Original Type Original Size Auto Document Sheet originals A4 L B5 L A5 L Legal L to Invoice Feeder Weight of originals 9 1 4 Ib to 34 Ib 16 KL FLS e Original width 5 1 2 to 8 1 2 e Original length 5 1 2 to 14 Original Glass Max weight of sheet originals books or Maximum Legal three dimensional objects 6 1 2 lb Loading Originals in the Auto Document Feeder The Auto Document Feeder automatically feeds originals one page after another so that the machine can scan the data on each page After the machine finishes scanning the data the Auto Document Feeder ejects the page into the Exit Tray To ensure the best possible performance of the Auto Document Feeder use only origina
32. to DARK Adjust the setting for DENSITY LEVEL A in the Utility mode p 5 22 Otherwise cancel the Auto density setting and then manually select the desired density setting p 4 12 The density level is set to DARK Press the key and then select a lighter copy density p 4 12 The Original Glass surface is dirty Wipe the Original Glass clean with a soft dry cloth The original is not held tightly against the Original Glass Place the original in position so that it is held tightly against the Original Glass The copy is blurry The paper is damp Change the paper 6 26 Di1610 Di1610p 6 10 When Incorrect Copies Are Produced Symptom Possible Cause Action The copy has dark specks or spots The Original Glass surface is dirty Wipe the Original Glass clean with a soft dry cloth The Original Pad is dirty Wipe the Original Pad clean with a soft cloth dampened with neutral detergent The original is highly transparent Place a blank sheet of paper over the original The original is 2 sided If a thin double sided document is being copied the information on the back side may be reproduced in the copy Press the key and select a lighter copy density Something is sticking to the Original Glass when the Auto Document Feeder is used Wipe the Original Glass clean with a soft dry c
33. up 0 2in1 3 Make the other necessary settings o Selecting the Paper on page 4 4 o Adjusting the Image Density on page 4 12 4 Using the 10 Key Pad enter the number of copies to be made and then press the Start key 4 14 Di1610 Di1610p 4 6 Finishing Copies 4 6 Finishing Copies When printing two or more sets each set can be printed sorted in order Note In order to sort the printed pages the Auto Document Feeder is required Finishing methods Non Sort The copies are stacked on top of each other as they are made e Sort Documents containing multiple pages can be copied and automatically separated into the individual sets lt Copying 1 set gt rid dl lt Copying 3 sets gt lt Copying 3 sets gt ata Di1610 Di1610p 4 15 Chapter 4 Making Copies Chapter 4 Making Copies 4 4 6 Finishing Copies Specifying Sorting 1 Load the originals in the Auto Document Feeder o Loading Originals on page 3 22 Press the Sort key and then check that the indicator lights up S a CAI Note If the Sort indicator is not lit the Non Sort setting is selected Make the other necessary settings o Selecting the Paper on page 4 4 o Specifying the Zoom Ratio on page 4 10 o Adjusting the Image Density on page 4 12 Using the 10 Key Pad enter the number of copies to be made and then press the Start
34. 1610 Di1610p 7 2 Care of the Machine 7 Original Pad gt Wipe the surface of the Original Pad clean with a soft cloth dampened with a mild household detergent N _ ok oO Vox Miscellaneous Control Panel gt Wipe the surface of the Control Panel clean with a soft dry cloth Note Incorrectly cleaning the Control Panel keys may damage them Never use mild household detergent or glass cleaner to clean the Control Panel Di1610 Di1610p 7 5 Chapter 7 Miscellaneous 7 7 3 Function Combination Matrix 7 3 Function Combination Matrix Function Set Last Paper Zoom Density Original Copy Finishing Sis JE 513 e oO es ELL AE E 312 ES o o LL E 2 o E o o a Bila 3 3 N 2 8 y E a elelsli lelel lt el8lslelPlelele Function Set First S S 8 2 5 5 2 a 51213 Paper Manual Paper Selection Tray1 or Tray2 6 O OO O O OJO OJO OOOO Manual Paper Selection Bypass Tray e O O O O0O OJO OJO OJO OO Zoom Fixed Zoom OJO 1O O O O OJO O O O O Optional Zoom ojoje O O O JO OJO OJO OJO Density Auto Density o o o o e Oje OJO OJO OJO Manual Density o0 0 0 oOjO OJoOJOJO OJO Text OjJOJO O OJO e oOjo ojo oJjo Photo O O oJj0O e Q e OJO OJO OJO Original Original Glass O O O O O 0O OJO e Oje Oje Auto Document Feeder oOloj oj ojojojojoje ojojojo Copy Single Sided O O0O O O O OJO OJO e O
35. 1610 Di1610p 7 7 N ok oO lt Miscellaneous Chapter 7 Miscellaneous 7 7 4 Paper Size and Zoom Ratio Tables Zoom Ratios English Sizes Document Paper Size Desired Paper Size Zoom Ratio Ledger 11x14 x 0 82 11x17 279 4 mm x 431 8 mm Legal x 0 72 Foolscap x 0 76 Letter x 0 64 Invoice x 0 50 11x15 11x14 x 0 93 279 4 mm x 381 mm Legal x 0 77 Foolscap x 0 77 Letter x 0 73 Invoice x 0 50 11x14 Legal x 0 77 279 4 mm x 355 6 mm Foolscap x 0 77 Letter x 0 77 Invoice x 0 50 Legal Foolscap x 0 92 8 1 2 x 14 215 9 mm x 355 6 mm Letter x 0 78 Invoice x 0 60 11x17 x 1 21 Foolscap Letter x 0 84 8 1 2 x 13 f 215 9 mm x 330 2 mm Invoice x 0 64 11x17 x 1 29 11x14 x 1 07 Letter Invoice x 0 64 8 1 2 x 11 215 9 mm x 279 4 mm 11x17 x 1 29 11x14 x 1 27 Invoice 11x17 x 2 00 5 1 2 x 8 1 2 139 7 mm x 215 9 mm 11x14 x 1 64 Legal x 1 54 Foolscap x 1 52 Letter x 1 29 7 8 Di1610 Di1610p 7 4 Paper Size and Zoom Ratio Tables Metric Sizes Document Paper Size Desired Paper Size Zoom Ratio A3 A4 x 0 70 297 mm x 420 mm 11 3 4 x 16 1 2 AS x 0 50 B4 x 0 86 B5 x 0 61 A4 A5 x 0 70 210 mm x 297 mm 8 1 4 x 11 3 4 A6 x 0 50 B5 x 0 86 B6 x 0 61 A3 x 1 41 B4 x 1 22 A5
36. 3 Paper key Press to select the paper tray that contains the desired paper 14 lt gt key Press to adjust the image density e Press to specify the various settings 15 Auto Photo key Press to change the image density mode 16 Sort key Press to select the sort function 17 2in1 key Press to select the 2in1 function 18 Status key Press to display each Counter value p 3 28 Display Indications No Display Indication Description 1 Document type Displays the document type currently specified for the image density 2 Zoom ratio Displays the currently specified zoom ratio 3 Number of copies Displays the currently specified number of copy pages and number of copy sets 4 Image density Displays the currently specified image density 5 Paper Displays the currently selected paper tray paper size and paper type Di1610 Di1610p 3 9 m _ Q lt Before Making Copies Chapter 3 Before Making Copies 3 3 5 Turning the Machine On Off and the Initial Mode 3 5 Turning the Machine On Off and the Initial Mode Turning the Machine On Off To turn on the machine Press the on side of the Power Switch To turn off the machine gt Press the O off side of the Power Switch Note Do not turn off the machine while a copy cycle is being performed as a paper misfeed will result Before attempting to turn off
37. 4 Positioning a Sheet Original ii 3 25 Positioning Highly Transparent Originals 3 26 Positioning Books iu lc A iets 3 27 3 9 Checking the Machine Status rriin 3 28 Checking the Machine Status ii 3 28 Checking the TOTAL PAGE Counts n 3 28 To output a report liSt cece eseeeeeeeeeneeteaeeteeeeeeteeeeaee 3 30 Configuration Page i 3 30 PCL Font Listini iii 3 30 3 10 Print Area ine 3 31 M 4 1 Making a Basic COPY ssceseceseeeeeeeseeeeeeeeeeeeeseeenseeseeeseseeseeeeseenees 4 2 4 2 Selecting the Paper cssccssecseecsseesseessseesseeesseesseessseeseseesseeees 4 4 Manual Paper Selection i 4 4 Selecting Manually Fed Paper i 4 4 Manually Selecting the Paper SIZe i 4 4 Specifying the Size and Type of Manually Fed Paper 4 5 4 3 Specifying the Zoom Ratio rriiiiiiine 4 10 Zoom Ratio Settings ii 4 10 Setting the Zoom Rati0 i 4 11 4 4 Adjusting the Image DENSItY rrrrrrriiere iii riinne 4 12 Image Density Setting i 4 12 Setting the Image Density nana nancnnnos 4 12 4 5 Making 2in1 COpieS rii iii 4 14 Specifying Settings for 2in1 COpieS i 4 14 4 6 Finishing Copies
38. A6 x 0 70 148 mm x 210 mm 5 3 4 x 8 1 4 B6 x 0 86 A4 x 1 41 A3 x 2 00 B4 x 1 73 B5 x 1 22 A6 A4 x 2 00 105 mm x 148 mm 4 1 4 x 5 3 4 AS x 1 41 B5 x 1 73 B6 x 1 22 B4 A4 x 0 81 257 mm x 364 mm 10 x 14 1 4 AS x 0 57 B5 x 0 70 B6 x 0 50 A3 x 1 15 B5 A5 x 0 81 182 mm x 257 mm 7 1 4 x 10 A6 x 0 57 B6 x 0 70 A3 x 1 64 A4 x 1 15 B4 x 1 41 Di1610 Di1610p 7 9 N jo E ok oO E Miscellaneous Chapter 7 Miscellaneous 7 7 4 Paper Size and Zoom Ratio Tables B6 A6 x 0 81 128 mm x 182 mm 5 x 7 1 4 A4 x 1 64 A5 x 1 15 B4 x 2 00 B5 x 1 41 Zoom ratio Paper size Document size 1 inch 25 4 mm 1 mm 0 0394 inch 7 10 Di1610 Di1610p Index Index Chapter 8 Chapter 8 Index 8 8 1 Index 8 1 Index LIO COI aiii cee eis eee eee 4 14 PAULO ia 3 13 Auto COPY Stalin dto ta 3 13 Auto document feeder AF 11 i 7 3 Auto Paneles acc riada T 3 12 A totray SWItehINg ras etaa lada aida 3 13 Basic copy operation reee 4 2 Care ofthe Machine ais c5sis case a aae aaa ara aa TE ae ane aaia aaa 7 4 Gontrol panel rriastuota toi aio a ted lec tel te 3 8 Copy Paper siii iI dis el a o de a 3 14 Copy Settings vatios aa 5 18 Copy tray Angle elia asa 3 6 Default SettiNgs cti de aaa ee ao 3 11 Energy save MOde A 3 12 Finishing COPOS uc alii AA 4 15 Function combination Mat
39. Card NC 5 option e By installing the Network Interface Card NC 5 into this machine network printing from Windows or a NetWare network environment is possible Network Interface Card can be installed only onto Di1610p Di1610 Di1610p 3 3 m _ D gt o lt Before Making Copies Chapter 3 Before Making Copies 3 3 3 Parts Names and Their Functions 3 3 Parts Names and Their Functions Main Unit No Part Name Description 1 Original Cover Holds the original against the Original Glass 2 Original Glass Place your original on this glass to allow the machine to scan it The original is to be placed face down p 3 24 3 4 Di1610 Di1610p 3 3 Parts Names and Their Functions No Part Name Description 3 Front Cover Open when replacing the Toner Cartridge or Drum Cartridge or clearing a paper misfeed p 6 5 4 Tray1 Holds up to 250 sheets of paper and easily adjusts to different paper sizes Special paper can be used p 3 14 5 Bypass Tray Use for manual feeding of paper Holds up to 10 sheets of paper Special paper can be used p 3 20 6 Tray1 door If Legal size paper is installed open this door 7 Copy Tray Holds copies fed out face down from the machine The Copy Tray can be adjusted to one of three angles Adjust the Copy Tray to the angle appropriate for its application p 3 6 8 Control Panel Use to start
40. Di1610p 1 7 Chapter 1 Introduction Chapter 1 Introduction 1 1 3 Safety Information 1 3 Safety Information Laser Safety This is a digital machine which operates using a laser There is no possibility of danger from the laser provided the machine is operated according to the instructions in this manual Since radiation emitted by the laser is completely confined within a protective housing the laser beam cannot escape from the machine during any phase of user operation This machine is certified as a Class 1 laser product In other words the machine does not produce hazardous laser radiation Internal Laser Radiation Maximum Average Radiation Power 36 903 uW at the laser aperture of the print head unit Wavelength 770 800 nm This product employs a Class 3b laser diode that emits an invisible laser beam The laser diode and the scanning polygon mirror are incorporated in the print head unit The print head unit is NOT A FIELD SERVICEABLE ITEM Therefore the print head unit should not be opened under any circumstances Print Head 1 8 Di1610 Di1610p 1 3 Safety Information 1 Laser Aperture of the Print Head Unit There is a laser aperture at the location shown above which must NEVER be viewed directly by the user CDRH Regulation This machine is certified as a Class 1 Laser product under Radiation Performance Standard according to the Food Drug an
41. ECT T C TYPE t CHANGE T C Incorrect type of toner cartridge is installed Install the correct type of toner cartridge p 6 5 Toner cartridge is not installed Install the toner cartridge p 6 6 TEXT X1 00 1 ADD XXX EMPTY While specifying copy settings The selected paper tray has run out of paper indicates the paper tray and XXX indicates the paper size Either load paper of the specified size into the specified paper tray or press the Paper key and select a different paper size Di1610 Di1610p 6 25 Ce _ O Q lt When a Message Appears Chapter 6 When a Message Appears 6 6 10 When Incorrect Copies Are Produced 6 10 When Incorrect Copies Are Produced Symptom Possible Cause Action The image is too light The density level for the Auto setting is set to LIGHT Adjust the setting for DENSITY LEVEL A in the Utility mode p 5 22 Otherwise cancel the Auto density setting and then manually select the desired density setting p 4 12 The density level is set to LIGHT Press the key and then select a darker copy density p 4 12 Does the message TONER EMPTY appear in the Display Change the Toner Cartridge with a new one p 6 6 The paper is damp Change the paper The image is too dark The density level for the Auto setting is set
42. N and Letter L 2 TRAY SETTING Whether or not auto tray switching is enabled for each paper tray can be specified p 3 13 e The factory default setting is CONTINUOUS Selecting the PAPER SOURCE SETUP Menu 1 Press the Utility key twice RARE PAPER SOURCE SETUP d OK YES or1 2 7 Utility A 2 From the 10 Key Pad press the key 1 or 2 for the PAPER SOURCE SETUP function that you wish to set Oo The PAPER SOURCE SETUP functions are as follows 1 TRAY1 PAPER 2 TRAY SETTING A Tip To quit setting up the paper sources press the No key STOP SETTING appears Press the Yes key to quit changing the settings Di1610 Di1610p 5 3 Setting Up the Paper Sources Specifying the Setting for TRAY1 PAPER 1 Select TRAY1 PAPER o Refer to Selecting the PAPER SOURCE SETUP Menu on page 5 12 2 Pressthe and Keys until the type of paper loaded is selected 3 Press the Yes key 4 Press the and keys or press the W key to select the size of paper that is loaded If CUSTOM is not selected continue with step 8 o If CUSTOM is selected perform steps 5 through 8 Note If OHP was selected in step 3 the only paper sizes that can be loaded are Letter L and A4 L Tip 1 TRAY1 PAPER y CARD E i OHP 1 amp
43. OMPLIES WITH 21 CFR CHAPTER I SUBCHAPTER J For Other Area CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUKT E451 HOM AS PRODUCTO LASER DE CLASE 1 Di1610 Di1610p 1 11 Chapter 1 Introduction Chapter 1 Introduction 1 1 3 Safety Information Ozone Release NOTE Locate the Machine in a Well Ventilated Room A negligible amount of ozone is generated during normal operation of this machine An unpleasant odor may however be created in poorly ventilated rooms during extensive machine operations For a comfortable healthy and safe operating environment it is recommended that the room be well ventilated REMARQUE Placer l appareil dans une pi ce largement ventil e Une quantit d ozone n gligable est d gag e pendant le fonctionnement de l appareil quand celui ci est utilis normalement Cependant une odeur d sagr able peut tre ressentie dans les pi ces dont l a ration est insuffisante et lorsque une utilisation prolong e de l appareil est effectu e Pour avoir la certitude de travailler dans un environnement r unissant des conditions de confort sant et de s curit il est pr f rable de bien a rer la pi ce ou se trouve l appareil Acoustic Noise For European Users Machine Noise Regulation 3 GSGV 18 01 1991 The sound pressure level at the operator position according to EN 27779 is equal to or less than 70dB A 1 12 Di1610 Di1610p 1 4 Energy St
44. TY LEVEL A y LIGHT TOMO DARK am amp YES lt Auto Photo gt LS A FT A 5 22 Di1610 Di1610p 5 5 Specifying Copy Settings 5 Specifying the Setting for DENSITY LEVEL M 1 Select DENSITY LEVEL M o Refer to Selecting the COPY SETTING Menu on page 5 19 2 Press the and keys to select one of the nine print density levels between LIGHT and DENSITY LEVEL M DARK LI GHTOOOOOm00008 DARK A amp YES lt Auto Photo A To _ D Q lt 3 Press the Yes key Using the Utility Mode Di1610 Di1610p 5 23 Chapter 5 Using the Utility Mode 5 5 5 Specifying Copy Settings Specifying the Setting for OUTPUT PRIORITY 1 Select OUTPUT PRIORITY o Refer to Selecting the COPY SETTING Menu on page 5 19 2 Press the and p keys to select either NON or SORT 3 Press the Yes key 5 OUTPUT PRIORITY y NON SORT a amp YES lt a Auto Photo D AA A FT A 5 24 Di1610 Di1610p 5 5 Specifying Copy Settings 5 Specifying the Setting for RESOLUTION 1 Select RESOLUTION o Refer to Selecting the COPY SETTING Menu on page 5 19 2 Press the and p keys to select either
45. a power cord is not supplied only use the power cord and plug that is specified in POWER CORD INSTRUCTION Failure to use this cord could result in a fire or electrical shock e Use the power cord supplied in the package only for this machine and NEVER use it for any other product Failure to observe this precaution could result in a fire or electrical shock e Use only the specified power source voltage Failure to do so could result in a fire or electrical shock Do not use a multiple outlet adapter to connect any other appliances or machines Exceeding a power outlet s current rating could result in a fire or electrical shock Do not unplug or plug in the power cord with a wet hand as an electrical shock could result Plug the power cord all the way into the power outlet Failure to do this could result in a fire or electrical shock Donotscratch abrade place a heavy object on heat twist bend pull on or damage the power cord Use of a damaged power cord exposed core wire broken wire etc could result in a fire or breakdown Should any of these conditions be found immediately turn off the machine unplug the power cord from the power outlet and then call your authorized service representative e Avoid using an extension cord Use of an extension cord could cause a fire or electrical shock Contact your authorized service representative if an extension cord is required Do not place a flower vase or other c
46. ar 14 Energy Star neti As an ENERGY STAR Partner we have determined that this machine meets the ENERGY STAR Guidelines for energy efficiency What is an ENERGY STAR Product An ENERGY STAR product has a special feature that allows it to automatically switch to a low power mode after a period of inactivity An ENERGY STAR product uses energy more efficiently saves you money on utility bills and helps protect the environment Di1610 Di1610p Chapter 1 Introduction Chapter 1 Introduction 1 1 5 Explanation of Manual Conventions 1 5 Explanation of Manual Conventions The marks and text formats used in this manual are described below A WARNING Failure to observe instructions highlighted in this manner may result in fatal or critical injuries Observe all warnings in order to ensure safe use of the copier A CAUTION Failure to observe instructions highlighted in this manner may result in serious injuries or property damage gt Observe all cautions in order to ensure safe use of the copier Note May also appear as Important or Tip Text highlighted in this manner contains useful information and tips to ensure safe use of the copier 1 Thenumber1 as formatted here indicates the first step of a sequence of actions 2 Subsequent numbers as formatted here ae io tens An illustration inserted here shows indicate s
47. bject to direct sunlight and high temperature and humidity as poor image quality and malfunctions could result Do not attempt to replace the toner unit and PC drum unit in a place exposed to direct sunlight If the PC drum is exposed to intense light poor image quality could result e Do not unpack a toner unit or PC drum unit until it is to be used Do not leave a unit unpacked Install it immediately otherwise poor image quality could result Do not keep toner units and PC drum units in an upright position or upside down as poor image quality could result e Do not throw or drop a toner unit or PC drum unit as poor image quality could result Do not use this product in an area where ammonia or other gases or chemicals are present Failure to do so may shorten the service life of the product cause damage to it or decrease its performance Do not use this product in an environment with a temperature outside the range specified in the User Manual as a breakdown or malfunction could result Do not attempt to feed stapled paper carbon paper or aluminum foil through this product as a malfunction or fire could result Do not touch or scratch the surface of the toner unit developing roller and the PC drum as poor image quality could result Use the supplies and consumables recommended by the dealer Use of any supply or consumable not recommended could result in poor image quality and machine breakdown Di1610
48. d Cosmetic Act of 1990 Compliance is mandatory for Laser products marketed in the United States and is reported to the Center for Devices and Radiological Health CDRH of the U S Food and Drug Administration of the U S Department of Health and Human Services DHHS This means that the device does not produce hazardous laser radiation The label shown on page 1 11 indicates compliance with the CDRH regulations and must be attached to laser products marketed in the United States CAUTION Use of controls adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure This is a semiconductor laser The maximum power of the laser diode is 15 mW and the wavelength is 770 800 nm For European Users CAUTION Use of controls adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure This is a semiconductor laser The maximum power of the laser diode is 15 mW and the wavelength is 770 800 nm Di1610 Di1610p 1 9 Chapter 1 Introduction Chapter 1 Introduction 1 1 3 Safety Information For Denmark Users ADVARSEL Usynlig laserstraling ved abning nar sikkerhedsafbrydere er ude af funktion Undg uds ttelse for str ling Klasse 1 laser produkt der opfylder IEC60825 sikkerheds kravene Dansk Dette er en halvlederlaser Laserdiodens h jeste styrke er 15 mW og b lgel ngd
49. e the Auto setting cannot be selected 3 If you want to adjust the image density manually press the or gt key to select the desired setting 4 Make the other necessary settings O O di Tip The displays for manually selected image densities are shown at the right Selecting the Paper on page 4 4 di x1 00 i A A B LTC PHOTO x1 90 i JE p LTE Bei x1 00 t JE b LTE d lt Auto Photo p N TS ET A Light level 4 level 3 level 2 level 1 Standard level 0 level 1 level 3 AAAAAAAAA level 2 Dark level 4 Specifying the Zoom Ratio on page 4 10 5 Using the 10 Key Pad enter the number of copies to be made and then press the Start key Di1610 Di1610p Chapter 4 Making Copies Chapter 4 Making Copies 4 4 5 Making 2in1 Copies 4 5 Making 2in1 Copies Two sheets of single sided documents can be copied onto one double sided sheet Original Copy Sd Note The optional Auto Document Feeder is required Specifying Settings for 2in1 Copies 1 Position the original Note Be sure to position the documents as shown in the illustration at the right 2 Press the 2in1 key and then VW check that the indicator lights
50. en er 770 800 nm For Finland Sweden Users LOUKAN 1 LASERLAITE KLASS 1 LASER APPARAT VAROITUS Laitteen Kayttaminen muulla kuin t ss k ytt ohjeessa mainitulla tavalla saattaa altistaa k ytt j n turvallisuusluokan 1 ylitt v lle n kymatt malle lasers teilylle Tama on puolijohdelaser Laserdiodin sunrin teho on 15 mW ja aallonpituus on 770 800 nm VARNING Om apparaten anv nds p annat s tt n i denna bruksanvisning specificerats kan anv ndaren uts ttas f r osynlig laserstr lning som verskrider gr nsen for laserklass 1 Det h r r en halvledarlaser Den maximala effekten f r laserdioden r 15 mW och v gl ngden r 770 800 nm VARO Avattaessa ja suojalukitus ohitettaessa olet alttiina n kym tt m lle lasers teilylle Al katso s teeseen VARNING Osynlig laserstr lning n r denna del r ppnad och sp rren r urkopplad Betrakta ej str len 1 10 Di1610 Di1610p 1 3 Safety Information 1 For Norway Users ADVERSEL Dersom apparatet brukes pa annen mate enn spesifisert i denne bruksanvisning kan brukeren utsettes for unsynlig laserstraling som overskrider grensen for laser klass 1 Dette en halvleder laser Maksimal effekt till laserdiode er 15 mW og b lgelengde er 770 800 nm Laser Safety Label A laser safety label is attached to the outside of the machine as shown below For United States re MANUFACTURED THIS PRODUCT C
51. ength Y of the paper e 140 356 X OK YES YCr x Not The length can range from 140 mm 5 1 2 to 356 mm 5 14 lt E ERI 2 8 9 J gt O eae Tip 0 Enter the value by mm using ES the 10 key Pad Refer to the e conversion rate below O 1 inch 25 4 mm D Cc S g 10 Press the Yes key Yes 11 Make the other necessary settings o Specifying the Zoom Ratio on page 4 10 o Adjusting the Image Density on page 4 12 12 Using the 10 Key Pad enter the number of copies to be made and then press the Start key lt gt Tip A To change the number of copies to be made remove the paper from the Bypass Tray and then reload it Repeat steps 11 and 12 4 8 Di1610 Di1610p 4 2 Selecting the Paper Sd Note The Bypass Tray can be loaded with a maximum of 1 envelope 1 OHP transparency 1 card or 10 sheets of plain paper Di1610 Di1610p Chapter 4 Making Copies Chapter 4 Making Copies 4 4 3 Specifying the Zoom Ratio 4 3 Specifying the Zoom Ratio By specifying a zoom ratio the copy can be enlarged or reduced Zoom Ratio Settings Zoom Ratio Settings Description Fixed ratios e The following optimum zoom ratios are available for making copies from commonly used original sizes to standard paper sizes x 0 50 x 0 64 LT gt HL x 0 78 LG gt LT x 1 29 HL gt LT x 1 54 HL gt LG e x 2 00
52. ensity TEXT Auto e Zoom ratio 100 full size 0 Before Making Copies Paper Tray1 Finishing Non Sort Tip The default settings can be customized from the Utility mode For details refer to Using the Utility Mode on page 5 1 Di1610 Di1610p 3 11 Chapter 3 Before Making Copies 3 3 6 Useful Functions 3 6 Useful Functions Panel Resetting Press the Panel Reset key to return all modes and functions zoom ratio number of copies etc to their defaults All selected settings are canceled Tip The Panel Reset key comes in handy for canceling all selected settings at one time To avoid accidentally using settings from the previous copy job press the Panel Reset key to return all functions and settings to their defaults before specifying any settings for your current job Auto Panel Reset Even if the Panel Reset key is not pressed the machine automatically resets all functions and settings to their defaults 1 min after a copy cycle has been completed or a key operation is performed Vai Tip The length of time before the machine automatically resets itself can be set between 1 min and 5 min in addition to 30 seconds The Auto Panel Reset function can even be disabled For details refer to Specifying the Setting for AUTO PANEL RESET on page 5 4 Energy Save Mode Instead of turning off the machine it can be set into a standby state Energy Save mode If the machine is not
53. ess the Start key to start the copy cycle 3 26 Di1610 Di1610p 3 8 Loading Originals 3 Positioning Books When copying an open book or magazine position the original as detailed below 1 Raise the Auto Document Feeder or Original Cover 2 Place the original face down on the Original Glass Note Do not place books weighing more than 6 1 2 Ib on the Original Glass In addition do not press down extremely hard on the original otherwise the machine may be damaged m Q lt 3 Position the original on the Original Glass so that the corner of the original aligns with the arrow in the upper left corner of the Original Scales Before Making Copies 4 Gently lower the Auto Document Feeder or Original Cover Note While scanning a thick book or other three dimensional object with the Auto Document Feeder or Original Cover open do not look directly at the bright light that may shine through the Original Glass Although the light that shines through the Original Glass is bright it is not a laser beam and therefore is not as dangerous 5 Specify the desired copy settings O Making Copies on page 4 1 6 Press the Start key to start the copy cycle Di1610 Di1610p 3 27 Chapter 3 Before Making Copies 3 3 9 Checking the Machine Status 3 9 Checking the Machine Status The total number of pages copied and scanned since this machi
54. fault manual density level setting can be set to one of nine levels between 4 and 4 with the normal print density at O If a smaller number toward is selected the print becomes lighter If a larger number toward is selected the print becomes darker e The factory default setting is NORMAL 0 OUTPUT PRIORITY The finishing setting that is selected when the machine is turned on or the Panel Reset key is pressed can be set to NON or SORT e The factory default setting is NON RESOLUTION The default resolution when scanning with the Auto Document Feeder can be set to 600 dpi X 300 dpi or 600 dpi X 600 dpi e The factory default setting is 600 dpi X 300 dpi 5 18 Di1610 Di1610p 5 5 Specifying Copy Settings 5 Selecting the COPY SETTING Menu 1 Press the Utility key four times COPY SETTING appears COPY SETTING 2 i OK YES or 1 6 FT Utility A 2 From the 10 Key Pad press the key 1 to 6 for the COPY SETTING function that you wish to set o The COPY SETTING functions are as follows 1 PAPER PRIORITY 2 DENSITY PRIORITY 3 DENSITY LEVEL A 4 DENSITY LEVEL M 5 OUTPUT PRIORITY 6 RESOLUTION Tip To quit changing the copy settings press the No key STOP SETTING appears Press the Yes key to quit changing the settings lo _ D Q lt Using the Utility Mode
55. fies the type and size of paper to be used with each tray together with its capacity Tray1 Specifications Paper Type e Plain paper recycled paper 16 Ib to 24 lb e Exclusive paper card 24 1 4 Ib to 43 1 4 Ib OHP transparencies envelopes Paper Size e A4L BSL A5 L 16K L Legal L Letter L Invoice L FLS 13 x 8 1 4 e Custom Size Width 3 1 2 to 8 1 2 length 5 1 2 to 14 Capacity e Plain paper recycled paper 250 sheets 20 Ib Exclusive paper card 10 sheets OHP transparencies 5 sheets envelopes 1 sheet Tray2 Specifications Paper Type Plain paper recycled paper 16 Ib to 24 Ib Paper Size Letter L A4 L Capacity 500 sheets 20 Ib Two tray types are availab le for Tray2 Select the desired tray type at the time of purchase Bypass Tray Specifications Paper Type e Plain paper recycled paper 16 Ib to 24 lb e Exclusive paper card 24 1 4 Ib to 43 1 4 Ib OHP transparencies envelopes label sheets Paper Size A4L BSL A5 L 16K L Legal L Letter L Invoice L FLS 13 x 8 1 4 e Custom Size Width 3 1 2 to 8 1 2 length 5 1 2 to 14 Capacity e Plain paper recycled paper 10 sheets 20 lb e Exclusive paper card 1 sheet OHP transparencies 1 sheet envelopes 1 sheet Precautions for Loading Paper e Be sure to observe the paper specifications paper type paper size and capacity for each tray otherwise a paper misfeed could result When paper is l
56. g the Machine Settings 5 Specifying the Setting for DENSITY BOOK 1 Select DENSITY BOOK o Refer to Selecting the MACHINE SETTING Menu on page 5 3 2 Press the and p keys to select either Mode 1 or Mode 2 4 DENSITY BOOK y MODE1 MODE2 am amp YES lt Auto Photo D A To _ D Q lt 3 Press the Yes key Using the Utility Mode Di1610 Di1610p 5 7 Chapter 5 Using the Utility Mode 5 5 2 Specifying the Machine Settings Specifying the Setting for PRINT DENSITY 1 Select PRINT DENSITY o Refer to Selecting the MACHINE SETTING Menu on page 5 3 2 Press the and keys to select one of the seven print density levels between LIGHT 9 PRINT DENSITY and DARK LIGHT JOOOSO0 DARK je 8 YES lt Auto Photo gt D A 3 Press the Yes key 5 8 Di1610 Di1610p 5 2 Specifying the Machine Settings 5 Specifying the Setting for LCD CONTRAST 1 Select LCD CONTRAST o Refer to Selecting the MACHINE SETTING Menu on page 5 3 2 Press the and p keys to select one of the four display contrast levels between LIGHT 6 LCD CONTRAST and DARK LIGHT JOOMSOB DARK a amp YES a Auto Photo D
57. he Display If ORIGINAL DOC JAM remains displayed even after clearing misfed document perform the misfeed clearing procedure again 6 20 Di1610 Di1610p 6 7 When the Message PAPER SIZE ERROR Appears 6 6 7 When the Message PAPER SIZE ERROR Appears If the paper size specified for a paper tray differs from the size of the paper loaded in the tray the message shown below appears when paper is fed from that tray CAUTION PAPER SIZE ERROR Error CAUTION RESET PAPER LTE NA Check the message for the paper tray and the paper size to be fed and then load paper according to the corresponding procedure described below For Tray1 1 Select TRAY1 PAPER o Selecting the PAPER SOURCE SETUP Menu on page 5 12 2 Press the 1 key of the 10 Key Pad and then specify the correct 1 TRAY1 PAPER Co paper type and size o Q O Specifying the Setting for g TRAY1 PAPER on O page 5 13 PLAIN OHP CARD am amp YES y x HLO LTE LG te OK YES CUSTOM When a Message Appears Di1610 Di1610p 6 21 Chapter 6 When a Message Appears 3 Remove the Bypass Tray and 4 Load the desired paper into the 6 7 When the Message PAPER SIZE ERROR Appears then remove all paper from Tray1 tray
58. i161 0p Before using this machine be sure to read the User Manual thoroughly in order to ensure that you use the machine efficiently After you have gone through the manual store it in the holder and keep it handy at all times Note that some of the illustrations of the machine used in the User Manual may be different from what you actually see on your machine For U S A Users FCC Part 15 Radio Frequency Devices NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARNING The design and production of this unit conform to FCC regulations and any changes or modifications must be registered with the FCC and are subject to FCC control Any changes made by the purchaser or user without first contacting the manufacturer will be subject to penalty under FCC regulations This device must be used with shielded interface cables The use of no
59. ime until the machine enters Energy Save mode can be set between 1 min and 240 min in 1 min increments e The factory default setting is 15 min DENSITY ADF The scanning density when using the Auto Document Feeder can be adjusted Mode 1 For printing lighter copies of dark documents to avoid darkening of copies Mode 2 For printing copies with same density as documents e The factory default setting is Mode 1 DENSITY BOOK The density when scanning from the Original Glass can be adjusted Mode 1 For printing copies with same density as documents Mode 2 For printing lighter copies of dark documents to avoid darkening of copies e The factory default setting is Mode 1 PRINT DENSITY The copy print density can be adjusted to one of six levels between 3 and 2 With the normal print density at 0 choose a smaller number for a lighter print or choose a higher number for a darker print e The factory default setting is 0 Normal LCD CONTRAST The brightness of the display can be set to one of four levels between 1 and 2 e The factory default setting is 0 Normal LANGUAGE The display language can be selected e The factory default setting is English 5 2 Di1610 Di1610p 5 2 Specifying the Machine Settings 5 No Name Description 8 LAMP OFF TIME The time until the exposure lamp goes off can be adjusted Mode 1 When four hours
60. imum Legal L Kinds of Paper Plain paper recycled paper 16 Ib to 24 Ib Exclusive paper card 24 1 4 Ib to 43 1 4 lb OHP transparencies envelopes Copy Paper Size lt Tray1 Bypass Tray gt A4L B5 L A5 L 16K L Legal L Letter L Invoice L FLS 13 x 8 1 4 Custom size Width 3 1 2 to 8 1 2 Length 5 1 2 to 14 Capacity lt Tray1 gt Plain paper recycled paper 250 sheets 20 Ib Exclusive paper card 10 sheets OHP transparencies 5 sheets envelopes 1 sheet lt Bypass Tray gt Plain paper recycled paper 10 sheets 20 Ib Exclusive paper card 1 sheet OHP transparencies 1 sheet envelopes 1 sheet Warm up Time Less than 25 seconds at room temperature 73 4 F First Copy Less than 13 seconds Letter L or A4 L First page print time Less than 16 seconds Letter L or A4 L Copy Speed Print 16 sheets min Letter L or A4 L Copy 12 sheets min Letter L or A4 L Zoom Ratios Full size x 1 000 Enlargement ratios x 1 29 x 1 54 and x 2 00 Reduction ratios x 0 50 x 0 64 and x 0 78 Zoom ratios x 0 50 to x 2 00 in x 0 01 increments Multiple Copies 1 to 99 sheets Density Control Auto Text mode Text mode and Photo mode Lost Image Leading edge 1 4 Trailing edge 1 4 Rear edge 1 4 Front edge 1 4 7 2 Di1610 Di1610p 7 1 Specifications Specification Power Requirements 120 127 V less than 7 2 A 60 Hz 220 240 V
61. is prohibited under any circumstances to copy domestic or foreign currencies or works of art without permission of the copyright owner When in doubt about the nature of a document consult with legal counsel 2 6 Di1610 Di1610p Before Making Copies Before Making Copies Chapter 3 Chapter 3 Before Making Copies 3 3 1 Available Features 3 1 Available Features The main copy settings available with this machine are listed below For details on their operation refer to the pages indicated E gt Copies e 1 sided copies p 4 2 e 2in1 copies p 4 14 Zoom Ratio e Reduced Full Size Enlarged p 4 10 Finishing e Sort p 4 15 Cp Cy Gy Ch 3 2 Di1610 Di1610p 3 2 Components and Their Functions 3 3 2 Components and Their Functions Main Unit e Di1610 Di1610p Original Cover Kit OC 7 option for USA and Canada only Presses down on an original placed on the Original Glass era Auto Document Feeder AF 11 option e Automatically feeds originals one page after another for scanning ee Paper Feed Cassette PF 125 option Capable of holding up to 500 sheets of paper LT 32MB Memory M32 5 option e Increases the machine s memory By increasing the machine s memory more pages can be scanned Mechanical Counter 2 option e Displays the total number of pages copied until the current time Network Interface
62. itioning a Sheet Original Use the following procedure to position plain paper or an original that is not suitable for use in the Auto Document Feeder 1 Raise the Auto Document Feeder or Original Cover 2 Place the original face down on the Original Glass 3 Position the original on the Original Glass so that the corner of the original aligns with the arrow in the upper left corner of the Original Scales 4 Gently lower the Auto Document Feeder or Original Cover 5 Specify the desired copy settings O Making Copies on page 4 1 6 Press the Start key to start the copy cycle Di1610 Di1610p 3 25 m Q lt Before Making Copies Chapter 3 Before Making Copies 3 3 8 Loading Originals Positioning Highly Transparent Originals When making a copy from OHP transparencies translucent paper or other highly transparent original position the original as detailed below 1 Raise the Auto Document Feeder or Original Cover 2 Place the original face down on the Original Glass 3 Position the original on the Original Glass so that the corner of the original aligns with the arrow in the upper left corner of the Original Scales 4 Place a blank sheet of paper of the same size over the original 5 Gently lower the Auto Document Feeder or Original Cover 6 Specify the desired copy settings O Making Copies on page 4 1 7 Pr
63. jO 2in1 O ololololojojoj e joje OJO Finishing Non Sort o 00 0 o0 o0 0 0 0 o0 0 0 o Sort O O0OJO0O O O O OJO 6 O OJO Conditions for Combined Functions Code Description O The functions can be combined Oo The functions cannot be combined 7 6 Di1610 Di1610p 7 4 Paper Size and Zoom Ratio Tables 7 4 Paper Size and Zoom Ratio Tables Paper Sizes Paper Format English Size Metric Size Ledger 11x17 279 mm x 432 mm 11x14 11x14 279 mm x 356 mm Computer 10 1 8 x 14 257 mm x 356 mm 10x 14 10x 14 254 mm x 356 mm 9 1 4 x 14 9 1 4 x 14 236 mm x 356 mm Legal 8 1 2 x 14 216 mm x 356 mm Foolscap Government Legal 8 1 2 x 13 216 mm x 330 mm Foolscap 8x13 203 mm x 330 mm Foolscap 8 2 3 x 13 220 mm x 330 mm Foolscap Folio 8 1 4 x 13 210 mm x 330 mm 8 1 4 x 11 3 4 8 1 4 x 11 3 4 210 mm x 301 mm Letter 8 1 2 x 11 216 mm x 279 mm Government Letter 8 x 10 1 2 203 mm x 267 mm Quarto 8x10 203 mm x 254 mm Statement Invoice 5 1 2 x 8 1 2 140 mm x 216 mm 4x6 4x6 102 mm x 152 mm Paper Format Metric Size English Size A3 Wide 311 mm x 457 mm 12 1 4 x 18 A3 297 mm x 420 mm 11 3 4 x 16 1 2 A4 210 mm x 297 mm 8 1 4 x 11 3 4 A5 148 mm x 210 mm 5 3 4 x 8 1 4 A6 105 mm x 148 mm 4 1 4 x 5 3 4 B4 257 mm x 364 mm 10 x 14 1 4 B5 182 mm x 257 mm 7 1 4x 10 B6 128 mm x 182 mm 5 x 7 1 4 Di
64. lecting the Paper on page 4 4 Paper A 3 Specify the zoom ratio O Specifying the Zoom Ratio on v Zoom A page 4 10 ll A 4 2 Di1610 Di1610p 4 1 Making a Basic Copy 4 4 Specify the image density o Adjusting the Image Density a Auto Photo D on page 4 12 A 5 Using the 10 Key Pad enter the number of copies to be made Any number from 1 to 99 can be o 9 OX 0 _ 6 Press the Start key This will start the copy cycle O To stop the copy cycle in mid d operation press the Stop key O O To cancel the copy job press the No key or the Panel Reset key O To restart the copy cycle press the Start key Di1610 Di1610p 4 3 Chapter 4 Making Copies Chapter 4 Making Copies 4 4 2 Selecting the Paper 4 2 Selecting the Paper Before making a copy the tray containing the paper to be used must be selected Either a paper tray can be selected or paper can be loaded into the Bypass Tray Manual Paper Selection The tray containing the paper you want to use can be manually selected Note The optional Paper Feed Cassette is required Selecting Manually Fed Paper When the desired paper is loaded into the Bypass Tray and the paper size and type are specified paper loaded into the Bypass Tray is given priority during feeding Manually Selecting the Paper Size 1 Position the original O Loading Originals on page
65. less than 3 8 A 50 60 Hz Power Consumption 120 127 V less than 840 W 220 240 V less than 850 W Dimensions 20 width x 24 depth x 16 height Standard Memory 16 MB Weight 32 3 4 Ib Auto Document Feeder AF 11 Specification Document Feeding System Standard Mode 1 sided original Kinds of Original Plain paper 9 1 4 Ib to 34 Ib Original Size AA L B5 L A5 L Legal L Letter L Invoice L Custom size Width 5 1 2 to 8 1 2 Length 5 1 2 to 14 Capacity of Document Feed Tray Maximum 50 sheets 20 Ib Power Consumption 30 W Dimensions 19 1 2 width x 14 depth x 3 1 4 height Weight 7 lb Paper Feed Cassette PF 125 Specification Kinds or Paper Plain paper recycled paper 16 Ib to 24 Ib Paper Sizes Letter L A4 L Capacity 500 sheets 20 Ib Power Consumption Less than 7 W Dimensions 15 3 4 width x 24 1 4 depth x 5 1 2 height Weight 9 1 2 Ib Di1610 Di1610p 7 3 N fod Q o Ve Miscellaneous Chapter 7 Miscellaneous 7 7 2 Care of the Machine 7 2 Care of the Machine Cleaning Turn off the machine before cleaning it Housing Cover gt Wipe the surface of the housing cover with a soft cloth dampened with a mild household detergent Original Glass gt Wipe the surface of the Original Glass clean with a soft dry cloth Di
66. liquids or gases near this product as a fire could result Do not leave toner units or drum units within easy reach of children Licking or ingesting any of these items could be harmful to your health Do not let any object plug the ventilation holes of this product Heat could accumulate inside the product resulting in a fire or malfunction Do not install this product at a site that is exposed to direct sunlight or near an air conditioner or heating apparatus The resultant temperature changes inside the product could cause a malfunction fire or electrical shock Do not place the product in a dusty place or a site exposed to soot or steam near a kitchen table bath or a humidifier A fire electrical shock or breakdown could result Do not place this product on an unstable or tilted bench or in a location exposed to excessive vibration and shock It could drop or fall causing personal injury or mechanical breakdown e After installing this product mount it on a secure base If the unit moves or falls it may cause personal injury e Do not store toner units and PC drum units near a floppy disk or watch that are susceptible to magnetism They could cause these products to malfunction The inside of this product has areas subject to high temperature which may cause burns When checking the inside of the unit for malfunctions such as a paper misfeed do not touch the areas around the fusing unit etc that are indica
67. loth The Drum Cartridge has reached the end of its service life Contact your service representative The image on the copy is not aligned properly i The original is not placed in the correct position Place the original correctly on the Original Glass against the Original Scales Or load it in the Auto Document Feeder correctly along the Document Guide Plates The original may not be suitable for use in the Auto Document Feeder Raise the Auto Document Feeder and place the original on the Original Glass correctly against the Original Scales The paper guides are not pressed up against the paper stack in the tray Slide the paper guides against the edges of the paper stack The paper has an excessive curl Smooth out curls in the paper and reload the paper stack in the tray The printed page is curled The paper that was used curls easily as with recycled paper Remove the paper from the paper tray turn it over and then load it again Change the paper Di1610 Di1610p 6 27 Ce _ O o lt When a Message Appears Chapter 6 When a Message Appears 6 6 10 When Incorrect Copies Are Produced Symptom Possible Cause Action The edge of the copy is dirty The Original Pad is dirty Wipe the Original Pad clean with a soft cloth dampened with neutral detergent You have selected paper of a
68. ls of the specified type Precautions for Loading Paper Into the Auto Document Feeder The following types of originals are not suitable for use in the Auto Document Feeder as a misfeed or damaged original could result Place such types of originals on the Original Glass Typing paper paraffin paper and other thin paper Cards Originals larger than Legal L or smaller than Invoice OHP transparencies translucent paper Wrinkled dog eared curled or torn originals Clipped or stapled originals Coated originals such as carbon backed paper Up to 25 Letter size document pages can be scanned and stored in the memory at one time However if the optional expansion memory is installed up to 180 scanned pages can be stored 3 22 Di1610 Di1610p 3 8 Loading Originals 3 Loading Originals into the Auto Document Feeder 1 Place the stack of originals face up on the Document Feeder Tray Note A maximum of 50 document pages can be loaded Do not load so many pages that the top of the stack is higher than the W mark m Q lt Be sure to adjust the document guides so that they are against the edges of the document otherwise the document may not be fed in straight 2 Slide the front adjustable Document Guide Plate to the size of the originals Before Making Copies 3 Specify the desired copy settings O Making Copies on page 4 1 4 Press the Start
69. mpty the message shown below appears and making copies or printing can no longer be performed Replace the toner cartridge lt Toner empty gt CAUTION TONER EMPTY N 7 Error CAUTION CHANGE TONER Ce _ O o lt A CAUTION Used Toner Cartridges 3 Inorderto prevent the used Toner Cartridge from dirtying anything keep it in the box Dispose of the used Toner Cartridge according to your local regulations When a Message Appears A Note Use only the toner that has been manufactured specifically for this machine Never use any other types of toner as a malfunction could result For details contact your service representative Di1610 Di1610p 6 5 Chapter 6 When a Message Appears 6 2 When the Message TONER EMPTY Appears Before replacing the toner cartridge check that it is of the following type For USA and Canada Toner Cartridge 101 C For countries other than the USA and Canada Toner Cartridge 101 B Do not use a toner cartridge of a different type Replacing the Toner Cartridge 1 2 3 Open the Front Cover Grab the handle of the Imaging Cartridge and then pull it toward you to remove the cartridge x Note Since the Imaging Cartridge can easily be damaged by light exposing the cartridge to light for a long period of time will result in decreased image quality
70. n shielded cable is likely to result in interference with radio communications and is prohibited under FCC rules 1 2 Di1610 Di1610p 1 1 We Want You to Be a Satisfied Customer 1 For Canada Users Interference Causing Equipment Standard ICES 003 Issue 3 This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme a la norme NMB 003 du Canada For users in countries subject to Class B regulations This device must be used with shielded interface cables The use of non shielded cable is likely to result in interference with radio communications and is prohibited under CISPR 22 rules and local rules For users in countries not subject to Class B regulations WARNING This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures This device must be used with shielded interface cables The use of non shielded cable is likely to result in interference with radio communications and is prohibited under CISPR 22 rules and local rules Di1610 Di1610p 1 3 Chapter 1 Introduction Chapter 1 Introduction 1 1 2 SAFETY INFORMATION 1 2 SAFETY INFORMATION This section contains detailed instructions on the operation and maintenance of this machine To achieve optimum use of this device all operators should carefully read and follow the instructions in this manual Please
71. ne i 3 10 To turn off the Machine i 3 10 When the Machine is Turned ON i 3 10 Default Settings voii ile dii dei 3 11 3 6 Useful FUNCtIONS rrrrrrriere rie eri 3 12 Panel Resetting 22sec San ILA A ee 3 12 Auto Panel Reset ian anali 3 12 Energy Save Mode i 3 12 AU Copy Ma ssaa he AGG ereaic 3 13 Auto Tray Switching ii 3 13 37 Copv Pap er inniaruniiisiianiziii ein 3 14 Paper Specifications isisi eiii 3 14 Precautions for Loading Paper i 3 14 Unsuitable Paper ii 3 15 Loading Papers paia iii lla 3 16 Loading Paper into Tray1 ii 3 18 ii Di1610 Di1610p Contents Loading Paper into the Bypass Tray 3 20 Loading Paper into Tray2 Optional n 3 21 3 8 Loading Origitnalls csecssseseseeeeeeeseeeseeeeeeeseseeeeeeeeeeesneeensaeenees 3 22 Two Ways of Loading the Original eceseeeeeeeeeeeeeeenees 3 22 Specific Types of Originals ccceecceeseeeseeeseeeeeeeeeeeeeeeeneetaes 3 22 Loading Originals in the Auto Document Feeder 3 22 Precautions for Loading Paper Into the Auto Document ol nati cda 3 22 Loading Originals into the Auto Document Feeder 3 23 Placing the Original on the Original Glass 3 24 Precautions for Placing the Original on the Original Glass 3 2
72. ne was installed can be checked Checking the Machine Status Menu Item Description TOTAL PAGE TOTAL COUNT Displays the total number of pages copied since this machine was installed TOTAL SCAN Displays the total number of pages scanned since this machine was installed However the scanned number of pages in copy are not included PRINT REPORT CONFIGRATION PAGE Prints the current machine configuration PCL FONT LIST Prints the font list PRINT REPORT appears only for the Di1610p Checking the TOTAL PAGE Counts 1 Press the Status key Stat atus aP 2 Press the Yes key TOTAL PAGE OK YES Yes Ene 3 28 Di1610 Di1610p 3 9 Checking the Machine Status 3 3 Press the V and A keys to check the TOTAL COUNT or TOTAL COUNT 000000 dh TOTAL SCAN values CHECK FINISH YES 7 t TOTAL SCAN 000808 CHECK FINISH YES v Zoom A A a F m Q lt Before Making Copies Di1610 Di1610p 3 29 Chapter 3 Before Making Copies 3 3 9 Checking the Machine Status To output a report list 1 Press the Status key 2 times 2 Press the Yes key 3 Press the V and A keys to select the report list that you wish to print and then press the Yes key After the specified report list is printed the main screen appears again Status
73. ntrast Refer to Specifying the Setting for LCD CONTRAST on page 5 9 The Start key indicator does not light up green The machine has just been turned on and is warming up It takes the machine less t han 25 seconds to be ready to make copies after it has been turned on Please wait The machine does not operate when it is turned on The power cord is left unplugged Plug the power cord into the power outlet The room s circuit breaker is open Close the room s circuit breaker If the problem is not corrected even after the operations described are performed turn off the machine unplug its power cord and then contact the service representative Di1610 Di1610p 6 29 Ce _ O o lt When a Message Appears Chapter 6 When a Message Appears 6 11 The machine is not functioning as designed 6 30 Di1610 Di1610p Miscellaneous Miscellaneous Chapter 7 Chapter 7 Miscellaneous 7 7 1 Specifications 7 1 Specifications Di1610 Di1610p Specification Type Desktop Platen Type Fixed platen unit scanning Photoconductor OPC Copying System Electrostatic Dry Powdered Image Transfer to Plain Paper Developing System Single component developing system Fusing System Lamp Heated Roller Resolution 600 dpi x 600 dpi Types of Original Types Sheets books Size Max
74. oaded into the Bypass Tray a message appears indicating that the paper size be specified Specify the size and type of paper that is loaded Paper loaded into the Bypass Tray is given priority during feeding The size of FLS is preset to 13 x 8 1 4 To change the FLS size contact a service representative 3 14 Di1610 Di1610p 3 7 Copy Paper 3 Unsuitable Paper The following types of paper should not be used otherwise decreased print quality paper misfeeds or damage to the machine may occur Overhead projector transparencies that have already been fed through the machine Even if the transparency is still blank do not reuse it e Paper that has been printed on by a heat transfer printer or an inkjet printer e Paper that is either extremely thick or extremely thin e Folded curled wrinkled or torn paper e Paper that has been left unwrapped for a long period of time 2 e Damp paper g e Perforated paper or paper with punched holes S e Extremely smooth or extremely rough paper or paper with an uneven surface e Paper that has been treated such as carbon backed heat sensitive or pressure sensitive paper S e Paper that has been decorated with foil or embossing e Paper of a non standard shape not rectangular e Paper that is bound with glue staples or paper clips e Paper with labels attached S e Paper with ribbons hooks buttons etc attached 2 e Curled or wrinkled paper e Art paper coa
75. ontainer that contains water or metal clips or other small metallic objects on this product Spilled water or metallic objects dropped inside the product could result in a fire electrical shock or breakdown Should a piece of metal water or any other similar foreign matter fall inside the product immediately turn off the machine unplug the power cord from the power outlet and then call your authorized service representative Do not continue using this product if it becomes unusually hot or if it emits smoke unusual odors or noise Immediately turn off the machine unplug the power cord from the power outlet and then call your authorized service representative If you continue using it in this condition a fire or electrical shock could result Do not continue using this product if it has been dropped or its cover is damaged Immediately turn off the machine unplug the power cord from the power outlet and then call your authorized service representative If you continue using it in this condition a fire or electrical shock could result Do not throw the toner cartridge or toner into an open flame The hot toner may scatter and cause burns or other damage GO AO OSE Connect the power cord to an electrical outlet that is equipped with a grounding terminal Di1610 Di1610p 1 5 Chapter 1 Introduction Chapter 1 Introduction 1 1 2 SAFETY INFORMATION CAUTION Do not use flammable sprays
76. ontal or landscape orientation indicated by either C or Di1610 Di1610p Precaution Precaution Chapter 2 Chapter 2 Precaution 2 2 1 Installation Precautions Observe the following precautions to maintain the machine in its best possible condition 2 1 Installation Precautions Installation Site To ensure utmost safety and prevent possible malfunctions install the machine in a location that meets the following requirements A location away from curtains etc that may catch fire and burn easily A location that is not exposed to water or other liquids A location free from direct sunlight A location out of the direct airflow of an air conditioner or heater and not exposed to extremely high or low temperatures A well ventilated location A location that is not exposed to high humidity A location that is not extremely dusty A location not subjected to undue vibrations A stable and level location A location where ammonia or other organic gases are not generated A location that does not put the operator in the direct airflow of exhaust from the machine A location that is not near any kind of heating devices Power Source The power source requirements are as follows e Voltage Fluctuation AC110 V 10 AC127 V 6 or AC220 240 V 10 e Frequency Fluctuation Within 3Hz O Use a power source with as few voltage or frequency fluctuations as possible
77. r that has been removed from its wrapper but not loaded in the machine should be stored in a sealed plastic bag in a cool dark place Use only toner that has been manufactured specifically for this machine Never use other types of toner Keep all supplies out of the reach of children A CAUTION Be careful not to spill toner inside the machine or get toner on your clothes or hands 3 f your hands become soiled with toner immediately wash them with soap and water Di1610 Di1610p 2 5 Chapter 2 Precaution Chapter 2 Precaution 2 2 3 Legal Restrictions on Copying 2 3 Legal Restrictions on Copying Certain types of documents must not be copied with the purpose or intent to pass copies of such documents off as the originals The following is not a complete list but is meant to be used as a guide to responsible copying lt Financial Instruments gt Personal checks Travelers checks Money orders Certificates of deposit Bonds or other certificates of indebtedness Stock certificates lt Legal Documents gt Food stamps Postage stamps canceled or uncanceled Checks or drafts drawn by government agencies Internal revenue stamps canceled or uncanceled Passports Immigration papers Motor vehicle licenses and titles House and property titles and deeds lt General gt e Identification cards badges or insignias e Copyrighted works without permission of the copyright owner In addition it
78. r the printer controller 3 Error lamp The indicator lights up in orange if an error or malfunction occurs For details refer to When a Message Appears on page 6 1 4 Display Shows the number of copies to be made the zoom ratio and other setting date 5 No C key e Press to reset the number of copies to 1 e Press to clear the various settings e Press to return to the previous screen e Press to specify the various settings 6 Yes key e Press to validate the setting just made e Press to specify the various settings 1 10 Key Pad Use to type in the number of copies to be made and any other numeric date 8 Stop key e Press to stop a print cycle e Press to stop a scanning sequence e The indicator flashes in orange when the machine is paused or while copying 9 Panel Reset key Press to reset all copy functions and settings to their defaults 3 8 Di1610 Di1610p 3 4 Control Panel No Part Name Description 10 Start key Press to start a scanning or print cycle e Press to specify the various settings The indicator lights up in green when the machine can accept copy jobs 11 A V key e Press to change the zoom ratio in the range between x 0 50 and x 2 00 in x 0 01 increments e Press to scan through the various settings and information in order Pressto specify the various settings 12 Zoom key Press to select a zoom ratio from among those fixed ratios available as standard 1
79. replacing the drum cartridge refer to Replacing the Drum Cartridge on page 6 10 To select the USER MANAGEMENT menu 1 Press the Utility key three times USER MANAGEMENT appears USER MANEGEMENT OK YES 7 lo _ D Q lt 2 Pressthe Yes key 3 Press the Yes key CHANGE D C OK YES Using the Utility Mode Di1610 Di1610p 5 17 Chapter 5 Using the Utility Mode 5 5 5 Specifying Copy Settings 5 5 Specifying Copy Settings When the machine is turned on or the Panel Reset key is pressed the machine is automatically reset to its initial mode By changing the default settings you can change the initial mode Refer to the following table for the default settings for each function No Name Description PAPER PRIORITY The tray that is given priority can be set to either Tray1 or Tray2 e The factory default setting is TRAY1 DENSITY PRIORITY The density that is selected when the machine is turned on or the Panel Reset key is pressed can be set to AUTO MANUAL or PHOTO e The factory default setting is AUTO DENSITY LEVEL A A Auto The default Auto density level setting can be set to LIGHT 1 NORMAL 0 or DARK 1 e The factory default setting is NORMAL 0 DENSITY LEVEL M M Manual The de
80. ridge from the Drum Cartridge do not tilt the cartridge otherwise toner may spill When a Message Appears Do not touch the PC drum under the flap of the Drum Cartridge otherwise decreased image quality may result Di1610 Di1610p 6 11 Chapter 6 When a Message Appears 6 6 3 When the Message D C LIFE Appears Do not touch any metal parts of the Drum Cartridge or Toner Cartridge otherwise the units may be damaged by static electricity 5 Align the blue parts of the new Drum Cartridge and the Toner Cartridge and then attach them together 6 Align the tab on the Imaging Cartridge with the rail in the machine and then install the cartridge x Note Do not push in the Imaging Cartridge with excessive force if the cartridge is not correctly aligned on the rail otherwise the units may be damaged 7 Close the Front Cover Note After replacing the Drum Cartridge specify the necessary setting for the function on the USER MANAGEMENT menu in the Utility mode 6 12 Di1610 Di1610p 6 4 When the Message PAPER MISFEED Appears 6 6 4 When the Message PAPER MISFEED Appears If the message shown below appears during printing and the machine stops operating a paper misfeed has occurred in a paper tray Follow the procedure described below to clear the misfed paper xx y Error CAUTION PAPER MISFEED t
81. rix i 7 6 image density i caselle ei ib BR 4 12 8 2 Di1610 Di1610p 8 1 Index Installation Site ia iaia adil ibaa tie LA tek 2 2 Legal restrictions ON COPYING i 2 6 Loading original Auto Document Feeder 3 22 3 23 Precautions i ipa 3 22 Specific types of originals i 3 22 L oading papert sciacalli i 3 16 Bypass itray iii aLaaa Made Rei 3 20 6 3 Precautions ici fair ea 3 14 Travi cio ppi ore brain elise aliene ioni 3 18 6 3 Trav2 ae bullo Ai aiar Aa 3 21 6 4 Machine settirigsi sea Alani nie nd Ag Anlinnd inde 5 2 Machine Status cascade dipolo a 3 28 Messages D C ite aa aa 6 10 Machinertroubles titanio Aerts i ae 6 24 Original document jam eeeeeeteeeeeteeeeeeeeteaeeteaeteaeeteeeeaeeeeetias 6 19 Paper emply s asce lhi aiar iaia 6 2 Paperjam aine he ba teen iat landi 6 16 Papermisfeed ciil iaia ni Aaa 6 13 Paper size Ermita he fiala Aol biella 6 21 Toner an e ciar ii RR AA 6 5 Operating environment sseseesseeseeeieeseeeeneenttteennstntttntenntuntensenstnttnnsenne 2 4 Paper Paper specifications i 3 14 Unsuitable Paper comicidad 3 15 Paper feed cassette PF 125 iii 7 3 Paperteeding ni usare aa 1 15 Paperlerigth ti alal lapo LI sli EUR 1 16 Paper orientationi scsi diari 1 16 Paper Select la 4 4 Di1610 Di1610p 8 3 Chapter 8 Index Chapter 8 Index 8 1 Index Paper sizes
82. s a Di1610 Di1610p 4 5 Chapter 4 Making Copies Chapter 4 Making Copies 4 4 2 Selecting the Paper 6 Press the and keys or press the W key to select the size of paper that is loaded If CUSTOM is not selected continue with step 10 o If CUSTOM is selected perform steps 7 through 10 A Note If OHP was selected in step 4 the only paper sizes that can be loaded are A4 and Letter Tip Pressing the and keys moves E to select the paper size To return to the previous message press the No key a HLD OK YES LTD LGE e CUSTOM lt Auto Photo D Di1610 Di1610p 4 2 Selecting the Paper 7 Using the 10 Key Pad enter the width X of the paper X 200 90 216 x o To clear the entered value OK YES y Crt press the C key a Note The width can range from 90 mm 3 1 2 to 216 mm A 8 1 2 OO When entering the paper size refer to the diagram on the 0 right side of the screen to check which sides of the paper are the width and the length Tray 1 di Tip Enter the value by mm using the 10 Key Pad Refer to the conversion rate below 1 inch 25 4 mm Chapter 4 Making Copies Di1610 Di1610p 4 7 4 4 2 Selecting the Paper 8 Press the Yes key Yes A 9 Using the 10 Key Pad enter the l
83. size larger than the original when the zoom ratio is full size Select paper that is the same size as the document Otherwise enlarge the copy to the selected paper size The original is not placed in the correct position when the zoom ratio is full size Select the same paper size as the original Or reload the paper in the same direction as the original The reduction ratio selected does not match the paper size when the copy is made at a manually adjusted reduction ratio Select a zoom ratio that adjusts the copy size to the size of the selected paper Otherwise make a reduced copy with a zoom ratio that matches the paper size service representative If the problem is not corrected even after the operations described above are performed contact your 6 28 Di1610 Di1610p 6 11 The machine is not functioning as designed 6 11 The machine is not functioning as designed Symptom Possible Cause Action Nothing appears in the Display Is only the Start key lit green The Energy Save mode is enabled Press any key on the Control Panel to cancel Energy Save mode Has the machine been turned on Check that the power cord is firmly connected and that the on side of the Power Switch has been pressed Is the contrast of the Display too light From the MACHINE SETTING menu of the Utility mode adjust the Display to the correct co
84. ted by a CAUTION HOT caution label Do not place any objects around the power plug as the power plug may be difficult to pull out when an emergency occurs The power outlet should be installed near the machine and should be easily accessible so that the power plug can easily be pulled out if an emergency occurs e Always use this product in a well ventilated location Operating the product in a poorly ventilated room for an extended period of time could be harmful to your health Ventilate the room at regular intervals e When moving this product be sure to disconnect the power cord and other cables Failure to do this could damage the cord or cable resulting in a fire electrical shock or breakdown e When moving this product always hold it at the areas indicated in the User Manual and other documents If the unit falls it may cause severe personal injuries or the product may be damaged or malfunction Remove the power plug from the outlet more than once a year and clean the area between the plug terminals Dust that accumulates between the plug terminals may cause a fire When unplugging the power cord be sure to hold onto the plug Pulling on the power cord could damage the cord resulting in a fire or electrical shock SSO0P 1 6 Di1610 Di1610p 1 2 SAFETY INFORMATION 1 Precautions for Routine Use Do not store toner units PC drum units and other supplies and consumables in a place su
85. ted paper or inkjet printer paper Di1610 Di1610p 3 15 Chapter 3 Before Making Copies 3 3 7 Copy Paper Loading Paper While loading paper be sure to observe the following precautions e Ifthe paper is curled flatten it before loading it Do not load so much paper that the top of the stack is higher than the w mark or exceeds the specified number of sheets e Push the paper guides firmly up against the edges of the paper When loading additional paper remove any paper remaining in the drawer place it on top of the new paper and then align the paper in the stack well before loading it into the drawer Di1610 Di1610p 3 7 Copy Paper 3 When loading envelopes load them with the flap facing down as shown in the illustration at the right Note Before loading envelopes press them down to make sure that all air is removed and make sure that the folds of the flaps are firmly pressed otherwise the envelopes may become wrinkled or a paper misfeed may occur lt Bypass Tray gt Chapter 3 Only 1 envelope at a time can be loaded in Tray1 and the Bypass Tray Before Making Copies Tip We recommend replenishing the paper only after all of the paper in the drawer has been used Di1610 Di1610p 3 17 Chapter 3 Before Making Copies 3 3 7 Copy Paper Loading Paper into Tray1 1 Remove the Bypass Tray
86. the machine always be sure that the current copy cycle has been completed Tuming off the machine will initialize all settings except those for previously programmed jobs and for the Utility mode The machine automatically enters the Energy Save mode 15 min after the last operation is performed The time until the machine enters Energy Save mode can be specified from the Utility mode For details refer to Specifying the Setting for ENERGY SAVE MODE on page 5 5 in the chapter Using the Utility Mode When the Machine is Turned On When the machine is turned on the Start key indicator lights up in orange to indicate that the machine is ready to begin copying At this time the machine can be set for the Auto Copy Start function by loading a document into the Auto Document Feeder or by placing a document on the Original Glass and pressing the Start key Pressing the Start key at this time will not immediately start the copy cycle You will have to wait for less than 25 seconds at an ambient temperature of 73 4 F 3 10 Di1610 Di1610p 3 5 Turning the Machine On Off and the Initial Mode 3 Default Settings When the machine is turned on the Initial mode screen appears in the Display of the Control Panel The Initial mode screen appears at the beginning of all operations TEXT x1 09 JIA B LTE m _ a Q lt Factory default settings e Number of copies 1 Image d
87. ti iii ARR ari 7 7 Paper source settings ui 5 12 Paper Width isc aaa iras ds 1 16 Placing original Original glaSS trar i 3 24 PTECAUIONS ccrta a ri 3 24 Specific types of originals i 3 22 Positioning BOOKS siii aio Heh i alii bia illo dico slice li 3 27 Highly transparent Originals ii 3 26 Sheet Original i paredes 3 25 Power SOUC Seiki tore ei alal 2 2 Printarea siorni rai dist eerie tarda eS 3 31 Replacing Tonercartridge iure tela a alia 6 6 Resetting Auto panel reset isernia ilaria alal 3 12 Panel caca 3 12 SONING sita A til 4 16 Space requirements ii 2 3 Specifications cateteri cates allinea 7 2 Turning Ofelia ile tevin a i ela 3 10 a aa ariani 3 10 User management settings ie 5 17 Utilityimode israeliana ii 5 2 ZOOM ratio ii cia ei lidi Alari 4 10 7 8 Di1610 Di1610p KONICA MINOLTA Copyright 2003 KONICA MINOLTA BUSINESS TECHNOLOGIES INC The information contained in this manual is subject to change without notice to incorporate improvements made on the product or products the manual covers KONICA MINOLTA BUSINESS TECHNOLOGIES INC 2004 8 Marunouchi Center Building 1 6 1 Marunouchi Chiyoda ku Tokyo 100 0005 Japan 4980 7783 02 P N 91164C057H023
88. ubsequent steps of a sequence of what operations must be performed actions Text formatted in this style provides additional assistance gt Text formatted in this style describes the action that will ensure the desired results are achieved Copy key The names of keys on the control panel are written as shown above 1 14 Di1610 Di1610p 1 6 Explanation of Basic Concepts and Symbols 1 1 6 Explanation of Basic Concepts and Symbols The use of words and symbols in this manual are explained below Paper Feeding During printing paper is supplied from the right side of the copier and fed into the Copy Tray on top with the printed surface of the page facing down The paper feed direction is shown by the arrows in the diagram below Di1610 Di1610p 1 15 Chapter 1 Introduction Chapter 1 Introduction 1 1 6 Explanation of Basic Concepts and Symbols Width and Length Whenever paper dimensions are mentioned in this manual the first value always refers to the width of the paper shown as A in the illustration and the second to the length shown as B A Width B Length Paper Orientation Lengthwise L7 If the width A of the paper is shorter than the length B the paper has a vertical or portrait orientation indicated by either L or Ly Crosswise F If the width A of the paper is longer than the length B the paper has a horiz
89. used for a set length of time it will automatically enter the Energy Save mode The default length of time is 15 min To cancel the Energy Save mode press any key on the control panel Tip The length of time before the machine enters the Energy Save mode can be set between 1 min and 240 min For details refer to Specifying the Setting for ENERGY SAVE MODE on page 5 5 3 12 Di1610 Di1610p 3 6 Useful Functions 3 Auto Copy Start If a document is loaded and the Start key is pressed during the period after the machine has been turned on but before it is ready to make copies the machine will automatically start the copy cycle as soon as it completes the warm up cycle Auto Tray Switching If the tray runs out of paper while printing the machine will automatically switch to a different paper source and continue copying provided that the new tray contains paper of the same type and size in the same orientation If the optional Paper Feed Cassette is installed a maximum of 750 copies can be continuously printed m _ D o lt Tray1 gt Tray2 Paper Feed Cassette Tray2 Paper Feed Cassette Tray1 Tip Auto tray switching can be disabled For details refer to Setting Up the Paper Sources on page 5 12 Before Making Copies Di1610 Di1610p 3 13 Chapter 3 Before Making Copies 3 3 Paper Specifications 3 7 Copy Paper 7 Copy Paper The following table speci
90. ypass Tray FRONT COVER OPEN t CLOSE FRONT COVER The Front Cover of the main unit is open or not securely closed Securely close the Front Cover DOCUMENT COVER OPEN t CLOSE DOCUMENT COVER The Auto Document Feeder is lifted up while a document is loaded into it Securely close the Auto Document Feeder or remove the document from the Auto Document Feeder DOC FEED COVER OPEN t CLOSE DOC FEED COVER The Document Feeder Cover is open Securely close the Document Feeder Cover MEMORY FULL t PRESS ANY KEY The size of the data for the scanned document has exceeded the capacity of the memory Press the Panel Reset key or turn the machine off then on again The scanned data should be cleared from the memory MACHINE TROUBLE t SERVICE CALL C Some problem occurred in the machine Turn the machine off then on again If the error is still displayed contact your service representative FUSER COVER OPEN t CLOSE FUSER COVER The Fuser Cover of the main unit is open or not securely closed Securely close the Fuser Cover PAPER JAM t OPEN FRONT COVER A paper misfeed occurred All misfed paper was not removed from the main unit Perform the misfeed clearing procedure p 6 16 The Fuser Cover of the main unit is open or not securely closed Close the Fuser Cover then open and close the Front Cover INCORR
91. ys make sure that the power plug is completely plugged into the electrical output Always make sure that the machine s power plug is visible and not hidden by the machine a Always unplug the machine from the electrical outlet if the machine is not to be used for a long period of time Always provide good ventilation when making a large number of continuous copies printed pages A CAUTION A negligible amount of ozone is generated during normal operation of this machine An unpleasant odor may however be detected in poorly ventilated rooms during extensive machine operations gt Fora comfortable operating environment it is recommended that the room be well ventilated 2 4 Di1610 Di1610p 2 2 Operation Precautions 2 A CAUTION The area around the Fusing Unit is extremely hot In order to reduce the risk of burns do not touch any area other than those indicated in the manual Be especially careful not to touch parts marked with warning labels and their surrounding areas Transporting the Machine If you need to transport the machine over a long distance consult your service representative Care of Machine Supplies Use the following precautions when handling the machine supplies toner paper etc F Store the supplies in a location that meets the following requirements Free from direct sunlight Away from any heating apparatus Not subjected to high humidity Not extremely dusty Pape

User Manual - Pdfstream.manualsonline.com

Contents

Download Pdf Manuals

Related Search

Related Contents