Network Camera - General Security
Contents
1. 5 Adjust surveillance angel 1 Loosen the knob to adjust the panning position and tilting position 2 After adjusting the angle of the camera to the desired position fasten the knob 13 Network Camera Quick Operation Guide Figure 3 6 Adjust the Camera 14 Network Camera Quick Operation Guide 4 Setting the Network Camera over the LAN Purpose To view and configure the camera via LAN Local Area Network you need to connect the network camera in the same subnet with your PC Then install the SADP or iVMS 4200 software to search and change the IP of network camera p ime r NOTE The SADP and iVMS 4200 software are on the disk in the camera packet Connection of network camera and PC ie _ Network Cable rr Network Cables Figure 4 1 Wiring over LAN Set the IP address of the camera for accessing via LAN Steps 15 Network Camera Quick Operation Guide 1 To get the IP address you can choose either of the following methods Use SADP a software tool which can automatically detect network camera in the LAN and list the device information like IP address subnet mask port number device serial number device version etc shown in Figure 4 2 Use iVMS 4200 software and to list the online devices Please refer to the user manual of client software for detailed information Change the IP address and subnet mask to the same subnet as of your PC Refer2. Fi settings Press the WPS button on the camera and press the Network Camera Quick Operation Guide WPS button on the wireless router the camera can be easily connected on line Network Camera Quick Operation Guide 2 Notice Do not install the camera Do nottouch the lens with in the extreme whether your figure condition Do not install the camera Do not subject the towards the strong light camera to vibration or in the unstable shock or heavy pressure lightening condition Network Camera Quick Operation Guide High humidity may Under no circumstances damage the camera should you submerge the hardware put it in dry camera in any type of and well ventilated place liquid RS NN Electromagnetic radiation may affect the video data transmission and the image quality Do not install the camera near Network Camera Quick Operation Guide 3 Installation Pim Nore Read the following contents carefully before the installation Make sure that all the related equipment is power off during the installation Check whether the power supply is matched with your AC outlet to avoid damage If the product does not function properly please contact your dealer or the nearest service center Do not disassemble the camera for repair or maintenance by yourself Make sure the installation location does not have reflective surfaces of objects close to the camera The IR light
3. to the following introductions to set IP address with SADP software Search active devices online Search online devices automatically After running the SADP software it automatically searches the online devices every 15 seconds from the subnet where your computer locates It displays the total number and information of the searched devices in the Online Devices interface Device information including the device type IP address port number gateway etc will be displayed 16 Network Camera Quick Operation Guide Retesh Total wader of saline devices O Rete Modh Netw Deia Typa Wd agaes Pot Software vernon Pv Galway Soria No Adaess OS XXXM Nx 1920 90 64 8206 VK Xe 1920 01 Por Subnet Mast vs Cateeny PO Adoess IPO Gateway PO Pretclengn Seny No o Note Erfe he acrren password of the devos Deore yos Save Me network parameters Note Sertai code is 3 seios of characters Q Combined iy De statine mad Me senal number of he dewce Figure 4 2 Searching Online Devices NOTE Device can be searched and displayed in the list in 15 seconds after it goes online it will be removed from the list in 45 seconds after it goes offline Search online devices manually Refresh You can also click al to refresh the online device list manually The newly searched devices will be added to the list 17 Network Camera Quick Operation Guide NOTE You can click or on each column heading to order gt gt t
4. 92 0 0 64 The default user name is admin and password is 12345 For accessing the network camera from different subnets please set the gateway for the network camera after you log in 19 Network Camera Quick Operation Guide 5 Accessing via WEB browser System Requirement Operating System Microsoft Windows XP SP1 and above version Vista Win7 Server 2003 Server 2008 32bits CPU Intel Pentium IV 3 0 GHz or higher RAM 1G or higher Display 1024x768 resolution or higher Web Browser Internet Explorer 6 0 and above version Apple Safari 5 02 and above version Mozilla Firefox 3 5 and above version and Google Chrome8 and above version Steps 1 Open the web browser 2 Inthe browser address bar input the IP address of the network camera e g 192 0 0 64 and press the Enter key to enter the login interface 3 Input the user name and password 4 Click HF 20 Network Camera Quick Operation Guide English v User Name admin Password eeeee Login Figure 5 1 Login Interface 5 Install the plug in before viewing the live video and managing the camera Please follow the installation prompts to install the plug in s NOTE You may have to close the web browser to finish the installation of the plug in 21 Network Camera Quick Operation Guide Live View Playback Log Configuration Please click here to download and install the plug in Close the bro
5. HIKVISION Network Camera Quick Operation Guide UD 6L0201B1191A01 www hikvision com Network Camera Quick Operation Guide Thank you for purchasing our product If there are any questions or requests please do not hesitate to contact the dealer About This Document This manual applies to DS 2CD2412F I W DS 2CD2432F I W series cameras This manual may contain several technical incorrect places or printing errors and the content is subject to change without notice The updates will be added to the new version of this manual We will readily improve or update the products or procedures described in the manual DISCLAIMER STATEMENT Underwriters Laboratories Inc UL has not tested the performance or reliability of the security or signaling aspects of this product UL has only tested for fire shock or casualty hazards as outlined in UL s Standard s for Safety UL60950 1 UL Certification does not cover the performance or reliability of the security or signaling aspects of this product UL MAKES NO REPRESENTATIONS WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT 0500051030809 Network Camera Quick Operation Guide Regulatory Information FCC Information FCC compliance This equipment has been tested and found to comply with the limits for a digital device pursuant to part 15 of the FCC Rules These limit
6. from the camera may reflect back into the lens causing reflection The cube camera can be installed on wall ceiling or table Ceiling mounting is taken as an example in this section if you adopt wall mounting or table mounting you can also take below procedure as a reference Steps 1 Open the cover on the mounting base from the bracket 10 Network Camera Quick Operation Guide Figure 3 1 Open the Cover 2 Stick the drilling template to the ceiling A Screw Hoe N Screw Hole Drilling Template SIN Screw Hole F S Figure 3 2 Drilling Template NOTE For cement ceiling mounting you need to use the expansion screw to fix the camera The mounting hole of the expansion pipe on the wall should align with the mounting hole of the drilling template 11 Network Camera Quick Operation Guide For wooden ceiling mounting you can just use the self tapping screw to fix the camera The ceiling must be strong enough to withstand more than 3 times the weight of the camera Drilling template Figure 3 3 Stick the Drilling Template 3 Use 3 screws to fix the bracket to the ceiling and the screw hole on the bracket should align with the mounting hole on the drilling template Figure 3 4 Fix the Bracket 4 Install the mounting base cover and attach the camera on the bracket 12 Network Camera Quick Operation Guide Figure 3 5 Install the Cover and Camera
7. he information you can click to show the device table and hide the network parameter panel on the right lt lt side or click to show the network parameter panel O Modify device information Steps 1 Select the device to be modified in the device list as shown in Figure 4 3 The network parameters of the device will be displayed in the Modify Network Parameters panel on the right side as shown in Figure 4 4 2 Edit the modifiable network parameters e g IP address and port number 3 Enter the password of the admin account of the device in Save the Password field and click to save the changes Total nunber of online devices 1 Refresh gt iD Device Type IPv4 Address Port Software Version iPv4 Gateway Serial No 001 DS XXXX XX 192 0 0 64 8000 VX X XbuildXXXX 192 0 0 1 XX XXXX XXXXXXXXXX Figure 4 3 Select a device 18 Network Camera Quick Operation Guide Modify Network Parameters IP Address 192 0 0 64 Port 8000 Subnet Mask 255 255 0 0 IPv4 Gateway 192 0 0 1 IPv6 Address as IPv6 Gateway i ti C SY IPv6 Prefix Length Serial No KXXXXXXXXXXXXXXXXXXXX Pa ssword Save 9 Note Enter the admin password of the device before you save the network parameters Figure 4 4 Modify Network Parameters 3 Enter the IP address of network camera in the address field of the web browser to view the live video x The default value of the IP address is 1
8. s are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity Statement This product and if applicable the supplied 3 accessories too are marked with CE and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC Network Camera Quick Operation Guide 2002 96 EC WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union For proper ma recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info Net
9. work Camera Quick Operation Guide Contents 1 Appearance Description cccccccscceescceesceeeeseesneeeseeeeenenens 5 2 NOP CGissiissinasttsaseprataniinsassaseceaisssieeneneRenniatEeARAERURian 8 3 TASEAU ATION ssssinssansssnscaneacnsaaseaaniaanscavsaanesanscanesancaaneaanens 10 4 Setting the Network Camera over the LAN ss000885 15 5 Accessing Via WEB brOWSe r sssssssnnnnnnnnnnnnnnnnnnnnnnnnnnn 20 Network Camera Quick Operation Guide 1 Appearance Description 9 10 N pr 4 6 wy E _ f a maaf 11 2 O Jtem aE S a a 2 Figure 1 1 Overview Table 1 1 Description Oe J e 4 Alarm Indicators Solid red when the camera is armed Solid blue when the camera is unarmed Network Camera a Operation Guide scription Status Reserved Link Flashing amber when network connection is functioning properly Unlit when no network connection es es ee e es e ee ee NOTE To reset the default parameters to the camera you need to press and hold the RESET button and power on the camera After the power on of the camera you must still press and hold the Reset button for about 10 seconds The WPS button is an easy configuration protocol of Wi
10. wser when installing the plug in Figure 5 2 Download Plug in Message from webpage i New version of plug in is detected Update it OK Cancel Figure 5 3 Download Plug in 22 Network Camera Quick Operation Guide Click Next to continue or Cancel to exit Setup Figure 5 4 Install Plug in eis e Setup Web Components Setup has finished installing Web Components on your computer Click Finish to exit Setup Figure 5 5 Install Plug in 23 Network Camera Quick Operation Guide 6 Reopen the web browser after the installation of the plug in and repeat the above steps 2 4 to login so NOTE For detailed instructions of further configuration please refer to the user manual of network camera 24 First Choice for Security Professionals Hikvision Digital Technology Co Ltd All Rights Reserved
Download Pdf Manuals
Related Search