Home
Infinity Owner`s Manual
Contents
1. Infinity Windows Care and Maintenance 19 Swinging Screen Removal It you live in a cold climate it is recommended that during the winter months you remove the screen door to avoid snow and ice trom collecting causing the mesh to sag lo remove the swinging screen door first open the active screen panel and disconnect the auto closer Remove the 6 x 1 2 screw attaching the closer to the head jamb bracket Then remove the hinge pins trom the active screen panel hinges remove the panel from the hinges and store On XX configurations open the passive screen panel and remove the hinge pins in the same manner as the active Adjust the closing tension on your swinging screen door by loosening the two screws attaching the door bracket to the screen panel Slide the bracket and closer left or right as needed and tighten screws Adjust the closing speed by tightening or loosening the adjusting screw located at the rear of the cylinder assembly Remove Screw Tension Adjustment 20 Care of PVD Finishes Care of PVD Finishes Hardware with a Physical Vapor Deposition PVD Finish Your PVD finished product has undergone a state ofthe art process known as Physical Vapor Deposition A layer of hard wearing metals are deposited onto the solid brass substrate which means it has been given a tough finish to resist fading and discoloration by direct sunlight humidity and most other environmental factors even in coastal areas lo help
2. Keep them dirt and grease free by washing with a gentle dish detergent Check the exterior caulking on your double hung windows annually How to Tilt Your Double Hung Windows for cleaning the glass To tilt the bottom sash unlock the unit and raise the sash about 4 Push down on the tilt button located on top ot the sash lock base Rotate the sash lock past the tilt button and ease top edge of bottom sash to a horizontal position 12 Infinity Windows Care and Maintenance To tilt the top sash lower the sash about halt way Pull the tilt latches inward located on the top edge of the sash rail simultaneously until they clear unit frame Ease top of sash to a horizontal position How to Remove the Double Hung Sash for replacement or repair To remove the sash tilt the bottom sash using the same technique described in the previous section E Larger sized sash can be heavy and awkward to handle To avoid injury use assistant to remove larger sash When sash is in a horizontal position litt both sides of the sash upward 2 3 51 76 mm raising pivot pins out of each clutch Now rotate the sash until pivot pins clear the jambs and remove the bottom sash trom the frame Next tilt the top sash using the same technique described above When the sash is in a horizontal position litt both sides upward 2 3 51 76 mm raising pivot pins out of each clutch Finally rotate the sash until the pivot pins clear the
3. Part Identification In the tollowing pages youll tind operation and maintenance intormation on Infinity from Marvin windows products Refer to EE Eh al the product illustrations for the names of your particular windows E and use the illustration below to help identity window components Side amo Check Rail Glass Sash EEE Frame Zh Rail Double Hung shown for illustrative purposes only 4 Windows Infinity Window Products Double Hung Glider Infinity Integrity Door Products Inswing French Door XO Inswing French Door XX Windows 5 Glass Condensation Before reading this section pour yourself a nice tall glass of ice water During cold winters there is a large temperature diference between the interior and exterior ot your home When the temperature drops outdoors the glass on your windows tend to have a lower surtace temperature than other surfaces in your home and is the first place that you ll notice condensation in your home This is not due to any detect in your window or door it s simply a sign ot needing to reduce the humidity in your home Warm air is capable of holding more moisture than cool air As warm vapor tilled air comes in contact with a cool surtace it looses its ability to hold moisture When moisture laden air reaches its dew point moisture condenses on the nearest cool surface Generally the most obvious surfaces in your home where youll notice condensation a
4. away from open window HER Freret JHR HI HH PETE HHTH HHEH AWARNING ssa Infinity Windows Care and Maintenance In the following pages youll find maintenance information on individual Infinity products Refer to the product illustrations for the names of your particular windows or doors Information in this section includes maintenance tips and operational tips such as removing the window sash Read completely through the instructions betore beginning to work on your windows to make sure you have any necessary tools and parts Exterior finishes on doors can be cared for in the same manner as Intinity windows See interior and exterior maintenance information Take care with your doors sill make sure you prevent damage by not getting any paint solvent or chemicals on sills See individual door sections for any specialized sill care T you are having problems not explained in this manual or it the solution seems inappropriate for your problem contact your local Infinity retailer When contacting your Infinity retailer it may be helptul to provide them with the Customer Service Serial Number etched on the upper right corner of the glass Customer Service Serial Number Low E3 366 option Customer Service Serial Number Standard Low E option Screen Care and Maintenance 11 Double Hung Window Operation and Maintenance Periodically clean the jamb liners where the sash slides
5. do this Important Adjustable hinges are not intended to compensate for an improperly installed unit Adjustments should only be made when panel misalignmentis visible or causes poor operation of door lock Make any adjustments in small increments check results readjust or proceed as required The vertical adjustment screw located on center hinge s has a range of 32 turns Horizontal adjustment screws located on top and bottom hinges have a turn range 1 Check panel clearance at sill and head jamb The panel should have 3 16 5 mm clearance at head jamb and at bottom 2 Align panel vertically as needed by rotating center hinge vertical V Phillips head adjustment screw The arrow on hinge indicates direction the stationary or jamb leat pin will travel in relation to operator panel adjustment leaf Check index mark on hinge leat near patent number and adjustment leat edge to determine amount and direction of panel movement See illustration 3 Check panel alignment with locking jamb panel should have 3 16 5 mm clearance along the jamb See illustration 4 Rotate horizontal adjustment screw clockwise to increase counterclockwise to decrease jamb panel clearance at the appropriate hinge ie if increasing clearance at top bottom hinge may have to be adjusted to decrease clearance to avoid hinge binding See illustration recheck latch and corrected After panel alignment is deadbolt operation
6. finish well with clear water after cleaning NOTE Stronger concentrations of cleaner may damage the coating surface or finish Always wear protective eyewear and skin protection when using an aggressive cleaning compound Screen Care and Maintenance The most effective method of cleaning the screens on your windows and doors is to remove the screens lay them on a flat clean area such as a sidewalk and spray off any dust or debris with water trom your garden hose Allow the screens to completely air dry before replacing in the window or door If you live in a cold climate it is recommended that in the winter you remove the screen trom your doors The mesh may collect snow and ice causing it to sag Please see individual sections for instructions on screen removal Contact your Intinity retailer it you require assistance with screen replacement NOTE Certain size screens have a factory bow in the frame this is to ensure a snug fit and is NOT a defect CAUTION Infinity screens are designed to stand up to everyday use However these screens were not intended to act as a satety device Do not allow children or pets to sit or play on window sills or to push or fall against window screens as this could result in a fall through the window or door opening Every screen installed on an Intinity product has a non removable label affixed to it that states WARNING Screen will not stop child from falling out window Keep child
7. jambs and remove the top sash trom the frame How to Replace the Double Hung Sash Hold the sash exterior side up with the top rail facing towards you Rotate and insert the sash so the sash pins clear the trame and place it so the lower sash pin is 2 3 51 76 mm above the clutch Rotate the sash to the horizontal position and lower it down until the pivot pins are fully seated into the clutches Simultaneously pull in on both tilt latches and tilt the sash up into place Release the tilt latches and operate the sash to ensure that the sash is operating smoothly Check sash pivot pins to ensure they are fully engaged in the clutch cams before proceeding Repeat above procedures for bottom sash except retract the sash check rail guides with the tilt button on the sash lock base when installing Infinity Windows Care and Maintenance 13 Resetting a Slipped Clutch Assembly Measure the clutch dimension trom sill on the opposing balance assembly tor the same sash and temporarily mark that dimension on the jamb carrier that contains the released clutch must be within 1 8 3 mm Using a flat screwdriver rotate the balance clutch cam in the clutch assembly to the released position Hold the screwdriver tirmly and slide the clutch assembly down the jamb carrier to the mark Rotate the balance clutch cam to the open locked position cam opening up Release the screwdriver carefully from the clutch assembly it must lock in place or d
8. paints stains or varnishes hese products contain solvents which when coming in even momentary contact with weather strip can cause it to become brittle and require replacement Examine window or doors interior and exterior finish Periodic cleaning and touchup can extend the life of your finish See repainting refinishing information on pages 8 through 10 Inspect exterior caulking around the outer edges of the window or door frame Irim off any loose caulking and reseal any gaps with a good quality caulk Check all hardware locks opening mechanisms etc for smooth operation Inspect exposed hardware screws tighten it loose Clean sand dirt or dust trom door and window hinges sills and tracks When soiled wash the exterior of your doors and windows with warm soapy water rinse with clean water and dry Hazard Notations Please tamiliarize yourselt with the tollowing hazard notations used throughout this manual lcon Description Usage Mistake or misuse could cause damage to the window or Caution 3 result in faulty installation and unit performance T Mistake or misuse could result in personal injury and or S severe damage to unit equipment and or structure Seah Asida Help from another individual is necessary to pertorm the task safely and correctly Information on alternative procedure definitions helpful Tips Hints bee Annual Window and Door Checklist 3 Windows Window
9. sure that any excess is immediately removed Sash track Remove and Install the Screen lo remove casement awning screen grasp screen litt Litt upward and draw screen towards you removing screen trom channel To install casement awning screen place screen into the upper screen channel Lift upward and push screen tight against frame Release screen lift to seat screen into place Round Top Polygon and Direct Glaze Maintenance Most Infinity Round Top and Polygon windows and all Direct Glaze windows are non operational meaning they do not open or close so there are no maintenance requirements for hardware or weather stripping Clean the glass occasionally and maintain the interior wood or exterior surfaces on the same schedule as your other windows Infinity Windows Care and Maintenance 17 Infinity Sliding French Patio Doors Operation and Maintenance The Patio and Sliding French Doors require very little maintenance to keep them functioning efficiently Most problems can be eliminated by keeping the sill clean ensuring smooth door operation Chemicals solvents paints and other harsh substances should never come in contact with the sill Remove any paint grease or caulk with DO isopropyl alcohol Door handles can be wiped down with a damp cloth to remove fingerprints and smudges It is very seldom that door rollers lock and hinges require lubrication Occasionally use spray lubricant to keep operation sm
10. the locking jamb or casing An even reveal should be achieved along the entire height of the jamb Integrity Swinging French Doors Operation and Maintenance Your French door requires very little maintenance lo maintain sill appearance wash with a mild soap and water solution Remove fresh paint splashes grease or caulk with 50 isopropyl alcohol You may wish to remove door panels for moving or other reasons f you need them removed please contact your Infinity retailer for either detailed instructions or for a service person to remove the panel for you Handle Operation for the Multi Point Lock Always close and lock your passive panel first and the operating panel with thumb turn second Integrity s multi point hardware has locking bolts at the head and base of the door Lifting the handle 45 degrees upward will set the head and foot bolts in place for a secure seal A 9O degree turn of the key from the outside or the thumb turn on the inside will lock the deadbolt in the handle assembly When the deadbolt is unlocked downward pressure on the handle will release the bolts and latch and the door will open Securely lock by engaging the deadbolt head and foot bolts using only one or the other does not offer full security Hinge Adjustment Procedures Should you find it necessary to make minor adjustments to your Integrity Inswing French Door atter it has been permanently installed the adjustable hinge system will allow you to
11. with tine sandpaper and wiping clean betore applying your choice of tinish Integrity uses a rubber like material between glass panes and wood sash trames to ensure a weather tight seal Occasionally an excess of this silicone sealant called squeeze out appears around the edge of the glass You can safely scrape off squeeze out with a plastic putty knite without damaging the weather tightness of your door It is extremely important that you do not paint locks hardware weather strip or jamb liners Also use paints stains and varnishes with care they contain solvents which when coming in contact with plastics and vinyl weather strip cause these materials to lose their flexible qualities Painting Use only a high quality oil base or latex paint lo provide a good adhesion of paint a compatible prime coat should be applied Paint with panels opened or removed do not close panels until thoroughly dry Apply one coat of primer and two coats of top quality paint according to the paint manufacturer s instructions CAUTION Do not apply paint to the Integrity factory pretinish without first contacting your Infinity dealer for proper instructions Staining Apply stain according to the manufacturer s instructions Apply as many coats of stain as necessary to achieve the desired color After the stain is thoroughly dry apply at least two coats of sealer i e varnish or polyurethane Prior to staining natural wood it is desir
12. INFINITY Rs lorn MARVIN REPLACEMENT WINDOWS Built for life Owners Manual Painting Staining Care and Maintenance Table of Contents Introduction aaa 2 Howto Uee ihe Mandadis aa Ea E E E EA aE A EE LAA EEE E R E EL A E L R L E E EE 2 S TTT 2 Annual Window and Door Checklist 3 PAZ are NOISES sry savbave cord pudbirag sed 2o4 EEEE EE E EEEE EE E md jendoaureu 3 Vies TTT 4 UO H aks ldeniiical ON nres reamed ineine anced E E EE E AEEA EEE E E E EA EE nese cannes 4 a e T See T A E E oc E E ET AT EET E E AT EEE E TTE J many 1 R e aa AAE A EEA E AE A sean AE AA E 3 eE E E E E et ee pete E ees oe 6 e a1 eE E E ple wana E E yu Geena E E E bot T E E ue oes C Interior Mildew oo EE Eee D Ere DE bbb debe bbb bbb bbb bbb bret bbb bbb bbb b ebb b bbb e nay D EE TTT 6 CeO le so ae cena sues cere bs ee cee E ye eee cin cite by be de gs eee ee es ee 7 ase re aN a E E EE EE EEE EEEE f Interior EverWood Finish 00 ccc ccc cece cence EE 8 Finishing or Painting Bare Interior Wood Integrity Swinging Doors 9 Ultrex inis 9 EN ca ok hn este a sh ada ed a ark nade bam ghey beak eer bo da gn cada dot he rd ach a eaten tn da ee 10 MEW EMC NOR SAC Soon cert utrinng ede rt conaneet Gunwusag ert nedceged sed eunowarseds oiceryasrt deunevaverd eters atieuse saves 10 Screen Care and Maintenance 11 Infinity Windows Care and Maintenance 0 0 0 ccc cece cece eee eee e eee e eens beeen nee e eens 11 Ke lt BR asia theta coa
13. Rinse off cleaning residue with warm water and let thoroughly dry For more difficult stains apply SP to a clean cloth and wipe soiled area clean Rinse off cleaning residue with warm water and let thoroughly dry For especially dificult stains or spills apply non abrasive Go Jo1016 to a clean cloth and wipe soiled area clean After cleaning rinse off cleaning residue with clear water and let thoroughly dry 8 Interior EverWood Finish Selecting and Applying a High Quality Gel Stain Read and follow gel stain manufacturer s instructions and warning for application preparation and cleanup Apply the gel stain with a brush in the direction ot the wood grain on the supplied test strip of EverWood to determine if the gel stain adequately matches your existing finish before applying stain to the unit If the stock gel stain applied to the EverWood test strip does not adequately match your existing finish it is possible to custom mix gel stains by adding colorants or combining colors The exact process will depend on the brand of gel stain you are using Intinity recommends contacting a stain paint specialty store to custom mix a matching color for your application After a good match has been obtained on a sample apply gel stain evenly with a brush to the window unit K 1 i Applying Water Based Polyurethane Top Coat Prior to staining natural wood it is desirable to apply a wood conditioner to obtain a more even finish F
14. able to apply a wood conditioner to obtain a more even finish Follow manufacturer s instructions Ultrex Finish The exterior and interior of Infinity Windows and the exterior of Integrity Doors are made of Ultrex an advanced glass fiber reintorced material Cleaning Ultrex Clean the Ultrex surface with a damp cloth soaked in warm water Wipe down with a dry cloth and allow the surface to thoroughly dry gt Any non abrasive household cleaner will not harm the finish CAUTION Do not allow Naptha to come in contact with EverWood material Repairing Ultrex You will need to supply Utility knife 120 150 grit sandpaper Quality exterior grade primer gt Epoxy putty gt Putty knife v 320 400 grit sandpaper NOTE Consult your representative for information on locally available epoxy putty 1 Using a utility knife carefully cut around the damaged Ultrex area to remove any jagged edges or loose tibers 2 Follow manufacturer s instructions for mixing blending of epoxy Fill the damaged area thoroughly by pressing epoxy in with a putty knife and remove excess 3 Once the epoxy has set and cured sand the repaired area with 120 150 grit sandpaper until the desired protile depth has been achieved Finish sanding with 320 400 grit sandpaper 4 Lightly sand the surrounding area to remove the factory finish with 320 400 grit sandpaper Coat the repaired and surrounding area with a quality prime
15. amage will occur Compare clutch heights from the sill for the sash affected They MUST be within 1 8 3 mm of each other or damage may occur when sash are reinstalled adjust height as needed T CAUTION Clutches are under extreme spring tension 14 Infinity Windows Care and Maintenance Removing and Installing the Screen lo remove the screen lift up the bottom sash to its fully raised position Grasp and pull inward on both plunger bolts and push outward on the screen Grasp the frame of the screen and pull down slightly on the screen until it clears the screen channel Turn the screen sideways and bring it in through the bottom sash opening lo replace the screen reverse the above procedure uii ee it i mee cla Glider Operation and Maintenance Periodically clean the tracks where the sash must slide Keep tracks dirt and grease tree clean surface with a damp cloth soaked in warm water and wipe down with a dry cloth allowing the surface to thoroughly dry Sash Removal Slide the operating sash to stationary side of the unit approximately 2 3 51 76 mm from stationary jamb With latches depressed located at the top of the sash tilt the sash inward until it clears the unit frame litt the sash off the sill track lo replace the sash reverse the above procedures NOTE Only the operating sash of a Glider can be removed from the frame Removing and Installing the Screen To remove the screen op
16. e trapped between the glass and the cleaning material Window and door gaskets sealants and trames are susceptible to deterioration it cleaning solutions are not rinsed and dried immediately after cleaning WARNING A Do not use razor blades knives or scrapers for cleaning glass surtaces Glass Care DOs and DON Ts DO DONT Clean glass when dirt and residue appear Use scrapers of any size or type for cleaning glass Determine if coated glass surfaces are exposed Allow dirt and residue to remain on glass for an extended period of time Exercise special care when cleaning coated glass surfaces Clean tinted or coated glass in direct sunlight Avoid cleaning tinted and coated glass surfaces in direct sunlight Allow water or cleaning residue to remain on the glass or adjacent materials Start cleaning at the top of the building and continue to lower levels Begin cleaning without rinsing excessive dirt and debris Soak the glass surface with a clean water and soap solution to loosen dirt and debris Use abrasive cleaning solutions or materials Use a mild non abrasive commercial window cleaning solution gt Allow metal parts of cleaning equipment to contact the glass Dry all cleaning solution trom window gaskets sealants and trames Trap abrasive particles between the cleaning materials and the glass surtace Clean one small window and ch
17. eck to see if procedures have caused any damage Allow splashed materials to dry on the glass surface Glass 7 Interior EverWood Finish Before You Begin Read these instructions thoroughly betore beginning to stain or paint your Infinity window Once finished it is very difficult to remove the stain or paint and retinish the unit EverWood Interior Stainable paintable Infinity products feature EverWood an interior engineered wood grain surface that requires a paint or gel stain finish to be applied before or immediately after installation CAUTION When applying gel stain or paint finish avoid contact with plastic or vinyl parts such as weather strip hardware handles or rollers Plastic and or vinyl parts that have had contact with paints stains or polyurethane will eventually become brittle and may require replacement DO NOT sand or use abrasive cleaners on EverWood DO NOT allow EverWood to come in contact with petroleum distillates such as benzene toluene or kerosene DO NOT allow EverWood to come in contact with silicone or other adhesives prior to finishing Finishing or Painting EverWood Preparing and Cleaning the EverWood Surface Clean the EverWood surface with a damp cloth soaked in warm water Wipe down with a dry cloth and allow the surface to thoroughly dry Ifthe surface has become soiled try cleaning with a mild detergent such as 409 applied to a damp cloth
18. en the operator sash completely Grasp the screen pull tabs located on the jamb stile side of the screen Pull the tabs toward the center of the unit until the screen frame can clear the screen channel Push the screen out to the exterior and turn diagonally to bring into the dwelling Replace the screen with the operator sash completely open and position the screen on the exterior of the window with the springs toward the meeting stile of the unit Making sure the springs are seated in the screen channel pull on side tabs until the screen clears the frame Pull screen in toward the interior until the jamb stile of the screen aligns with screen channel release tabs a E Sash pull NOTE Pull tab away from frame and then push out Infinity Windows Care and Maintenance 15 Casement Operation and Maintenance The roto gear is the operating mechanism that you crank to open and close your casement and awning windows Your casement lock seals the window tightly closed Excessive cranking when closing your window does not improve the seal and may damage your roto gear Roto gears should be lubricated once a year with white lithium grease available at any hardware store to keep operation smooth The hinge joints and locking mechanism should be lubricated on occasion with a silicone based spray Be sure to clean of all dirt debris or sand betore lubrication CAUTION Excessive lubrication may cause damage to the fin
19. eyewear and skin protection and keep the area well ventilated Make sure the surface is clean and reapply if the discoloration persists Tempered Glass Certain Infinity windows use tempered glass for safety reasons Tempered glass is heated and cooled at an accelerated rate adding strength and shatter resistance You may notice a slight amount of distortion this is normal and due to the tempered glass tabrication process Ihe logo in the corner of each piece of tempered glass is required by code and safety regulations Glass Breakage Should the glass in your window or door happen to break make sure you use the appropriate personal protection equipment to remove the broken glass eyeglasses or goggles sturdy gloves and heavy protective clothing Dispose of broken glass in a secure container Failure to properly handle and dispose of glass could result in injury Contact your Infinity retailer tor information on sash or panel replacement Cleaning the Glass The best method to clean the glass on your Infinity window is to first soak the glass surface with a clean water and soap solution to loosen dirt or debris Use a mild non abrasive window washing solution and apply with a non abrasive applicator Immediately atter washing the glass remove all of the cleaning solution with a squeegee taking care not to allow any metal surface of the cleaning equipment to touch the glass surtace Make sure that no abrasive particles ar
20. g jamb is shimmed plumb and level 5 Check panel operation If satisfactory replace adjustment hole caps Removing the Screen lo remove the screen panel unlock and partially open the screen door From the exterior pry the screen panel guide up with a putty knife starting at one corner Pull the guide off the track working your way toward the other end Once the bottom of the screen panel is completely released trom the sill track pivot the bottom of the screen out and push the top of panel approximately 5 degrees toward the head jamb Top adjustment screw Screen Track Screen Roller This will release the screen panel rollers trom the head jamb screen track Remove the panel trom the door To reinstall the screen hold the screen panel with the top rollers facing you While tilting the bottom of the screen panel away trom the door lift the rollers into the screen track and pull the panel toward your body to engage the rollers in the track Make sure the rollers are seated in the track by moving the screen panel back and forth Once you are sure the rollers are fully seated pivot the screen panel into position toward the sill and place the bottom screen panel guide into the sill track by lifting it with your fingers or by lifting with a stif putty knife The screen can be adjusted from the interior by loosening or tightening the top roller screw nearest the locking jamb Adjust the screen so that it is parallel to
21. ish of your window Avoid getting oil and solvents on your finish Make sure that any excess is immediately removed The sash tracks should be occasionally cleaned out with a soft bristle brush If your casement is less than 24 3 8 721 mm in width your roto gear arms and assembly may differ trom those shown Interior and exterior finishes can be cared for in the same manner as any other Infinity window or door See interior and exterior maintenance information on pages 8 10 Removing and Installing the Screen lo remove casement awning screen grasp screen litt Litt upward and draw screen towards you removing screen trom channel To install casement awning screen place screen into the upper screen channel Lift upward and push screen tight against frame Release screen lift to seat screen into place Screen litt 16 Infinity Windows Care and Maintenance we Crank handle Awning Operation and Maintenance Awning hinges roto gear operator arms and sash tracks can be oiled with a few drops of light household oil or silicone spray Operating hardware should be lubricated during your annual inspection Simply crank open the window and lubricate hardware with white lithium grease Interior and exterior finishes can be cared tor in the same manner as any other Infinity window or door CAUTION Excessive lubrication may cause damage to the finish of your window Avoid getting oil and solvents on your finish Make
22. ollow manufacturer s instructions Read and follow the polyurethane manufacturer s instructions and warnings for application surface preparation and clean up After letting the gel stain dry overnight test an inconspicuous area to see it the surtace is dry by wiping the stained surtace with a clean cloth T stain appears on the cloth the stain needs to dry longer before applying the polyurethane top coat Atter the stain has completely dried use a clean brush to apply a top coat of high quality water based polyurethane Lightly sand the surface with 400 grit sandpaper taking extra care not to sand through the polyurethane surface and apply one more coat of high quality water based polyurethane Applying a Paint Finish Read and follow the paint manufacturer s instructions and warnings for application preparation and clean up TEST a high quality latex or oil based paint applied in the direction of the wood grain on a sample piece of EverWood before applying paint to the unit NOTE EverWood does not require the use ofa prime coat One coat of high quality paint generally provides adequate coverage Finishing or Painting Bare Interior Wood Integrity Swinging Doors lt you have a brand new bare wood Integrity door you must finish it immediately to prevent possible damage to the wood Make sure bare wood door interior surtace is clean and dry Remove any handling marks debris or effects of exposure to moisture by sanding lightly
23. ooth rollers are visible underneath the operator panel If you live in a cold climate it is recommended that you remove the screen door in the winter The screen mesh may collect snow and ice causing it to sag Removing Sliding Door Panels Removing door panels is a relatively complicated procedure lf you need them removed please contact your retailer for a service person to remove the panel for you Panel Adjustment Procedure Should you find it necessary to make minor adjustments to your Infinity Sliding Patio or Sliding French door after it has been permanently installed panel adjustment will allow you to do this Tools needed Small putty knife Standard scredriver 2 Philips screwdriver Using small putty knife or standard screwdriver remove two roller adjustment hole caps trom bottom rail ot operating panel 2 Slide operating panel 1 2 3 4 away trom locking jamb 3 Adjust rollers to raise lower panel by turning adjustment screws with standard screwdriver See illustration 1 Open panel slightly and align panel to lock jamb to get an even reveal and maintain equal clearance at top and bottom between head jamb and sill See illustration 2 Adjustment screw for rollers Slide Operator panel open Adjust until even reveal Illustration 1 Illustration 2 18 Infinity Windows Care and Maintenance 4 f an even reveal is unobtainable along entire length of panel ensure lockin
24. ows Intinitys exterior to withstand extreme temperatures atmospheric pollutants while retaining its color and gloss This translates into a beautiful low maintenance exterior Surface dirt can be removed by washing with a mild detergent and rinsing with clear water Use a soft brush such as a long handled car washing brush to remove any bugs grime dirt or dust Before using more aggressive cleaners on stubborn stains test the solution on an inconspicuous area before washing A thorough clear water rinse should follow Mildew Exterior Surfaces Mildew is a fungus that is most common in geographical areas near water such as the East West and Gulf Coasts the Great Lakes area rivers valleys and other areas of high humidity Mildew thrives on warmth and moisture and will grow best under these conditions However mildew can grow to some degree under most climatic conditions Mildew growth is usually brown or black in color and for this reason may be mistaken for dirt The presence of mildew can be contirmed by placing a drop ot household bleach on the suspected mildew area If small gas bubbles develop in the droplet of bleach mildew does exist and can be removed with the following solution Use this solution to help control exterior mildew 1 3 cup powder laundry detergent 2 3 cup trisodium phosphate TSP quart household bleach 3 quarts of water Apply solution with a soft bristle brush using medium pressure Rinse the
25. r per epoxy manufacturers instructions When primer has dried and cured cover with a quality exterior grade acrylic latex coating See Painting Ultrex Finishing or Painting Bare Interior Wood Integrity Swinging Doors 9 Ultrex Refinish Information Painting Ultrex You will need to supply 320 400 Grit sandpaper e Masking tape Foam paint brush Quality exterior grade acrylic latex paint Spot test a small area using the following procedures After the seven to ten day acrylic latex paint cure time check to see if the paint has adhered to the unit If the paint has not adhered to the surface recheck the surface preparation procedures 1 Thoroughly sand the factory finish with 320 400 grit sandpaper 2 Wash the surface with water and detergent to remove contaminants rinse with clear water and dry thoroughly 3 Mask any window components that will not be painted 4 Coat the Ultrex with a quality exterior grade acrylic latex paint 5 Acrylic latex products gain full adhesion after seven to ten days cure NOTE If the finish is scratched peeled or otherwise compromised down to the Ultrex substrate see previous page on repairing Ultrex 10 Finishing or Painting Bare Interior Wood Integrity Swinging Doors Exterior Care Infinity products feature Ultrex an advanced glass fiber reinforced material with a finish coat applied during the fabrication process This factory applied durable finish all
26. re on your windows or the glass of ice water sitting in tront of you Condensation on your windows is an unsightly problem The last thing you want is a tog blocking the view But the problem goes deeper than that it condensation is a chronic occurrence in your home chances are that you have excessive humidity It water is accumulating on glass chances are it is accumulating on other harder to see surfaces such as wall and root cavities It lett uncontrolled excess moisture can have serious consequences including Mold or mildew Wood rot and warping Root ice build up Damp ineffective insulation Discolored blistered or bubbling paint e Damaging moisture inside walls and attic Excessive interior humidity is more likely to occur in newer or recently remodeled homes with tight energy eficient construction causing a build up of moisture to the interior Information on excessive humidity and how to reduce condensation on your windows can be found on the Internet by searching tor window condensation 6 Glass Interior Mildew lt your home has excessive interior moisture you may experience some discoloration on building materials in various parts of your home including the lower portions of your windows or doors This discoloration may be the result of mildew growth and can be removed with Tilex or with regular laundry bleach on a sponge mix one cup of bleach to one gallon of water Warning Wear protective
27. retain the appearance of your PVD products for many years to come a little periodic maintenance is required to remove any atmospheric deposits from the surface of the product Once every two months clean the surface of the product thoroughly with a soft cloth moistened with light soapy water o remove heavier deposits a soot of non abrasive kitchen cleaner may be used with a moistened cloth Remove traces of water and cleaner and dry thoroughly with a soft cloth e When using any proprietary cleaner always follow the advice given by the manufacturers in handling cleaning materials Do not use any abrasive cleaning materials or solvents when cleaning your PVD products INFINITY E o MARVIN REPLACEMENT WINDOWS Built for life Call t800 372 1072 for the Infinity from Marvin installing retailer nearest you In Canada call 1800 263 6161 Or visit us at infinitywindows com Warroad MN U S A 56763 2014 Marvin Windows and Doors All rights reserved Registered trademark of Marvin Windows and Doors ENERGY STAR and the ENERGY STAR certification mark are registered U S marks Part 19970331 August 2014 Product specitications subject to change without notice Printed in U S A on recycled paper with at least 10 post consumer waste fiber MADE IN AMERICA r
28. rvin is committed to bringing you products of the highest quality and value Our made to order manufacturing philosophy is one example of our commitment Our warranty another Please visit the warranty section of our website www intinitywindows com Warranty for full warranty details on your product Registration To obtain the Limited Lifetime Warranty you must register your products with Infinity within sixty 60 days of product installation by completing the Warranty Registration form available at www intinitywindows com Warranty You may also register by calling 800 533 6898 If you do not register your products within sixty 60 days of installation you will not receive the Limited Lifetime Warranty instead you will receive the 10 20 Limited Warranty 2 Introduction Annual Window and Door Checklist Use this checklist as a maintenance reminder for your windows and doors to help keep your product operating properly and prevent future problems Once a year should be sufficient L J L J D D O U E Safety first use caution on ladders and wear protective eyewear and clothing When working with primers paints stains cleaning solutions etc make sure that you use and dispose of these materials according to local codes or manufacturer s instructions Inspect weather strip for damage or loss of performance Contact the local Infinity retailer if your weather strip requires replacement lake care when using
29. t tse E E dust ayadmessededyeaeaehae cheaerardedues eeteeds onuem yess E 12 Ei E E teas Ge eer Gye ss ET E E ee eee E EEEE 15 Eo o o tenes oasandeapetpaamadieaeduasiad cape seeas addons svawes TETE TE ETE EE 16 P EE EEE EEEE E E EEEE E EEEE 17 RE R gonna D Bike ne i he ee er ee eee ree 1 7 IEE ICING S E TTT 18 Integrity Swinging French Doors ccc ccc EEEE bbb ebb bbb bbb b ebb EEEE 19 Care of PVD Finishes 0 0 0 0 c cece cece cece cece eevee eee e vente bees te bt bevennanenennags 20 INFINITY E o MARVIN REPLACEMENT WINDOWS 2014 08 29 19970331 Built for life Introduction Thank you for your recent purchase of Infinity from Marvin windows and doors Infinity Replacement Windows are durable beautiful and low maintenance It s a claim were proud of and a fact youll appreciate as our windows serve you for many many years How to Use this Manual This manual was created to teach you a few of the basics about your new Infinity windows lake a few minutes to flip through this manual You ll find photos to help you identity your Infinity products general information on cleaning and answers to common questions There are also simple small things you can do to ensure years of perfect service It you have a question or experience a problem with your windows that is not mentioned in this manual just call your local Infinity retailer for help or visit our web site www intinity com Warranty Infinity Replacement Windows trom Ma
Download Pdf Manuals
Related Search
Related Contents
Manual Proprietário Bedienungsanleitung UCI Härtemessgerät PCE RèGLES DE SéCURITé - Regione Autonoma Valle d`Aosta Gear Head FS4100RED Fold `N Go® デウォルト電動工具 取扱説明書 DC900K 36V充電式 振動/ドリル Active Mini-Reference Monitors User manual ダウンロード - 株式会社クレファ Copyright © All rights reserved.