EXTECH Model DL150 user manual
Contents
1. EXTECH Model DL150 user manual http www manuallib com file 2693250 From ManualLib com ManualLib com collects and classifies the global product instrunction manuals to help users access anytime and anywhere helping users make better use of products Home http www manuallib com Chinese http www shuomingshuku com User s Guide EXTECH INSTRUMENTS A FLIR COMPANY True RMS AC Voltage Current Datalogger Model DL150 This Manual http www manuallib com file 2693250 Introduction Congratulations on your purchase of this Voltage or Current datalogger With this meter you can monitor and log data over long periods of time and then easily transfer the data to a pc for viewing and evaluation The LCD display provides real time data Max Min data and time information This meter is shipped fully tested and calibrated and with proper use will provide years of reliable service Safety A Warning Do not attempt to make measurement in flammable gaseous areas When testing a non insulated cable pay attention to avoid short circuits Do not attempt to use the instrument when your hand is wet Do not input over range during measurements Never open the battery cover during measurements Stop using the instrument when there is any structural defect or exposed metal parts Do not install substitute parts or make modifications on the meter Never replace the battery in moist areas Ens2. When the memory is full the data will overwrite the oldest data Memory full and recording has stopped LZ Battery sign when display completely the battery power is full When there is only a frame icon displayed the battery is exhausted and should be replaced with a new one 3 DL150 EU EN V2 4 3 12 2 AC adaptor Jack 3 ON OFF Button 4 MAXIMIN Press the button one time to display the MAX maximum reading Press again to display the MIN minimum reading A third press will exit MAX MIN mode The meter will automatically exit MAX MIN mode in 10 seconds if no button is pressed 5 CH Input Jack Insert the current or voltage sensor to this COM to measure and record the data 6 PEAK HOLD In the non PEAK measurement mode press the PEAK HOLD button to display the average Peak value of the present value Press the button again to exit PEAK display The meter will automatically exit in 10s if no button is pressed 7 START STOP Press the START STOP button for one time to pause data Press again to resume After setting the record mode press this button for more than 4 seconds and then release it after REC is shown on the LCD The meter will measure and record data according to the software setup 8 USB Port 9 AC Current Clamp Jaw Clamp the jaws around a single conductor for AC current measurements to 200A 10 Jaw Opening Trigger 11 CH Plug 12 AC Voltage Probes or Alligator clip
3. ight 2012 Extech Instruments Corporation a FLIR company All rights reserved including the right of reproduction in whole or in part in any form www extech com 6 DL150 EU EN V2 4 3 12 This Manual http www manuallib com file 2693250
4. ions to install the driver System Required Windows 2000 or Windows XP or Vista Minimum Hardware Required PC or NoteBook with Pentium 90MHz or higher 32 MB RAM At least 7 MB byte hard disk space available to install Datalogger USB software Recommended display resolution 1024X768 with High Color 16 bit Software Operation The Software operation is described in the HELP file located on the software disk 5 DL150 EU EN V2 4 3 12 This Manual http www manuallib com file 2693250 Specifications Display Maximum data points Channels Sample rate Transient capture Analysis software Data output Open input indication Low battery indication Power supply Battery life AC Adaptor Standards Operating Temperature Operating Humidity Current Clamp Jaw opening Multi function LCD 16 350 Voltage and 16 350 Current values Single channel TRMS AC Voltage or Current 1s to 24h selectable gt 0 244mS 2000 XP Vista USB port LO appears on the LCD Empty battery symbol appears on the LCD 4 AAA Batteries and 1 CR 3V memory button battery CR2032 or equivalent 5 days approximately 9V 0 5A CE cat ii 600v 0 to 50 C 32 to 122 F lt 70 RH 12 7mm 0 5 Dimensions 114 x 63 x 34mm 4 5 x 2 5 x 1 3 Weight 248g 8 70z Range Accuracy Voltage 10VAC to 600 0VAC 2 0 41V 40Hz to 1kHz Current 10A to 200 0A 2 0 1A 50 60Hz Peak Measurement 8 0 to 850 0V 5 0 Copyr
5. s 13 Voltage module 14 CH Plug 4 DL150 EU EN V2 4 3 12 Operation 1 2 3 4 Install 4 fresh AAA batteries or connect the AC adaptor Set up the datalogger using the software provided Connect the voltage test leads or the current probe to the AC source to be measured Press and Hold the START STOP button for four seconds to start recording The REC icon will appear in the display indication that recording has begun Press and Hold the START STOP button for four seconds to stop recording The REC icon will disappear from the display Remove the probe connect the datalogger to a PC and use the supplied software to download the data You as the end user are legally bound Battery ordinance to return all used batteries and accumulators disposal in the household garbage is prohibited You can hand over your used batteries accumulators at collection points in your community or wherever batteries accumulators are sold Disposal Follow the valid legal stipulations in respect of the disposal of the device at the end of its lifecycle Note If the clock does not set to the correct time replace the 3V button battery Software Introduction Place the CD in the drive and then follow the on screen installation instruction After the software is installed keep the CD in the drive and connect the datalogger to the PC by the USB cable A USB Driver installation window will pop up Follow the direct
6. ure the meter is disconnected and switch off before opening the battery cover to replace the battery Do not attempt to place the instrument in high vibration areas Do not expose the meter to direct sunlight high temperature and high moisture environment Switch off the meter after use Remove the AAA batteries when the meter will be stored for a period of time When cleaning do not use abrasives or solvents on the meter use a damp cloth and mild detergent only 2 DL150 EU EN V2 4 3 12 This Manual http www manuallib com file 2693250 Description and Button Functions 1 LCD Description 080DAN Normal record mode is selected DATE f i PEAK TIME INRUSH Capture record mode is selected Records the sine REC Hy Ha n mAV Hz wave when the measure value exceeds the Capture Y yi Y X Detection set level A fi A Auto power off setting the meter will automatically be VN he A shuts off after 5mins without any button presses MAX MI L DATA Average peak measure and record mode selected f about 195ms REG Recording status After the record mode is set up by the software press the START STOP button for more than 4 seconds to begin recording This icon will be displayed and indicates the meter is recording data Press the same button again for more than 4 seconds to stop recording Record until full is selected When the memory is full the datalogger will stop recording Continuous recording is selected
Download Pdf Manuals
Related Search