Home

Hanson QUATTRO MANUAL V1 0

1. Rigging POWER POWER INPUT OUTPUT POWER POWER INPUT OUTPUT oe POWER POWER INPUT OUTPUT i MA You can power link up to ten 10 QUATTRO fixtures on a 120 VAC 20 AMP or up to twenty 20 QUATTRO fixtures on a 240 VAC 20 AMP circuit The power linking diagram shown above corresponds to the North American version of the fixture ONLY If using the fixture in other markets you must consult with the local Hanson ProSystems dealer or distributor because power linking connectors and requirements may differ in your country or region Before deciding on a location for the fixture always make sure there is easy access to the fixture for maintenance and programming purposes Make sure that the structure or surface onto which you are mounting the fixture can support the fixture weight Refer to the Technical Specifications section of this manual for weight information When mounting the fixture overhead always use a safety cable Mount the fixture securely to a rigging point whether an elevated platform or a truss When rigging the fixture onto a truss you should use a mounting clamp of appropriate weight capacity The bracket has holes which is appropriate for this purpose When power linking multiple fixture you must always consider the length of the power linking cable and mount the fixture close enough for the cable to reach e The bracket adjustment knobs allow for directional adjustment when aiming the f
2. BATTERY _ CHARGE SAFETY INDICATOR BRACKET ON OFF ON OFF SWITCH SWITCH ON OFF CHARGE FOR TRANSCEIVER FOR AC SWITCH A der ales l SOUND SENSITIVITY LED DISPLAY KNE TRANSCEIVER LED amp SELECTOR 1 FUSE POWER POWER DME DMN FUNCTION HOLDERS IN CMT IN DUT l BUTTONS DUAL MOUNTING BRACKET Hanson ProSystems www hansonprosystems com User Manual Page 7 of 28 Hanson ProSystems www hansonprosystems com User Manual Page 8 of 28 HPS BPWDMXLED QUATTRO Features Battery Powered 8 Wireless DMX Rechargeable Battery with up to 12 hours of battery life Digital battery power indicator 0 100 Wireless DMX 512 protocol Built in 2 4G transceiver for wireless DMX operation Optional WDMX 126 auto jumping channel frequencies with high anti jamming ability to ensure work reliability 7 1D codes for multiple transceiver use Wired DMX 512 protocol Ability to send DMX protocol from the DMX output of the Quattro using a standard DMX cable to any generic DMX fixtures when using the Quattro fixture wireless 3 pin and 5 pin DMX input and output connectors Optional 5 pin DMX RGBWA color mixing Optional RGBA or RGBW 11 4 in1 Watt LED 6 RGBW 5 RGBA 25 degree lenses Optional 15 45 60 lenses Electronic Dimming 0 100 Operation menu with function buttons and DMX control mode LED display for address and function setting Control DMX channels 6 12 45 or 51 CH Full linear pixel mapping c
3. and 14 for all the different standalone modes Wired Master Slave Configuration This function will allow you to link together and operate without a DMX controller In Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units programs Any unit can act as a Master or as a Slave 1 Using approved DMX data cables daisy chain your units together via the XLR connector on the rear of the units Remember the male XLR connector is the input and the female XLR connector is the output The first unit in the chain master will use the female XLR connector only The last unit will use the male XLR connector only For longer cable runs we suggest a terminal at the last fixture 2 Onthe Master unit press lt MENUS gt then use the lt Up gt or lt Down gt buttons to find nASE on the menu display screen press the lt ENTER gt button use the lt Up gt or lt Down gt buttons to select Yes on the menu display screen then press lt ENTER gt 3 On the Slave units press lt MENU gt then use the lt Up gt or lt Down gt buttons to find nASE on the menu display screen press the lt ENTER gt button use the lt Up gt or lt Down gt buttons to select No on the menu display screen then press lt ENTER gt The Slave units will now follow the Master Unit Hanson ProSystems www hansonprosystems com User Manual Page 21 of 28 HPS BPWDMXLED QUATTRO Wireless Master Slave C
4. code frequency for the fixture by pushing down the selector button This will change colors to represent different ID codes frequencies See page 25 for ID codes frequencies and diagram Select a color ID code frequency for the fixture Keep in mind that ID code red is your starting point on the transceiver HPS DMX WTR Gently pull out the built in wireless antenna This is located on the right side of the fixture next to the Receiver Frequency Selector button and the LED indicator See below diagram for location Connect the transceiver HPS DMX WTR to a suitable power outlet Locate the ON OFF switch and turn on the unit On the front of the HPS DMX WTR transceiver unit you will find two different buttons labeled PA and ID PA is for the Wireless DMX distance and we recommend to always leave on 3 ID is to select the ID code frequency to match the color code on your fixture See page 25 for ID codes frequencies and diagram Select the ID number that matches the color code on the fixture Using a standard DMX controller run a DMX cable from the DMX out of the controller to the DMX in of the transceiver HPS DMX WTR Now your fixture and transceiver HPS DMX WTR will communicate and the LED indicator located under the Receiver Frequency Selector button will flash green If there is no signal the LED indicator returns to the original color you selected The wireless HPS DMX WTR transmitter can reach 400 500 meters which would be about 1
5. fixture in one of the standalone modes to control without a DMX controller Never connect a fixture that is operating in any standalone mode to a DMX string connected to a DMX controller The fixture in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller To enable the Standalone Modes do the following steps 1 Connect the fixture to a suitable power outlet or use the internal battery 2 Turn the fixture on 3 Unlock the fixture menu display by holding down the Up and Down buttons for 5 seconds the word Yes will appear on the menu display Then the fixture will be unlocked and ready to change settings For more information see page 13 4 Press lt UP gt repeatedly and CG CU CP NANU STOB SOUD and DENO will show on the menu display Once one of these modes Is selected the fixture will start to correspond to that mode Press lt ENTER gt to adjust the speed of the mode Press lt UP gt or lt Down gt and select the speed you desire Press lt ENTER gt and now your mode and speed will correspond as desired Press lt MENU gt to return to the previous menu ed See Menu Map on page 13 and 14 for all the different standalone modes Certain programs will have additional functionality To find these options press lt ENTER gt after selecting an auto program Then press lt UP gt or lt DOWN gt Not every program will feature all the added functionality See Menu Map on page 13
6. that shipped with it Therefore if the received merchandise appears to have damages caused during shipping the customer must submit the damage report and any related claims with the carrier not Hanson ProSystems The customer must submit the report upon reception of the damaged merchandise Failure to do so in a timely manner may invalidate the customer s claim with the carrier For other issues such as missing components or parts damage not related to shipping or concealed damage the customer must make claims to Hanson ProSystems within seven 7 days of receiving the merchandise Hanson ProSystems www hansonprosystems com User Manual Page 29 of 28 HPS BPWDMXLED QUATTRO 9 Manufacturer s Limited Warranty Hanson ProSystems hereby warrants to the original purchaser Hanson ProSystems products to be free of manufacturing defects in material and workmanship during the specific period from the date of purchase see specific warranty period on reverse this warranty shall be valid lt is the owner s responsibility to provide dated proof of purchase at the time of service In cases where a greater than a 12 month difference between date of manufacture and date of purchase the date of manufacture will be used as the warranty period start date This warranty is not transferable Purchase of Hanson ProSystems products from an unauthorized reseller excludes you from any Hanson ProSystems warranty A For warranty service you must contact Ha
7. 00 255 G000 255 Press Up Down to alter the value press enter Hanson ProSystems www hansonprosystems com User Manual Page 13 of 28 HPS BPWDMXLED QUATTRO O ii Blue manual operation 000 255 B000 255 Press Up Down to alter the value press enter for next color option White manual operation 000 255 Press enter Up Down to alter the speed press enter for next strobe option Amber manual operation 000 255 A000 255 Press enter Up Down to alter the speed press enter for next strobe option White Strobe 001 255 Press Up Down to alter the speed press Standalone Modes enter for next strobe option Color Strobe STOB STROBE 001 255 Press enter for SO1 press Up Down to change to SO2 Color Change Sound activation built in program So001 Press enter for SO2 press Up Down to Standalone Modes change to SO1 Color Strobe SOUD SOUND Sound activation built in program Press enter for SO2 press Up Down to change to SO1 Auto running mode D01 D12 Speed SP001 SP 99 Standalone Modes Fade FA00 FA99 DO1 D12 Press enter then Up Down to select a desired Demo chase To alter the speed press enter then Up Down to select a desired speed Master and slave setting Press enter then Up Down to select Yes or No WO00 255 DENO DEMO EFFECTS nASE MASTER MODES YES Slave NO Battery life indicator 0 100 Press enter to view battery life CoLo BUILT IN COLORS C01 C31 indicator will start at 00 00 VE VERSION
8. 312 feet in the case of no barriers And with barriers the signal can be reached 150 meters which would be about 492 feet This will vary according to the surrounding conditions TRANSCEIVER a FREQUENCY SELECTOR SS ANTENNA l l l l l l l l LED INDICATOR l l l l l l l PA ID CODE Hanson ProSystems www hansonprosystems com User Manual Page 24 of 28 HPS BPWDMXLED QUATTRO HPS BPWDMXLED QUATTRO Example 3 Examples of System Configurations Example 1 AL Ta AA AR Ai ES DMX TN CABLE LLL mas SIGNAL TRANSMITTER me DMX CONTROLLER RECEIVER Example 2 DMX CONTROLLER WIRED DMX FIXTURE Hanson ProSystems www hansonprosystems com User Manual Page 25 of 28 Hanson ProSystems www hansonprosystems com User Manual Page 26 of 28 HPS BPWDMXLED QUATTRO HPS DMX WTR Features e Single key to operate tricolor LED displaying e Transmitting standard DMX512 protocol data of DMX console It can also transmit fixture to fixture DMX512 protocol data 126 channels auto jumping frequencies high anti jamming ability to ensure work reliability 7 ID codes User can use 7 groups individual wireless net without interfering with each other in the same place Input voltage 5VDC Work frequency section 2 4G ISM 126 channels frequency section Max transmitting power rate 20dBm Receiver sensitive 94dBm Signal port RS
9. 485 or CPU series port AURT 7 Other information Cleaning Due to fog residue smoke and dust cleaning the internal external optical lenses and mirror should be cleaned periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates i e smoke fog residue dust dew In heavy club use we recommend cleaning on a monthly basis Periodic cleaning will ensure longevity and a crisp light output Instructions Use normal glass cleaner and a soft cloth to wipe down the out side casing Use a brush to wipe down the cooling vents and fan grill Clean the external optics and mirror with the glass cleaner and a soft cloth every 20 days Clean the internal optics with glass cleaner and a soft cloth every 30 60 days Always be sure to dry all parts completely before plugging the fixture back in aS eS Hanson ProSystems www hansonprosystems com User Manual Page 27 of 28 HPS BPWDMXLED QUATTRO Trouble Shooting Below i will find common pd de na encounter aa with Hee solutions For more No light output from the Fixture Be sure you have connected your fixture into a standard 120v wall outlet Check to ensure that the external fuses are not blown and that the fuse holders are completely and properly seated The fuses are located on the rear panel of the fixture Check that the battery has charge Fixture does not respond to DMX Check that the DMX cables are connected properly and are wi
10. 55 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 The seventh group The eight group The ninth group The tenth group The eleventh group 51 Channel Advanced Pixel Mapping Modes HPS BPWDMXLED QUATTRO Green 0 100 Blue 0 100 White 0 100 Red 0 100 Green 0 100 Blue 0 100 Amber 0 100 Red 0 100 Green 0 100 Blue 0 100 White 0 100 Red 0 100 Green 0 100 Blue 0 100 Amber 0 100 Red 0 100 Green 0 100 Blue 0 100 White 0 100 Remote Shut Off Remote fixture Hanson ProSystems www hansonprosystems com User Manual Page 18 of 28 on off via DMX control 3 channel 7 channel 8 channel 10 channel 11 channel 12 channel 13 channel 14 channel Channel Values HPS BPWDMXLED QUATTRO Function Red Green Blue White Master Intensity 0 100 Red Green Blue Amber Master Intensity 0 100 Auto running mode built in program Strobe effect 0 100 Auto running speed control from slow to fast 0 255 0 255 0 255 0 255 0 255 0 255 15 channel 0 255 16 channel 17 channel 18 channel 19 channel 20 channel 21 channel 22 channel 23 channel 24 channel 25 channel 26 channel 27 channel 28 channel Hanson ProSystems www hansonprosystems com User Manual Page 19 of 28 0 255 0 255 0 255 Red 0 100 Gree
11. 55 Blue 0 100 0 255 White 0 100 10 channel 0 255 Amber 0 100 11 channel 0 255 Sound Active Mode 12 channel 0 255 Remote Shut Off Remote fixture on off via DMX control Hanson ProSystems www hansonprosystems com User Manual Page 15 of 28 Hanson ProSystems www hansonprosystems com User Manual Page 16 of 28 HPS BPWDMXLED QUATTRO 45 Channel Basic Pixel Mapping Modes Channel Values Function 8 channel 0 255 10 channel 14 channel 0 255 The fourth group 15 channel 0 255 22 channel 23 channel Channel Red 0 100 Green 0 100 The first group Blue 0 100 White 0 100 Red 0 100 Green 0 100 The second group Fara 0 100 Amber 0 100 Red 0 100 Green 0 100 The third group Blue 0 100 White 0 100 Red 0 100 Green 0 100 Blue 0 100 Amber 0 100 Red 0 100 Green 0 100 The fifth group Blue 0 100 White 0 100 Red 0 100 Green 0 100 The sixth group Blue 0 100 Amber 0 100 24 channel 25 channel Hanson ProSystems www hansonprosystems com User Manual Page 17 of 28 26 channel 27 channel 28 channel 29 channel 30 channel 31 channel 32 channel 33 channel 34 channel 35 channel 36 channel 37 channel 38 channel 39 channel 40 channel 41 channel 42 channel 43 channel 44 channel 45 channel 0 255 0 255 0 255 0 255 0 2
12. INDICATOR Press enter indicates total hours of operation since manufactured indicator will start at 00 00 OPST OPERATION TIME Press enter indicates total hours of operation since manufactured Hanson ProSystems www hansonprosystems com User Manual Page 14 of 28 HPS BPWDMXLED QUATTRO Setting DMX Channel Modes The QUATTRO has 4 different DMX channel modes 6 12 45 and 51 To select the different DMX modes use the following steps See chart on page 16 17 18 for DMX Values and Functions Connect the fixture to a suitable power outlet or use internal battery 1 2 NARA A Turn the fixture on Unlock the fixture menu display by holding down the Up and Down buttons for 5 seconds the word Yes will appear on the menu display Then the fixture will be unlocked and ready to change settings For more information see page 13 Press lt UP gt repeatedly until CHAN shows on the display Press lt ENTER gt Press lt UP gt or lt Down gt to select the DMX channel mode your desire 6 12 45 and 51 Now your DMX channel mode is selected Press lt MENU gt to return to the previous menu Setting DMX Address When assigning a DMX address to the fixture always consider the number of DMX channels that the selected DMX mode uses If you choose a starting address that is too high you could restrict the access to some of the fixture channels The QUATTRO uses 6 12 45 and 51 DMX channels on the different DMX chan
13. Rev 1 12 JNANSON PROS YS TEM S amp S HANSONPROSYSTEMS COM HPS BPWDMXLED QUATTRO User Manual Battery Powered Wireless DMX LED Fixture A a To E i f 5 a Pi e A e ly A e k MR Patent Pending Hanson ProSystems 4960 NW 165 St Unit B 12 Miami Gardens FL 33014 www hansonprosystems com HPS BPWDMXLED QUATTRO Table of Contents A EA aA E EEE A E areuueT 4 A O o A A gee nee 4 FAUS QUO OVNIS Wise 4 AR A PP E ECO A 5 NV ANNI o iaa 5 A E A donate nts haraean yaa aan ponnaaeal onan 5 lo A eo AQ E 5 General Mormane ea a e A E a S 6 e e e OO AE E EN EAE ntti E ake 6 customer SUPPONE aran 6 Ac PPP eo POP EE o E Ea 6 ig A 1isahesnocesactenceadvasteaseasitasrebiktiaeetensaeaseusaaaseridlahiatistevessaishecsacised eiveanaatiniadrs 7 FISD AAA en E OO a r 7 FARTS DIMENSIONS aaa ado 8 e o E eii 9 SE AAA PP o iene dae stmt A EE E 10 A PON OOO A o o o ate acheter cine dao aeve A 10 CAL GING the Balto Carra 10 a An e ees 10 Battery Charge dica aaa iaa 10 Alp ATP AP 10 FUSE FRG AC CIS NN naaa 10 el O o o EEE E EO 11 DMA WIG SUD aaa Os 11 DNIA Wire IIA on 11 DMA ile al TMC ANON A o En E o ER Ei E E OE EENE EEE 12 MOON aia iia 12 PQA APC E ooo e E UB O OO e 12 6 ODT AON CAPA e A a i 13 Hanson ProSystems www hansonprosystems com User Manual Page 2 of 28 HPS BPWDMXLED QUATTRO Control PaliGl Ona NOM 13 PVA MAND AR o o OE E eiaa 13 Setting DMX Channel ModeS nia 15 SS TEI DM
14. X FG OSS omnia 15 DMX Valles and FOCUS oa 16 Sa AP o death E baer 21 Wired Master Slave Configuration cccccecccccccceccecceeeeeeeeeeeeeeeeeeeeceeeeaaaaeaaaaaaaaaeaeeeeeeeeeeeeseeeeaeeaaaas 21 Wireless Master Slave Configuration cccccccccceeseeeeseeeeeeeeeeeeeeeeeeceaaeaeaaeaaaaaaaaaaaaeseeeeeeeeeeeeeeeeeaaas 22 AA ee O O E eavectenalee 23 Examples of System Configurations cia aa 25 o o o A E E A A 26 HPS DMX WTR Fa ia 27 Ta NGF MOMAN Oasa aaa aa ando 27 cn E E OAIT L OAA E REES E A A AAEE EAE E E ETET 27 TrOUDIG SING OMIA Ra 28 PECO oaa aE E EE ea o da ane AAE ERE ANNEE a aeeiamne tans 28 Retums OS 0 AA e oe o E rii 29 SFO OIG CIAM nadia 29 9 Manufacturers Limited Warranty isis iaa 30 General IOMA Macaco 32 The information and specifications contained in this manual are subject to change without notice Hanson ProSystems assumes no responsibility or liability for any errors or omissions that may appear in this manual Hanson ProSystems reserves the right to update this existing manual or to create a new manual to correct any errors or omissions You can download the latest version of this manual from www hansonprosystems com Electronically published by Hanson ProSystems in the United States and printed in China To optimize the performance of this fixture please read these operating instructions carefully and familiarize yourself with the basic operations of the fixture These instructions contain important safet
15. apabilities Strobe 1 255 Color strobe 1 255 Master Slave Synchronization via wireless and wired Operation modes DMX Sound Active and Auto Modes Built in microphone for sound active mode LED chases Adjustable Speeds Dual bracket for floor stand and or hanging mount Dual eye bolts for safety cables LIGHTWEIGHT for easy transport 19 LBS COMPACT for low visibility VERSATILE LED wireless lighting fixture AC power auto ranging 100 240v 50 60HZ In Out Length 19 3 in 431 8 mm Width 3 5 in 76 2 mm Height 9 in 279 4 mm Weight 19 lbs 5 44 kg Hanson ProSystems www hansonprosystems com User Manual Page 9 of 28 HPS BPWDMXLED QUATTRO 5 Set Up AC Power Before plugging your fixture in be sure that the power source voltage in your area matches the required voltage for the fixture The QUATTRO works in 100 220V 50 60Hz Line voltages may vary from venue to venue therefore you should be sure that the fixture voltage matches the wall outlet voltage before attempting to operate it Always connect the fixture to a protected circuit circuit breaker or fuse Make sure the fixture has an appropriate electrical ground to avoid the risk of electrocution or fire Never connect the fixture to a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel serves only as a 0 to 100 switch Charging the Battery The battery included with the QUATTRO does not come completely charged It is recommend
16. ed that you charge the fixture for at least 6 hours before your initial use The QUATTRO comes with a replaceable lithium ion battery for cable free and wireless operation To charge the battery simply plug in the power con cable into the power con input at any time before during or after operation Switch the battery switch to the CHARGE position at this point the fixture will start the charging process Battery Life Display The battery life display located in the menu options of the LED Display shown as BTCC will display the remaining amount of internal battery life 0 100 See Menu Map on page 13 amp 14 to find BTTO Battery Charge Indicator The QUATTRO has a battery charge indicator on the front left portion of the fixture When charging the LED indicator will turn red Once the fixture is fully charged the LED indicator will turn green See fixture diagram on page 7 for the location of the Battery Charge Indicator Battery Maintenance The QUATTRO should be charged for at least 6 hours prior to initial operation for optimal battery usage To keep the battery in optimal operating condition store the fixture in a cool dry place and charge it at least once every 30 days when it has not been in use Avoid exposure to extreme temperatures If the fixture is exposed to extreme cold or hot temperatures this may cause the battery to fail or shorten the life of your battery Your battery has a run time of up to12 hours of battery
17. end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that fixture no matter where it is located in the DMX chain Hanson ProSystems www hansonprosystems com User Manual Page 11 of 28 Hanson ProSystems www hansonprosystems com User Manual Page 12 of 28 HPS BPWDMXLED QUATTRO 6 Operation Control Panel Operation To access the control panel functions use the four buttons located around the display Please refer to the fixture Diagram to see the button locations on the control panel Menu Buttons Menu Press to back out of the current menu option Up Press to scroll up the list of options or to find a higher value or speed Down Press to scroll down the list of options or to find a lower value or speed Enter Press to activate a menu option or a selected value 1 To unlock versions 1 0 and 1 1 on the display menu hold down the Up and Down buttons for 5 seconds the word Yes will appear on the menu display Then the fixture will be unlocked and ready to change settings After 60 seconds of no operation the menu display will automatically lock to protect display e To unlock versions 1 2 and higher on the display menu hold down the Menu and Enter buttons for 5 seconds the word Yes will appear on the menu display screen Then the fixture will be unlocked and ready to change settings After 1 minute and 20 seconds of no operati
18. figuration This fixture has multiple pre programs manual operations internal strobe sound active wired and wireless DMX built in Customer Support Hanson ProSystems customer service line provides help and answers for any questions you may have or problems you may encounter during your set up and or initial operation You may also visit our website at www hansonprosystems com if you have any comments or suggestions Customer Support hours are Monday through Saturday from 10 00am to 7 00pm EST Phone 305 623 2900 Toll Free 1 855 462 4HPS 477 Fax 305 626 8300 Email support hansonprosystems com Warranty Registration The QUATTRO includes a 3 year 1095 days limited warranty for the LEDs and internal components The battery carries a 1 year 865 days limited warranty The wireless antenna on the fixtures has no warranty Please fill out the enclosed warranty card to validate your purchase and warranty All returned service items whether under warranty or not must be freight pre paid and have a return authorization R A number If the fixture is under warranty you must provide a copy of your original invoice Please contact Hanson ProSystems customer support department for an R A number Hanson ProSystems www hansonprosystems com User Manual Page 6 of 28 HPS BPWDMXLED QUATTRO HPS BPWDMXLED QUATTRO 4 Introduction Diagram Fixture Dimensions Fixture Diagram 2 in TRANSCEIVER LED amp SELECTOR _ BUT TONS
19. ixture to the desired angle Only loosen or tighten the bracket knobs manually Using tools could damage the knobs The double bracket yoke on the ORIGINAL also serves as a floor support or allows for surface mounting When using the fixture on the floor tighten the bracket adjustment knobs firmly to keep bracket secure Make sure that the fixture and cables are away from doorways people and vehicles DMX Wire Setup Set the fixture in DMX mode to control with a DMX controller 1 Connect the fixture to a suitable power outlet or use internal battery 2 Turn the fixture on 3 Connect a DMX cable from the DMX output of the DMX controller to the DMX input on the fixture DMX Wire Linking 1 Make sure previous step on DMX wire setup is done already 2 From the DMX output of the first fixture run a DMX cable to the DMX input of the second fixture 3 Repeat step 2 for each fixture you wish to use FIXTURE 1 FIXTURE 2 FIXTURE 3 TO OTHER FIXTURES an l l mem Se it A 60 00 00 l DMX DMX DMX DMX DMX DMX l INPUT OUTPUT a et et es ee a DMX CONTROLLER ee To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the
20. life per charge and 6 hours of recharge time Fuse Replacement The QUATTRO has two different fuses one for the AC power 5A 250V and a second fuse for the battery 5A 250V Always replace a blown fuse with a fuse of the same type and rating The fixture does not ship with spare fuses 1 Disconnect the fixture from the power outlet before replacing the fuse and turn off the battery 2 Use a Phillips screwdriver to remove fuse holder 3 Remove the blown fuse from the holder and replace with a fuse of the exact same type and rating 4 Insert the fuse holder back in place and reconnect power Hanson ProSystems www hansonprosystems com User Manual Page 10 of 28 ower HPS BPWDMXLED QUATTRO INKING The fixture provides power linking via the power con outputs located in the back of the fixture Please see the diagram below for further explanation HPS BPWDMXLED QUATTRO DMX Signal Indicator When menu display screen is locked the red dot in LED display will blink indicating DMX signal If the red dot is not blinking the unit is indicating that there is no DMX signal Mounting Before mounting the fixture read and follow the safety recommendations indicated in the rigging section below The QUATTRO may be mounted in any position however make sure there is Li FIXTURE 1 FIXTURE 2 FIXTURE 3 TO OTHER adequate ventilation around the fixture to prevent overheating Ve A FIXTURES o a Je APRO a Py
21. n 0 100 Blue 0 100 White 0 100 Red 0 100 Green 0 100 Blue 0 100 The first group The second group Amber 0 100 Red 0 100 Green 0 100 The third group Blue 0 100 White 0 100 Red 0 100 Green 0 100 The fourth group Blue 0 100 Amber 0 100 Red 0 100 Green 0 100 oe Blue 0 100 White 0 100 Red 0 100 The sixth group Green 0 1 00 Blue 0 100 HPS BPWDMXLED QUATTRO 29 channel E S Amber 0 100 30 channel Red 0 100 31 channel Green 0 100 32 channel The seventh group Pie 0 100 33 channel White 0 100 34 channel Red 0 100 35 channel Green 0 100 36 channel The eight group Blue 0 100 37 channel Amber 0 100 Red 0 100 Green 0 100 Blue 0 100 White 0 100 Red 0 100 Green 0 100 38 channel 39 channel The ninth group 40 channel 41 channel 42 channel 43 channel The tenth group 44 channel 0 255 Blue 0 100 45 channel 0 255 Amber 0 100 46 channel 0 255 Red 0 100 47 channel Green 0 100 Blue 0 100 White 0 100 Sound Active Mode The eleventh group 48 channel 49 channel 50 channel 51 channel Remote Shut Off Remote fixture on off via DMX control Hanson ProSystems www hansonprosystems com User Manual Page 20 of 28 HPS BPWDMXLED QUATTRO Standalone Modes Set the
22. nel modes To select the starting address do the following steps 1 2 3 E Connect the fixture to a suitable power outlet or use internal battery Turn the fixture on Unlock the fixture menu display by holding down the Up and Down buttons for 5 seconds the word Yes will appear on the menu display Then the fixture will be unlocked and ready to change settings For more information see page 13 Press lt UP gt repeatedly until A001 shows on the display Press lt ENTER gt Press lt UP gt or lt Down gt to select the DMX address you desire Press lt ENTER gt and now your DMX address is assigned Press lt MENU gt to return to the previous menu Channel Values HPS BPWDMXLED QUATTRO DMX Values and Functions 6 Channel Basic Modes Channel 1 chamnel 2 channel 3 channel 4 chamnel 5 channel 6 channel Channel Values Function 0 255 Red 0 100 Green 0 100 Blue 0 100 0 255 White 0 100 0 255 Amber 0 100 Remote Shut Off Remote fixture on off via DMX control 12 Channel Advanced Modes 1 channel 2 channel 3 channel 4 channel 5 channel 6 channel 7 channel 8 channel 9 channel 0 255 Red Green Blue White Master Intensity 0 100 Red Green Blue Amber Master Intensity 0 100 Auto running mode built in program Strobe effect 0 100 0 255 Auto running speed control from slow to fast 0 255 Red 0 100 0 255 Green 0 100 0 2
23. nson ProSystems Service Department at 305 623 2900 to obtain a Return Authorization Number RA all returned service items whether under warranty or not must be pre paid by the sender Hanson ProSystems will at its own expense return the repaired product only in the United States and only if the product is under warranty lf the fixture is under warranty you must provide a copy of your original invoice No accessories should be shipped with the product If any accessories like cables are shipped with the product Hanson ProSystems shall have no liability for loss or damage of accessories B This warranty is void if the serial number has been altered or removed if the product is modified in any manner Do not attempt any repairs yourself doing so will void the Hanson ProSystems warranty If the warranty seal is broken or tampered with customer s warranty is void and any warranty claims If the product has been repaired or serviced by anyone other than Hanson ProSystems unless prior verbal consent and written authorization was given to buyer by Hanson ProSystems if the product is damaged because of abuse misuse wrong installation improper maintenance will void all warranties C This is not a service contract and this warranty does not include maintenance cleaning or periodic check up During the limited warranty Hanson ProSystems will replace LED s and internal components and will cover all service and repair labor expenses The wireles
24. on Never plug this fixture into a dimmer pack Power supply cords and DMX cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them Pay particular attention to the point they exit from the fixture This does not apply when in wireless operation Fuse standard is 5A 250V for AC power and 5A 250V for the Battery Grounded using yellow green line During long periods of non use disconnect the fixture from main power source Do not remove the cover under any conditions There are no consumer serviceable parts inside Never operate this fixture if the cover is removed Do not attempt to operate this fixture if it becomes damaged e Always be sure to mount this fixture in an area that will allow proper ventilation Allow about 3 7 62cm between this fixture and a wall e Always mount this fixture in a safe and stable manner e The fixture should be serviced by qualified service personnel when 1 The power supply cord or plug has been damaged 2 Liquid has been spilled into the fixture 3 The fixture has been exposed to rain or water 4 The fixture does not appear to operate normally or exhibits a marked change in performance e The fixture should be cleaned only as recommended by Hanson ProSystems See Cleaning on page 25 for more details e This product contains a rechargeable battery This battery contains hazardous chemicals that cannot be discarded with household waste Con
25. on the fixture will automatically lock to protect screen e For a faster approach to unlock fixture versions 1 2 and higher turn fixture OFF and turn ON again Then the fixture will be unlocked and ready to change settings After 1 minute and 20 seconds of no operation the fixture will automatically lock to protect screen 2 Press the Menu button and UP button or DOWN button until A001 is displayed this will be your starting point See chart below Menu Map ADDR A001 DMX ADDRESS DMX Address display 001 512 Press enter then Up Down to assign a DMX address enter to confirm 6 CH Press enter then Up Down to assign a DMX Channel 12 CH Press enter then Up Down to assign a DMX Channel 45CH Press enter then Up Down to assign a DMX Channel 51 CH Press enter then Up Down to assign a DMX Channel Standalone Modes RGBW or RGBA gradual pulse speed 00 99 Press enter then Up Down to alter the speed enter to confirm CHAN DMX CHANNEL MODE CG00 00 99 PULSE EFFECT 1 Standalone Modes RGBW or RGBA combination variety speed 00 99 Press enter then Up Down to alter the speed enter to confirm CJOO 00 99 COLOR STROBE Standalone Modes RGBW or RGBA pulsating change gradual change 00 99 Press enter then Up Down to alter the speed enter to confirm CPOO 00 99 PULSE EFFECT 2 Red manual operation 000 255 RO00 255 Press Up Down to alter the value press enter for next color option NANU MANUAL Green manual operation 0
26. one to all the units that will become receivers This process is unlimited 4 Once steps 1 2 and 3 are completed you will have one unit as your transmitter master with the LED solid yellow on and all other units as receiver slave and the LED will be completely off 5 Your final step is to link the transmitter unit to the receiver units e On your transmitter master unit press the red button lt DOWN gt Now the transmitter unit will send a signal to all the receivers units In this step you will see all the LED indicators on the units blinking fast e Once the transmitter unit finds the best frequency to transmit all the LED indicators on the receiving units will be solid yellow Note if you don t want to use any of the units as a transmitter and will be using a Black Box or other Wireless Solutions transmitters the process for the receiver units will be the same as step 3 4 5 Then on that Black Box you will push down the red button to link all the receiver units to the Black Box Hanson ProSystems www hansonprosystems com User Manual Page 22 of 28 HPS BPWDMXLED QUATTRO Battery Functions The fixture has the ability of being battery powered The switch for the battery on off and charge is set on the rear panel of the fixture It is showed as the following diagram and the functions are described below AC POWER BATTERY TRANSCEIVER There are three switches on the rear panel of the fixture The first is for AC powe
27. onfiguration This function will allow you to link together and operate without DMX cables or a DMX controller In wireless Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units programs Any unit can act as a Master or as a Slave 1 Connect a DMX 512 cable from the output of a DMX 512 console or DMX 512 software to the desired input of a Quattro fixture to become your transmitter master Make sure your controller source is on and is sending DMX protocol signals to your Quattro unit 2 On the same unit that will be your transmitter master next to the antenna you will find a LED indicator and a red push button In order for this unit to become a transmitter the LED indicator must be yellow If the LED is blinking or pulsing you are not in the right mode To set the unit as a transmitter e Hold down the red Tx Rx button and at the same time shut off the transceiver on off switch on the back panel of the unit while still holding down the red push button turn on the transceiver on off switch and release the red push button after a second If the LED indicator is now solid yellow this unit is now a transmitter Note if the LED indicator is not solid and blinking or pulsing repeat the steps above until the LED is solid yellow 3 On the units that will become receivers the LED indicator must be completely off Follow the same steps above to achieve this Note this same process must be d
28. or concealed damage file a claim with Hanson ProSystems within seven 7 days of receiving the merchandise PLEASE recycle the shipping carton whenever possible Fixture Quick Overview e AC Power Yes e Auto Programs Yes e Auto Ranging Power Supply Yes e Battery Powered Yes o DMX Yes Master Slave Yes Replaceable Battery Yes Replaceable Fuses Yes e Sound Activated Yes e Wireless DMX Yes e Outdoor Use No Use On A Dimmer No User Serviceable No Hanson ProSystems www hansonprosystems com User Manual Page 4 of 28 HPS BPWDMXLED QUATTRO 2 Safety Precautions e This fixture is intended for indoor use only use of this fixture outdoors voids warranty e To reduce the risk of electrical shock or fire do not expose or spill this fixture to any liquids or moisture Do not spill water or any other liquids onto your fixture The fixture should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat The ambient temperature must always be under 35 C Be sure that the local power outlet matches the required voltage for your fixture Do not attempt to operate the fixture if the power cord has been frayed or broken Do not attempt to remove or break off the ground from the electrical cord This ground is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connecti
29. out prior notice Hanson ProSystems www hansonprosystems com User Manual Page 28 of 28 HPS BPWDMXLED QUATTRO Returns Procedure You must send the fixture and all its accessories back in the original box original packaging and with pre paid shipping Hanson ProSystems will not issue call tags You MUST call Hanson ProSystems and request a Return Merchandise Authorization Number RMA before shipping the fixture Be prepared to provide the model number serial number and a brief description return reason You must clearly label the package with the RMA number that was provided to you by our customer service representative Hanson ProSystems will NOT accept any fixture returned without an RMA number DO NOT write the RMA number directly on the original box Instead write it on a properly affixed label Once you receive the RMA number please include the following information on a piece of paper inside of the box Your name Address Phone number RMA number Brief description of the problem MARINOS Be sure to pack the fixture properly Any shipping damage resulting from inadequate packaging will be the customer s responsibility As a suggestion proper packing or double boxing is always a safe method to use Hanson ProSystems reserves the right to use its own discretion to repair or replace returned fixture s Shipping Claims The carrier is responsible for any damage incurred during shipping to this fixture or any part
30. r the second is for the battery operations and the third is for the transceiver AC Power When you use the fixture with the AC power not the battery switch the AC power to ON and switch the battery to battery OFF Battery Power When you use the fixture with the battery instead of AC power switch AC power to OFF and then switch the battery to battery ON AC Power and Charge When charging the fixture switch to charge At the same time if the switch for AC power is ON the fixture will be at work during the process of charge but will consume some power from the charge if the switch for AC power is OFF the fixture will be off and not working but charging Transceiver Power When you use the fixture in DMX wireless mode turn the transceiver switch to ON When using wired DMX the transceiver must be in the OFF position If not the signals could interfere with each other Hanson ProSystems www hansonprosystems com User Manual Page 23 of 28 HPS BPWDMXLED QUATTRO When you use the fixture in wireless DMX mode you must use a compatible wireless transceiver like the HPS DMX WTR To enable the Wireless DMX do the following steps a a Connect the fixture to a suitable power outlet or use the internal battery Turn the fixture ON On the fixture turn receiver switch to the ON position Locate the Receiver Frequency Selector button and the LED indicator on the right side of the fixture Here you must assign the desired ID
31. red correctly pin 3 is hot on some other DMX devices pin 2 may be hot Also check that all cables are connected to the appropriate connectors Fixture does not respond to wireless DMX Make sure the controller is powered on and the DMX cable is connected to the transceiver Check that the transceiver and the fixture have the same ID code assigned to each other To reset connection turn transceiver OFF wait 5 seconds and turn transceiver ON Fixture does not respond to sound Low frequencies bass should cause the fixture to react to sound Tapping on the microphone quiet or high pitched sounds may not activate the fixture Specifications Model HPS BPWDMXLED QUATTRO Working Position Any safe working position Power Supply Switching power supply Voltage AC 100 240V 50 60Hz Power Consumption 35W Color of shell White or Black RGBWA color mixing Optional RGBA or RGBW 11 4 in1 Watt LED 6 RGBW 5 RGBA 25 degree lenses Optional 15 45 60 lenses Weight 12 lbs 5 44kg Fuse 5A 250V fixture Fuse 5A 250V battery DMX 6 12 45 or 51 channels Sound active yes Battery powered and wireless DMX control The battery can last for more than 12 hours on auto running mode and approximately 12 hours in the event that all LED lights are on Wireless control 150m 492ft with barriers 400 500m 1 31 2ft without barriers e Warranty 3 Year limited warranty Note All information is subject to change with
32. s antenna on the fixtures carries no warranty The sole responsibility of Hanson ProSystems under this warranty shall be limited to the repair of the product or replacement thereof including parts at the discretion of Hanson ProSystems D Hanson ProSystems reserves the right to make changes in design and or improvements upon is products without any obligation to include these changes in any products thereafter manufactured Hanson ProSystems www hansonprosystems com User Manual Page 30 of 28 HPS BPWDMXLED QUATTRO HPS BPWDMXLED QUATTRO No warranty whether expressed or implied is given or made with respect to any accessory supplied with General Information products described above Except to the extent prohibited by applicable law all implied warranties made Hanson ProSystems by Hanson ProSystems in connection with this product including warranties of merchantability or fitness 4960 NW 165 St Unit B 12 Miami Gardens FL 33014 shall apply to this product after said period has expired The consumer s and or dealers shall be such Phone 305 623 2900 repair or replacement as is expressed above and under no circumstances shall Hanson ProSystems be Toll Free 1 855 462 4HPS 477 liable for any loss or damage direct or consequential arising out of the use of or inability to use this Fax 305 626 8300 product This warranty is the only written warranty applicable to Hanson ProSystems products General Information email info hansonprosystem
33. s com MANUFACTURER S LI MI TED WARRANTY PERI ODS Sales email sales hansonprosystems com e All Hanson ProSystems Fixtures 3 year 1095 days limited warranty Support email support hansonprosystems com excludes wireless antennas Service and repair email service hansonprosystems com e Hanson ProSystems Lithium Ion Battery 1 year 365 days limited warranty www hansonprosystems com e All Hanson ProSystems Co2 jets 1 year 365 days limited warranty e All Hanson ProSystems Laser products 1 year 365 days limited warranty Model A Date Purchased E a C ja F LEA Serial number s HANSON PROS Y S5 TEM S amp S HANSONPROSYSTEMS COM Register your products online at www hansonprosystems com warranty Hanson ProSystems www hansonprosystems com User Manual Page 31 of 28 Hanson ProSystems www hansonprosystems com User Manual Page 32 of 28
34. tact your local waste management service for recycling information when disposing of the battery Warning To prevent or reduce the risk of electrical shock or fire do not expose this fixture to rain liquids or moisture Beware the housing may become extremely hot avoid touching the fixture with bare hands while fixture is in use Caution Avoid looking directly into the light source Use sensible precaution as this may cause eye damage 3 Handling Precautions There are no user serviceable parts inside of this fixture Do not attempt to make any repairs yourself doing so will void the Hanson ProSystems warranty If the warranty seal is broken or tampered with customer s warranty is also void along with any warranty claims In the unlikely event that your fixture requires service please contact Hanson ProSystems during customer support hours Hanson ProSystems is NOT liable for any damages caused by the non observance of this manual or any unauthorized modification to this fixture Hanson ProSystems www hansonprosystems com User Manual Page 5 of 28 HPS BPWDMXLED QUATTRO General Information Introduction The QUATTRO is a battery powered and wireless DMX LED fixture It contains 6 12 45 and 51 DMX channel modes This fixture is designed to be a versatile compact and lightweight for up lighting stage wash LED effects and full linear pixel mapping capabilities The QUATTRO can operate as a standalone fixture or in a master slave con
35. y information regarding the use and maintenance of this fixture Please keep this manual with the fixture for future reference If this fixture is sold to another user be sure that they also receive this manual Hanson ProSystems www hansonprosystems com User Manual Page 3 of 28 HPS BPWDMXLED QUATTRO 1 Contents HPS BPWDMXLED QUATTRO 3 Ft Power con inlet to Power con outlet cable 3 Ft Power con to AC plug cable User Manual Warranty Card oF A Thank you for purchasing the HPS BPWDMXLED QUATTRO Every QUATTRO fixture has been thoroughly tested and shipped in perfect operating condition Carefully inspect the shipping box for any damages that may have occurred during shipping If the box appears damaged check your fixture thoroughly for any damage and or missing accessories Please contact Hanson ProSystems or your authorized dealer for further instructions if the product you have received is damaged or missing parts DO NOT return the fixture to your dealer without contacting them first Claims If the box or any of its contents appear damaged from Shipping or mishandling notify the shipping carrier immediately DO NOT contact Hanson ProSystems Failure to contact the shipping carrier in a timely manner may invalidate your claim In addition keep the cardboard box and all the packaging materials for inspection For other issues NOT involving shipping damage such as missing components or parts damage not related to shipping

Hanson QUATTRO MANUAL V1 0

Contents

Download Pdf Manuals

Related Search

Related Contents