e4ride electric skateboard - user manual
Contents
1. Do not recharge in an area that will allow the e ride Skateboard or the charging unit to become wet Recharge only in an area that is well ventilated 4 Keep children away from the efride Skateboard while it is being recharged 5 Stop use of the product or the charging unit if any wire becomes worn broken or damaged in any Way 6 Do not modify the electrical controls or wiring Use only motors batteries and charging units supplied or approved for the efride Skateboard 7 Do not use the efride Skateboard battery to power or recharge any other equipment 8 Do not block the air vents on the charging unit If blocked the charging unit may overheat and create a fire hazard TROUBLESHOUTING repute Description amp Reason How To Fix Troubles 1 Skateboard hand controller is not powered on Turn on the skateboard You should hear a beep 2 The rider is not standing on the board Step on the skateboard 3 Trigger of the controller is not in the right position Pull gently the trigger backwards 4 The indicator is not light that means insufficient Skateboard will battery capacity Recharge the battery not start up f f s 5 The dictator flickers in red and green means Re start when motor controller is overheat overload protection of motor controller cooled 6 If no beep when turn on controller means battery wrong insertion or run out of battery ESAE PAREN Or change Hatiery 7 Rider s hand does not touch directly the metal2. Palm touch the metal film directly or film of handle controller or glove is too tick take off the glove Skateboard stops 1 Overheat overload protection of motor Cool the motor automatically after running for 2 Low voltage protection of the controller Change or recharge the battery some time 1 Rider s hand does not touch directly the metal film of handle of controller or glove is too tick which results in bad transmitting Palm touch the metal film directly or take off glove 2 The metal film of the handle controller is damaged or came off which results in bad signal Repair the damaged metal film transmitting 3 Rider s location on the skateboard is not s Discontinuous completely correct Adjust location outage during z running process 4 The metal film of the bottom of the skateboard is Repair the metal film damaged 5 Controller and receiver are soaked in water or Drain dry became moist 6 Insufficient battery indicator became red Recharge the batteries Open the gun and clean it using a special spray you can buy from electronic shop 7 The potentiometer on the trigger has been contaminated which results in bad contact 1 Inserted incorrectly or battery pack connects become open circuit the charger indicator shows Reset connect the circuit again green indicator does not show any light It is unable to alternately glimmers it means coming to full charge 4 Red light flashes in succession because a
3. charger does not work smoothly Change charger or change the battery b too charge the battery low voltage of battery group group Strong vibration Adjust the belt and fasten all screws and high noise ny Pelt bocama NGXIDIE and nuts adjust back nut during running or braking 2 Bearing is damaged Change bearing
4. motor batteries and controls can be damaged if exposed to water Do not allow the efride Skateboard to be used in the rain nor to be driven though puddles of water 6 The product is designed to be used by one person at a time Product abuse will not be repaired without charge even during the warranty period So do not carry additional people or any cargo And do not put additional loads on the efride Skateboard by pulling or towing anything 7 Your insurance policy may not provide coverage for accidents involving this product Contact your insurance agent for more information 8 Do not do stunts or jumps like you would do with an ordinary skateboard You might seriously damage the efride Skateboard and injure yourself or others in the process Be considerate ride safely and with style Mechanical Safety Tips 1 Check all nuts bolts and mounted components to ensure the efride Skateboard is properly assembled 2 Stop using the product immediately if any part becomes loose Correct the looseness prior to resuming the ride 3 Maintain proper tightness on the wheel nuts Too tight a pressure on the axle increases friction reduces speed and thus operation time as well as wearing the wheel material quicker Electrical Safety Tips 1 Completely charge the battery before riding the e ride Skateboard for the first time 2 Turn off the efride Skateboard and the remote controller when not in use 3 Use caution when recharging the batteries
5. to operate on a unique channel blocking any external radio interference and only allowing the user to take control Last but not least for sensible progression there s a nifty operating power selector that lets you choose one of three skill levels This feature is accessed using one of three positions of a switch inside the handheld remote Using the efride beginner setting for low speed learning the maximum travel range is also achievable Go for the intermediate setting when you have more experience with the e ride functions And for maximum power and speed use the expert setting User Instructions 1 Charge the battery before use The charger plugs into an ordinary wall outlet and into the controller which is mounted under the deck in a small aluminum box The batteries are fully charged when the light on the charger turns from red to green 2 Start by using the beginner mode even if you are an expert rider Slide the lid off the bottom of the pistol style handheld remote and carefully pull out the 9 volt battery Always shut the remote off at the top of the pistol to change modes Then make sure the small sliding switch inside is pushed right to the end towards the front of the pistol 3 Do not forget your padding and helmet 4 Now turn on the skateboard power by pushing the red button on the controller opposite side to the charging port until you see a green light And stand anywhere on the deck 5 Flip the switch on th
6. Follow the inspection procedure Then pull off the wheel after carefully prying the chrome hubcap off and undoing the axel nut Place the new belt around the motor sprocket and the axel Slide the wheel back on rotating for the last bit to bring the edge of the belt around the drive wheel sprocket and then all the way on slipping laterally bit by bit Replace the nut and the hubcap A little Tack It on the hubcap mounts will help keep them in place Bearing replacement The wheel bearings are press fit and can be replaced using hand tools after removing the wheels Follow the drive belt replacement procedure to remove the drive wheel User tips 1 Go for smooth operation Avoiding excessive acceleration will not only look good and reduce the risk of personal injury conservative riding will also prolong battery life with a gradual battery discharge rather than a degrading rapid discharge 2 Lean back before braking and maintain drive wheel traction Excessive unbalanced braking will allow the wheel to skid and quickly wear out The controller has very efficient and powerful EABS electronic brake Braking smoothly will protect your driving wheel and driving belt from extreme wearing 3 Use a rechargeable 9 Volt battery for the handheld remote and recharge regularly If during operation beeping is heard your battery is in immediate need of charging This is a warning for your protection because neither the motor nor the braking will be functio
7. e ride electric skateboard user manual Introduction The e fride skateboard is controlled by a wireless handheld remote that allows instant throttle response with smooth acceleration and deceleration A number of safety features are incorporated into the design for ease of operation and reliability The most important is the integrated EABS electric braking that actually charges the battery when slowing down or stopping When the handheld remote controller is switched on a beep is heard to indicate that all is well If you hear this beep repeatedly during operation this indicates that the 9V battery inside the handheld remote is low on power and has typically been used for more than one hundred hours This is an important safety feature as in a few minutes the hand held remote will no longer be able to control the skateboard motor This inability includes the electric braking function and the skateboard will then only coast like a regular one without power Therefore using two rechargeable NiMH 9V batteries and swapping them to the charger routinely is highly recommended And the more often you charge them the greater their overall longevity This way you save money and throw less away Another safety feature prevents the skateboard from being used unless a person is on the deck A proximity sensor feels your immediate proximity allowing control or removing power should the rider step away from the deck The efride is also designed
8. e top of the handheld remote and listen for a short beep The system is then ready to go If you don t hear a beep or you hear a repeated beep replace the 9V battery with a fully charged rechargeable NiMH battery 6 Lean forward before using the remote throttle Gently and gradually pull the pistol trigger until the skateboard starts You will hear a slight buzzing low frequency noise coming from the skateboard This is normal and can warn people that a powered skateboard is in operation near them 7 Make special note that the electric brake is activated as you release the spring loaded trigger So again do this gently for a gradual acceleration and deceleration This way you will maintain good control as well as preserving your electric drive components like the belt drive wheel and batteries reducing wear and the likelihood of any premature failure 8 Steer the efride as you would a regular skateboard 9 For your safety a e ride motor will stop and brake automatically if you drop the handheld remote or step off the deck while riding 10 To prevent battery discharge both components shut down automatically after several minutes of inactivity After a few minutes of not being used a short beep is heard from the handheld remote as it goes off Then after a total of about ten minutes a two tone beep indicates that the skateboard has shut off Maintenance Electric skateboards are extremely reliable as there are very few moving
9. nal in a few moments 4 Set the handheld remote for beginners The e ride XT controller allows you to preset its maximum speed in three ranges 0 8 km h 0 15 km h and 0 30 km h To change the speed range shut off the controller and open the lid on the battery box on the underside of the controller Slide out the battery and locate the small three position switch as shown on the picture Slide the switch all the way upfront for the lowest speed slide it backwards one step for the medium speed and one more time backwards for the fastest speed range Then turn on the remote controller again 5 Use direct hand contact with the chrome ring on the handheld remote An unusual grasp or gloves can interfere with your ability and the system may not work properly General Safety Tips 1 The e ride Skateboard is intended for use by persons aged 14 or above 2 Operators must comply with all local laws and regulations Check with your local police or transport department to determine local requirements Pay special attention to local helmet and safety gear laws 3 Always wear your ANSI or Snell approved helmet Elbow and kneepads are a good idea for protection from injuries including laceration in the event of a fall 4 Do not operate the efride Skateboard at night A efride Skateboard is not equipped to be operated in the dark or low light conditions You will not be easily visible to pedestrians or drivers without sufficient daylight 5 The electric
10. parts So other than charging your battery at every possible opportunity without delay to increase longevity the drive belt tension is of paramount importance Too tight is as bad as too loose Belts wheels bearings and batteries are subject to wear and tear Replace them before they cannot be used normally Drive belt inspection A sawing noise on startup or stopping may be caused by a slipping drive belt If you suspect that the drive belt is not properly adjusted remove the lid of the plastic belt protection box by unscrewing the two Phillips screws by the left back wheel Inspect the belt by rotating the wheel A worn or stretched belt should be replaced to preserve the drive wheel sprocket Now Press the belt with your thumb at mid span to assess the slack Normally the belt should sink about 5mm Drive belt adjustment If it feels loose or you have heard or felt any belt slippage tighten the belt by loosening the two Allan bolts washer bolt nuts and the kingpin nut Push the motor unit forward and retighten the nuts and bolts If the belt is too tight there will be unnecessary stress not only on the belt but also the bearings This will rapidly increase the likelihood of belt breakage and also reduce the life of the motor and wheel bearings Loosen a tight belt by moving the motor unit back To achieve proper tension you may have to take out the belt adjust and put it back in See the belt replacement procedure Drive belt replacement
Download Pdf Manuals
Related Search