IPC-8462 Version: A0
Contents
1. surge and security conform to the national and international standards GB4943 GB9254 GB T17618 and GB17625 1 and conform to China Compulsory Certification CCC Ventilation and Heat Dispersion IPC 8462 all in one workstation has two 92x 20 air intake high speed double ball bearing temperature controlled low noise fans and two 60x 25 air outlet high speed double ball bearing temperature controlled low noise fans there are enough blowholes on the backside of the chassis after the workstation is started normally the strong wind will bring the heat out via the blowholes which can provide good performance of heat dispersion IPC 8462 1 Chapter 1 Product Description Besides there are double ball bearing high speed drawing fan which can draw the heat inside the power supply and chassis out to gain good heat dispersion effect Environmental Requirements Climate adaptability compliant with 4 8 1 Class2 GB T9813 O Mechanical adaptability including vibration adaptability shock adaptability and hit adaptability compliant with 4 8 2 Class2 GB T9813 EMC e Limits of radio disturbance is compliant with GB9254 1998 class A Immunity to disturbance is compliant with the limits of GB T 17618 1998 Reliability e MTBF gt 5000h e MTTR lt 0 5h Safety e GB4943 Compliant Requirements of Transportation and Storage o Transportation Well packaged products suit for transportation by truck ship and plane During transport2. IPC 8462 19 4U All in one Workstation with Pull out Keyboard Version AO The List of Items Your IPC 8462 should include the items listed below If there s any damage or loss please contact your distributor M One IPC 8462 workstation M One User s Guide M One box of accessories Note Some accessories along with the IPC 8462 may not be listed above Please refer to actual packing list or customer s requirements Announcement The information in this manual represents no promise or guarantee by EVOC EVOC reserves the right to make changes to the manual without prior notice to customer EVOC will not be held liable for any direct indirect intended or unintended losses and or hidden dangers due to installation or improper operation EVOC is a registered trademark of EVOC Intelligent Technology Co Ltd All trademarks registered trademarks and trade names used in this User s Guide are the property of their respective owners The information in this user guide is protected by copyright No part of this manual may be reproduced in any form or by any means electronic or mechanical including photocopying recording or by any information storage and retrieval system without permission in writing from EVOC Safety Instructions 1 Please read the User Manual carefully before using your IPC 8462 Before inserting removing or re configuring motherboard or expansion card first disconnect the computer and p
3. allation LCD Outline Yo o C COOCEECE amp L Oy IPC 8462 Chapter 2 Installation Clamp Assembly Diagram Clamp SSE Clamp Mat IPC 8462 Chapter 2 Installation E gt gt Keyboard Outline IPC 8462 T9 Chapter 3 Installation of Drivers Chapter 3 Installation of Drivers Regarding the installation of the driver program of the product please refer to the manual of associated motherboard For detailed information please call 0755 82970999 or visit our website WWW VOC com IPC 8462 10
4. ation products should not be put in open cabin or carriage When transshipping en route products should not be stored in the open without protection from the atmospheric conditions Products 2 IPC 8462 Chapter 1 Product Description should not be transported together with inflammable explosive and corrosive substances and are not allowed to be exposed to rain snow and liquid substances and mechanical force o Storage Products should be stored in package box when it is not used And warehouse temperature should be 0 C 40 C and relative humidity is 20 85 In the warehouse there should not be harmful gas inflammable explosive products and corrosive chemical products and strong mechanical vibration shock and strong magnetic field affection The package box should be over ground at least 10cm height and 50cm away from wall thermal source and vent Troubleshooting Please refer to Common Trouble Analysis and Treatment of Industrial Control Computer for a detailed description of the troubleshooting IPC 8462 33 Chapter 2 Installation Chapter 2 Installation Dimensions 3 N a E Milla e 1 E 1 1 Unit mm IPC 8462 4 Chapter 2 Installation Sectional View A A 452 7 Unit mm Outline IPC 8462 Chapter 2 Installation Back View Exploded View IPC 8462 Chapter 2 Inst
5. eripherals from their power sources Before removing boards or computer first turn off all power resources and disconnect the power cord from power source For whole set when inserting or removing boards first disconnect the computer and peripherals from their power sources Before you connect or unplug any signal cable make sure all power cords are unplugged in advance To avoid power on off computer frequently wait at least 30 seconds after turning off the computer before re turning on the computer Static electricity can harm system boards Perform service at an ESD workstation and follow proper ESD procedure to reduce the risk of damage to components If there s no ESD workstation You can take the following steps to prevent damage from electrostatic discharge ESD a Wear a grounded wrist strap against your skin to eliminate static on your body b g Always touch the metal chassis or frame before you touch any components in the chassis Keep part of your body in contact with the metal chassis to dissipate the static charge while handling components Avoid all unnecessary movement Handle components and boards with care Don t touch the components or contacts on a board Hold a board by its edges or by its metal mounting bracket Place the components on a grounded static free surface Use a conductive foam pad if available but not the component wrapper Use a conductive foam pad if ava
6. he workstation is configured with 6 5 TFT LCD inside 14 slot embedded industrial grade backplane the driver bracket contains two 5 25 CD ROM bays one 3 5 FDD bay and one 3 5 HDD bay PS 2 power supply it has pull out keyboard configured at the bottom and two front side USB ports F1 F8 programmable function keys brightness and contrast of LCD adjustable standby power saving mode The chassis is constructed of high quality heavy duty steel featuring reasonable structure and stylish appearance It can be rackmounted in 19 industrial cabinet Integrated IPC system low cost and space saving all of these features provide a good solution for KVM user s low cost IPC server IPC 8462 is a high performance low cost 4U 19 embedded all in one workstation and can be widely applied to many fields such as electric power electric network transportation industrial automation manufacturing climate monitor etc Ordering Information Model Description IPC 8462 19 4U All in one Workstation with Pull out Specifications e Dimensions 19 rackmounted 4U height 483mm W x 501mm D x 177mm H IPC 8462 le Chapter 1 Product Description Operating Temperature 0 C 50 C Storage Temperature 40 C 60 C O Relative Humidity 5 90 40 C non condensing Configuration O Chassis IPC 8462 19 4U rackmount chassis e Backplane 14 slot industrial grade backplane Power Supply 250W industrial ATX p
7. ilable but not the component wrapper Do not let the components slide on the operating platform Use cross head screwdriver to operate A magnetic screwdriver is recommended magnet to collect screws Do not leave any tools or screws inside the chassis Do not leave any tools or screws inside the chassis 10 Assure abundant cooling and streamline ventilation Content Chapter 1 Product Description nono 1 OVEIVIEW ressentent 1 Ordering Information es 1 Specifications rer dr in Mr ni Mere nee Lu 1 C OTEL OUT ALLO sir el eas RE Pot ina a 2 ED ad 2 Keyboard mouse s 2 BACK PLAC cantada 1 Power SUPDI ew RA wR leeds 1 Ventilation and Heat Dispersion 1 Environmental Requirements i 2 EMO ds loe MASERA 2 Re lia Di lity cscs cast heres O E A 2 O 2 Requirements of Transportation and Storage 2 Troubleshootin lio o dia 3 Chapter 2 stallati n 3 lapo la dd dd 4 DIMENSIONS sise 4 OO 5 Exploded View x 5cestro oe ln ie 6 LCD Outline ia aia 7 Clamp Assembly Diagram ss 8 Keyboard Outline ss 9 Chapter 3 Installation of Drivers conan cnnonononns 10 Chapter 1 Product Description Chapter 1 Product Description Overview IPC 8462 is a 4U 19 embedded all in one workstation with LCD chassis and keyboard all in one T
8. ower supply e LCD 6 5 TFT LCD VGA port Keyboard mouse pull out keyboard with mouse LCD IPC 8462 4U 19 all in one workstation adopts colorful 6 5 TFT LCD Its display port is independent module of VGA port resolution 640x 480 display controlling integrates adjust of brightness contrast etc standby power saving mode and can be independently removed without disassembling the whole set Keyboard mouse IPC 8462 4U 19 all in one workstation adopts pull out keyboard with mouse The pull out slide is installed at the bottom of the chassis Common keyboard and mouse configured F1 F8 programmable function keys 2 IPC 8462 Chapter 1 Product Description Backplane IPC 8462 all in one workstation is fully compatible with 14 slot industrial grade backplane with stable performance and strong expansion Power Supply IPC 8462 all in one workstation adopts 250W industrial ATX power supply with the dimension of standard PS 2 150 x 140 x 86mm with double ball bearing temperature controlled low noise fan PFC function environmental protection effective and power saving over current over voltage overloading and short protection which can be used in bad environment O Input voltage 175 264VAC O Input frequency 47 63Hz The power supply is capable of protecting against overloading and over voltage and features low leakage current and stable performance The performances of conduction radiation harmonics current
Download Pdf Manuals
Related Search