Use & Care Guide
Contents
1. JAI lt Q T a D D O 9 o o S a S lt Y Extended high heat drying cycle intended to help sanitize items such as sheets and towels This cycle is not recommended for all fabrics For best results this cycle should be run to completion to ensure sanitization and do not interrupt cycle 13 Using Your Dryer Basic Operation 4 WARNING Explosion Hazard Keep flammable materials and vapors such as gasoline away from dryer Do not dry anything that has ever had anything flammable on it even after washing Failure to follow these instructions can result in death explosion or fire WARNING To reduce the risk of fire electric shock or injury to persons read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance 1 Clean the lint screen Clean the lint screen before each load Pull the lint screen straight up and push tab down on front to open lint screen Roll lint off the screen with your fingers Do not rinse or wash screen to remove lint Wet lint is hard to remove Close lint screen and push the lint screen firmly back into place For additional cleaning information see Dryer Care 14 4 WARNING Fire Hazard No washer can completely remove oil Do not dry anything that has ever had any type of oil on it including cooking oils Items containing foam rubber or plastic must be dried on a clothesline or by using an Air Cyc2. Q 12 but not optimal What to Dry Cycle Selection Towels Casuals Regular Automatic Sensor Cycle stops when dryness level is reached Steam Timed Refresh Dry Hot High Heat Used to kill 99 9 of 3 common bacteria Set amount of dry time Dryer runs for the amount of time selected Lower Heat Automatic Sensor Cycle stops when dryness level is reached Steam Cycle to remove wrinkles and odors How do you want to dry How to Dry Cycle Selection Steam Timed Refresh Dry Regular Hot High Heat Lower Heat Steam Cycle to Set amount remove wrinkles of dry time For best fabric care choose the cycle that best fits the load being dried R Recommended Cycle a Alternate Cycle Blank Cycle is available but not optimal s ee ta Cae Cree and odors Dryer runs for stops when 3 o a mon stops when the amount of dryness level CTO na dryness level time selected is reached is reached What do you What to Dry want to dry Cycle Selection Blankets Coats amp Jackets Comforters Fabric Rugs Fiber Fill Pillows not Bulky Sheets Heavy Drapes Pet Bedding Sleeping Bags Stuffed Animals Feather Pillows Plastic Shower Curtains Rubber and Rubber Air Only backed rugs and mats
3. n cessaire a l tablissement d une communication satisfaisante Le pr sent metteur radio IC 10248A XPWG3 a t approuv par Industrie Canada pour fonctionner avec les types d antenne num r s ci dessous et ayant un gain admissible maximal et l imp dance requise pour chaque type d antenne Les types d antenne non inclus dans cette liste ou dont le gain est sup rieur au gain maximal indiqu sont strictement interdits pour l exploitation de l metteur Type Gain admissible L imp dance d antenne maximal d antenne dBi requise OHM A fentes 1 76 50 Pour satisfaire aux exigences de la FCC et IC d exposition aux radiofr quences une distance de s paration de 20 cm ou plus doit tre maintenue entre cet appareil et des personnes lors de fonctionnement du dispositif Pour assurer la conformit des op rations au plus pr s que cette distance n est pas recommand e L antenne utilis e pour ce transmetteur ne doit pas tre co localis s en conjonction avec toute autre antenne ou transmetteur OEM Responsibilities to comply with FCC and Industry Canada Regulations The XPWG3 Module has been certified for integration into products only by OEM integrators under the following conditions 1 The antenna s must be installed such that a minimum separation distance of 20 cm is maintained between the radiator antenna and all persons at all times 2 The transmitter module must not be co located or o
4. O l HOME WIRELESS ROUTER Press the WPS button on the router An indicator light will begin blinking HELPFUL TIP The WPS function on your router is active for 2 minutes Complete the next step within that timeframe or you will need to reinitiate WPS 10 2 Dryer setup time sensitive step WHATTO DRY e Mixed Casuals Towels Delicates Bulky Sheets Wrinkle Shield ALAA a On e Static Reduc Connect Download amp Go End Beep Damp Beep Connect Download amp Go End Beep Damp Beep Finishing Touch Touch the POWER button A to turn on the dryer then touch the CONNECT button B The Wi Fi status indicator C on the dryer control panel will blink slowly while your dryer and router attempt to connect The Time Status display D will show a sensing animation This can take up to 2 minutes If the connection is successful the Wi Fi status indicator will come on and remain lit If Your Dryer Doesn t Connect If your dryer and router fail to connect after 2 minutes the Wi Fi status indicator C will blink rapidly for 2 seconds and then turn off Refer to the Troubleshooting Connectivity section of this Use amp Care Guide check any connection instructions for your specific router and refer to alternate instructions at www whirlpool com connect Connectivity Setup cont NOTE If this is your first Smart Appliance you will need to download the Whirlpool app and
5. OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE The following statements refer to those portions of the software copyrighted by Marvell International Ltd Copyright c Marvell International Ltd All rights reserved DISCLAIMER THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE 25 ATTACH YOUR RECEIPT HERE PROOF OF PURCHASE IS REQUIRED TO OBTAIN WARRANTY SERVICE WH R LPOO Le Please have the following information available when you call the Customer eXperience Center CO N N ECTE D LAU N D RY Name address and teleph
6. Pull the lint screen straight up Press tab down and open lint screen Roll lint off the screen with your fingers Do not rinse or wash screen to remove lint Wet lint is hard to remove 2 Close the lint screen and push firmly back into place IMPORTANT E Do not run the dryer with the lint screen loose damaged blocked or missing Doing so can cause overheating and damage to both the dryer and fabrics If lint falls off the screen into the dryer during removal check the exhaust hood and remove the lint See Venting Requirements in the Installation Instructions Clean space where lint screen is located as needed Using a vacuum gently remove any lint that has accumulated outside of the lint screen As needed cleaning Laundry detergent and fabric softener residue can build up on the lint screen This buildup can cause longer drying times for your clothes or cause the dryer to stop before your load is completely dry The screen is probably clogged if lint falls off while the screen is in the dryer Clean the lint screen with a nylon brush every 6 months or more frequently if it becomes clogged due to a residue buildup To wash Roll lint off the screen with your fingers Wet both sides of lint screen with hot water Wet a nylon brush with hot water and liquid detergent Scrub lint screen with the brush to remove residue buildup Rinse screen with hot water Thoroughly dry lint screen with a cle
7. Smart Delay touch CONNECT to override the delay and begin a dry cycle immediately DOWNLOAD amp GO OPTION Set a Specialty Cycle or My Cycle in the Whirlpool app and download it to your dryer The light above Download amp Go will illuminate indicating that the cycle has been received Touch DOWNLOAD amp GO to select the cycle for use See Using Your Dryer Smart Operation for details REMOTE START To start a dryer cycle remotely from the Whirlpool app touch and hold DOWNLOAD amp GO for about 3 seconds The Remote Start status indicator 6 and the indicator above the Start Pause button 3 will begin blinking Touch and hold START PAUSE to set the mode The indicator above Start Pause will go out and the Remote Start indicator will be solidly lit NOTE Any interaction with the dryer once a Remote Start has been set will cause the mode to cancel See Using Your Dryer Smart Operation for details Check Lint 9 HOWTO DRY e Normal Sanitize Gentle Steam Refresh Timed Dry a Hold to Start steam No Heat Hot o o o o o Less More Pepy asa o o o o Temperature Diyness EcoBoost Dryness EcoBoost Ea NOTE The control panel features a sensitive surface that responds to a light touch of your finger To ensure your selections are registered touch the control panel with your finger tip not your fingernail When selecting a setting or option simply touch its nam
8. gt e Whirlpool Use amp Care Guide Smart Electronic Dryer f Para obtener acceso al Manual de uso y cuidado en espa ol o para obtener informaci n adicional acerca de su producto visite www whirlpool com Get the app and connect instructions terms of use and privacy policy at www whirlpool com connect If you have any problems or questions call Whirlpool Corporation Connected Appliances at 1 866 333 4591 W10722883A W10722884A SP Table of Contents Dryer Safety Rincon 3 Check Your Vent System for Good Air Flow 5 Dryer Overview Connectivity Features o a aa aaa aaa aa paaa aa 6 Dryer Performance Features a a 7 Control Panel uu u u uuu uyu uu E ETE ici 8 Connectivity Selina 10 o An A 12 Using Your Dryer o uu u u LUT SU uuu ke cncetnccscensenaaactaccsessescaneuseetecdasunes 14 Smart Operatioiu uuu u in 16 Additional Features u u tic 17 Dryer Care is 18 Troubleshooting COnnectiVily uuu au css 20 Dryer OBp erati u u L L ZU u aussi aaea Aa Gaa dia eaa E Saida 21 Connected Appliance Regulatory Notices FCC and IC Compliance nin 24 Open Source License Usage 25 Warranty u auqa ssusasaasqasuaakukuwqusaaqanqhaskhaunuwwanaqausaqakkuswawaakasasasasuluuukussaaasasassshawhuwuasuqaq 26 As
9. Dryer Overview Control Panel WHATTO DRY e Mixed A e On j e Casuals Towels e Delicates e Bulky Sheets Wrinkle Shield e Static Reduce Download 8 Go Hold 3 Sec Remote Start Connect EndBeep Damp Beep Finishing Touch POWER BUTTON Touch to turn the dryer on and off Touch to stop cancel a cycle at any time WHAT TO DRY HOW TO DRY First select a cycle from the What to Dry Automatic cycles and then select the How to Dry to get the best combination cycle available for the type of items you are going to dry See Cycle Guide for cycle details START PAUSE BUTTON Touch and hold until the LED comes on to start a cycle or touch once while a cycle is in process to pause it The LED turns off at the end of a cycle It will flash when in a paused state or when waiting for you to touch Start Pause after setting the dryer for Remote Start mode LED DISPLAY When you select a cycle its default settings will light up and the Estimated Time Remaining for Automatic Cycles will vary depending on What to Dry and How to Dry selections or actual time remaining for Timed Dry cycles for Manual Cycles will be displayed CONNECT BUTTON Touch CONNECT during the initial connection of the dryer to your home Wi Fi network The Wi Fi status indicator 6 will be lit when the dryer is connected to the network See Connectivity Setup section for details If the dryer is ina
10. START PAUSE to begin the cycle 8 Remove garments promptly after cycle is finished Promptly remove garments after cycle has completed to reduce wrinkling Changing the Automatic Cycle settings to increase or decrease drying time If all your loads on all Automatic Cycles are consistently less dry or more dry than you would like you may change the default settings to increase or decrease the default dryness level Your automatic drying settings can be adjusted to adapt to different installations environmental conditions or personal preference This change is retained and will affect all of your Automatic Cycles not just the current cycle load There are 5 drying settings which are displayed using the time display O Much wetter clothes 30 less drying time Slightly wetter clothes 15 less drying time 1 2 Factory preset dryness level 3 Slightly drier clothes 15 more drying time 4 Much drier clothes 30 more drying time To change the drying settings NOTE The settings cannot be changed while the dryer is running or paused The dryer must be in standby mode power is off to adjust the default settings Before starting a cycle touch and hold DRYNESS for 6 seconds Touch DRYNESS to select the dryness level shown in the time display 0 1 2 3 or 4 Touch and hold START PAUSE to save the new dryness level setting 15 Using Your Dryer Smart Operation NOTE You must have successfully comple
11. START PAUSE to set the mode The indicator above Start Pause will go out and the Remote Start indicator will be solidly lit When a Remote Start command is received from the app the dryer will start the cycle causing the indicator above Start Pause to be lit indicating running state The Remote Start indicator will remain lit HELPFUL TIP Make sure that your dryer remains closed and the cycle is not adjusted until you start the cycle Any interaction with the dryer itself after a Remote Start has been set will cancel the Remote Start If the dryer needs to be paused to add garments the Remote Start will need to be reinitiated NOTE If no Wi Fi connection is available the Remote Start will not be set The Wi Fi indicator will blink for 2 seconds then go out If the dryer is Wi Fi connected but the Whirlpool app service is temporarily unavailable Remote Start can be set Additional Features USING THE DRYING RACK USING THE DRYING RACK cont To obtain a drying rack for your dryer order by calling Close the door 1 877 944 7566 You will need your model and serial Select a Timed Dry Air Only or Low Temperature cycle number and the purchase date Remove and discard any Items containing foam rubber or plastic must be dried packing material before use on a clothesline or by using the Air Only setting Use the Drying Rack for items that you do not want to When the cycle is selected the Estimated Time tumble d
12. Timed Dry Adjust Touch or with Timed Dry cycle to increase or decrease the length of the cycle O OPTIONS Use to select available options for your dryer Static Reduce Touch to add the Static Reduce option to selected Automatic cycles The dryer will automatically tumble pause and introduce a small amount of moisture into the load to help reduce static This option adds approximately 8 minutes to the total cycle time End Beep Use this to turn the signal indicating the end of a drying cycle to low medium high or off NOTE You may also turn off the tones that sound when a feature setting or option is touched Touch and hold End Beep for about three seconds to turn sounds to low medium high or off Damp Beep Touch to select the Damp Beep signal You may adjust the signal to low medium high or off When selected a series of beeps will sound when the load is damp but not completely dry This will allow you to take clothes out of the load that do not need to dry completely This option is available on some cycles The Damp Beep signal is selected as a default for the Bulky Sheets cycle as a reminder to manually reposition bulky loads midway through the cycle Wrinkle Shield Option If you will be unable to remove a load immediately touch Wrinkle Shield to add up to 150 minutes of periodic tumbling to help reduce wrinkling NOTE If you open the dryer door prior to the end of the Wrink
13. create an online user account If you already have the app and a user account please skip ahead to Register your dryer in your user account Register your dryer in your user account 3 Download app From your mobile device smartphone or tablet go to www whirlpool com connect and follow the instructions to download and install the Whirlpool app Registering your dryer in your account is a necessary step in 4 Account setup order for you to take full advantage of the Smart Features When prompted by the app enter the Smart Appliance Identification Number SAID case sensitive which can be found on a sticker inside the dryer door My Smart Appliance ID is SET UP O NOTES e Once you ve connected your dryer to your home Wi Fi network it will remain linked even if the power goes out you move the appliance or if you put it in storage for a while If you replace your wireless router or get a different Smart Dryer you will need to repeat this connectivity setup process Once installed tap the Whirlpool app icon to run the app You will be guided through the steps to set up a user account The app will make sure to get the necessary personal and home information as well as information about your energy company Subject to terms of use and privacy policy at www whirlpool com connect 11 Cycle Guide The Whirlpool Cabrio dryer has a unique user interface to help you select the best
14. of the vent system as improper venting installation will reduce air flow and at least every 2 years When cleaning is complete be dryer performance sure to follow the Installation Instructions supplied with Service calls caused by improper venting are not covered by your dryer for final product check the warranty and will be paid by the customer regardless of Clear away items from the front of the dryer who installed the dryer To clean or repair venting contact a venting specialist Dryer Overview Connectivity Features Wi Fi connectivity allows your Smart Dryer to connect to the Internet and interact with the Whirlpool app from your smartphone or mobile device This connection opens up several Smart options to you options intended to save you valuable time and energy A SMART FEATURES Smart Features help make your everyday a little more efficient by letting you remotely monitor manage and maintain your dryer Remote Start amp Pause What it does Allows you to send remote control of your dryer to your smartphone or mobile device via the Whirlpool app What it does for you Lets you manage when to start your dryer cycle and when your laundry gets done Have freshly dried laundry when you re ready for it not just when you re home to wait Cycle Progress What it does Gives you an up to the minute look at your dryer cycle progress and remaining cycle time from anywhere What it does fo
15. or reset the circuit breaker e Confirm that the power cord is properly installed Refer to the Installation Instructions for details e Select a Timed Dry heated cycle and restart the dryer If the message persists consult a qualified electrician If a code beginning with an F appears in the display alternating between F and E the dryer control has detected a problem that requires service Call for service The dryer will continue to run when this diagnostic code is present Touch any key to clear the code from the display and return to the estimated time remaining Try the following e Clean lint screen e Check to see if the vent run from the dryer to the wall is crushed or kinked e Confirm that the vent run from the dryer to the wall is free of lint and debris e Confirm that the exterior vent exhaust hood is free of lint and debris e Confirm that your vent system falls within the recommended run length and number of elbows for the type of vent you are using Refer to Plan Vent System in the Installaton Instructions for details Select a Timed Dry heated cycle and restart the dryer If the message persists have your entire home venting run cleaned Contact a venting specialist 23 Connected Appliance Regulatory Notices Federal Communications Commission FCC Compliance Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of th
16. All rights reserved Redistribution and use in source and binary forms with or without modification are permitted provided that the following conditions are met e Redistributions of source code must retain the above copyright notice this list of conditions and the following disclaimer e Redistributions in binary form must reproduce the above copyright notice this list of conditions and the following disclaimer in the documentation and or other materials provided with the distribution e Neither the name of the Eclipse Foundation Inc nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE Po
17. E F1 E1 F3 E1 etc variable service codes The dryer is in need of service AF restricted air flow The lint screen or vent is clogged the vent is crushed kinked or has too many turns Possible Causes Make sure water is connected to the dryer Check that water inlet hose is connected to both the faucet and dryer s water inlet valve Check that the water supply is turned on To remove odors left in garments after wearing select Steam Refresh This cycle is best for reducing wrinkles and odors from dry loads consisting of wrinkle free cotton cotton polyester blends common knits and synthetics Rerun a Steam Refresh cycle If necessary turn off Smart Grid monitoring during the cycle to prevent interruption Allow the dryer to complete the cooldown portion of the cycle before removing the load Select an Automatic Cycle with a lower heat setting to avoid overdrying the load The drying cycle has been interrupted Touch and hold START PAUSE to restart the dryer or press by a power failure POWER to clear the display The dryer will continue to run when this diagnostic code is present Touch any pad to clear the code from the display and return to the estimated time remaining NOTE This error will only show during the initial installation Try the following e Check to see if a household fuse has blown or circuit breaker has tripped Electric dryers use two household fuses or breakers Replace the fuse
18. G3 The OEM of the XPWG3 Module must only use the approved antenna s which have been certified with this module The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product The user manual for the end product must include the following information in a prominent location To comply with FCC and Industry Canada RF radiation exposure limits for general population the antenna s used for this transmitter must be installed such that a minimum separation distance of 20 cm is maintained between the radiator antenna and all persons at all times and must not be co located or operating in conjunction with any other antenna or transmitter Connected Appliance Regulatory Notices cont Open Source License Usage The following statements refer to the portions of this software based in part on FreeRTOS v7 0 2 http www freertos org The use of this software is governed by the terms of GNU General Public License v 2 which is available at http www gnu org licenses gpl 2 0 html A copy of the source code may be obtained by written request for the software by name to opensourceOwhirlpool com along with the address for delivery The following statements refer to those portions of the software copyrighted by Eclipse Foundation Inc Copyright c 2007 Eclipse Foundation Inc and its licensors
19. Whiripoolmw a be OEE Touch CONNECT to turn Smart Grid feature on Smart Grid functions Connection to the Whirlpool app Check if the blue Smart Grid indicator is blinking do not work and Smart Grid service may be unavailable User account has not been properly See Connectivity Setup section or the Whirlpool app directly set up or the dryer has not been for account setup and dryer registration instructions registered in an acoount Verify that the dryer is paired with your account in the app Verify correct e mail address mobile number and notification preferences 20 Troubleshooting Dryer Operation First try the solutions suggested here or visit our website at www whirlpool com product_help If you experience Possible Causes ET Dryer Operation Dryer will not run Door not closed completely Make sure the dryer door is closed completely START PAUSE touched with Touch and hold START PAUSE with pad of finger fingernail Household fuse is blown or circuit breaker has tripped There may be 2 household fuses or circuit breakers for the dryer Check that both fuses are intact and tight or that both circuit breakers have not tripped Replace the fuses or reset the circuit breaker If the problem continues call an electrician Incorrect power supply Electric dryers require 240 volt power supply Check with a qualified electrician Wrong type of fuse Use a time delay fuse Dryer will not turn off Dr
20. an towel Reinstall screen in dryer NON USE STORAGE AND MOVING CARE Steam models only Install and store your dryer where it will not freeze Because some water may stay in the hose freezing can damage your dryer If storing or moving your dryer during freezing weather winterize it Non Use or Storage Care If you will be on vacation or not using your dryer for an extended period of time you should Unplug dryer or disconnect power Clean lint screen See Cleaning the Lint Screen Turn off the water supply to the dryer This helps to avoid unintended flooding due to a water pressure surge while you are away Moving Care For power supply cord connected dryers Unplug the power supply cord Gas models only Close shut off valve in gas supply line Gas models only Disconnect gas supply line pipe and remove fittings attached to dryer pipe Gas models only Cap the open fuel supply line Steam models only Shut off water faucet Disconnect the water inlet hose from faucet then drain the hose Transport hose separately Make sure leveling legs are secure in dryer base Use tape to secure dryer door AWARNING y Electrical Shock Hazard Disconnect power before servicing Replace all parts and panels before operating Failure to do so can result in death or electrical shock For direct wired dryers 1 Disconnect power 2 Disconnect wiring 3 Steam models only Shut off water fauc
21. care and energy savings By answering these questions you can achieve the most energy savings and enhanced fabric care from your dryer Using these automatic cycles the drying air temperature and moisture levels are sensed in the load This sensing process occurs throughout the entire drying cycle and turns off once the load reaches your selected dryness level Using a dryness level between Less and More provides the optimal energy savings If Timed Dry is your answer the dryer runs for the amount of time you select which sometimes results in shrinkage wrinkling and static due to overdrying Use Timed Dry for the occasional damp load that needs a little more drying time or when using the drying rack Tips for getting the best performance from your steam dryer E Results may vary depending on fabric 100 cotton E Cycles that use steam are not recommended for items that garments with wrinkle free finish may yield better results have been starched Wash any starched or new garments than those without 100 cotton items may require prior to using a cycle that uses steam additional touching up after cycles that use steam E The Steam Refresh Cycle is best for smoothing out wrinkles E Use of fabric softener sheet is not recommended with and reducing odors from loads consisting of dry items of cycles that use steam It may cause temporary staining wrinkle free cotton cotton polyester blend common knits on clothes and synthetics
22. cked Dry smaller loads that can tumble freely Results may also vary depending on fabric type For steam cycles the water is not Make sure water is connected to the dryer Check that water properly connected with the dryer inlet hose is connected to both the faucet and dryer s water inlet valve Check that the water supply is turned on A Smart Grid event may have Rerun a Steam Refresh cycle If necessary turn off Smart Grid interrupted the Steam Refresh cycle monitoring during the cycle to prevent interruption Recent painting staining or Ventilate the area When the odors or fumes are gone from the varnishing in the area where your area rewash and dry the clothing dryer is located 22 Troubleshooting Dryer Operation First try the solutions suggested here or visit our website at www whirlpool com product_help If you experience Dryer Results cont Odors cont For steam cycles the water is not properly connected with the dryer Odors are left in garments after wearing A Smart Grid event may have interrupted the Steam Refresh cycle Load removed before cooldown portion of cycle complete Using Timed Dry cycle with a high temperature setting Load too hot Dryer Displaying Code Message or Indicator Is Lit PF power failure L2 Diagnostic Code low or no line voltage condition There may be a problem with your home power supply keeping the dryer s heater from turning on FR
23. cycle you need for your load The What to Dry How to Dry layout guides you to the optimal cycle in two easy steps First determine what items are in the load that you are trying to dry Use that to guide your What to Dry selection Then determine how you want the dryer to dry them by selecting the appropriate How to Dry selection To get the most energy savings and enhanced fabric care from your dryer use the Automatic cycles These cycles measure the drying air temperature and moisture levels to turn the dryer off once the load reaches the selected dryness level Dryer performance and results may vary with service voltage less than 240 See Dryer Overview Connectivity Features and Using Your Dryer Smart Operation to learn about downloading and using additional dryer cycles from your Whirlpool app How do you want to dry How to Dry Cycle Selection For best fabric care choose the cycle that best fits the load being dried R Recommended Cycle a Alternate Cycle Blank Cycle is available What do you want to dry Baby Clothes Handkerchiefs Pajamas Sweatshirts T Shirts Business Casual Cotton Drapes Dress Shirts Pants Machine Wash Curtains Napkins No lron Fabrics Tablecloth Dish Cloths Jeans Non Rubber Lined Rugs amp Mats Towels Performance Wear Bras Fabric Shower Curtain Lingerie Sheers Undergarments Wool 2
24. d by a Whirlpool designated humidi g nig g umidity or exposure to chemicals o p NO lo e r n 11 Pick up or delivery This product is intended for in home repalr y A 12 Travel or transportation expenses for service in remote locations where an authorized applies only when the major appliance Whirlpool servicer is not available is used in the country in which it was 13 Removal or reinstallation of inaccessible appliances or built in fixtures i e trim purchased This limited warranty is effective from the date of original consumer purchase Proof of original purchase date q 14 is required to obtain service under this limited warranty decorative panels flooring cabinetry islands countertops drywall etc that interfere with servicing removal or replacement of the product Service or parts for appliances with original model serial numbers removed altered or not easily determined The cost of repair or replacement under these excluded circumstances shall be borne by the customer DISCLAIMER OF IMPLIED WARRANTIES IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW Some states do not allow limitations on the duration of implied warranties of merchantability or fitness so this limitation may not apply to you This warranty gives you specific legal rights and you also may
25. e CONNECTIVITY STATUS INDICATORS P Remote Start Wi Fi Smart Delay SMART GRID STATUS INDICATORS A Blue The BLUE indicator will be lit during times of OFF PEAK energy demand Dry cycles will begin without delay upon touch and hold of the Start Pause button Amber The AMBER indicator will be lit during times of PEAK energy demand The dryer will go into Smart Delay mode upon touch and hold of the Start Pause button and the Smart Delay indicator 6 will illuminate When energy demand returns to OFF PEAK levels the AMBER indicator and Smart Delay indicator will go out the BLUE indicator will illuminate and the dry cycle will begin If Whirlpoo M app service is momentarily unavailable the Smart Grid status indicators will be OFF Touching Connect will cause the BLUE indicator to blink for 2 seconds and then stay OFF MODIFIERS Use to select available modifiers for your dryer Temperature When using Timed Dry Cycle you may select a dry temperature based on the type of load you are drying Use the warmest setting safe for the garments in the load Follow garment label instructions NOTE Automatic Cycles will give you up to 3 temperatures to adjust and it varies depending on the What to Dry or How to Dry selections that have been made Dryness You may adjust the Dryness on Automatic Cycles except for the Sanitize cycle if desired NOTE Dryness is for use with Automatic Cycles only
26. e FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy ana if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment RF Exposure Information To comply with FCC IC RF exposure requirements for mobile
27. ental or installation conditions you may Steam Refresh cycle with damp experience underdrying preus pola When using the Steam Refresh cycle for a single item it is recommended to throw a towel in the dryer to prevent damp spots The automatic cycle is ending early Change the dryness level setting on Automatic Cycles Increasing or decreasing the dryness level will change the amount of drying time in a cycle If loads are consistently ending too early see also Changing the Automatic Cycle settings to increase or decrease drying time Lint on load Lint screen is clogged with lint Clean lint screen before each load Stains on load Improper use of fabric softener Add dryer fabric softener sheets at the beginning of the cycle Fabric softener sheets added to a partially dried load can stain your garments Do not use fabric softener sheets with steam cycles Stains on drum Loose dyes in clothes Drum stains are caused by dyes in clothing usually blue jeans These will not transfer to other clothing Loads are wrinkled The load was not removed from dryer Select Steam Refresh cycle to tumble the load with water and at the end of the cycle heat This cycle is best for smoothing out wrinkles and reducing odors from dry loads consisting of wrinkle free cotton cotton polyester blends common knits and synthetics NOTE Refer to garment care label instructions Dry clean only garments are not recommended The dryer was tightly pa
28. ervice center directly from the Whirlpool app SMART ABOUT ENERGY Your Smart Dryer can monitor and respond to changing energy demand levels on the power grid Smart Delay Opt In What it does When energy demand is high it gives you the option to delay starting a dryer cycle until demand levels are lower What it does for you You can feel good about giving a little back to the environment Some consumers may even see a lower energy bill If you need to begin a dryer cycle immediately you can override a Smart Delay The dryer will return to energy monitoring on the next cycle GET STARTED Refer to the Quick Connect packet that came with your dryer or see the Connectivity Setup section on pages 10 and 11 of this Use amp Care Guide and follow the instructions to get connected Check the Whirlpool app frequently for additional information and features Dryer Overview Dryer Performance Features EcoBoost option Touch to activate the EcoBoost option which allows you to increase your energy savings by using a slightly lower heat level For automatic cycles the EcoBoost M option will increase drying times by approximately 40 minutes the LED Display will reflect this time The EcoBoost option will default on for Normal For optimal energy turn on the EcoBoost option For optimal time turn off the EcoBoost option Not available on all cycles What To Dry and How To Dry for better fabric
29. et 4 Steam models only Disconnect the water inlet hose from faucet then drain the hose Transport hose separately 5 Make sure leveling legs are secure in dryer base 6 Use tape to secure dryer door Reinstalling the Dryer Follow the Installation Instructions to locate level and connect the dryer SPECIAL INSTRUCTIONS FOR STEAM MODELS Water Inlet Hose Replace inlet hose and hose screen after 5 years of use to reduce the risk of hose failure Periodically inspect and replace inlet hose if bulges kinks cuts wear or leaks are found When replacing your inlet hose record the date of replacement To Winterize the Dryer 1 Unplug dryer or disconnect power 2 Shut off water faucet 3 Disconnect water inlet hose from faucet and drain To Use the Dryer Again 1 Flush water pipes Reconnect water inlet hose to faucet Turn on water faucet 2 Plug in dryer or reconnect power as described in the Installation Instructions 19 Troubleshooting Connectivity Connection Status Control Panel Indicator Lights Dryer is not connected e Wi Fi icon is OFF e Smart Grid icons are OFF Dryer is attempting to connect to home e Wi Fi icon is blinking slowly Wi Fi router Dryer is connected to home Wi Fi router but e Wi Fi icon is ON Whirlpool app or Smart Grid functions do not work e Blue Smart Grid icon is blinking slowly Dryer is connected to home Wi Fi router and the e Wi Fi icon is ON Whirlpool M a
30. have other rights that vary from state to state DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY Whirlpool makes no representations about the quality durability or need for service or repair of this major appliance other than the representations contained in this Warranty If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance you should ask Whirlpool or your retailer about buying an extended warranty LIMITATION OF REMEDIES EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES Some states do not allow the exclusion or limitation of incidental or consequential damages so these limitations and exclusions may not apply to you This warranty gives you specific legal rights and you also may have other rights that vary from state to state 03 15 26 Notes 27 Assistance or Service Before calling for assistance or service please check Troubleshooting or visit www whirlpool com lt may save you the cost of a service call If you still need help follow the instructions below When calling please know the purchase date and the complete model and serial number of your appliance This information will help us to better respond to your request If you need replacement parts or to order accessories We recomme
31. in this list having a gain La al than the maximum gain indicated for that type are strictly prohibited for use with this device Antenna Maximum Permissible Required Type Antenna Gain dBi Impedance OHM Slot 1 76 50 To comply with FCC and Industry Canada RF radiation exposure limits for general s the antenna s used for this transmitter must be installed such that a minimum separation distance of 20 cm is maintained between the radiator antenna and all persons at all times and must not be co located or operating in conjunction with any other antenna or transmitter Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 appareil ne doit pas produire de brouillage et 2 Putilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement 24 Conform ment la r glementation d Industrie Canada le pr sent metteur radio peut fonctionner avec une antenne d un type et d un gain maximal ou inf rieur approuv pour l metteur par Industrie Canada Dans le but de r duire les risques de brouillage radio lectrique l intention des autres utilisateurs il faut choisir le type d antenne et son gain de sorte que la puissance isotrope rayonn e quivalente p i r e ne d passe pas l intensit
32. le Failure to follow these instructions can result in death or fire 2 Load the dryer eS Open the door by pulling on the handle Place laundry in the dryer Add a dryer sheet to wet load if desired Close the door IMPORTANT Do not tightly pack the dryer Items need to tumble freely Tightly packing can lead to poor drying performance and may increase wrinkling and tangling 3 Touch POWER Touch POWER to turn on the dryer 4 Select type of load to dry WHAT TO DRY e Mixed e Casuals e Towels Delicates Bulky Sheets HOW TO DRY e Normal Sanitize e Gentle e Steam Refresh Timed Dry First select a cycle from the What to Dry Automatic cycles and then select the How to Dry to get the best combination cycle available for the type of items you are going to dry See Cycle Guide for cycle details Not all cycles are available on all models Automatic Cycles You can select a different dryness level depending on your load Touch DRYNESS to scroll to Less to More Selecting Less to More automatically adjusts the dryness level at which the dryer will shut off Dryness level can be changed in the first 5 8 minutes of the cycle Automatic Cycles give the best drying in the shortest time Drying time varies based on fabric type load size and dryness setting NOTE Automatic Cycles will give you up to 3 temperatures to adjust and it varies depending on the What to Dry or How
33. le Shield option the dryer will go into Pause mode You will need to touch Power to turn off or touch Start Pause to continue Wrinkle Shield option EcoBoost Option Touch to activate the EcoBoost option which allows you to increase your energy savings by using a slightly lower heat level This will increase dry times EcoBoost option will default on for Mixed Normal Can be selected for Mixed Gentle Casual Normal Casual Gentle Delicate Normal and Delicate Gentle It will be not available for the other cycles Steam Refresh This cycle is best for reducing wrinkles and odors from dry items Cycle time will increase depending on number of items Connectivity Setup IMPORTANT Proper installation of your dryer prior to use is your responsibility Be sure to read and follow the Installation Instructions that came with your dryer Automatic Setup Instructions Wi Fi Protected Setup WPS You will need e Ahome wireless router capable of Wi Fi Protected Setup WPS The router should be on and have a live Internet connection e The Smart Appliance ID SAID from your dryer This is located on a sticker inside the dryer door NOTE If your home wireless router is not equipped with a WPS button please check the user manual of your router to confirm if it is WPS capable If not alternate setup instructions are at www whirlpool com connect 1 Router setup INTERNET WI FI PROTECTED SETUP WPS B Q
34. line away from dryer Place dryer at least 18 inches 460 mm above the floor for a garage installation Failure to do so can result in death explosion or fire CLEANING THE DRYER INTERIOR To clean dryer drum Use a mild hand dish detergent mixed at a low concentration with very warm water and rub with a soft cloth Rinse well with a wet sponge or towel Tumble a load of clean clothes or towels to dry drum OR Use a microfiber cloth and hot water in a spray bottle to clean the drum and a second microfiber towel to dry NOTE Garments that contain unstable dyes such as denim blue jeans or brightly colored cotton items may discolor the rear of the dryer interior These stains are not harmful to your dryer and will not stain future loads of clothes Dry unstable dye items inside out to avoid transfer of dye REMOVING ACCUMULATED LINT From Inside the Dryer Cabinet Lint should be removed every 2 years or more often depending on dryer usage Cleaning should be done by a qualified appliance servicer or ventilation system cleaner From the Exhaust Vent Lint should be removed every 2 years or more often depending on dryer usage CLEANING THE LINT SCREEN Every load cleaning The lint screen is located in the door opening of the dryer The control panel has an indicator light Check Lint to remind you to clean the lint screen after each load A screen blocked by lint can increase drying time To clean 1
35. moisture sensors during Automatic cycles See Level Dryer in the Installation Instructions Select the correct temperature for the types of garments being dried See Cycle Guide Troubleshooting Dryer Operation First try the solutions suggested here or visit our website at www whirlpool com product_help If you experience Possible Causes ET Dryer Results cont Drying times are too The load is too large and heavy to dry Separate the load to tumble freely long and clothes are not quickly getting dry Fabric softener sheets are blocking The air outlet grille is just inside the door behind the lint screen the grille Check that it is not blocked by a fabric softener sheet Use only one fabric softener sheet and use it only once The dryer is located in a room with Proper operation of dryer cycles requires temperatures above temperature below 45 F 7 C 45 F 7 C The dryer is located in a closet Closet doors must have ventilation openings at the top and bottom of the door The front of the dryer requires a minimum of 1 25 mm of airspace and for most installations the rear of the dryer requires 5 127 mm See the Installation Instructions Cycle time is too short The load may not be contacting the Level the dryer See the Installation Instructions All four dryer sensor strips on Automatic Cycles feet should be in firm contact with the floor Clothes are coming out of the Under certain environm
36. nd that you use only FSP Factory Specified Parts These parts will fit right and work right because they are made with the same precision used to build every new WHIRLPOOL appliance To locate FSP replacement parts assistance in your area or accessories Whirlpool Corporation Customer eXperience Center 1 866 333 4591 www whirlpool com connect Our consultants provide assistance with For more assistance Use and maintenance procedures You can write with any questions or concerns at Accessory and repair parts sales Whirlpool Corporation Referrals to local dealers repair parts distributors Customer eXperience Center and service companies Whirlpool designated service 553 Benson Road technicians are trained to fulfill the product warranty Benton Harbor MI 49022 2692 and provide after warranty service anywhere in the Please include a daytime phone number United States in your correspondence W10722883A 03 15 W10722884A SP 2015 Whirlpool All rights reserved Printed in U S A
37. not always be detected by smell Gas suppliers recommend that you use a gas detector approved by UL or CSA For more information contact your gas supplier If a gas leak is detected follow the What to do if you smell gas instructions State of California Proposition 65 Warnings WARNING This product contains one or more chemicals known to the State of California to cause cancer WARNING This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm Check Your Vent System For Good Air Flow 4 WARNING Maintain good air flow by E Cleaning your lint screen before each load E Replace plastic or foil vent material with 4 102 mm diameter heavy rigid vent material Fire Hazard Use the shortest length of vent possible Use no more than four 90 elbows in a vent system Do not use a plastic vent each bend and curve reduces air flow Do not use a metal foil vent Use a heavy metal vent Failure to follow these instructions can result in death Good Better or fire Good air flow Along with heat dryers require good air flow to efficiently dry laundry Proper venting will reduce your drying times and improve your energy savings See Installation Instructions The venting system attached to the dryer plays a big Remove lint and debris from the exhaust hood role in good air flow Blocked or crushed vents as well Remove lint from the entire length
38. nt Before the dryer is removed from service or discarded surrounding areas free from the accumulation of lint dust remove the door to the drying compartment and dirt Do not reach into the dryer if the drum is moving The interior of the dryer and exhaust vent should be Do not install or store the dryer where it will be exposed cleaned periodically by qualified service personnel to the weather See Electrical Requirements located in the installation Do not tamper with controls instructions for grounding instructions SAVE THESE INSTRUCTIONS Do not dry articles that have been previously cleaned in washed in soaked in or spotted with gasoline dry WARNING For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage personal injury or death Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance WHAT TO DO IF YOU SMELL GAS e Do not try to light any appliance e Do not touch any electrical switch do not use any phone in your building e Clear the room building or area of all occupants e Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions e If you cannot reach your gas supplier call the fire department Installation and service must be performed by a qualified installer service agency or the gas supplier WARNING Gas leaks can
39. one number m Model number and serial number LI M ITED WAR RANTY m A clear detailed description of the problem m Proof of purchase including dealer or retailer name and address IF YOU NEED SERVICE s s 1 Before contacting us to arrange service please determine whether your product requires repair Some questions can be addressed without service Please take a few minutes to review the Troubleshooting or Problem Solver section of the Use and Care Guide scan the QR code on 5 the right to access additional resources or visit https www whirlpool com product_help Ji 2 All warranty service is provided exclusively by our authorized Whirlpool Service Providers s E Direct all requests for warranty service to https www whirlpool com product_help Whirlpool Customer eXperience Center Call 1 866 333 4591 ONE YEAR LIMITED WARRANTY WHAT IS COVERED WHAT IS NOT COVERED For one year from the date of purchase 1 Commercial non residential multiple family use or use inconsistent with published user when this major appliance is installed operator or installation instructions operated and maintained according 2 In home instruction on how to use your product to instructions attached to or furnished 3 Service to correct improper product maintenance or installation installation not in with the product Whirlpool Corporation accordance with electrical or plumbing codes or correction of household electrical or hereafte
40. perating in conjunction with any other antenna or transmitter As long as the two conditions above are met further transmitter testing will not be required However the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed for example digital device emissions PC peripheral requirements etc IMPORTANT NOTE In the event that these conditions cannot be met for certain configurations or co location with another transmitter then the FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number cannot be used on the final product In these circumstances the OEM integrator will be responsible for re evaluating the end product including the transmitter and obtaining a separate FCC and Industry Canada authorization End Product Labeling The XPWG3 Module is labeled with its own FCC ID and IC Certification Number If the FCC ID and IC Certification Number are not visible when the module is installed inside another device then the outside of the device into which the module is installed must also display a label referring to the enclosed module In that case the final end product must be labeled in a visible area with the following Contains Transmitter Module FCC ID ASUXPWG3 Contains Transmitter Module IC 10248A XPWG3 or Contains FCC ID A5UXPWG3 Contains IC 10248A XPW
41. pp works e Smart Grid icon is either ON or OFF it is not blinking First try the solutions suggested here or visit our website at www whirlpool com connect if you experience Possible Causes x Solution O Dryer is not connected The dryer may be in standby mode Touch the POWER button on the dryer and observe indicators to home Wi Fi router All indicator lights are off when in standby mode Wi Fi icon is OFF The dryer has never been connected See Connectivity Setup section to the home Wi Fi router The dryer has been connected to Press CONNECT The Wi Fi icon should blink while connecting the home Wi Fi router but dryer this may take up to 2 minutes Wi Fi is OFF Lost connection to home Wi Fi router Check whether the router is on and working with other computers or devices in the home able to access the Internet Weak signal strength or signal Try to place the wireless router closer to the dryer It may be interference between the dryer necessary to install a Wi Fi range extender and router Wi Fi icon does not light Something may be wrong with the Unplug or disconnect dryer power for 30 seconds Return power at all after pressing the dryer Repeat Wi Fi connect process Connect button Verify that the dryer operates correctly except for not being able to connect Call for service Dryer is connected to Smart Grid features on the dryer may Check whether either Smart Grid indicator is on continuously
42. r Whirlpool will pay for plumbing i e house wiring fuses or water inlet hoses Factory Specified Replacement Parts 4 Consumable parts i e light bulbs batteries air or water filters preservation solutions and repair labor to correct defects etc in materials or workmanship that existed Defects or damage caused by the use of non genuine Whirlpool parts or accessories when this major appliance was purchased Conversion of your product from natural gas or L P gas or reversal of appliance doors or at its sole discretion replace the product Damage from accident misuse abuse fire floods acts of God or use with products not In the event of product replacement your approved by Whirlpool appliance will be warranted by the remaining Repairs to parts or systems to correct product damage or defects caused by term of the original unit s warranty period unauthorized service alteration or modification of the appliance Cosmetic damage including scratches dents chips and other damage to appliance YOUR SOLE AND EXCLUSIVE REMEDY finishes unless such damage results from defects in materials and workmanship and is UNDER THIS LIMITED WARRANTY ayi reported to Whirlpool within 30 days SHALL BE PRODUCT REPAIR AS er A 10 Discoloration rust or oxidation of surfaces resulting from caustic or corrosive PROVIDED HEREIN Service must be environments including but not limited to high salt concentrations high moisture or provide
43. r you Relieves you of having to visit the laundry room to check on the status of your dryer cycle Clothes Dry Notification Opt In What it does Your dryer will send you a push notification when its current cycle is complete What it does for you Alerts you precisely when the dryer is done so you can get the next load started and move on to other things If you can t unload the dryer right away or are away from home when a cycle finishes you can remotely activate Wrinkle Shield cycles to help your clothes stay fresh until you re able to get to them Specialty Cycles amp My Cycle What it does Allows you to browse additional dryer cycles available in the Whirlpool app and download a cycle to the dryer with the Download amp Go option You can also create and save your own customized cycles What it does for you Takes the guesswork out of selecting the optimal dryer settings for garments and household items that require specialized care Quiet Mode What it does Lets you turn off the tones and beeps coming from your dryer What it does for you Allows you to do laundry without disturbing anyone else in the household Issue Alerts Opt In What it does Sends you a push notification if something has gone wrong What it does for you Gives you a heads up and provides guidance to fix simple issues through videos and step by step instructions If the issue is more complex you can e mail or call our s
44. ring The dryer may vibrate if not properly installed See the Installation Instructions All four dryer feet should be in firm contact with the floor When balled up the load will bounce causing the dryer to vibrate Separate the load items and restart the dryer Clicking noise Gas valve operating On gas dryers you may hear the gas valve clicking as it opens and closes This is normal Dryer Results Drying times are too long and clothes are not getting dry Lint screen or lint screen housing is clogged with lint The exhaust vent or outside exhaust hood is clogged with lint restricting air movement The exhaust vent is not the correct length The exhaust vent diameter is not the correct size The dryer is not level The No Heat temperature setting has been selected Clean lint screen before each load Clean space where lint screen is located as needed Using a vacuum gently remove any lint that has accumulated outside of the lint screen Run the dryer for 5 10 minutes Hold your hand under the outside exhaust hood to check air movement If you do not feel air movement clean exhaust system of lint or replace exhaust vent with heavy metal or flexible metal vent See the Installation Instructions Check that the exhaust vent is not too long or has too many turns Long venting will increase drying times See the Installation Instructions Use 4 102 mm diameter vent material Clothes not contacting the
45. rtions of this software are copyright c Sawtooth Consulting Ltd 2006 2015 All rights reserved Portions of this software are copyright c Arrayent Inc 2015 All rights reserved The following statements refer to those portions of the software copyrighted by Swedish Institute of Computer Science Copyright c 2001 2004 Swedish Institute of Computer Science All rights reserved Redistribution and use in source and binary forms with or without modification are permitted provided that the following conditions are met 1 Redistributions of source code must retain the above copyright notice this list of conditions and the following disclaimer 2 Redistributions in binary form must reproduce the above copyright notice this list of conditions and the following disclaimer in the documentation and or other materials provided with the distribution 3 The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission THIS SOFTWARE IS PROVIDED BY THE AUTHOR AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS
46. ry such as sweaters and tennis shoes When you Remaining display shows the detault time You ran use the drying rack the drum continues to turn but the change the actual time in the cycle by increasing or rack remains stationary decreasing the cycle time The drying rack is intended for use with the Manual Dry 7 Start the dryer Timed Dry cycles only The drying rack cannot be used with f Automatic cycles NOTE Check the lint screen and remove any lint accumulated from items dried on the drying rack after the To use the drying rack cycle is finished IMPORTANT Do not remove the lint screen 1 Open dryer door N 2 Align the two hooks on the front of the drying rack with the holes in the dryer door opening and press down fully into holes Rest the rear support on the dryer back ledge sN Place wet items on top of the drying rack Allow space around items for air to circulate The drying rack does not move but the drum will rotate be sure to leave adequate clearance between items and the inside of the dryer drum Make sure items do not hang over the edges or between drying rack grille 17 Dryer Care CLEANING THE DRYER LOCATION Keep dryer area clear and free from items that would block the air flow for proper dryer operation This includes clearing piles of laundry in front of the dryer AWARNING Explosion Hazard Keep flammable materials and vapors such as gaso
47. sistance or Service Q J Q T Back Cover Dryer Safety Your safety and the safety of others are very important We have provided many important safety messages in this manual and on your appliance Always read and obey all safety messages This is the safety alert symbol This symbol alerts you to potential hazards that can kill or hurt you and others All safety messages will follow the safety alert symbol and either the word DANGER or WARNING These words mean A You can be killed or seriously injured if you don t immediately DANGER follow instructions You can be killed or seriously injured if you don t foll 44 WARNING ae instructions All safety messages will tell you what the potential hazard is tell you how to reduce the chance of injury and tell you what can happen if the instructions are not followed A WARNING Risk of Fire Clothes dryer installation must be performed by a qualified installer Install the clothes dryer according to the manufacturer s instructions and local codes Do not install a clothes dryer with flexible plastic venting materials or flexible metal foil type duct If flexible metal duct is installed it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers Flexible venting materials are known to collapse be easily crushed and trap lint These condi
48. ted the Connectivity Setup section on pages 10 and 11 for the following features to function Verify that the Wi Fi status indicator is illuminated Check the Whirlpool app for additional dryer features including Delay Start Download a Specialty Cycle or My Cycle Download amp Go The Download amp Go option lets you select and send a Specialty Cycle or My Cycle from the Whirlpool app directly to your dryer The indicator above Download amp Go will illuminate Touch DOWNLOAD amp GO to select the cycle The Time Status display will show the estimated cycle time Touch and hold the START PAUSE button for 3 seconds as in Step 7 to start the dry cycle or continue to set the dryer for Remote Start HELPFUL TIP The cycle will be remembered for future use until a different cycle is downloaded to the dryer NOTE If the Download amp Go button is touched without a cycle ready for selection with the indicator not lit you will hear an Invalid Keypress sound if key activation sounds are turned on 16 Set a Remote Start Download amp Go Hold 3 Sec Remote Start Remote Start mode allows you to start your dryer remotely from the Whirlpool app After preparing your laundry load and selecting your cycle settings touch and hold the DOWNLOAD amp GO button for 3 seconds The Remote Start status indicator O and the indicator above the Start Pause button will begin blinking Touch and hold
49. tions will obstruct clothes dryer airflow and increase the risk of fire To reduce the risk of severe injury or death follow all installation instructions Save these instructions IMPORTANT When discarding or storing your old clothes dryer remove the door IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire electric shock or injury to persons when using the dryer follow basic precautions including the following Read all instructions before using the dryer Do nat repair or replace any part of the dryer or attempt Do not place items exposed to cooking oils in your dryer any servicing unless specifically recommended in this Items contaminated with cooking oils may contribute to Use and Care Guide or in published user repair f a chemical reaction that could cause a load to catch fire instructions that you understand and have the skills to carry out Do not use fabric softeners or products to eliminate static cleaning solvents or other flammable or explosive unless recommended by the manufacturer of the fabric substances as they give off vapors that could ignite or softener or product explode Do not use heat to dry articles containing foam rubber or Do not allow children to play on or in the dryer Close similarly textured rubber like materials supervision of children is necessary when the dryer is Clean lint screen before or after each load used near children Keep area around the exhaust opening and adjace
50. to Dry selections that have been made TIMED DRY Cycle When you select Timed Dry the default time appears in the display Touch and to increase or decrease the time in 1 minute increments Touch and hold to change the time in 5 minute increments The default temperature may be changed by pressing Temperature until the desired dry temperature is lit Steam Refresh Cycles If you will be unable to remove a load immediately touch FINISHING TOUCH twice to select Wrinkle Shield to add up to 150 minutes of periodic tumbling 5 Adjust cycle modifiers if desired No Heat Hot Less More Timed Dry Adjust e Temperature Dryness Check Lint You may adjust different settings lei 17 depending on what you are drying and ERE how you are going to dry the item See the Cycle Guide for detailed information n a NOTE Not all options and modifiers are available with all cycles 6 Select any additional options e Wrinkle Shield e e On e Static Reduce End Beep DampBeep Finishing Touch EcoBoost Add additional options such as Static Reduce Wrinkle Shield and or EcoBoost by touching that option If you will be unable to remove the load promptly select Wrinkle Shield before touching START PAUSE NOTE Not all options and settings are available with all cycles T Touch and hold START PAUSE to begin cycle Hold to Start Touch and hold
51. transmitting devices this transmitter should only be used or installed at locations where there is at least 20 cm separation distance between the antenna and all persons To comply with FCC IC RF exposure limits for general population uncontrolled exposure the antenna s used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co located or operating in conjunction with any other antenna or transmitter Industry Canada IC Compliance Notice This Device complies with Industry Canada License exempt RSS standard s Operation is subject to the following two conditions 1 This device may not cause interference 2 This device must accept any interference includin interference that may cause undesired operation of the device Under Industry Canada regulations this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for the transmitter by Industry Canada To reduce potential radio interference to other users the antenna type and Its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that necessary for successful communication This radio transmitter IC 10248A XPWG3 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated Antenna types not included
52. yer door was opened prior to the end of the Wrinkle Shield option Household fuse is blown or circuit breaker has tripped Dryer will not heat If you open the dryer door prior to the end of the Wrinkle Shield option the dryer will go into Pause mode You will need to touch Power to turn off or touch and hold Start Pause to continue Wrinkle Shield option The drum may be turning but you may not have heat Electric dryers use 2 household fuses or circuit breakers Replace the fuses or reset the circuit breaker If the problem continues call an electrician Incorrect power supply Electric dryers require 240 volt power supply Check with a qualified electrician Supply line valve not open For gas dryers make sure that the valve on the gas supply line is open Unusual Noise Humming or whining noise with Steam cycle selected Water pump on dryer is running The water pump on the dryer is used during the Steam function If the dryer has just been installed or unused for an extended period the pump may be louder and run longer This is normal Thumping noise Dryer hasn t been used in a while This is normal The thumping sound should diminish after a few minutes of use Rattling or vibrating noise Dryer isn t properly leveled Clothing is balled up in dryer A small object caught between the Check the front and rear edges of the drum for small objects edges of dryer drum Clean out pockets before launde
Download Pdf Manuals
Related Search