K44 Duo
Contents
1. 444 AAA A A Acts as a door bell button and starts the sequence telling the K44 Duo what to you want to program E g A21 to program codes B Press B and enter the 6 digit pass word to programme the K44 Duo Press B to leave the pro gramming mode 8 K44 Duo Installation amp User manual LED EXIT 1 CONTACT 1 TAMPER ov 14 5 EXIT 2 ab CONTACT 2 K44 Duo Installation 8 User manual Power in terminal nos 1 and 2 12 24 V Input for extra LED red terminal nos 3 and 4 10 35 VDC Tamper switch terminal nos 5 and 6 Closed when the housing is closed Code disabling from external time clock Input 1 Close terminal nos 8 and 7 Input 2 Close terminal nos 9 and 7 Output for alert or duress Use E7 relay Connect between terminal nos 10 and 1 Contact for zero 0 opening Close terminal nos 11 and 7 Output for Door bell buzzer Use E7 relay Connect between terminal nos 12 and 1 Input for door contacts The contact is closed when the door is closed Terminal nos 13 and 15 19 and 21 respectively Exit button The door opens on closing terminal nos 14 and 15 20 and 21 respectively Electric locking device Dashed line refers to locks with fail safe function SW1 push button Used when choosing password and erasing memory 10 K44 Duo Installa2. UO I jo o Zo9yssad yo uoJojiuow 000 UO I Jo o Soy 5594 yo uo s zzng uo I Ho uo Ho o 09 Ssaid Sunusi punol5yoeg ulese Mau s luq 5181 9 po Mau Jajuj Zey SSald PJOMSSEd a8UEUJ z 40 t o ind oun SUIUJEM no Ae 2J 66 10 spuodas zy SSAJ play 100p asuey z Jo 1 o ind no 66 10 spuodas gey ss lq lin Suluado S dais Y dais das z das t das uoloun4 9 Ssaid 11x3 piomssed au Suuaqua pue g Suissaid Aq eys SAPM V K44 Duo Installation 8 User manual 26 ulese ong QQIZIL SSald 991211 SSAld TMS 559 4 Dia uado Mowaw 5 z 40 170 UO I 1ndjno Aejoi Ja uj yo 0 Tgy Seaid yo uo uomuny 21880 UO I Jo ol ogy ss ld Ho uo Aejaq HO Hae uo SS mp I o ssainp uo yaje 694 5594 ss mnq H ly S dais Y das dais z dais 1 dels uon un K44 Duo Installations 8 Anv ndarhandbok 27 Copyright 2006 Bewator AB Solna Kopiering ur denna handbok far ske endast efter skriftlig verenskommelse med Bewator Bewator f rbehaller sig ratten att andra saval handbokens innehall som produkternas konstruktion JAS Dokumentnummer 80718 6 Bewator AB utvecklar och marknadsf r ett komplett utbud av s kerhetspro dukter vilket inkluderar passerkontroll och larm F rs ljning installation och service sk ts via ett rikst ckande n t av terf rs ljare
3. Door monitoring on off Set door held warning time Delay on off Erase the memory Using K44 Duo Entrance Unlock the door permanently Enter duress code Technical data 23 K44 Duo Installation 8 User manual 5 What is K44 Duo K44 Duo is a compact code lock with two relay outputs This makes K44 Duo capable of controlling two doors or one door and an optional function e g a light switch Either a four or a six digit code can be used to open connected doors All programming is done from the keypad Open two doors using one code The advantage of using two relay outputs is that two func tions can be activated at the same time using only one code For example the code can open the lock and turn on a light switch at the same time Another setup is to connect the code lock to two doors One code is programmed to operate both doors while the other only opens one of the doors If the code is programmed to open both doors you can set K44 Duo so that the other door does not open until the first door has been opened and closed see the Delay section For each code choose whether to activate both relay outputs only one or only the other Disable the codes whenever needed K44 Duo offers the possibility to disable codes at certain times For example the cleaning staff s access to the build ing can be limited to certain hours while tenants staff
4. tg rder s som olovlig manipulering olovlig kopiering m m f r inte vidtas med i produkterna och systemen ing ende programvara S dana tg rder utg r upphovsr ttsintr ng som kan bestraffas med b ter eller f ngelse och resultera i skyldighet att betala skadest nd och vederlag f r utnyttjandet av programvaran
5. Enter 3 Choose vhat relay outputs the toggle function should apply to both 1 relay output 1 2 relay output 2 To deactivate the toggle function follow the above steps only enter o in step 2 instead In the Unlock the door permanently section you will find instructions on how to unlock the door perma nently K44 Duo Installation 8 User manual 17 Duress or Alert The K44 Duo allows for either using duress or alert The same command is used for different function Duress With the Duress function activated a user can enter a special code if he or she is forced to open the door under threat It is important to have a plan for what action to take when a duress code is entered NOTE If Duress is activated make sure you have not programmed codes with consecutive digits Code 1234 must not exist with codes 1235 and 1233 Code 5679 must not exist with codes 5670 and 5678 The Enter duress code section describes how a user should enter the duress code Alert When K44 Duo is delivered the alarm output is set to be activated if the door is open too long or if the door is forced open Note that door contacts must be connected and that Door monitoring must be activated for this to work 18 K44 Duo Installation 8 User manual This is how to choose one ofthe functions 1 Enter A69 2 Enter either o Door Alert default 1 Duress Door monitoring on off If door contacts are used and this function is a
6. be opened Note that door contacts must be connected and that Door control must be activated for this to work This is how to activate Delay 1 Enter 2 Enter To deactivate Delay press o in step 2 instead Erase the memory This is how to erase all programmed information including the password 1 Press B and enter the current password 2 Press SW1 on K44 Duo s circuit board 3 Enter 112186 4 Enter 112186 once again The memory is now erased and K44 Duo goes back to the factory settings K44 Duo Installation 8 User manual 21 Using K44 Duo 2 Entrance To open the lock a 4 digit or 6 digit code should be entered on the code lock s keypad K44 Duo is blocked if a visitor performs 12 keypress es without finding the correct code To release the blockage enter a correct code twice in succession Unlock the door permanently To unlock the door permanently proceed as follows 1 PressB 2 Enter the entrance code 3 Enter The door is now unlocked green LED is lit To lock the door follow the above steps only enter o in step 3 instead 22 K44 Duo Installation 8 User manual Enter duress code This is how to activate the alarm output when forced to open the door under threat Enter the usual entrance code only add 1to the last digit in the code Example 1 If the entrance code is 1234 enter 1235 instead Example 2 If the code is 1239 enter 1230 instead When a duress code is entered th
7. Pray gt gt gt K44 Duo Installation amp User Manual POPDPEOO A BEWATOR Siemens Business Book Contents AU aaa 3 SVENSKA AP 27 K44 Duo Installation 8 User manual 3 English Copyright O 2006 Bewator AB Solna Material from this manual may only be copied with the consent in writing of Bewator Bewator reserves the right to alter both the content of the manual and the design ofthe product Document number 80718 6 Bewator AB develops and markets a complete security product range that includes access control and alarm Sales installation and servicing are handled by a national dealer network Actions such as unauthorised manipulation copying etc must not be taken with the software contained in the products and systems Such actions are regarded as copyright violation and may result in imprisonment or fines and may likewise lead to an obligation to pay damages and compensation for using the software 4 K44 Duo Installation 8 User manual Contents What is K44 Duo Duress or alert Zero opening Unlock the door permanentl Door bell Programming Buzzer and LEDs Choose password edi Change password 11 Programming commands 11 Program codes Erase codes Change codes Set opening time Background lighting on off Toggle function on off Duress or Alert
8. can have access to the door 24 hours a day By connecting two time clocks to K44 Duo three different time zones can be used to control the codes one controlled by time clock 1 one controlled by time clock 2 and one that is valid 24 hours a day i e no time control 6 K44 Duo Installation 8 User manual Duress or alert K44 Duo is eguipped with an output that can be activated for one ofthe following reasons e Auserenters a duress code OR e The door held warning time expires or the door is forced open Choose which alternative to use Then connect e g a bur glar alarm or similar to the output Zero opening To make entrance easier e g during office hours connect an external contact Then use the contact to activate or deactivate zero opening i e opening the door by pressing the zero button on the keypad Note that this is only applies to relay output 1 Unlock the door permanently If the Toggle function is activated the code can be used to unlock the door The door remains open until a valid code is entered once again see the Toggle on off section Door bell If needed a door bell can be connected to K44 Duo To ring the bell the visitor presses the button labelled with a bell on the code lock s keypad K44 Duo Installation 8 User manual 7 The keypad Red LED Yell LED G LED ellovv reen For optional indicates Lit when use 8 keypresses the dooris to indicate unlocked alarm on
9. ctivat ed a warning signal sounds during the time set as door held warning time i e when the opening time has expired and the door is still open If the door held warning time expires and the door is still open the alert output is activated if the Alert function is activated This also happens if the door is forced open This is how to activate Door monitoring 1 Enter A67 2 Enter To deactivate Door monitoring press 0 in step 2 instead K44 Duo Installation 8 User manual 19 If the door is still open when the opening time has expired a buzzer sounds as to remind the visitor to close the door immediately or the alarm output will be activated The buzzer sounds until the door is closed Note that door contacts must be connected and that Door control must be activated for this to work This is how to change the door held warning time if needed 1 Enter Azg 2 Enter the desired door held warning time 01 99 with two digits e g 09 for 9 seconds 3 Choose to which relay outputs the new door held warning time should apply o both 1 relay output 1 2 relay output 2 Set door held warning time E 20 K44 Duo Installation 8 User manual Delay on off When this function is activated the following hap pens If a code is programmed to open two doors lock relay 2 is not activated until door 1 has been opened and closed If door 2 is opened with the exit button door 2 has to be opened and closed before door 1 can
10. e door will open at the same time as the duress output is activated It will remain activated until reset by somebody enter ing programming mode K44 Duo Installation 8 User manual 23 Technical data 2 Power supply 8 24 VAC 10 35 V DC Power consump 75 MA tion Maximum load over 2 28 V DC the relay contacts Dimensions 140X80X40 HxWxD mm Suitable height 1200 1400 mm from ground to bottom edge If needed complete the installation with flush mounting kit BB3 K44 Duo Installation 8 User manual 24 apo 00 zzy aoueajua JAOge 335 o SSaid o ss ld 0000 396 ss ld 95213 poul Sulul z e z z dno 3 z We1801d 01 00 1 Aejal I tdnog 1 g SSaid 1122 uloq auou Y po Ja U apo dats wo paa ndino 8 IM poo 2p02 1181p Y zzy a uesuo Old 2p02 YAN Aejaa 1 maujajuj po2 p o 194347 ss lq v apow E SuruweiSoid z Aejal 2 z dno18 z Sapo o ypeq g ssaig 1 AE T 1 dnojs 1 181 9 06 12 2 xa te days uloq auou SUOI E90 apo E LOJJ P32201d ndino dno 3 su8ip 940 51181 2 101 Tey ubnu E 1 p02 3X N Aey l Jaju3 1 19 u3 7 po 20 po ss ld N N 5 uon un 9 Ssaid 1x piomssed y Suuaqua pue g Suissaid q 11515 SAPM V 25 K44 Duo Installation 8 User manual
11. er the new code once again 5 Choose whether or not the code should be disa bled from a time clock o no time control 1 code disabled from time clock 1 2 code disabled from time clock 2 6 Choose which relay output to control o both relay outputs 1 relay output 1 2 relay output 2 7 Change the next code by continuing from step 2 or press B to leave code program A vu K44 Duo Installation 8 User manual 15 Set opening time The opening time determines for how long the lock should remain open following a correct entrance code When K44 Duo is delivered the openingtime is 7 seconds for both relays 1 Enter A28 2 Enter the desired opening time 01 99 using two digits e g 09 for 9 seconds 3 Choose which relay output the new opening time applies to both 1 relay output 1 2 relay output 2 Background lighting on off This is how to turn off the keypad s background light ing ifneeded 1 Enter 2 Enter To reactivate background lighting press 1 in step 2 instead 16 K44 Duo Installation 8 User manual Buzzer on off This is how to deactivate the buzzer if sound on key presses and door opening is not desired Note that the buzzer will keep sounding during programming 1 Enter A65 2 Enter o To reactivate the buzzer press 1 in step 2 instead Toggle function on off To be able to unlock a door permanently the toggle function has to be activated Proceed as follovvs 1 Enter A81 2
12. the back of the manual Programming commands Always press B and the password before any com mands are used Leaving the programming mode can be done by pressing B 12 K44 Duo Installation 8 User manual Program codes Enter A21 2 Enter the desired code location using two digits 01 30 3 Enter the code for the current code location four digits for code location 01 20 or six digits for code location 21 30 Note The four first digits in a 6 digit code must not be the same as the digits in a 4 digit code and the other way around 4 Choose whether or not the code should be disa bled from a time clock o notime control 1 code disabled from time clock 1 2 code disabled from time clock 2 5 Choose which relay output to control o both relay outputs 1 relay output 1 2 relay output 2 6 Program the next code by continuing from step 2 or press B to exit K44 Duo Installation 8 User manual 13 Erase codes 1 Enter A22 2 2 Enter the current code If it is a 4 digit code enter A after the last digit If it is a 4 digit code enter 0000 If it is a 6 digit code enter 000000 Enter 0000 000000 again Enter o Enter o once again Erase the next code by continuing from step 2 or press B to exit NUI BW 14 K44 Duo Installation 8 User manual Change codes 1 Enter A22 2 Enter the current code If it is a 4 digit code enter after the last digit Enter the new code using four or six digits Ent
13. tion 8 User manual Programming Before you start programming K44 Duo make a note ofthe codes to be used to what timing group they should belong and which relay output they should control At the back of this manual you will find a chart designed for this purpose Look at the chart as you program K44 Duo according to the instructions below Buzzer and LEDs During programming you will be guided by the buzzer and the LEDs In programming mode before a function is chosen Green and yellow LED flashes During programming Yellow LED goes out Green LED is lit Correct instruction Confirmed by a rising signal consisting of two quick beeps Faulty instruction Confirmed by a falling signal consisting of two quick beeps NOTE During programming mode if a button is not pressed within 20 seconds the code lock goes back to normal operation K44 Duo Installation 8 User manual 11 The first thing to do before you can start program ming is to choose a password 1 Press and hold the SW1 button on the code lock s circuit board Both LEDs are lit 2 Enter a 6 digit password 3 Make a note of the new password in the chart at the back of the manual Choose password B Change password 1 Press B and enter the current password 2 Enter A27 3 Enter the new password A warning tone is heard 4 Enter the new password once again 5 Press B to leave programming mode 6 Make a note of the new password in the chart at
Download Pdf Manuals
Related Search