AMG1000BOx-VCM
Contents
1. GSM Main CDMA GPS Cellular Connector Cellular Antenna Antenna Antenna Connector Connector Connector Figure 6 AMG Base Unit Connectors 4 2 Wiring Harness for OBDII based Vehicles which are Model Year 2008 and newer The wiring harness for OBDII vehicles is shown in Figure 7 It is one assembly that connects the AMG to the vehicle s OBDII port provided by the vehicle manufacturer It also provides a lead wire that needs to be routed to a vehicle electrical source that is powered when the vehicle ignition is on and unpowered when the vehicle ignition is off This vehicle ignition sensing connection is usually made at the fuse box using the supplied add a circuit device AMG1000BOx VCM OBDII Vehicle Kit Installation Guide FLEETLYNX Figure 7 Wiring Harness for OBDII Vehicles Wiring Harness Installation Overview Figure 8 shows the wiring harness installation overview The following section provides the detailed installation instructions The general concept is to plug the 8 pin molex connector into the AMG and the D shaped 16 pin connector into the vehicle s OBDII port Lastly the ignition sense wire gets connected to the fuse panel Optionally if the OBDII Y Cable option is being used it is installed between the vehicle s OBDII port and the OBDII connector of the wiring harness AMG1000BOx VCM OBDII Vehicle Kit Installation Guide FLEETLYNX AMG10220BDY Y Splitter Cable This cable is OPTIONAL AMG102202. V6 chm a n c e r k s L ETLYNX Advanced Mobile Gateway AMG1000 OBDII Vehicle Kit Installation Guide AMG1000BOx VCM 1 0 Safety amp Regulatory Information Important safety and regulatory information on the AMG unit may be found on page 14 of this installation guide A CAUTION Be sure to thoroughly review the safety and regulatory information before installing and activating the AMG unit A WARNING This kit should only be installed in vehicles 2008 or newer DO NOT attempt installation in vehicles manufactured in and prior to 2007 A non OBDII wiring harness unit can be installed on 2007 and older vehicles connections to older model OBDII interfaces are not supported and can cause damage to the vehicle 2 0 Kit Contents A WARNI NG if the vehicle is 2007 or older this kit should be returned and an L kit should be used in its place There are four AMG aftermarket kits available for installation in light duty or passenger type vehicles whose on board vehicle data protocol is OBDII Two of the kits do not connect to the vehicle s OBDII data port at all and so can be put into any such vehicle regardless of its model year These two non OBDII connection kits differ only in the antenna selection In contrast the other two kits including this one require a connection to the vehicle s OBDII data port However this product is only compatible with the newer OBDII physical interface called the CAN bus In North
3. e Connect the OBDII harness to the vehicle s OBDII connector e Verify that the GPS and PWR LEDs are flashing green The CELL LED will be solid amber until the unit has established a connection with the cellular provider This may take a few hours following your request for activation The CELL LED must be flashing GREEN before the unit is installed in your vehicle AMG1000BOx VCM OBDII Vehicle Kit Installation Guide FLEETLYNX 3 3 Planning the AMG Location A WARNING The AMG unit should be installed and secured in a dry location Installation in a location where it may be easily accessed by water and other liquids ie directly under windshied seams AC lines cupholders etc is not recommended If the AMG is exposed to any amount of any sort of liquid internal corrosion will occur and the AMG will eventually cease to operate Damage due to liquid intrusion is not covered by warranty Identify the best location for installation Before the wiring harness AMG base unit and antenna are installed it is strongly recommended that the vehicle is inspected for potential installation locations and an installation plan is devised Keep the following information in mind when locating a suitable install location and plan 1 The AMG base unit may not be installed any further than 9 feet away from the vehicle s interior fuse panel 2 The AMG base unit may not be installed any further than 9 feet away from the manufacturer s OBDII connector wh
4. optional Crimp Tool to attach add a circuit fuse accessory Zipties to secure loose wiring and perhaps the AMG itself 3 2 Activation Before Vehicle Installation Step 1 Preparation Please download and review the Installation and Activation Form as well as the Quick Start Guide They are found at http www fleetlynx net mnl Step 2 Collect information Collect the following information for each FleetLynx unit and fill out these fields in your I nstallation and Activation Form AMG Serial Number see Figure 2 for location of this information Fleet Name the name of the fleet the vehicle belongs to Vehicle Number the number the fleet uses to identify the vehicle Dealer Code the code for the dealership where the FleetLynx unit was purchased from VIN the Vehicle Identification Number for the vehicle in which the AMG unit will be installed Odometer the vehicle odometer reading from the dash AMG1000BOx VCM OBDII Vehicle Kit Installation Guide 3 FLEETLYNX e Company Name vehicle owner e Installation Contact Name e Installation Contact Phone and email AMG Serial Number BER Please call Veuillez appeler to activate 877 955 3122 pour activer It is important that the UNIT S N is Il est important que le num ro de s rie associated with the Truck that de cet appareil soit associ au num ro will receive this un
5. Wiring Harness Installation Steps 1 Locate the vehicle s interior fuse panel refer to vehicle user manual 2 Determine the best location to mount the AMG as detailed in Section 3 0 with the stipulation that the AMG base unit must be no further than 9 feet from the vehicle s interior fuse panel 3 Disconnect the vehicle s negative battery terminal 4 Connect the I gnition Sensor IGN SEN brown wire on the AMG wiring harness to the add a circuit fuse holder J HFUSE 14 included in the kit using the pre installed butt connector and an appropriate crimp tool as shown in Figure 9 Connect the IGN SEN brown wire on the AMG wiring harness Crimp the wire into the pre installed butt connector using an appropriate crimp E EE tool L d w a mm mm A 9 Figure 9 Connect IGN SEN Brown Wire to Add a Circuit Device 5 Remove the fuse and install the add a circuit into the switched 12V fuse position found in step 4 The fuse removed from the panel should be installed into the add a circuit in the lower position 10A or less ONLY and the 3A fuse included in the kit should be installed in the upper position opposite the wire and crimp as shown in Figure 10 The 3A fuse included d in the kit should be installed in db the upper position opposite qn p the wire and crimp _ w v i The fuse removed from the panel should be instal
6. cable can be used for an alternate mounting point The remaining free end of the Y splitter cable is to be connected to the OBDII connector of the main wiring harness as shown in Figure 8 Use cable restraining ties or other technique to secure the cables in a safe and recessed location 5 0 Mounting the Unit Once the AMG is connected to the Molex 8 pin connector as well as the OBDII connector the AMG base unit may be secured to the vehicle An AMG is properly secured when t cannot be easily moved or jostled around e The backpack antenna remains horizontal with a clear line of sight to the sky The backpack antenna needs to be secured also if it has been unscrewed from the AMG e The 4 lights on the AMG are visible to the installer so that proper operation of the AMG may be confirmed e No wires are loose or unsecured Securing the unit using Screws preferred The unit may be secured to the vehicle using two 8 Pan Head Screws with a maximum head diameter of 0 325 The recommended maximum torque is 6 0 in lbs If holes are to be pre drilled space them 6 inches apart as shown in Figure 11 AMGI000BOx VCM OBDII Vehicle Kit Installation Guide 11 FLEETLYNX 8 Pan Head Screw Head diameter 0 325 max Maximum torque 6 0 in Ibs nr eh iy er ee as th BS ah Eh i ITEM a Area of the vehicle to anchor AMG unit Head d
7. the AMG serial number VCM AMG lt Serial gt Click on the name then click connect Instructions for connecting to a wireless network will vary for other operating systems Step 3 When prompted enter the security key 55555 Step 4 Using a web browser navigate to the AMG Diagnostics page http 10 10 0 1 Note The Diagnostics page does not auto update Refresh the page to get an updated diagnostics view Step 5 Review the AMG Diagnostic page details as indicated in Figure 15 AMG1000BOx VCM OBDII Vehicle Kit Installation Guide FLEETLYNX AMG Diagnostics Information Serial Number 35990342 Battery Voltage 11 9 Volts CSM Modem Status Hetwork Name ROGERS Service Provider ROGERS Signal Strength 61 dBm 5 5 Bars 100 5 Provisioned Yes Registered Yes Roaming Na Antenna status OF Connection Connected to internet CDMA Modem Status Network Name 16410 Service Provider Telus Signal Strength 51 dBm 5 5 Bars 100 5 Provisioned Yes Registered Roaming Na Antenna status OF Connection Ho internet connection Signal D fix Yes 3D fix Yes HOOP 31 poor Satellite count 5 Antenna status OF No CAN Bus J1935 OBDII Parking Brake Parking Brake Source Ignition Sense AMG Temperature 41 1 Celsius 106 0 Fahrenheit AMG Orientation Figure 14 AMG Diagnostic Webpage AMG1000BOx VCM OBDII Vehicle Kit Installation Guide 17 FLEETLYNX 18 AMG Diagnostics Information Ensure
8. to people or makes the equipment unsafe A CAUTION To comply with Industry Canada RF exposure requirements a minimum separation distance of 8 inches 20 centimeters is required between this antenna and all persons Pour conformer aux conditions d exposition RF d Industry Canada une distance minimum de s paration de 20 centimetres est exig e entre l antenne et toutes personnes Regulatory Notices Federal Communications Commission FCC Compliance This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions e This device may not cause harmful interference and e This device must accept any interference received including interference that may cause undesired operation This equipment complies with FCC radiation exposure limits set forth for an occupational controlled environment The antenna s used for this transmitter must be installed to provide a separation distance of at least 8 20cm from all persons and must not be co located or operating in conjunction with any other antenna or transmitter This transmitter is approved for use with the antennas supplied with this equipment Maximum Antenna gains including cable loss are AMG1021B Backpack Antenna 1 6dBi GSM 850 and 2 9dBi PCS1900 AMG1021A External Antenna 1 0dBi GSM 850 and 1 7dBi PCS1900 Use of different antennas is not permitted Failure to comply will invalidate FCC rule compliance A WARNING Cha
9. America compatible vehicles include all those from model year 2008 and newer These two OBDII connection kits differ only in the antenna selection Note as well that for each of the four kits there are both Canadian and US variants In total there are eight unique installation kit numbers There are no installation differences between the Canadian and US variants so this one document is used to describe both e AMG1000BOx VCM kits include the Backpack Antenna and will be used in the majority of cases where both the base unit and the antenna are to be installed in the vehicle interior This kit is for the OBDII CAN based interface that is found in model year 2008 and newer vehicles This is the installation guide for the AMG1000BOx VCM kit as shown in Figure 1 AMG1000BOx VCM OBDII Vehicle Kit Installation Guide 1 rol FLEETLYNX AMG1000BOx VCM kit contents AMG1020 x AMG10220BDY Advanced Mobile Gateway Backpack Antenna OBDII to AMG Cable OBD Y Cable Optional where x U if equipment is to be operated in the USA x C if equipment is to be operated in Canada Figure 1 AMG1000BOx VCM OBDII Vehicle Kit For reference the other three installation kit documents are available at http www fleetlynx net mnl The other 3 installation kit numbers are as follows e AMG1000AOx VCM kits include the External Antenna and should be used when it is necessary to install the antenna on the cab exterior or if specifically
10. Code of Federal Regulations Title 47 part 90 section 90 20 Public Safety Pool LAW AND VENUE The validity and interpretation of these terms shall be governed by the laws of the Province of British Columbia and Canada and any such dispute shall be submitted exclusively to the British Columbia courts The parties agree that any conflicts of laws provisions where applicable are hereby excluded by this express agreement to attorn to the specified law and venue PERMISSION TO REPRODUCE Except as otherwise specifically noted the information in this publication may be reproduced in part or in whole and by any means without charge or further permission from Vecima Networks Inc provided that due diligence is exercised in ensuring the accuracy of the information reproduced that Vecima Networks Inc is identified as the source and that the reproduction is not represented as an official version of the information reproduced WARRANTY Vecima Networks Inc provides this guide without warranty of any kind either implied or expressed including but not limited to the implied warranties of merchantability and fitness for a particular purpose Any representation s in this document concerning performance of Vecima Networks product s are for informational purposes only and are not warranties of future performance either express or implied Vecima Networks Inc reserves the right to revise this publication and to make changes in content from time to ti
11. L ETLYNX 7 0 Confirm AMG Operation AMG operation status is best confirmed by viewing the AMG Diagnostics Page from a Wifi enabled device However in the case where a Wifi enabled device is not available AMG operational status will have to be confirmed by viewing the AMG LED status lights 7 1 Confirming AMG Operation with Status Lights Note This procedure is not necessary if AMG operation has already been confirmed by viewing the AMG Diagnostics page AMG operational status can be confirmed via the four AMG LED Status Lights The AMG LED Status Lights are located on the side of the AMG base unit Procedure Step 1 Start the vehicle and wait at least 90 seconds to allow the AGM to acheive a steady operational state PWR CELL and DATA lights should begin to maintain a green and blinking status within 90 seconds the GPS LED may need a few minutes longer Step 2 Confirm that all four lights on the AMG are green and blinking e Ifthe DATA light is not green and blinking confirm the connection to the OBDII databus is completed as described in this guide e If GPS or CELL light is not green and blinking i e unblinking amber and the vehicle is in a service bay drive the vehicle outside with a clear line of sight to the sky If the vehicle is already outside check the position of the backpack antenna making sure it is parallel to the ground and not obstructed by any metal objects e Ifthe PWR light is not gre
12. M OBDII Vehicle Kit Installation Guide 19 9 0 20 Pp gt gt gt bb FLEETLYNX Safety amp Regulatory Information Document Conventions This document uses the following special formats to emphasize key information Be aware of all warnings and cautions before you begin to use AMG1000BOx VCM WARNING Whenever you see this icon and heading the associated text addresses or discusses a critical safety or regulatory issue CAUTION Whenever you see this icon and heading the associated text discusses an issue which could result in damage or abuse of the equipment Carefully read and follow these instructions Safety Precautions Read and follow the following safety instructions before installing or operating an AMG1000BOx VCM kit WARNING Before installing or operating this equipment read all safety installation and operating sections Follow all instructions failure to do so may result in damage to the unit or severe personal Injury Retain this manual for future reference Avant d installer ou d op rer cet quipement lisez toutes les sections de s curit s d installations et d op rations Gardez ce manuel comme source de r f rence Suivez toutes instructions si non vous risquez d endommager la machine ou de vous blesser s rieusement WARNI NG servicing should not be attempted by the user There are no user serviceable parts inside Refer all servicing to factory qualified personnel N essayez p
13. OBDP2 can also be connected directly to the vehicle s dashboard OBDII connector Vehicle Dashboard w eee eee m mm um wm m mm momo wo umo mo mo Rmo mo momo mo mo o m EG OBDII Connector AMG10220BD2 VEHICLE FUSE PANEL OBDII to AMG Cable Add a Circuit JHFUSE 14 Attach GND wire to a good chassis ground point inside the vehicle These can usually be found near the fuse panel and or stereo Connect the Ignition Sensor wire to a spare fuse position which has a switched 12V only live with ignition and accessory via an add a circuit device or by direct splice including a 3A inline fuse if there is not enough clearance for the add a circuit device GND Black IGN SEN Brown DIG IN1 Violet OWDAT Blue Molex MiniFit Connector 5 OWDAT PR ee um um m mm um mm um Gm Gm Gm um Gm um Gm Gm nm ee mo Rmo ee mo Rmo Gm Rmo Gm Rmo ee Gt Rmo eee Rmo m ee ee mo m eee eee ee oum wm oum m wm m mj m omo mom 6 CAN_L Plugs into AMG base unit 7 CAN_H These wires on the harness 8 VBATT are not used The ends can be taped together and tucked out of the way AMG base unit Connector Side Figure 8 Wiring Harness Installation Overview AMG1000BOx VCM OBDII Vehicle Kit Installation Guide 10 4 3 FLEETLYNX
14. as de r parer cet quipement vous m me R f rez toutes revisions n cessaire au personnel qualifi de la manufacture WARNING Cleaning Do not use liquid or aerosol cleaners Use a damp cloth for cleaning Le nettoyage n utilisez pas de nettoyeurs a rosols ou liquides Utilisez un tissu humide pour nettoyer WARNING Electrostatic discharge ESD can damage equipment and impair electrical circuitry ESD damage occurs when electronic components are improperly handled and can result in complete or intermittent failures Always follow ESD prevention procedures when you are working on an AMG base unit or antenna Ensure that the unit is electrically connected to an earth ground and wear a properly grounded ESD preventive wrist strap If no wrist strap is available ground yourself by touching the metal part of the unit WARNING The installation of your AMG device must comply with vehicle wiring standards and best practices WARNING Fuse handling equipment must be used to remove or install fuses and shunts when the terminals are energized The tool must be insulated for the circuit voltage WARNING Disconnect all power before installing or removing a chassis Never assume that power is disconnected from a circuit Always check Note Keep the chassis area clear and dust free during and after installation AMG1000BOx VCM OBDII Vehicle Kit Installation Guide FLEETLYNX Note Do not perform any action that creates a potential hazard
15. en and blinking i e all lights are off or PWR is unblinking red please recheck the power cables and connectors e Check all three antenna connections CDMA GSM and GPS to make sure the connectors are well seated and the antenna leads are mated to the correct connection posts If all four AMG status lights are not green and blinking please call 1 877 955 3122 for installation assistance Once all of the required status lights have been visually confirmed re install the dashboard 7 2 Confirming AMG Operation with the AMG Diagnostics Page The AMG Diagnostics page provides a detailed summary of the AMG s operational status this page is accessible using a Wifi enabled PC laptop tablet or smartphone 7 2 1 Connecting to the Diagnostics Web Page Prerequisites e Wifi enabled PC laptop tablet or smartphone AMG1000BOx VCM OBDII Vehicle Kit Installation Guide 15 FLEETLYNX e The device s Wifi radio must run in ad hoc mode to match the AMG s Wifi ad hoc mode e AMG serial number of the unit to be checked must be known Procedure Step 1 Start the vehicle and wait at least 90 seconds to allow the AGM unit to acheive a steady operational state Step 2 Connect the Wifi enabled device to the AMG ad hoc wireless network For Windows In Control Panel gt Network and Internet click on Connect to a network under the Network and Sharing Center heading In the Wireless Network Connection window find the network name with
16. iameter 0 325 max Maximum torque 6 0 in Ibs 6 00 6 80 Figure 11 Securing the AMG base unit using Screws AMG1000BOx VCM OBDII Vehicle Kit Installation Guide FLEETLYNX Securing the unit using Zip Ties The unit may be secured to the vehicle using two zip ties as shown in Figure 12 Note that the zip ties should be positioned inside the zip tie fences on the AMG base unit enclosure Zip Tie fences prevent the zip ties from slipping off side X je mine si ee N Area of the vehicle to Mn Position Zip Tie on inner anchor AMG unit pU side of fence Figure 12 Securing the AMG base unit using Zip Ties AMG1000BOx VCM OBDII Vehicle Kit Installation Guide FLEETLYNX 6 0 Mounting the Antenna The backpack antenna may be mounted directly on the AMG base unit once the base unit is secured to the vehicle Alternatively if desired the backpack antenna may be mounted up to 3 feet away from the AMG base unit using two 6 or M3 5 Pan Head Screws with a maximum head diameter of 0 275 The recommended maximum torque is 5 0 in lbs If holes are to be pre drilled space them 3 inches apart as shown in Figure 13 6 or M3 5 Pan Head Screw Head diameter 0 275 max Maximum torque 5 0 in Ibs 4 47 Figure 13 Backpack Antenna Mounting Holes 14 AMG1000BOx VCM OBDII Vehicle Kit Installation Guide F
17. ich is usually found under the dash near the steering column 3 Is not visible to the driver during normal vehicle operation to eliminate driver distraction 4 Will allow the technician to be able to see all four LEDs on the unit 5 Allows easy access to the GPS CDMA and GSM connections on the unit 6 Enables the AMG base unit to be secured properly using the chosen method AMG base unit mounting cab interior LS AMG BASE UNIT 3 ORIENTATION Ew CRITICAL The mounting he mounting location location should should provide access allow the status to the cable connections LEDs to be on the AMG base unit visible to the installer Figure 3 Optimal Unit Orientation 3 4 Planning the Antenna Location Identify the best location for installation Before the wiring harness AMG base unit and antenna are installed it is strongly recommended that the vehicle is inspected for potential installation locations and an installation plan is devised Keep the following information in mind when locating a suitable install location and plan 1 The backpack antenna may be installed either on the AMG base unit or independently up to 3 feet away 2 Antenna reception is critical for effective AMG operation therefore the antenna must not be obstructed by metal objects Optimal antenna orientation is shown in Figure 4 and Figure 5 AMG1000BOx VCM OBDII Vehicle Kit Installation Guide 5 FLEETLYNX Has clear line of sight to the
18. ise Vecima Networks Inc shall also not be liable if the installation and or use of the product voids any other warranty which the buyer installer and or any third party benefits from including but not limited to vehicle manufacturer warranties The buyer installer or any third party s s total recovery from Vecima Networks Inc shall not exceed the price the buyer has paid for the specific unit of product giving rise to the claim USE IN CRITICAL MEDICAL SYSTEMS PROHIBITED PRODUCTS SOLD BY VECIMA ARE NOT DESIGNED INTENDED OR AUTHORIZED FOR USE IN LIFE SUPPORT LIFE SUSTAINING NUCLEAR OR OTHER APPLICATIONS IN WHICH THE FAILURE OF SUCH PRODUCTS COULD REASONABLY BE EXPECTED TO RESULT IN PERSONAL INJURY LOSS OF LIFE OR CATASTROPHIC PROPERTY DAMAGE IF BUYER USES OR SELLS THE PRODUCTS FOR USE IN ANY SUCH APPLICATIONS 1 BUYER ACKNOWLEDGES THAT SUCH USE OR SALE IS AT BUYER S SOLE RISK 2 BUYER AGREES THAT VECIMA IS NOT LIABLE IN WHOLE OR IN PART FOR ANY CLAIM OR DAMAGE ARISING FROM SUCH USE AND 3 BUYER AGREES TO INDEMNIFY DEFEND AND HOLD VECIMA HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS DAMAGES LOSSES COSTS EXPENSES AND LIABILITIES ARISING OUT OF OR IN CONNECTION WITH SUCH USE OR SALE Furthermore this device AMG1020 may cause interference to other radio devices operating in the frequency band 155 1525MHz to 155 1825MHz this frequency band is typically used by 2 way radio devices licensed for use in accordance with United States
19. it du camion qui recevra cet appareil Y FL amp ETLYNX a UNIT S N 1234567890 I TANN P N AMG1020U WN NT P N AMG1020U BAUER S AMG Bar Code Label Close Up Bottom of AMG Unit Figure 2 AMG Serial Number Step 3 Activation Contact FleetLynx support to activate your unit once the information from Step 2 is obtained A customer service agent will then activate the unit It will usually take a few minutes to complete You may also send us a partially completed Installation and Activation Form Phone 1 877 955 3122 Fax 1 306 657 3177 Email amgsupport vecima com If you are a new customer please provide the New Customer Application and FleetLynx Service Agreement Step 4 Pre Install Verification Recommended Preactivate and verify that your FleetLynx unit is operating properly prior to final installation in the vehicle Note Installer can use the OBDII interface from the vehicle to power up the unit All other vehicle connections are not necessary at this point however this step could take a number of hours to complete The AMG unit will need to be outside in order to confirm the GPS status and possibly the mobile coverage depending on the type of building in which the installed unit may be working However unless there is ignition or vehicle data being observed the AMG will shut off after an hour With a quick plug connection it may be necessary to unplug replug hourly until CELL flashes green
20. led into the add a circuit in the lower position 10A or less ONLY Figure 10 4 Add a Circuit Device Fuse Insertion 6 Attach GND wire to a good chassis ground point inside the vehicle These can usually be found near the fuse panel and or stereo 7 The remaining wires on the harness are not used The ends should be taped together to eliminate the chance of an unwanted connection being made and then tucked out of the Way 8 Plug the Molex 8 pin connector into the AMG 9 Re connect the negative battery cable AMG1000BOx VCM OBDII Vehicle Kit Installation Guide FLEETLYNX 4 4 Optional Y cable Installation The optional Y cable is intended to provide a convert connection to the vehicle s OBDII port As well it keeps the AMG s cable attachment away from the driver s legs and thus the connection becomes more reliable under normal vehicle operations The Y cable is ordered separately 1 2 3 4 5 6 If necessary open the vehicle dashboard panel to gain access to dashboard wiring Remove the vehicle s current OBDII connector port from the panel bulkhead Connect the male connector of the Y splitter cable to the vehicle OBDII connector Insert one of the female ends of the Y splitter cable back into the panel location from where the vehicle s original OBDII connector was removed It does not matter which of the two female connector ends is used The optional mounting bracket included with the Y splitter
21. mal et l imp dance requise pour chaque type d antenne Les types d antenne non inclus dans cette liste ou dont le gain est sup rieur au gain maximal indiqu sont strictement interdits pour l exploitation de l metteur AMG1021B Backpack Antenna Impedance 50 Ohm Nom Maximum Gain including cable loss 1 0dBi GSM 850 and 1 7dBi PCS1900 AMG1021A External Antenna Impedance 50 Ohm Nom Maximum Gain including cable loss 1 6dBi GSM 850 and 2 9dBi PCS1900 AMG1000BOx VCM OBDII Vehicle Kit Installation Guide FLEETLYNX INSTALLATION STANDARD The buyer and or installer agrees that it is fully experienced and properly qualified to perform the installation work provided for herein and that it is properly licensed equipped organized and financed to perform such work The buyer and or installer will perform all installation work in accordance with its own methods on a best efforts basis subject to compliance with the instructions set out herein and in accordance with generally accepted professional standards Failure to do so will render the Vecima Network s Inc warranty null and void to the maximum extent allowed under applicable law LIMITED LIABILITY Vecima Networks Inc shall not be liable to the buyer installer or any third party for any indirect or consequential loss or damages including without limitation loss of business or profits whether arising under any indemnity or from negligence breach of contract or otherw
22. me without obligation on the part of Vecima Networks Inc to provide notification of such revision or change Vecima Networks Inc 150 Cardinal Place Saskatoon SK Canada S7L 6H8 Published in Canada Specifications subject to change without notice AMG1000BOx VCM OBDII Vehicle Kit Installation Guide 23 24 FLEETLYNX Third Party Software License Agreement License agreement information for third party software utilized in the FleetLynx AMG unit may be obtained from the document located at http www fleetlynx net PDF amg_ thirdpartynotification ml r03 sd pdf AMG1000BOx VCM OBDII Vehicle Kit Installation Guide
23. nges or modifications not expressly approved by Vecima Networks Inc could void the user s authority to operate the equipment Industry Canada Compliance This device complies with Industry Canada license exempt RSS standard s Operation is subject to the following two conditions e This device may not cause interference and e This device must accept any interference including interference that may cause undesired operation of the device This device has been designed to comply with safety requirements for exposure to radio waves SAR in accordance with RSS 102 This device should be installed and operated with minimum distance 20cm between the equipment and your body Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes e L appareil ne doit pas produire de brouillage et e L utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement AMG1000BOx VCM OBDII Vehicle Kit Installation Guide 21 22 FLEETLYNX Cet artifice a t concu pour se plier la s curit les exigences pour l exposition aux ondes radio lectriques SAR dans conformit avec RSS 102 Cet artifice devrait tre install et fait marcher avec la distance minimale 20 centimetres entre l quipement et votre corps Under Industry Canada regulatio
24. ns this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for the transmitter by Industry Canada To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that necessary for successful communication Conform ment la r glementation d Industrie Canada le pr sent metteur radio peut fonctionner avec une antenne d un type et d un gain maximal ou inf rieur approuv pour l metteur par Industrie Canada Dans le but de r duire les risques de brouillage radio lectrique a l intention des autres utilisateurs il faut choisir le type d antenne et son gain de sorte que la puissance isotrope rayonn e quivalente p i r e ne d passe pas l intensit n cessaire l tablissement d une communication satisfaisante This radio transmitter IC 2943A AMG1020 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated Antenna types not included in this list having a gain greater than the maximum gain indicated for that type are strictly prohibited for use with this device Le pr sent metteur radio IC 2943A AMG1020 a t approuv par Industrie Canada pour fonctionner avec les types d antenne num r s ci dessous et ayant un gain admissible maxi
25. requested by the customer These kits require a connection to the OBDII data port found in model year 2008 and newer vehicles e AMG1000ALx VCM kits include the External Antenna and should be used when it is necessary to install the antenna on the vehicle exterior or if specifically requested by the customer These kits do not connect to the vehicle data port e AMG1000BLx VCM kits include the Backpack Antenna and will be used in the majority of cases where both the base unit and the antenna are to be installed in the vehicle interior These kits do not connect to the vehicle data port AMG1000BOx VCM OBDII Vehicle Kit Installation Guide FL ETLYNX 3 0 Pre Installation Steps M EEE E P LP LN P P M M LN LN A a 0 a SSI a a 0 a 0 a 0 a 0 0 0 a a a IMPORTANT PLEASE COMPLETE THE FOLLOWING TASKS BEFORE INSTALLATION Turn the vehicle on and check for existing lamps warning lights or anything out of the ordinary Investigate issues as needed before beginning the install this thorough pre install exam helps troubleshoot issues should any arise after installation Please record any lamps or warnings on the installation form Follow and ensure the completion of all steps in the FleetLynx Installation and Activation Form as well as the AMG1000 Quick Start Guide 3 1 Recommended Tools The following tools are recommended for the installation Phillips and Square Drive screwdrivers to unscrew the dashboard Carpenter knife
26. sky for the backpack antenna ideally as close to the front of the cab as possible 3 4 Allows the backpack antenna to mount parallel to the ground the ideal placement is horizontal without any metal objects between it and the sky Unscrew the antenna if needed to place the antenna in an ideal place Unit mounted with backpack attached to base cse CC NOT ADVISED BEST Ideally this side should be facing UP with no metal objects between it and the AVOID ENTIRELY Figure 4 Optimal Unit Orientation antenna attached to base BEST Backpack antenna and base unit mounted separately Ideally this side of the backpack antenna should be facing UP with no metal objects between it and the sky NOT ADVISED b Figure 5 Optimal Unit Orientation antenna separated from base AVOID ENTIRELY EN Note Record the Pre Installation Information on the Installation Form located in AMG Kit PROCEED WITH INSTALLATION ONLY AFTER THE ABOVE TASKS HAVE BEEN COMPLETED M EEE E LP LN LN LP P M M MN LN LN A AE A AE A E A A A A A A A 0 a 0 0 a a a a AMG1000BOx VCM OBDII Vehicle Kit Installation Guide FLEETLYNX 4 0 Connecting the AMG 4 1 AMG Base Unit Connections The AMG base unit connectors are shown in Figure 6 BN Note There are two cellular antenna connections one is for GSM and the other is for CDMA Be sure to check connections made to the AMG unit thoroughly GPS
27. that the AMG Serial Number shown here matches the serial number of the unit currently being checked CSM Modem Statua Hetwork Name ROGERS Service Provider ROGERS Signal Strength 61 dBm 5 5 Bars 100 4 The GSM registration status MUST read as Ercvisioned Yes Registered on a cellular network p Registered otherwise indicates a provisioning problem Roaming Antenna status Connection Connected to internet CDHE Modem Status Network Name 16410 Service Provider Telus Either the GSM or The CDMA registration status MUST readas Signal Strength 51 dBm 5 5 Bars 100 4 Te PMA TONpEcHON Registered on a cellular network Frovisioned Yes Maid ena otherwise indicates a provisioning problem Registered Ye PORNEA TOANE EMEL Roaming Na ZOOM Antenna status 0 The GPS antenna status MUST read as OK Connection Ne internet connection Valid lt The GPS signal status MUST read as Valid GPS ZD fix Yes GPS 3D fix Yes GPS HDOP Zl poor EPS satellite count amp GPS Antenna status OF Parking Brake Source Sensor If the brown Ignition Sensor wire IGN_SEN is connected then this reading MUST reflect the actual state of the ignition Ignition 5enase AMG Temperature 42 9 Celsius 103 2 Fahrenheit Figure 15 AMG Diagnostics Page Please note the following e GPS reception is not expected to be optimal inside the service bay it may be necessar
28. vehicle is running and Off when the vehicle is not running 7 2 6 Setting and Confirming CAN bus mode is set to OBDII This diagnostic web page is intended to support the OBDII installer before the AMG can make an internet connection This is only available while the AMG has not yet made a network connection to the Vecima configuration server The default mode for all AMG units is J1939 This page allows the installer to select OBDII as the data bus mode and a temporary configuration setting is made to run in this mode Once set to OBDII mode with the vehicle running and the harness plugged into the OBDII port the DATA LED will start to flash green In this way the installer can confirm good data bus connection before the cellular account is activated See the CAN Bus block in Figure 14 and Figure 15 for an example of what the installer might see 8 0 Return the AMG Installation Form Upon successful confirmation of AMG operation record the Post Installation Information on the Installation Form located in AMG Kit and fax the completed AMG Installation form to 306 657 3177 Based on the installation form that the installer sends to Vecima customer support center the AMG unit s permanent configuration will be set to OBDII on the central configuration management server When the AMG is able to connect to the central configuration management server over the cellular network it will download the permanent correct configuration AMG1000BOx VC
29. y to move the vehicle outside and give the GPS device a few minutes of satellite tracking time in order to get its lock e A registered CDMA or GSM modem does not mean provisioned Provisioning happens after the modem is activated and is registered on a home network tower Until the CDMA or GSM modem is able to provision it will not be able to establish an internet connection e Newer system firmware releases may appear slightly different than this page e f a GSM or CDMA network is not in range the modem will not be registered on the network If the AMG Diagnostics page is not indicating the required status please call 1 877 955 3122 for installation assistance Once all of the required status indications have been confirmed on the AMG Diagnostics page re install the dashboard AMG1000BOx VCM OBDII Vehicle Kit Installation Guide FLEETLYNX 7 2 2 Confirming AMG Serial Number Locate the block labeled Serial Number and confirm that this value agrees with the one written on the installation form 7 2 3 Confirming Cellular Status Locate the block labeled CELL Once the cellular account is activated one of either GSM or CDMA should read Registered Yes and Connection Connected to Internet 7 2 4 Confirming the GPS Reception Locate the block labeled GPS When outside GPS Signal Valid must be observed 7 2 5 Confirming the Ignition Sense Locate the block labeled Ignition Sense It should say On when the
Download Pdf Manuals
Related Search
AMG1000BOx VCM