DL12, DB12, DL14, DB14, DL17 system with CBD4, CBD5 or
Contents
1. 7 Examples where PIEZO avoids squeezing situations Page 22 of 36 Accessories and repair Ordering accessories Order from your nearest LINAK dealer or subsidiary Accessories Please contact your nearest LINAK dealer for information Repairs Systems should only be repaired by an authorised LINAK service centre or an engineer Systems to be repaired under warranty must be sent to an authorised LINAK service centre Warning By unauthorised opening of the system there is a risk that it may malfunction at a later date Spare parts Please contact your nearest LINAK dealer for information on spare parts Page 23 of 36 Disposal of LINAK products As LINAK customers often ask us how our products can be disposed of or scrapped we have prepared this guidance that enables a classification to different waste fractions for recycling or combustion Guidance We recommend that our products be disassembled as much as possible and divided into different waste groups for recycling or combustion For example waste can be sorted into metals plastics cable scrap combustible materials and recoverable resources Some of these main groups can be further divided into subgroups e g metal can be divided into steel aluminium copper and plastic can be divided into ABS PA PE PP As an example the table below breaks down the different components in LINAK products to various recycling groups Product Componen2. Mounting guidelines CBD4 CBD5 CBD6 The control box is to be fastened with 4 screws 3 screws for the CBD5 and theCBD6 with a head diameter between 8 and 10 mm Out of regard for the surface tension 10 mm is preferable due to lower surface tension See drawing appendix for placing of mounting holes and the space the CBD takes up CBD4 Control box CBD5 Control box CBD6 Control box The CBD must not be packed in heat insulating material but must be placed so that it can emit waste heat into the surroundings There are no ventilation holes to consider the CBD emits heat through the surface The plug must be visible when the CBD is mounted so that the supply to the CBD can be disconnected at replacement if any The mounting screws on the control box must be fastened with a max torque of 1 Nm The mounting surface to which the control box is attached should have a surface evenness of better than 0 5 mm CBD5 CBD6 bottom with cable grooves The bottom of the CBD5 CBD6 is equipped with two cable grooves improving the cable management when mounting The grooves can be used to bypass the CBD for both motor cables and the mains cable EU version only from one side to the other giving a cleaner design all Remember to lead the cables through the grooves before mounting the control box For mounting and operation of the desk panel please see the separate user manual for desk panels Page 18 of 3
3. Downwards the load will be approx 40 kg the load on the DL DB the desk what is on top of the desk The 40 kg are needed to activate the anti collision function Situations where the anti collision does not work There are situations where the anti collision will not be activated These situations are e f the collision happens during the initialisation phase e f the collision happens within the first 1000 msec or after the control button has been released e f the collision happens between the floor and the table and the load on the desk the weight of the legs are lower than 40 kg e f the collision happens over too long time e g if the collision is with a soft object Page 21 of 36 PIEZO description of the feature For optimised safety against squeezing and blocking on a desk LINAK has developed the DBs and columns with an integrated sensor called PIEZO The option minimises the risk for damages on a desk caused by squeezing or blocking of obstacles in up and down direction Examples could be driving down into an office chair or into a container or up into a windowsill To a certain extent the system also increases the personal safety but it does not comply with legislation describing personal safety PIEZO allows the DBs or columns to have the standard built in dimension and the standard stroke length There are no visible changes to the column 7 EX Ja RYN LL bg A INS Zam WY II A N MTN NY
4. E mail info bod ir www bod ir PERU Percy Martin Del Aguila Ubillus Phone 51 99 883 9879 RUSSIAN FEDERATION 000 FAM Phone 7 812 3319333 Fax 7 812 3271454 E mail purchase fam drive ru www fam drive ru SINGAPORE Servo Dynamics Pte Ltd Phone 65 6844 0288 Fax 65 6844 0070 E mail servodynamics servo com sg WWW Servo com sg SOUTH AFRICA Industrial Specialised Applications CC For contact details on other countries please visit www linak com or contact LINAK INTERNATIONAL Phone 45 73 15 15 15 Fax 45 74 45 90 10 Fax 45 73 15 16 13 Sales E mail infoGlinak com www linak com Phone 27 11 312 2292 or 27 11 2077600 Switch Board Fax 27 11315 6999 E mail gartht isagroup co za WWW iSaza co za UNITED ARAB EMIRATES Mechatronics Phone 971 4 267 4311 Fax 971 4 267 4312 E mail mechtron emirates net ae www mechatronics ae Page 36 of 36 USA U S Inc North and South American Headquarters Phone 1 502 253 5595 Fax 4 1 502 253 5596 E mail info linak us com www linak us com NORWAY LINAK Norge AS Phone 47 32 82 90 90 Fax 47 32 82 90 98 E mail info linak no www linak no POLAND LINAK Polska Phone 48 22 500 28 74 Fax 4 48 22 500 28 75 E mail dkreh linak dk www linak pl REPUBLIC OF KOREA LINAK Korea Ltd Phone 82 0 2 6231 1515 Fax 82 0 2 6231 1516 E mail scully linak kr www linak kr RUSSIAN FEDERATION 000 LINAK Phone 7 49
5. Mounting guidelines for the CBDA CBD5 CBDGS 18 Electrical connection of the DB DL system 4 eee emnes 19 Initialisation of the DESKLINE parallel 20 AU cL Go cl Us g asda ete 21 PIEZO description of the feature ii i e 22 Accessories 23 Disposal of LINAK 1 lt 24 Labels p 25 Drawing 27 Declaration OF conformity sander 33 Addresses soeben ers pU 36 Page 3 of 36 Preface We are delighted that you have chosen a product from LINAK A S LINAK systems are high tech products based on many years of experience in the manufacture and development of actuators electric control boxes controls and chargers We are also constantly improving our products to meet customer requirements This User Manual will tell you how to install use and maintain your LINAK DESKLINE products We are sure that the DESKLINE9 products will give you many years of problem free operation Before our products leave the factory they undergo full function and quality testing Should you nevertheless experie
6. 5183 5 DB12 Nominal lenght 500 3 mm Minimum lenght retracted at max load 4964 3 mm DB14 Nominal length 508 3mm Minimum length retracted at max load 503mm Page 30 of 36 CBD4 CBD5 W Inn SZ HIT Page 31 of 36 CBD6 Page 32 of 36 DECLARATION OF CONFORMITY LINAK A S Smedevaenget 8 DK 6430 Nordborg hereby declares that LINAK Actuator System composed of Control Box s CBD4 CBD5 CBD6 And Linear Actuator s 31 50 DB4 DB5 DB6 DB7 DB9 DB12 DB14 DB16 and or Lifting Column s DL1A DL2 014 DL5 DL6 DL7 DL8 DL9 DL10 DL11 DL12 DL14 DL15 DL 16 DL17 And Desk Panel s DP1C DP1K DPT DPB DPF DPBK DP1L DP1V DPA DPH WDPL1 and or Handset s HB2xxF2 00003 complies with EMC Directive 2004 108 EC according to following standards EN 61000 6 1 2007 EN 61
7. LINAK recommends that the DESKLINE9 DL system should be used in push applications wf Page 12 of 36 Mounting guidelines for the column DL14 Mounting foot The DL14 is supplied with 4 M6 threaded holes and 2 M8 screws for mounting of the foot You can either use 2 M8 screws or 4 M6 screws dependent on your foot design We advise you to use screws of a good quality min 8 8 and of a suitable length which must not go further than 16 mm into the DL14 column The thrust moment must not exceed 10 Nm in the bottom plate thread The holes in the foot ought to be sufficiently larger than 26 so that it is possible to bring the foot to a level line at assembly mounting of the table Bottom plate Mounted with 2 x M8 SSS VZLZA j ES ANNAN U Eww Np Min 10 mm LL TM NES NN S Tz Y NI 2 zzz 2 7 NNNNNNNNNNANNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNYS DLI4004 em Ne LIN a BSS Mounted with 4 x M6 221212121 RE TT TT AT A S a E kd DLI4003 Mounting guidelines for the column DL12 Mounting top Mounting foot The top of the column is supplied with 4 x M6 The DL12 is supplied with 4 x M6 t
8. USE ONLY IDENTICAL REPLACEMENT PARTS NOT TO OPENED BY UNAUTHORIZED PERSONNEL Page 25 of 36 Label for DB14 Label for DL14 LINAK APPLICATION POLICY The purpose of the application policy is to define areas of responsibilities in relation to applying a LINAK product defined as hardware software technical advice etc related to an existing or a new customer application LINAK products as defined above are applicable for a wide range of applications within the Medical Furniture Desk and Industry areas Yet LINAK cannot know all the conditions under which LINAK products will be installed used and operated as each individual application is unique The suitability and functionality of the LINAK product and its performance under varying conditions application vibration load humidity temperature frequency etc can only be verified by testing and shall ultimately be the responsibility of the LINAK customer using any LINAK product LINAK shall be responsible solely that LINAK products comply with the specifications set out by LINAK and it shall be the responsibility of the LINAK customer to ensure that the specific LINAK product can be used for the application in question Page 26 of 36 DRAWING APPENDIX DL12 DL14 DEIZ
9. damage to the product If leaking batteries are left in the product it might become defective It is recommended to use plastic gloves when handling leaking batteries The contents of leaking batteries can cause chemical burns and respiratory irritation If exposed to the contents of a leaking battery please wash with soap and water If irritation persists please seek medical attention In case of eye contact please flush eyes thoroughly with water for 15 minutes and seek medical attention Page 24 of 36 Label for DB12 _ DB1200000E660501 2013 10 07 _ P 0 12345678 0001 0 12345678 Label for CBDA WE IMPROVE YOUR LIFE DESIGNED IN DENMARK t CBD4P00020A 109 Date 00 120 V 60 Hz Pin 400W U Out 12 24 V File Et51104 Op 10 Max 2 min 18 min S W P N 0077432 1 22 DOUBLE INSULATED WHEN SERVISING USE ONLY IDENTICAL REPLACEMENT PARTS NOT TO OPENED BY UNAUTHORIZED PERSONNEL ASSEMBLED IN Label for CBD5 Label for CBD6 Label for DL12 U Out 12 24 V Op 10 Max 2 min 18 min Label for DL17 _ 0 2345678 0001 _ 042345678 WE IMPROVE YOUR LIFE m DESIGNED IN DENMARK CBD4P00020A 009 Date YYYY MM DD Uin 230V 50 Hz Pin 400W S W PIN 0077432 Ver 1 22 Cg A CAUTION DOUBLE INSULATED WHEN SERVISING
10. in typical applications Updated manuals and declarations can always be found here www linak com deskline Page 6 of 36 Only for EU markets This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision Only for Non EU markets Persons who do not have the necessary experience or knowledge of the product products must not use the product products Besides persons with reduced physical sensory or mental abilities must not use the product products unless they are under surveillance or they have been thoroughly instructed in the use of the apparatus by a person who is responsible for the safety of these persons Moreover children must be under surveillance to ensure that they do not play with the product It is the operator s responsibility to ensure that there is free space for the application to move without risk for the operator or bystanders before operating the application Misuse Do not overload the actuators this can cause danger of personal A injury and damage to the system Do not use the actuator system for lifting persons Do not sit or stand on a table whil
11. particular product Therefore LINAK reserves the right to discontinue the sale of any product displayed on its website or listed in its catalogues or other written material drawn up by LINAK All sales are subject to the Standard Terms of Sale and Delivery for LINAK For a copy hereof please contact LINAK LINAK A S reserve the right to make technical alterations Copyright LINAK 2013 10 MA M9 02 503 LINAK WE IMPROVE YOUR LIFE
12. use screws of a and of a suitable length of minimum 10 mm and must good quality min 8 8 and of a suitable length which not go into the column further than maximum 14 mm The screw torque must not exceed 10 Nm Min 10 mm Max 14 mm aA A dA aim TT must not go into the DL7 column further than 16 mm The screw torque must not exceed 10 Nm in the bottom plate thread The holes in the foot ought to be sufficiently larger than 1 6 so that it is possible to bring the foot to a level line at assembly mounting of the table R AS Psy 1 7 ie PITY 2 ARAN NS SN me i orm LZ IE NY WWW J O O S MC6 MC 8 EE As the desktop amplifies the sound we advise you to place a vibration shock absorbing material 2 between the desktop and the desk frame Example of how to mount the DESKLINE system Page 15 of 36 Mounting guidelines for DB12 and DB14 2 For detailed information on how to mount the DB12 or the DB14 please contact LINAK A S The top of the motor is supplied with holes for the self tapping special screws These screws together with the 2 rubber washers are supplied with the DB12 DB14 On the top of the motor there is the special rubber suspension which should always be used when the DB12 DB14 is mounted in a column The top flange where t
13. 000 6 3 2007 EN 55022 2011 A2 Class B complies with Low Voltage Directive 2006 95 EC according to the standard EN 60335 1 2012 EN 62233 2008 EN 62311 2008 complies with Machinery Directive 2006 42 EC according to the standard EN 13849 1 2008 SRP CS Cat B PL b and SRESW PL b complies with RoHS2 Directive 2011 65 EU And Controls RF transmitter HB1XRFXXXX and or RF transmitter HB2XRFXXXX and or RF receiver RFRL complies with the Radio equipment and Telecommunications terminal equipment Directive 1999 5 EC EN 300220 2 2006 EN 61000 6 1 2007 EN 61000 6 3 2007 EN 60335 1 2012 EN 62311 2008 Nordborg 2013 07 02 gt 2220 EP LINAK A S John Kling B Sc E E Certification and Regulatory Affairs Authorized to compile the relevant technical documentation Original Declaration Page 33 of 36 Page 34 of 36 Page 35 of 36 FACTORIES CHINA LINAK Shenzhen Actuator Systems Ltd Phone 86 755 8610 6656 Fax 86 755 8610 6990 E mail sales linak cn www linak cn SUBSIDIARIES AUSTRALIA LINAK Australia Pty Ltd Phone 61 3 8796 9777 Fax 61 3 8796 9778 E mail sales linak com au www linak com au AUSTRIA LINAK Repr sentanz Osterreich Wien Phone 43 1 890 7446 Fax 43 1 890 744615 E mail info linak de www linak at BELGIUM amp LUXEMBOURG LINAK Actuator Systems NV SA Phone 32 0 9 230 01 09 Fax 32 0 9 230 88 80 E mail info linak be www linak be BRAZIL L
14. 5 280 14 26 Fax 7 495 687 14 26 E mail info linak ru www linak ru SPAIN LINAK Actuadores S L u Phone 34 93 588 27 77 Fax 34 93 588 27 85 E mail linakact linak es www linak es SWEDEN LINAK Scandinavia AB Phone 46 8 732 20 00 Fax 46 8 732 20 50 E mail info linak se www linak se Terms of use SWITZERLAND LINAK AG Phone 41 43 388 31 88 Fax 41 43 388 31 87 E mail infoGlinak ch www linak ch TAIWAN LINAK A S Taiwan Representative Office Phone 886 2 27290068 Fax 886 2 27290096 Mobile 886 989292100 E mail michael chen linak com tw www linak com tw TURKEY LINAK ith ihr San ve Tic A S Phone 90 312 4726338 Fax 90 312 4726635 E mail info linak com tr www linak com tr UNITED KINGDOM LINAK UK Limited Phone 44 0 121 544 2211 Fax 44 0 121 544 2552 E mail sales linak co uk www linak co uk The user is responsible for determining the suitability of LINAK products for specific application LINAK takes great care in providing accurate and up to date information on its products However due to continuous development in order to improve its products LINAK products are subject to frequent modifications and changes without prior notice Therefore LINAK cannot guarantee the correct and actual status of said information on its products While LINAK uses its best efforts to fulfil orders LINAK cannot for the same reasons as mentioned above guarantee the availability of any
15. 6 Electrical connection of the DB DL system The DB DL system is to be connected as shown on figure 7 The DB DL is to be connected to the sockets on the control box by means of the motor cables which have a 6 pin plug in each end Finally the mains cable is to be mounted and power switched on Please note that the control box enr must only be connected to the voltage stated on the label CBDA CBD5 CBD6 with earth The CBD4 CBD5 CBD6 earth cable to be mounted on the desk construction typically the top frame in a way that ensures good electrical contact The function of the earth cable is to earth the desk and ground static electricity The earth connection does not protect other electrical products If the power cable is damaged it has to be replaced by an authorized LINAK service centre to avoid CBDA CBD5 with mains cut off non ZERO models any danger Hook for cable relief Mains cable DP WDPL DL DB Figure 7 Page 19 of 36 Initialisation of the DESKLINE parallel system The DESKLINE system is initialised by pressing the down button once or twice and holding it down until the DB DL runs into end stop It will then automatically run approx 5 mm out again and hereafter slowly run in again Only release the down button when the movement has stopped completely If the button is released before the sequence is completed the initialisation is interuppted and must ep be started again from the beginning The first
16. AND LINAK OY Phone 358 10 841 8700 Fax 358 10 841 8729 E mail linak linak fi www linak fi FRANCE LINAK France E U R L Phone 33 0 2 41 36 34 34 Fax 33 0 2 41 36 35 00 E mail linak linak fr www linak fr GERMANY LINAK GmbH Phone 49 6043 9655 0 Fax 49 6043 9655 60 E mail info linak de www linak de INDIA LINAK A S India Liaison Office Phone 91 120 4393335 Fax 91 120 4273708 E mail infoGlinak in www linak in IRELAND LINAK UK Limited Ireland Phone 44 0 121 544 2211 Fax 44 0 121 544 2552 44 0 796 855 1606 UK Mobile SLOVAKIA LINAK Slovakia s r o Phone 421 51 75 63 414 Fax 421 51 75 63 410 E mail jp linak sk www linak com ITALY LINAK Italia S r l Phone 39 02 48 46 33 66 Fax 39 02 48 46 82 52 E mail infoGlinak it www linak it JAPAN LINAK K K Phone 81 45 533 0802 Fax 81 45 533 0803 E mail linak linak jp www linak jp MALAYSIA LINAK Actuators Sdn Bhd Phone 60 4 210 6500 Fax 60 4 226 8901 E mail infoGlinak asia com www linak my NETHERLANDS LINAK Actuator Systems B V Phone 31 76 5 42 44 40 Fax 31 76 5 42 61 10 E mail infoGlinak nl www linak nl NEW ZEALAND LINAK New Zealand Ltd Phone 64 9580 2071 Fax 64 9580 2072 E mail nzsales linak com au www linak co nz 35 387 634 6554 Republic Of Ireland Mobile E mail sales linak co uk www linak co uk IRAN Bod Inc Phone 98 2188998635 6 Fax 98 2188954481
17. DESKLINE IMPROVING ERGONOMICS DL12 DB12 DL14 DB14 DL17 system with CBD4 CBD5 or CBD6 WE IMPROVE YOUR LIFE Page 2 of 36 Contents Prelate t PO 4 Important information sess 5 Safety instructions 5 General ERR 5 Before installation reinstallation or 6 Stat 6 MEM MEI MM RM 6 MISC DD 6 Only cls 7 Only tor Nom EU Markets NNI TET RT 7 8 Manufacturer s declaration E M 8 Misc on the DESKLINE system 9 FII TT 9 TO SU NOTE 9 Description of the DESKLINE 5 eene rennen nennen 10 Mounting guidelines for the DL14 ns 11 SR 11 PV ENS 13 Mounting guidelines for the column DL12 sss emnes 14 14 14 Mounting guidelines for the column 0117 2 1 sss eene 15 Mounting top aoe 0 ere dy recat I Em 15 DMN cue 15 Mounting guidelines for DB12 and DB14 ss 16
18. INAK Do Brasil Com rcio De Atuadores Ltda Phone 55 11 2832 7070 Fax 55 11 2832 7060 E mail info linak com br Wwww linak com br CANADA LINAK Canada Inc Phone 1 502 253 5595 Fax 1 416 255 7720 E mail info linak ca www linak us com CZECH REPUBLIC LINAK C amp S S R O Phone 420581741814 Fax 420581702452 E mail ponizil linak cz www linak cz DISTRIBUTORS ARGENTINA Novotec Argentina SRL Phone 54 11 4303 8900 54 11 4303 8989 Fax 54 11 4032 0184 E mail info novotecargentina com WWW novotecargentina com AUSTRALIA Ballarat Industrial Supplies www ballind com au BL Shipways amp Co www blshipway com au Gas Strut Marine and Industrial www gasstrutmarine com au Prime Motion amp Control www primehyd com au West Vic Industrial Supplies www westvicindustrial COLOMBIA MEM Ltda Phone 57 1 334 7666 Fax 57 1 282 1684 E mail servicioalcliente memltda com co www memltda com co INDONESIA Pt Himalaya Everest Jaya Phone 6 221 544 8956 6 221 544 8965 Fax 6 221619 4658 6 221 619 1925 E mail hejplastic div centrin net id www hej co id DENMARK LINAK A S Group Headquarters Guderup Phone 45 73 15 15 15 Fax 45 74 45 80 48 Fax 45 73 15 16 13 Sales E mail infoGlinak com www linak com DENMARK LINAK Danmark A S Phone 45 86 80 36 11 Fax 45 86 82 90 51 E mail linak linak silkeborg dk www linak dk FINL
19. al documentation is compiled in accordance with part B of Annex VII and that this documentation or part hereof will be transmitted by post or electronically to a reasoned request by the national authorities This partly completed machinery must not be put into service until the final machinery into which it is to be incorporated has been declared in conformity with the provisions of this Directive where appropriate Date 2010 01 01 Signature John Kling Certification and Regulatory Affairs Page 8 of 36 Misc on the DESKLINE system Warranty There is a 36 months warranty on DESKLINE products against manufacturing faults from the production date of the individual products see label LINAK A S warranty is only valid in so far as the equipment has been used and maintained correctly and has not been tampered with Furthermore the system must not be exposed to violent treatment In the event of this the warranty will be ineffective invalid For further details please see standard terms of sale and delivery for LINAK A S Maintenance Clean dust and dirt on the outside of the system at appropriate intervals and inspect them for damage and breaks Inspect the connections cables and plugs and check for correct functioning as well as fixing points Service of double insulated products Class Il A Class Il or double insulated electrical appliance is one which has been designed in such a way that it does not require a safety connect
20. e operating risk of personal injury Do not use the system in environments other than the intended indoor use Page 7 of 36 Repairs In order to avoid the risk of malfunction all DESKLINE repairs must only be carried out by authorised LINAK workshops or repairers as special tools must be used and special gaskets must be fitted Lifting units under warranty must also be returned to authorised LINAK workshops Warning If any of the DESKLINE products are opened there will be a risk of subsequent malfunction Warning The DESKLINE systems do not withstand cutting oil DECLARATION OF INCORPORATION OF PARTLY COMPLETED MACHINERY LINAK A S Smedevaenget 8 DK 6430 Nordborg Name and address of the person authorized to compile the relevant technical documentation John Kling Group Headquarters Guderup DK 6430 Nordborg email jklI linak com Herewith declares that LINAK Actuators and Actuator Systems comply with the following parts of the Machinery Directive 2006 42 EC ANNEX 1 Essential health and safety requirements relating to the design and construction of machinery 1 5 1 Electricity supply Directive 2006 95 EC on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage limits 1 5 10 Radiation 1 5 11 External radiation Directive 2004 108 EC on the approximation of the laws of the Member States relating to electromagnetic compatibility The relevant technic
21. he motor is mounted must be 4 mm thick 1 mm and the 2 mounting holes should be 212 mm with a centre distance of 36 mm The screw torque must be 2 Nm 0 1 Nm Top Special screws Rubber washer Rubber suspension Motor Middle tube For detailed information on how to mount the middle tube of your column please contact LINAK A S Bottom At the bottom of the DB12 or the DB14 the inner spindle should be mounted by means of a 22 teeth spline profile and a M5 screw in the bottom of the spindle Page 16 of 36 The DB12 DB14 gives the possibility of synchronous drive of the middle profile to make sure that ihe profiles are in the right place you have to secure that both the hollow and the massive spindles are driven in the bottom position For detailed information on how to mount the DB12 DB14 please contact LINAK A S From the factory the DB12 DB14 is delivered with the hollow spindle driven into end position Please Observe that the solid spindle may roll out during transportation handling but it must be rolled back wi to end position before mounting in the profile ul As the desktop amplifies the sound we advise you to place a vibration shock absorbing material 5 between the desktop and the desk frame n3 Do not drive the DB12 DB14 to the outer end position before mounting This will result in damaging the DB Example of how to mount the DESKLINE system Page 17 of 36
22. hreaded holes threaded holes meant for mounting onto the desk We advise you to use screws of a good quality min frame We advise you to fasten the desk frame by 8 8 and of a suitable length The length needs to be means of 4 x M6 screws of a good quality min 8 8 minimum 9 mm and of a suitable length minimum 12 mm The screw The screw torque must not exceed 10 Nm in the torque must not exceed 10 Nm bottom plate thread The holes in the foot ought to be sufficiently larger than 96 so that it is possible to bring the foot to a level line at assembly mounting of the table MC6 Min 9mm ss Min 12 mm Fus SIN A LLL Z AV AV AV AV AV AV AV AV AV AV 4 MC6 A AAA AAA AAA AA AAA AAP As the desktop amplifies the sound we advise you to place a vibration shock absorbing material E between the desktop and the desk frame Example of how to mount the DESKLINE system Page 14 of 36 Mounting guidelines for the column DL17 Mounting top The top of the column is supplied with 4 x MG threaded holes meant for mounting onto the desk frame We advise you to fasten the desk frame by means of 4 x MG screws of a good quality min 8 8 Mounting foot The DL17 is supplied with 4 x MG threaded holes and 2 x M8 screws for mounting of the foot You can use either 2 x M8 screws or 4 x MG screws dependent on your foot design We advise you to
23. information and access to this User Manual Follow the instructions for mounting risk of injury if these instructions are not followed The appliance is not intended for use by young children or infirm persons without supervision A If there is visible damage on the product it must not be installed Note that during construction of applications in which the actuator is to be fitted there must be no possibility of personal injury for example squeezing of fingers or arms ul Assure free space for movement of applications in both directions 7 to avoid blockade Page 5 of 36 Before installation reinstallation or troubleshooting e Stop the DB DL e Switch off the power supply and pull out the mains plug e Relieve the DB DL of any loads which may be released during the work Before start up e Make sure that the system has been installed as instructed in this User Manual e Make sure that the voltage at the control box is correct before the system Is connected to the mains e System connection The individual parts must be connected before the control box is connected to the mains See the User Manual for LINAK actuators if necessary During operation e f the control box makes unusual noises or smells switch off the mains voltage immediately e Take care that the cables are not damaged e Unplug the mains cable on mobile equipment before it is moved Misc The actuator system has a sound level below 55dB A
24. ion to electrical earth US ground The basic requirement is that no single failure can result in dangerous voltage becoming exposed so that it might cause an electric shock and that this is achieved without relying on an earthed metal casing This is usually achieved at least in part by having two layers of insulating material surrounding live parts or by using reinforced insulation There is no earthing grounding means provided on the product and no earthing grounding means is to be added to the product In Europe a double insulated appliance must be labelled Class I insulation symbol a square inside another square Servicing a double insulated product requires extreme care and knowledge of the system and is to be done only by qualified service personnel Replacement parts for a double insulated product must be identical to the parts they replace b The cleaners and disinfectants must not be highly alkaline or acidic pH value 6 8 11 1 double insulated or bear the double Page 9 of 36 Description of the DESKLINE system Each DESKLINE actuator column is equipped with a motor and parallel memory drive is ensured by means of software in the CBDA CBD5 CBD6 that also takes account of an oblique load on the desk Soft start and stop are also part of this software which ensures a soft start and stop when adjusting the desk Application of the DESKLINE system Irrespective of the load the duty cycle 1096 6 min hour
25. nce problems with your systems you are always welcome to contact our service departments or service centres LINAK subsidiaries and distributors all over the world have authorised service centres which are always ready to help you LINAK provides a warranty on all its products This warranty however is subject to correct use in accordance with the specifications maintenance being done correctly and any repairs being carried out at a service centre which is authorised to repair LINAK products Changes in installation and use of LINAK systems can affect their operation and durability Changes must therefore only be made by agreement with LINAK A S and are made at your own risk LINAK A S Page 4 of 36 Important information Important information on LINAK products can be found under the following headings Warning Failure to comply with these instructions may result in accidents involving serious personal injury Failing to follow these instructions can result in the product being v damaged or being destroyed Safety instructions A General Safe use of the system is possible only when the operating instructions are read completely and the instructions contained are strictly observed Failure to comply with instructions marked with the NOTE symbol may result in serious damage to the system or one of its components It is important for everyone who is to connect install or use the A systems to have the necessary
26. or max 2 min at continuous use stated in the data sheets must NOT be exceeded as this will result in a superheating of the motor and the control box Exceeding the duty cycle will result in a dramatic reduction of the life of the system The DB DL system range contains following products e 1 control box CBD4 CBD5 CBD6 e DL12 DB12 DL14 DB14 or DL17 1 4 e 1 exchangeable mains cable e motor cables 1 4 e DP1U DPF1M if memory function is required DP1C DPT DPF1C if memory function and display are required or 1 DPA DPB DP1K DP1V DPFK if only up down is required Page 10 of 36 Mounting guidelines for the DL14 system Mounting top The top of the column is supplied with 4 M6 threaded holes meant for mounting onto the desk frame We advise you to fasten the desk frame by means of 4 pcs M6 screws of a good quality min 8 8 and of a suitable length which must not go further than max 14 mm into the column The thrust moment must not exceed 10 Nm Screw length Min B 9 mm Max B 14 Top plate DLI4006 ET AN d n N 22 LLLA 1 02222222222 ebe top Absorbing material Min desk height Height of the DL in the lowest position 1 L X Floor level As the desktop amplifies the sound we advise you to place a vibration shock absorbing material E between the desktop and the desk frame Example of how to mount a 2 parallel DESKLINE9 DL system
27. ts Recycling group Columns Actuator Plastic housing Spindle and motor Metal scrap Plastic recycling or combustion Cable Cable scrap or combustion PC boards Electronic scrap Control Box PC boards Electronic scrap Plastic housing Plastic recycling or combustion Cable Cable scrap or combustion Transformer Metal scrap Handset Control Plastic housing Plastic recycling or combustion Cable Cable scrap or combustion PC boards Electronics scrap By now almost all our casted plastic parts are supplied with an interior code for plastic types and fibre contents if any Main groups of disposal Product main groups Metal scrap DL12 Cable scrap Electronics scrap Plastic recycling Comments or combustin DB12 DL14 DB14 DL17 CBD4 CBD5 CBD6 X DPXX Disposal of batteries Details regarding safe disposal of used and leaking batteries Batteries should be disposed in accordance with appropriate federal state and local regulations LINAK recommends that used or leaking batteries are disposed through local recycling systems Please do not throw used or leaking batteries in normal household waste or in nature This will cause damage to the enviroment How to deal with leaking batteries Leaking batteries should be disposed as described above If leaking batteries are discovered in the product the batteries must be removed at once to minimise
28. two times the system runs into the outward end stop it will automatically run approx 3 mm back in inward direction Approx 5 mm The CBD5 and the CBD6 can control the DL5 and the DL6 in 2 parallel while the CBD4 can control the DL5 and the DL6 in 2 3 and 4 parallel so that the desk is always kept horizontal Page 20 of 36 Anti Collision The function anti collision is an option for the standard CBD4 CBD5 CBD6 advanced control box software 0077432 version 1 66 and later A system with anti collision can limit material damages on a desk if a collision with a solid object should occur Enabling the anti collision To enable the anti collision function a little plug called a dongle must be mounted in one of the 2 control ports The function is only active when the dongle is mounted If you remove the dongle again you disable the function Method of operation When the DLs DBs are running the CBD4 CBD5 CBD6 monitors the current consumption on each channel using a special algorithm If the current consumption on one channel is increased by more than a predefined Slope a collision is assumed and all channels are stopped immediately and all DLs DBs will start to run in the opposite direction approx 50 mm This return drive is done automatically and continues with or without any control key pressed for max 2 5 sec The anti collision sensitivity is different in upward and downward direction Upwards the force is approx 20 kg
Download Pdf Manuals
Related Search