NF9G-QM77 User`s Manual
Contents
1. 4 SATA1 SATA2 SATAIII Port connector These connectors are speed ada ports that support 6 GB s transfer rate In the case that user install Mini SATA hard disk to MSATA slot SA TA2 port will be functionless 5 5 4 5 5 5 6 5 Port connector These connectors are high speed ports that support 3 GB s transfer rate eee Defnition 6 MSATA Mini SATAIII Port Connector MSATA slot can function as Mini SATA connecter or full size Mini PCIE slot When function as Mini SATA connector it can be connected to a single solid state hard disk driver and supports SATA 6Gb s specification mmm MSATA Connector 2 2 2 Headers 1 FP AUDIO 9 pin Line Out MIC In Header This header a RENE 2 Panel Line out MIC In connector with cable FP AUDIO 2 Pin 1 gt ON 2 ON LOIN LOIN 1400 ANI Line Out MIC Header dic 3 5 2 HDMI SPDIF Out header 41045 Pini 8 6 HDMI SPDIF Header 32852 5 4 5422 485 24 20 TITLE DO 2222 daxa dax Pin 12. HDMI Port VGA Port USB 2 0 Ports Motherboard Internal Diagram SATAIII Ports 5 1 2 Main Power connector SATAII Ports Serial Port Head erial Port Headers GPIO Header SEES 088 O Intel QM77 m ry p D go USB 3 0 Ports over HDMI Port Serial Port Header a Serial Port sz over VGA Port m LVDS Header Fr TX RX COM 58 0 H pite POb MIni SAT A Slot T eader RJ 45 Port over T C USB 3 0 Header USB 2 0 Ports a ATX 12V iE fever Connecto PUFAN Header dnuno 315333333 RJ 45 Port Display Port Intel rPGA988 Mini PCIE Slot CPU Socket Line OUT Line IN MIC IN Front Panel Audio Header KBMS Header HDMI SPDIF Header PCI Express x16 Slot 1 Headers for Jetway Daughter Board Expansion 00 5 TOD SS TS ZI O NICLED Headers TAA 0 p 8 SYSFANI Header PWRLED Header peaker Header Front Panel Header CIR Header USB 2 0 Header SYSFAN2 Header DDRIII SODIMM Slot x 2 DDRIII 1066 1333 Motherboard Jumper Position IPS JP3 2000 Audio CMP CASE Jumper Jumper Description 3 pin Block 3 pin Block 3 pin Block PCI E Power 3 3V 3VSB 3 pin
3. 25 Press T up down to choose in the main menu the option you want to confirm or to modify Press Enter to select Press lt gt lt gt keys when you want to modify the BIOS parameters for the active option F1 General help F2 Previous value F3 Optimized defaults F4 Save amp Reset Press Esc to quit the BIOS Setup 3 4 Getting Help Main Menu The on line description of the highlighted setup function is displayed at the top right corner the screen Status Page Setup Menu Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item To exit the Help Window press Esc 3 5 Menu Bars There are six menu bars on top of BIOS screen Main To change system basic configuration Advanced To change system advanced configuration Chipset To change chipset configuration Boot To change boot settings Security Password settings Save amp Exit setting loading and exit options User press the right or left arrow key the keyboard to switch from menu bar The selected one is highlighted 3 6 Main Menu Main menu screen includes some basic system information Highlight the item and then use the lt gt or lt gt and numerical keyboard keys to select the value you want in each item Setup 011111 Copyright C 2011 American Megatrends Inc B
4. 2 Pin 1 17 CPUFAN 3 FAN Speed Headers EEEBE an Clock JOMOd 4 2019 Pin1 GND 12 Fan Power 8589 CPUFAN SYSFANI SYSFAN 2 Header 18 1 2 35 Pin Jetway Daughter Board Header These two Headers can add the COM Port card LAN card Em 0 0 297 imi ni CNI CN2 Header Chapter 3 Introducing BIOS Notice The BIOS options in this manual are for reference only Different configurations may lead to difference in BIOS screen and BIOS screens in manuals are usually the first BIOS version when the board is released and may be different from your purchased motherboard Users are welcome to download the latest BIOS version form our official website The BIOS is a program located on a Flash Memory on the motherboard This program is a bridge between motherboard and operating system When you start the computer the BIOS program will gain control The BIOS first operates an auto diagnostic test called POST power on self test for all the necessary hardware it detects the entire hardware device and configures the parameters of the hardware synchronization Only when these tasks are completed done it gives up control of the computer to operating system OS Since the BIOS is the only channel for hardware and software to communicate it is the key factor for system
5. Enabled GTT Size The optional settings 1MB 2MB Aperture Size The optional settings 128MB 256MB 512MB DVMT Pre Allocated Use this item to select DVMT 5 0 pre allocated fixed graphics memory size used 37 by the internal graphics device DVMT Total Gfx Mem Use this item to select DVMT 5 0 total graphics memory size used by the internal graphics device LCD Control Primary IGFX Boot Display The optional settings are VBIOS default CRT HDMI DP LVDS Secondary IGFX Boot Display The optional settings are Disabled CRT HDMI DP LVDS Note The above item shall appear when Primary IGFX Boot Display is set as CRT HDMI DP or LVDS Active LFP The optional settings are Disabled Enabled North PCle Configuration Press Enter to make settings for the following sub items NB PCle Configuration PEGO Gen X The optional settings are Auto Gen1 Gen2 Gen3 PEGO ASPM The optional settings are Disabled Auto ASPM LOs ASPM L1 ASPM LOsL 1 Enable PEG The optional settings are Auto Enabled Disabled Detect Non Compliance Device Use this item to enable or disable the function of detecting non compliance PCI Express device in PEG De emphasis Control The optional settings are 6 dB 3 5 dB Memory Configuration Press Enter to make settings for the following sub items DIMM profile Use this item to select D
6. A U N r Old5 6415 049 6 0149 69 0190 A 9 Old9 t Old5 85 Old5 89 0139 7 USB1 USB2 9 USB 2 0 Port Header DA 1 N ON 8 556 119 gt gt Ny _ lt 33 00 Gashs 6 LH i 10 1 165 155 1 855 LXHSS 9 5M BUS 4 5 Pin 1 Pin2 Pin 1 ASIDA SNANS PinNO Pin Define Pin Define 0 11 INVERTER 8 Pin LVDS Inverter Header 1 INVERTER 20 12 CIR 7 Pin CIR Header N 2 25 lt 00 wu maqa A c T i 8 mm T Pint m e 14 PWR LED 3 pin PWR LED Header The Power LED is light on while the system power is on Connect the Power LED from the system case to this pin header 21 15 SPEAK 4 Speaker Header This 2 pin header connects to the case mounted speaker See the figure below edr 7 TE _ SPEAK Pin 1 lt Z Z ooo m PWRLED 32 2
7. stability and in ensuring that your system performance as its best 3 1 Entering Setup Power on the computer and by pressing Del immediately allows you to enter Setup If the message disappears before your respond and you still wish to enter Setup restart the system to try again by turning it OFF then ON or pressing the RESET button on the system case You may also restart by simultaneously pressing Ctrl lt Alt gt and Delete keys If you do not press the keys at the correct time and the system does not boot an error message will be displayed and you will again be asked to Press gt Del to enter Setup 3 2 BIOS Menu Screen The following diagram show a general BIOS menu screen Amarican Megatrends Inc BIOS Information BIOS Vendor Core Version Bulld Date and Time American Megatrends 4 6 5 3 08 31 2012 16 45 40 Tue 06 2012 System Time 13110119 Access Level Administrator Current Setting Value Menu Items Function Key BIOS Menu Screen 3 3 Function Keys Menu Bar iet the Date Use Tab to witch between Data elements General Help Items Select Screen Th Select Item Select gt Change Opt In the above BIOS Setup main menu of you can see several options We will explain these options step by step in the following pages of this chapter but let us first see a short description of the function keys you may use here e Press lt right to select screen
8. surface of the components can bring about phenomena as minor as computer instability resulted from corrosion and oxidation from components and PCB or as major as short circuit that can burn the components Suggest starting the computer until the temperature goes up The increasing temperature of the capacitor may decrease the life of computer Using the close case may decrease the life of other device because the higher temperature in the inner of the case Attention to the heat sink when you over clocking The higher temperature may decrease the life of the device and burned the capacitor iii USER S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER NO PART OF THIS MANUAL INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER BOARD SERIES AND WE DO ASSURE THIS MANUAL MEETS USER S REQUIREMENT BUT WILL CHANGE CORRECT ANY TIME WITHOUT NOTICE MANUFACTURER PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND AND WILL NOT BE LIABLE FOR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING DAMAGES FOR LOSS OF PROFIT LOSS OF BUSINESS LOSS OF USE OF DATA INTERRUPTION OF BUSINESS AND THE LIKE PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RES
9. to make settings for the following sub items Super IO Confiquration COM1 Port Configuration COM2 Port Configuration COM3 Port Configuration Press Enter to make settings for the following items Serial Port Use this item to enable or disable serial port Change Settings Use this item to select an optimal setting for super IO device COM4 Port Configuration Press Enter to make settings for the following sub items Serial Port Use this item to enable or disable serial port Change Settings Use this item to select an optimal setting for super IO device Serial Port Mode Select Use this item to set serial port as 5232 or RS422 485 WatchDog Configuration Press Enter to make settings for Watchdog Configuration Watchdog Configuration WatchDog Timer Control Use this item to enable or disable WatchDog Timer Control When set as Enabled the following sub items shall appear WatchDog Timer Val User can set a value in the range of 4 to 255 WatchDog Timer Unit The optional settings are Second Minute Shutdown Temperature Configuration Use this item to select system shutdown temperature CPU PPM Configuration 34 Press Enter to make settings for CPU PPM Configuration CPU PPM Confiquration EIST Use this item to enable or disable Intel SpeedStep Turbo Mode Use this item to enable or disable Turbo mode CPU C3 Report Use this item to enable or disable CPU C3 ACPI C2 report to OS CPU C6 Report Use
10. Block Select 3 pin Block 6 pin Block 6 pin Block 2 pin Block Connectors Conector UL1 Middle Bottom USB 2 0 Port Connector x2 DP Line Out Line In MIC Audio Connector Headers Header Description AUDIO 9 pin block KBMS 6 pin block SPDIF 2 pin Block 2 3 4 9 block TX RXCOM 4 pin block GPIO 10 pin Block USB1 2 9 pin block USB4 19 pin Block SM_BUS 4 pin block LVDS 35 pin Block INVERTER 8 pin Block CIR 7 pin Block NIC_LED1 NIC_LED2 2 pin Block PWR LED 3 pin Block SPEAK 4 pin Block LED Power Button Reset CPU FAN 4 pin Block SYSFAN1 SYSFAN2 3 pin Block CN1 CN2 35 pin Block Chapter 2 Hardware Installation 2 1 Jumper Setting 1 TS Clear CMOS 1 2 Short Normal 2 3 Short Clear CMOS CMOS Clear Setting om JP3 JP3 2 3 closed LVDS 3 3V 3 JP5 3 pin Inverter 5V 12V Select Om i i 8844 cn TT om BERE JP9 E 3 1 2 closed Mini SATA Mini PCIE Slot VCC VCC3 3V JP9 2 3 closed Mini SATA Mini PCIE Slot VCC 3VSB 5 JP11 Mini PCI E Power VCC3 3V 3VSB Function Select 6 288 11 9 3 1 2 closed Mini P
11. CI E Slot VCC VCC3 3V JP11 2329354352345331 e Gu A BBE ama JP10 e GE 1 2 closed RS232 3 4 closed 12V 5 6 closed 45V 7 JP12 6 4 Header RS232 422 485 Function Select om SS 881 1 2 closed 5232 3 4 closed RS485 5 6 closed RS422 om Soom Pin 1 2 die function enabled Use needs to enter BIOS and enable Case Open Detect function In this case if you case is removed next time when you restart your computer a message will be displayed onscreen to inform you of this 11 2 2 Connectors and Headers 2 2 1 Connectors 1 Rear Panel Connectors RJ 45 LAN Ports Serial Port Line OUT Line IN Display Port MIC IN HDMI Port VGA Port USB 2 0 Ports 2 ATXPWR 24 pin block Main Power Connector e e PIN ROWI ROW2 was ROW1ROW2 1 3 3V 3 3V 1 Y 2 3 3V 12V 5V GND GND Power OK 5V 5V Stand b 5V 10 12 4 Ge Ni o ll 12 Fin 1 Fin 1 12 3 3V GND 20 4 Pin 24 pin Main Power Connector 3 ATX12V 4 pin block ATX1 ai Lu Power Connector Gao a
12. CI Express links if this option is set as Disable Link ACPI Settings Press Enter to make settings for the following sub items ACPI Settings ACPI Sleep State Use this item to select the highest ACPI sleep state the system will enter when the suspend button is pressed 53 Video Repost Use this item to enable or disable S3 video report Wakeup Function Settings Press Enter to make settings for the following sub items Wake System with Fixed Time Use this item to enable or disable system wake on alarm event When set as Enabled system will wake on the hour min sec specified CIR Wakeup Use this item to enable or disable CIR wakeup PS2 KB MS Wakeup Use this item to enable or disable 52 KB MS wakeup function This function is only supported when ERP function is disabled USB S3 S4 Wakeup Use this item to enable or disable USB 53 54 wakeup This function is only supported when ERP function is disabled CPU Configuration Press Enter to make settings for the following sub items Hyper Threading The optional settings are Disabled Enabled Active Processor Cores Use this item to select number of cores to enable in each processor package Limit CPUID Maximum The optional settings are Disabled Enabled This item should be set as Disabled for Windows XP Execute Disable Bit The optional settings are Disabled Enabled Intel Virtualization Technology The optional settings Enabled Disabl
13. IMM timing profile that should be used Memory Frequency Limiter 38 Use this item to set maximum memory frequency selection in Mhz ECC Support Use this item to enable or disable DDR ECC support MMode Support The optional settings are Auto 1N Mode 2N Mode Memory Remap Use this item to enable or disable memory remap above 4G The optional settings are Enabled Disabled 3 9 Boot Menu Aptio Setup Utility Copyright C 2011 American Megatrends Inc psi Boot Conf Lgurat Lon Bootup NumLock State Off Quiet Boot 015417106 Fast Boot Olsabled CSH16 Module Version 07 69 Gaten20 Active Upon Request Option ROM Hessages Force BIOS INTL Trap Response Immed ate Boot 001100 Priorities Number of seconds to walt for setup activation 65536 means indefinite ualting jAk Select Screen Select Item Select Change Opt FI General Help Previous Values Optimized Defaults Fat Save 8 Reset ESCI Exit Boot Configuration Setup Prompt Timeout Use this item to set number of seconds to wait for setup activation key Bootup Numlock State Use this item to select keyboard numlock state The optional settings are On Off Quiet Boot The optional settings are Enabled Disabled Fast Boot The optional settings are Enabled Disabled Gate A20 Active The optional settings are Upon Request Always Option
14. IOS Information Set the Date Use Tab to BIOS Vendor American Megatrends switch between Data elements Core Version 4 6 5 3 Bulld Date and Time 08 31 2012 16 45 40 Tue 06 2012 System Time 13110119 Access Level Administrator Enter Select 15 1 Change Opt General Help F2 Previous Values Optimized Defaults Fat Save 8 Reset ESCI Exit System Date Set the date Please use Tab to switch between data elements System Time Set the time Please use Tab to switch between time elements 3 7 Advanced Menu Aptio Setup Utility Copyright C 2011 American Megatrends Inc Controls the execution of UEFI ERP Support Enab led and Legacy PXE OpROM POI Express Settings k ACPI Settings Wakeup function Settings CPU Configuration k SATA Configuration b Intel R Rapid Start Technology k PCHeFW Configuration Conf 1gurat Lon k 058 Configuration b SMART Settings k Super IO Configuration Select Screen k PO Health Status 11 Select Item Serial Port Conf Lon Entar Select Hatchdog Configuration Shutdown Temperature Configuration CPU PPM Configuration iT Optimized Defaults Fat Save 8 Reset ESC Exit Launch PXE OpROM Policy The optional settings are Do not launch only Legacy only Use this item to enable or disable boot option for legacy network devices ERP Function Use this item to enable or disable ERP func
15. PECTIVE COMPANIES AND THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER S BENEFIT WITHOUT INTENT TO INFRINGE Manual Revision Information Reversion Revision History Date 1 0 First Edition 2012 08 28 Item Checklist Motherboard DVD for motherboard utilities Users Manual Cable s 1 O Back panel shield Chapter 1 Introduction of the Motherboard 1 1 Feature of Motherboard Intel QM77 express chipset Intel Socket G 988 supporting compatible Intel CoreTM i3 15 i7 Mobile Processors under 45W power consumption with low power consumption never denies high performance Support 2 1066 1333 1600 MHz DDRIII SO DIMM up to 16GB and dual channel function Integrated with Intel 82574L and Intel 82579LM Gigabit Ethernet LAN chip Integrated ALC662 6 channel HD Audio Codec oupport USB 3 0 data transport demands Support PCI Express x16 and Mini PCIE slot Integrated with 24 bit dual channel LVDS 4 SATAII ports and 2 SATAIII ports HDMI DP and Video Outputs Support CPU Smart Supports 53 Function Compliance with EuP Standard Watchdog Timer Technology 1 2 Specification Bescipion Design e Mini ITX form factor 6 layers PCB size 17 0x17 0cm Chipset Intel QM77 Express Chipset Intel socket G rPGA 9888 CPU Socket e pesi up to Intel Core i3 15 i7 Mobile Processors under power consumption
16. ROM Message Use this item to set display mode for option ROM The optional settings are Force BIOS Keep Current INT19 Trap Response The optional settings are Immediate Postponed Immediate to execute the trap right away Postponed to execute the trap during legacy boot Boot Option Priorities Boot Option 1 Boot Option 2 Use this item to decide system boot order from available options Hard Drive BBS Priorities Use this item to set the order of the legacy devices in this group 3 10 Security Menu Aptio Setup RU Copyright 2011 American Megatrends Inc Security Password Description hdministrator Passuord If ONLY the Administrator s password 15 set then this only Limits access to Setup and 15 only asked for when entering Setup If ONLY the User s password 16 set then this 18 power on password and must be entered to boot enter Setup In Setup the User will have Administrator rights The password length must be In the following range Minimum length Maximum length Select Screen Select Item Enter Select User Password Change Opt Fit General Help F2 Previous Values Optimized Defaults 114 Save 8 Reset Esc Exit H 11 oecurity menu allow users to change administrator password and user password settings 3 11 Save amp Exit Menu 111121 Setup Utility Copyright 2011 American Megatrends Inc Chipset Sa
17. TECHNICAL MANUAL Of intel 77 Express Chipset Based Mini ITX M B G03 NF9G F Revision 1 0 Release date August 28 2012 Trademark Specifications and Information contained in this documentation are furnished for information use only and are subject to change at any time without notice and should not be construed as a commitment by manufacturer Environmental Protection Announcement Do not dispose this electronic device into the trash while discarding To minimize pollution and ensure environment protection of mother earth please recycle TABLE OF CONTENT ENVIRONMENTAL SAFETY INSTRUCTION iii USER S NOICE MANUAL REVISION INFORMATION JJ GREG CHAPTER 1 INTRODUCTION THE MOTHERBOARD 11 FEATUREOFMOTHERBOARD uu uu ULU 1 142 SPECIFICATION u u u M 2 1 3 DIAGRAM u u c 3 CHAPTER 2 HARDWARE INSTALLATION 2 1 ccc a 8 2 2 CONNECTORS AND HEADEHNS UD NE J J 12 2 2 1 OGONNECIOHOS u uu uuu RUM ee ne ee ee
18. e NA ee 12 2 2 2 HEADERS u 15 CHAPTER 3 INTRODUCING BIOS ENTERING SETUP v n FEX EUH 24 3 2 BIOS MENU SCREEN 25 MI euelBicim 25 Ja uuu u 26 959 T 26 ME hunAI ljbeee 27 ADVANCED MENU u eee 28 36 Me llu i iBu lu 35 TI cR 39 SECURITY MENU u u uuu 41 a i SAVESEXIFMENU uu ul l 42 ii AUTION Environmental Safety Instruction Avoid the dusty humidity and temperature extremes Do not place the product in any area where it may become wet 0 to 60 centigrade is the suitable temperature The figure comes from the request of the main chipset Generally speaking dramatic changes in temperature may lead to contact malfunction and crackles due to constant thermal expansion and contraction from the welding spots that connect components and PCB Computer should go through an adaptive phase before it boots when it is moved from a cold environment to a warmer one to avoid condensation phenomenon These water drops attached on PCB or the
19. ed When set as Enabled a VHM can utilize the additional hardware capabilities provided by Vanderpool Technology Hardware Prefetcher Use this item to turn on off the Mid Level Cache L2 streamer prefetcher 30 Adjacent Cache Line Prefetch Use this item to turn on off prefetching of adjacent cache lines SATA Configuration Press Enter to make settings for the following sub items SATA Controller s The optional settings are Disabled Enhanced IDE Legacy Native Mode Select The optional settings are Native Legacy SATA Mode Selection The optional settings are IDE AHCI RAID Intel R Rapid Start Technology Use this item to enable or disable Intel R Rapid Start Technology Note This item be not available depending on different hardware configuration PCH FW Configuration Press Enter to see ME information and make settings for Firmware Update Configuration Firmware Update Configuration Press Enter to make settings for ME FW Image RE Flash ME FW Image RE Flash Use this item to enable or disable ME FW Image Re Flash function AMT Configuration Press Enter to make settings for the following sub items Intel AMT Use this item to enable or disable Intel Active Management Technology BIOS Hotkey Pressed The optional settings are Disabled Enabled MEBx Selection Screen The optional settings are Disabled Enabled Hide Un Configure ME Confirmation The optional s
20. ettings are Disabled Enabled MEBx Debug Message Output 31 The optional settings are Disabled Enabled Un Configure ME The optional settings are Disabled Enabled Amt Wait Timer Use this item to set time to wait before sending GET BOOT OPTIONS Disable ME The optional settings are Disabled Enabled ASF Use this item to enable or disable alert specification format Active Remote Assistance Process The optional settings are Disabled Enabled USB Configure Use this item to enable or disable USB configure function PET Progress Use this item to enable or disable PET events progress to receive PET event or not USB Configuration Press Enter to make settings for the following sub items Legacy USB Support The optional settings are Auto Disabled Enabled USB 3 0 Support Use this item to enable or disable USB3 0 controller support XHCI Hand off The optional settings are Disabled Enabled EHCI Hand off The optional settings are Disabled Enabled USB hardware delay and time out USB Transfer time out Use this item to set the time out value for control bulk and interrupt transfers Device reset time out Use this item to set USB mass storage device start unit command time out Device power up delay Use this item to set maximum time the device will take before it properly reports 32 itself to the host controller Auto uses default value fo
21. for detailed CPU support information please visit our website DDRIII SO DIMM slot x2 Memorv Slot support DDHIII 1066 1333 1600 MHz DDHIII SO DIMM y expandable to 16GB Support dual channel function 1 pcs of PCI Express x16 slot Expansion Slot 1 pcs of half size Mini PCIE slot 1 pcs of full size Mini PCIE Mini SATA slot Integrated Intel 82574L and 82579LM Gigabit Ethernet Dual LAN Chip LAN chip that support Fast Ethernet LAN function of providing 10 100 1000Mbps Ethernet data transfer rate Audio Chi e Realtek ALC662 6 channel Audio Codec integrated Audio driver and utility included BIOS 64M DIP Flash ROM e HDMI port connector x1 VGA port connector x1 COM port connector x 1 USB 3 0 port connector x2 USB 2 0 port connector x2 RJ 45 LAN connector x2 Display port connector x1 Audio connector x3 Line in Line out MIC SATAIII port connector x2 SATAII port connector 4 Front panel audio header x1 Multi KBMS header x1 L VDS header x1 LVDS Inverter header x1 HDMI SPDIF header x1 GPIO header x1 Serial port header x3 TX RXCOM header x1 USB 2 0 header x2 support four expansion USB 2 0 ports USB 3 0 header x1 support two expansion USB 3 0 ports CIR header x1 SM BUS header x1 NICLED header x2 Speaker header x1 PWRLED header x1 Front panel header x1 1 3 Layout Diagram Rear IO Diagram RJ 45 LAN Ports Serial Port Line OUT USB 3 0 Ports Line IN Display Port MIC IN
22. optional settings are Enabled Disabled USB Port Pre Port Disable Control Use this item to control each of the USB ports 0 13 disabling Azalia HD Audio The optional settings are Disabled Enabled Auto Azalia Internal HDMI Codec Use this item to enable or disable internal HDMI codec for Azalia HDMI Port Output The optional settings are Enabled Disabled DP Port Output The optional settings are Enabled Disabled 36 Onboard 1 Controller Use this item to enable or disable onboard LAN controller Wake on LAN1 from S5 Use this item to enable or disable integrated LAN to wake the system Onboard Lan2 Device Use this item to control the PCI Express root port High Precision Event Timer Confiquration High Precision Timer The optional settings are Enabled Disabled Restore AC Power Loss Use this item to select AC power state when power is re applied after a power failure The optional settings are Power Off Power On Last State System Agent SA Configuration Press Enter to make settings for the following sub items VT d The optional settings are Enabled Disabled Enable NB CRID The optional settings are Enabled Disabled Graphics Configuration Press Enter to make further settings for Graphics Configuration Graphics Confiquration Primary Display The optional settings are IGFX PEG Internal Graphics The optional settings are Auto Disabled
23. r a root port it is 100 ms for a hub port the delay is taken from hub descriptor The optional settings Auto Manual Select Manual you can set value for the following sub item Device Power up delay in seconds the delay range in from 1 to 40 seconds in one second increments SMART Settings Press Enter to make settings for SMART Self Test The optional settings are Disabled Enabled Super IO Configuration Press Enter to make settings for the following sub items Super IO Confiquration CIR Controller Use this item to enable or disable CIR controller Case Open Detect Use this item to detect case has already open or not show message in POST PC Health Status Press Enter to view hardware health status SmartFan Configuration Press Enter to make settings for SmartFan Configuration Smart Fan Confiquration CPUFAN SYSFAN1 Smart Mode When set as Enabled the following sub items shall appear CPUFAN Full Speed Temperature SYSFAN1 Full Speed Temperature Use this item to set CPUFAN SYSFAN full speed temperature Fan will run at full speed when above this temperature CPUFAN Idle Speed Temperature SYSFAN1 Speed Temperature Use this item to set CPUFAN SYSFAN idle speed temperature Fan will run at idle speed when below this temperature CPUFAN SYSFAN Idle Speed Duty Use this item to set specific duty at which CPUFAN SYSFAN will run at idle speed 33 Serial Port Configuration Press Enter
24. this item to enable or disable CPU C6 ACPI C3 report to OS 3 8 Chipset Menu hptio Setup Utility Copyright C 2011 American Hegatrends Inc Chipset PCH Parameters k System Agent SA Configuration 138 Select Screen Select Item Enter Select 14 1 Change Opt F1 General Help iFa Previous Values Optimized Defaults Save 8 Reset ESCI Exit Configuration Press Enter to make settings for the following sub items USB Devices Configuration Press Enter to make further settings USB device configuration USB Device Confiquration XHCI Pre Boot Driver Use this item to enable or disable Pre Boot Driver Support XHCI Mode The optional settings are Smart Auto Auto Enabled Disabled HS Port 1 Switchable HS Port 2 Switchable HS Port 3 Switchable HS Port 4 Switchable The optional settings are Disabled Enabled These items allow for HS port switching between and EHCI If set as Disabled port is routed to EHCI Note The above items shall not appear when Mode is set as Disabled XHCI Streams The optional settings are Disabled Enabled Use this item to enable or disable XHCI Maximum Primary Stream Array Size Note The above item shall not appear when XHCI Mode is set as Disabled EHCI1 EHCI2 Use this item to enable or disable USB EHCI USB 2 0 support One EHCI controller must always be enabled The
25. tion for this board This item should be set as Disabled if you wish to have Active All Wakeup Function PCI Subsystem Settings Press Enter to enter and make settings for the following sub items PCI Express Device Register Settings Relaxed Ordering Use this item to enable or disable express device relaxed ordering 28 Extended Tag If set as Enabled it will allow device to use 8 bit tag field as a requester No Snoop Use this item to enable or disable PCI Express device No Snoop option Maximum Payload Use this item to set maximum payload of PCI Express device or allow system BIOS to select the value Maximum Read Request Use this item to set maximum read request size of PCI Express device or allow system BIOS to select the value PCI Express Link Register Settings ASPM Support The optional settings Disabled Auto Force LOs Extended Synch If set as Enabled it will allow generation of extended synchronization patterns Link Training Retry Use this item to define number of retry attempts software will take to retrain the link if previous training attempt was unsuccessful Link Training Timeout uS Use this item to define number of microseconds software will wait before polling Link Training bit in link status register Value ranges from 10 to 1000 Unpopulated Links The optional settings are Keep Link Disable Link In order to save power software will disable unpopulated P
26. ve 8 Exit Reset the system after saving Discard Changes and Reset the changes Restore Defaults Saye as User Defaults Restore User Defaults Boot Override Launch EFI Shell from fliesystem device 11 Select Screen Select Item Enter Select 1 Change Opt General Help Fe Previous Values F3 Optimized 06180115 Save Changes and Reset This item allows user to reset the system after saving the changes Discard Changes and Reset This item allows user to reset the system without saving any changes Restore Defaults Use this item to restore load default values for all the setup options Save as User Defaults Use this item to save the changes done so far as user defaults Restore User Defaults Use this item to restore defaults to all the setup options Launch EFI Shell from file system device This item is for attempts to launch EFI shell application Shell x64 efi from one of the available filesystem devices
Download Pdf Manuals
Related Search