MultiBEAM LED-Variable White-Zoom
Contents
1. device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported For safety reasons please be aware that all modifications on the device are forbidden If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to short circuit burns electric shock lamp explosion crash etc INSTALLATION INSTRUCTIONS Mounting the device CAUTION Please consider the GB7000 15 EN60598 2 17 and the other respective national norms during the installation The installation must only be carried ont by a qualified person The applicable temperature for the lignting is between 25 C to 45 C Do not use the lighting under or above the temperature The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight for hour without any harming deformation The installation must always be secured with a secondary safety attachment e g an appropriate safety rope Never stand directly below the device when mounting removing or servicing the fixture The operator has to make sure the safety relating and machine technical installations are approved by an expert before taking the device into operation for the first time These installations have to be approved by a skilled person once a year edi s XM2. display shows D XX X stands for the DMX value of the selected channel 10 XM471 V1 0 NR FLIP Reverse display With this function you can rotate the display by 180 l 2 3 Select FLIP by pressing UP or DOWN button Press ENTER the display shows ON or OFF Press UP to select ON if you wish to enable this function or press DOWN button to OFF if you don t the display will rotate by 180 Press ENTER to confirm or Press MODE ESC to return to the main menu nm e Uli Shut off LED display With this function you can shut off the LED display after 2 minutes L PA 3 Select D ON by pressing UP or DOWN button Press ENTER the display shows ON or OFF Press UP to select ON if you wish to enable this function or press DOWN button to OFF if you don t 4 Press ENTER to confirm or Press MODE ESC to return to the main menu EINE Ii LU locked keys the display With this function you can locked keys the display l N 99 Select LOCK by pressing UP or DOWN button Press ENTER the display shows ON or OFF Press UP to select ON if you wish to enable this function or press DOWN button to OFF if you don t Press ENTER to confirm or Press MODE ESC to return to the main menu Vn rr Main menu 1 I 2 Press MODE ESC to enter the main m
3. i Eg E ri I 1 IC HUGE 1 LCI Main menu 0 Press MODE ESC to enter the main menu MODE display flashing 2 Press ENTER and select ADDR RUN or DISP by pressing UP or DOWN button 3 Press ENTER for selecting the desired sub menu Mide Bade IIC eis HALL DMX address setting With this function you can adjust the desired DMX address via the Control Board l Select VALU by pressing UP or DOWN button 2 Press ENTER adjust the DMX address by pressing UP or DOWN button 3 Press ENTER to confirm or pressing MODE ESC to return to main menu Cd SL HLI Slave setting With this function you can define the device as slave 1 Select SLAV by pressing UP or DOWN button 2 Press ENTER the display shows ON or OFF 3 Press UP to select ON if you wish to enable this function or press DOWN to select OFF if you don t 4 Press ENTER to confirm or press MODE ESC to return to main menu zy XM471 V1 0 NR Pet T Mx address setting via controller With this function you can adjust the desired DM X address via an external controller This function can only be activated when the DMX value of all other channels is set to 0 on the controller Select RDMX by pressing UP or DOWN Press ENTER the display shows ON or OFF Press UP to select ON if you wish to enable this function or DOWN
4. menu CLEE ei Clear fixture time With this function you can clear the running time of the device 1 Select CLFE by pressing UP or DOWN button 2 Press ENTER the display shows ON or OFF The code is 838 3 Press UP to select ON if you wish to enable this function or press DOWN button to OFF if you don t 4 Press ENTER to confirm or Press MODE ESC to return to the main menu ee C I 5 0 1 5 98 co IEL iia sasa rii eC Uus c95 l Press MODE ESC to enter the main menu display flashing 2 Press UP or DOWN button to select EDIT T3 c 3 LI DO DE DOT ULL gt BG y LJLILJ Lc e55 SEE F Define the number of steps in Run Mal Ma ui wy Un un With this function you can define the number of steps in the Program 000 1 999 9 Run oes 1 Select STEP by pressing UP or DOWN button CNIDIIS 2 Press ENTER the display shows S XX X stands for the SL HB C00L 4090 255 total amount of steps you want to save so you can call up to 48 uti DLL c55 scenes in RUN For example if the XX is 05 it means that ECTiP Lud 255 RUN will run the first 5 scenes you saved in EDIT tcr BUD 255 3 Press ENTER to confirm or Press MODE ESC to return to i AGG 255 the main menu s S XM471 V1 0 NR cr re L Auto Save Wi
5. 471 V1 0 NR CAUTION Before taking into operation for the first time the installation has to be approved by an expert Cautions The effect should be installed outside areas where persons may reach it walk by or be seated CAUTION When installing the device make sure there is no highly inflammable material within a distance of min 0 3m Overhead mounting requires extensive experience including amongst others calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury CAUTION The electric connection must only be carried out by a qualified electrician Before mounting make sure that the installation area can hold a minimum point load of 10 times the device s weight Connect the fixture to the mains with the power plug Overhead rigging Screw the bolt of the clamp into the hold of the bracket and tighten the screw underneath Pull the safety rope through the holes on the bracket of the base and over the trussing system or a safe fixation spot Insert the end in the carabine and tighten the safety screw f XM471 V1 0 NR DMX 512 control connection Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the LED light
6. 471 V1 0 NR You can set the same starting address for all fixtures or a group of fixtures or make different address for each fixture individually If you set the same address all the units will start to listen to the same control signal from the same channel number In other words changing the settings of one channel will affect all the fixtures simultaneously If you set a different address each unit will start to listen to the channel number you have set based on the quantity of control channels of the unit That means changing the settings of one channel will affect only the selected fixture In the case of the led lighting which is 6 channels fixture when you select the standard channel mode you should set the starting address of the first unit to 1 the second unit to 7 6 1 the third unit to 13 6 7 and so on Control Board The Control Board offers several features you can simply set the starting address switch on and off the lamp run the pre programmed program or make a reset The main menu is accessed by pressing the Menu button until the display starts flashing Browse through the menu by pressing the Up button or Down button Press the Enter button in order to select the desired menu You can change the selection by pressing the Up button or Down button Confirm every selection by pressing the Enter button You can leave every mode by pressing the Menu button The functions provided are described in the follo
7. CE Features e DMX channel 6 channels Equipped with 36 x3 W LEDS 12 x Cool White 24 x Warm White 100 000 hours LED life The LEDS can be controlled individually Automatic power supply adaption between 100V and 240 Volts without power selector Programmable color change speed and strobe effect 1 XM471 V1 0 NR DMX controlled operation or stand alone operation with Master Slave function Strobe effect with 1 18 flashes per second Advantages of LED technology Extremely long life low power consumption minimal heat emission defact maintenance free with brilliant light radiation DMX control via every standard DMX controller Overview ee P A mm h ATI i ce i 1 i TN 1 Housing 2 LEDS 3 Floor stand 4 Menu button 5 Up button 6 Down button 7 Enter button 8 Power input 9 DMX output 10 DMX input SAFETY INSTRUCTIONS CAUTION Be careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual XM471 V1 0 NR 12 EN important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not a
8. OXO PROFESSIONAL LED LIGHTING USER MANUAL MultiBEAM LED Variable White Zoom KEEP THIS MANUAL FOR FUTURE NEEDS C C Thank you for your patronage We are confident that our excellent products and service can satisfy you For your own safety please read this user manual carefully before installing the device CAUTION Keep this device away from rain and moisture CAUTION Unplug mains lead before opening the housing Every person involved with the installation operation and maintenance of this device has to be qualified follow the instructions of this manual consider this manual to be part of the total product keep this manual for the entire service life of the product pass this manual on to every further owner or user of the product download the latest version of the user manual from the Internet INTRODUCTION Thank you for having chosen this professional LED lighting You will see you have acquired a powerful and versatile device Unpack the device Inside the box you should find The fixture device One power cables One XLR connection cable One safety rope and this manual Ae U N Belows are the optional accessories please purchase from your local dealer if needed 1 Barn door 2 Frost filter Please check carefully that there is no damage caused by transportation Should there be any consult your dealer and don t install this device DESCRIPTION OF THE DEVI
9. cable of this device becomes damaged it has to be replaced by authorized dealers only in order to avoid hazards Should you have further questions please contact your dealer INSTALLATION This device is only constructed for a standing installation The device must only be installed absolutely planar at a vibration free oscilation free and fire resistant location Make sure that the device is installed absolutely planar by using a water level 16 XM471 V1 0 NR TECHNICAL SPECIFICATIONS Power supply AC 100V 240V 50 60Hz Power consumption max 120 W Packing dimensions 40 x 30 x 48 CM Flight case dimensions 79x76 5x60 cm Net weight 7 KGS Gross weight JOKGS carton packing 75 5 KGS flight case packing 6pcs Remark errors and omissions for every information given in this manual except All information is subject to change without prior notice 17 XM471 V1 0 NR
10. ccept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class I Therefore it is essential that the device be earthed The electric connection must carry out by qualified person The device shall only be used with rate voltage and frequency Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually Please don t project the beam onto combustible substances Fixtures cannot be installed on combustible substances keep more than 30cm distance with wall for smooth air flow so there should be no shelter for fans and ventilation for heat radiation If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by
11. e 7200K 251 255 No Function Shutter strobe 0 31 Led trun off 32 63 Led turn on 64 95 Strobe effect slow to fast 4 96 127 Led turn on 128 159 Pulse effect in sequences 160 191 Led turn on 192 223 Random strobe effect slow to fast 224 255 Led turn on General Dimming 0 255 Dimming 0 Black 255 100 Zoom 0 255 Continuous adjustment from near to far 15 XM471 V1 0 NR Instructions for installing the barn door and frost filter For this device the bar door and the frost filter can be installed separately or together I When only install the frost filter use the rotating clips on the lens cover to fix it 2 When only install the bar door loose the 2 M4 screws on the lens cover put on the bar door and tighten the screws 3 When install the bar door and frost filter together loose the 2 M4 screws put on the frost filter and the bar door one by one then tighten the screws Loose the 2 screws CLEANING AND MAINTENANCE We recommend a frequent cleaning of the device Please use a soft lint free and moistened cloth Never use alcohol or solvents CAUTION Disconnect from mains before starting maintenance operation There are no servicable parts inside the device Maintenance and service operations are only to be carried out by authorized dealers Should you need any spare parts please use genuine parts If the power supply
12. enu display flashing Press UP or DOWN button to select SET Coy EREL pee Run by no DMX With this function you can automatic run the device by no DMX l 2 3 4 Select FAIL by pressing UP or DOWN button Press ENTER the display shows OFF HOLD or AUTO Press UP or DOWN button to select OFF HOLD or AUTO the default is HOLD Press ENTER to confirm or Press MODE ESC to return to the main menu 1 XM471 V1 0 NR at Reset With this function you can reset the device via the Control Board 1 Select REST by pressing UP or DOWN button 1 Press ENTER to reset or Press MODE ESC to return to the main menu d F oa Restore factory settings With this function you can restore the factory settings of the device All settings will be set back to the default values shaded Any edited scenes will be lost 1 Select DFSE by pressing UP or DOWN button 2 Press ENTER the display shows ON or OFF 3 Press UP to select ON if you wish to enable this function or press DOWN button to OFF if you don t 4 Press ENTER to confirm or Press MODE ESC to return to the main menu Prim Power on to preserve the MANL data With this function Power on to preserve the MANL data Select POHO by pressing UP or DOWN button WY Press ENTER the display shows ON or OFF Pre
13. er scenes you can edit and save a maximum of 48 scenes 11 Press MODE ESC to exit The number of steps can be defined under STEP and the scenes can be called up under RUN b Editing via the external controller Call up the first scene in your controller now Select SC01 by pressing UP or DOWN button Press ENTER the display shows SCOI Press ENTER the display shows COOL Select CEDT by pressing UP or DOWN button Press ENTER the display shows OFF Press UP or DOWN button the display shows ON Press ENTER the display shows SC02 You successfully downloaded the first scene Adjust the Step time as described above under point 12 2S Aa AS Sh Call up the second scene in your controller now Repeat steps 5 11 until all desired scenes are downloaded Press MODE ESC to exit The number of steps can be defined under STEP and the scenes can be called up under RUN PAs XM471 V1 0 NR INSTRUCTIONS ON USE DMX channel s functions and their values 6 DMX channels i i L Cool White 0 255 CoolWhite 0 Black 255 100 Cool White Warm White 0 255 Warm White 0 Black 255 100 Warm White Color temperature 0 10 No Function 11 50 No Function 51 90 Color_temperature 3200K 3 91 130 Color temperature 4300K 131 170 Color temperature 5600K 171 210 Color temperature 6500K 211 250 Color temperatur
14. ing You can chain multiple LED lighting together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below DMX output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket 1 Ground 2 Signal 3 Signal am NITIDE aC lt DMX512 DMX controller Address 13 Address 7 Address DMX 512 connection with DMX terminator For installations where the DMX cable has to run a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 1200 EB 2 1 PIN 3 PIN2 Projector DMX starting address selection All fixtures should be given a DMX starting address when using a DMX signal so that the correct fixture responds to the correct control signals This digital starting address is the channel number from which the fixture starts to listen to the digital control information sent out from the DMX controller The allocation of this starting address is achieved by setting the correct number on the display located on the base of the device 6 XM
15. ss UP to select OFF if you don t or press DOWN button to ON if you wish to enable this function 4 Press ENTER to confirm or Press MENU to return to the main menu UEr Li Software version With this function you can display the software version of the device 1 Select VER by pressing UP or DOWN button 2 Press ENTER The display will show V XX XX stands for the version number such as the display may also show V 1 0 V 9 9 etc 3 Press ENTER to confirm or Press MODE ESC to return to the main menu nant With this function you can Manual adjust intensity 1 Select MANL by pressing UP or DOWN button 2 Press ENTER the display shows COOL WARM TEMP STRB DIMM ZOOM 3 Press UP or DOWN button to select COOL WARM TEMP STRB DIMM ZOOM Main menu 2 4 Press ENTER to confirm or Press MODE ESC to return to the main menu 12 XM471 V1 0 NR 1 Press MODE ESC to enter the main menu display flashing 2 Press UP or DOWN button to select TIME Pree LIFE Fixture running time With this function you can display the running time of the device 1 Select LIFE by pressing UP or DOWN button 2 Press ENTER the display shows XXXX X stands for the number of hours 3 Press ENTER to confirm or Press MODE ESC to return to the main
16. th this function you can automatic save the number of steps in the Program Run 1 Select REC by pressing UP or DOWN button 2 Press ENTER the display shows RE XX XX stands for the number from 1 to 400 3 Press ENTER to confirm or Press MODE ESC to return to the main menu CI l JL LI ij Editing the channels of the individual scenes _ With this function you can edit the program to be called up in Run a Editing via the Control Board Select SC01 by pressing UP or DOWN button Press ENTER the display shows SCXX X stands for the scene no to be edited Select the channel no you would like to edit by pressing UP or DOWN button Adjust the desired DMX value by pressing UP or DOWN button Press ENTER in order to edit other channels of this scene Repeat steps 3 5 until you finish setting all the DMX values for all channels of this scene Once all the channels completed the display will flash TIME Press ENTER to edit the time needed the display shows TXXX XXX stands for the time needed to run the current scene value 001 999 E g 002 means you need 0 4ms 002 0 2ms to run the current scene Adjust the desired time by pressing UP or DOWN button 9 Press ENTER to save the settings for the scene you are editing the display will change to the next scene 9 o9 m 5 automatically 10 Repeat step 3 8 to edit and oth
17. the manufacturer or his service agent or a similar qualified person in order to avoid a hazard CAUTION Never touch the device during operation The housing may heat up CAUTION Never look directly into the light source as sensitive persons may suffer an epileptic shock Please be aware that damages caused by manual modifications to the device are not subject to warranty Keep away from children and non professionals GENERAL GUIDELINES This device is a lighting effect for professional use on stages in discotheques theatres etc This fixture is only allowed to be operated with the max alternating current which stated in the technical specifications in the last page of this manual the device was designed for indoor use only XM471 V1 0 NR vs Lighting effects are not designed for permanent operation Consistent operation breaks may ensure that the device will serve you for a long time without defects Do not shake the device Avoid brute force when installing or operating the device The device shall only be used complete with its protective shield While choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust The minimum distance between light output from the projector and the illuminated surface must be more than 0 1 meter Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the
18. to select OFF if you don t Press MODE ESC to confirm Press ENTER in order to return to the main menu Program Run Master setting With the function RUN you can run the internal program You can set the number of steps under Step You can edit the individual scenes under Edit You can run the individual scenes either automatically AUTO i e with the adjusted Step Time The selection ALON means Stand Alone mode and MAST that the device is defined as master PEE rUfi Rue D RL Ori I nha HASE l Select AUTO by pressing UP or DOWN button 2 Press ENTER for selecting the desired extension menu 3 Select ALON or MAST by pressing UP or DOWN button 4 Press ENTER to confirm or Press MODE ESC to return to the main menu HISP eir Display the DMX value Reverse display Shut off LED display di amp PHURLU WM A FLIP DEUS da LOCE Hu gg LIHL Ll Display the DMX 512 value of each channel With this function you can display the DMX 512 value of each channel 1 Select VALU by pressing UP or DOWN button 2 Press ENTER to confirm the display shows D 00 In this setting the DMX adjustment of every channel will be displayed 3 Press UP or DOWN button in order to select the desired channel If you select D 12 the display will only show the DMX value of the 12 channel 4 Press ENTER to confirm or Press MODE ESC to return to the main menu 5 The
19. wing sections Locked keys as default setting when starting up press Meun key for 3 seconds to unlock The display will be locked automatically without any operations in 15 seconds 7 XM471 V1 0 NR MODE DMX address setting Slave setting Automatic Run in Stand Change DMX address via external controller Alone Automatic Run as Master Display the DMX 512 value of each channel SLAV SLAV ADDR RDMX ALON AU A RUN AUTO MAST AU M VALU DISP FAIL D ON LOCK OFF SET I P Power on topreserve the POHO ON OFF MANL data VER V 1 0 V 9 9 Software version lt COOL C XXX 000 255 WARM W XXX 000 255 MANL BUE l RBAN NAA Manual adjust intensity STRB XXX 000 255 DIMM D XXX 000 255 ZOOM gt Z XXX 000 255 LIFE 0000 9999 hours Fixture running time TIME EB ON OFE owl fixture time code is i 838 STEP S 01 S 48 Steps of Program Run REC RE XX Auto Save Scene COOL C XXX 000 255 WARM W XXX 000 255 TEMP T XXX 000 255 EDIT Edit the internal scenes SC01 STRB S XXX 000 255 SC48 DIMM D XXX 000 255 ZOOM Z XXX 000 255 TIME T XXX 001 999 Time for each scene CEDT ON OFF Edit program via controller Reverse display Shut off LED display Key lock No DMX Status Reset Restore factory settings XM471 V1 0 NR Main functions n gE sEgE Inanu E
Download Pdf Manuals
Related Search