GA-B150-HD3P - Billiger.de
Contents
1. 10 9 13 14 15 12 4 8 1 ATX 12V_2x4 10 SPDIF_O 2 ATX 11 F_USB30_1 3 CPU_FAN 12 F_USB1 F_USB2 4 SYS _FAN1 2 3 13 COMA 5 SATA3 0 4 2 3 4 5 14 LPT 6 M2 15 TPM 7 SATA EXPRESS 16 CLR_CMOS 8 F_PANEL 17 BAT 9 F_AUDIO Read the following guidelines before connecting external devices First make sure your devices are compliant with the connectors you wish to connect Before installing the devices be sure to turn off the devices and your computer Unplug the power cord from the power outlet to prevent damage to the devices After installing the device and before turning on the computer make sure the device cable has been securely attached to the connector on the motherboard 12 1 2 ATX_12V_2X4 ATX 2x4 12V Power Connector and 2x12 Main Power Connector With the use of the power connector the power supply can supply enough stable power to all the components on the motherboard Before connecting the power connector first make sure the power supply is turned off and all devices are properly installed The power connector possesses a foolproof design Connect the power supply cable to the power connector in the correct orientation2. 10 2 Power 5V T GND 3 USB DX 8 GND 4 USB DY 9 No Pin 5 USB DX 10 NC e Do not plug the IEEE 1394 bracket 2x5 pin cable into the USB 2 0 1 1 header e Prior to installing the USB bracket be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the USB bracket 13 COMA Serial Port Header The COM header can provide one serial port via an optional COM port cable For purchasing the optional COM port cable please contact the local dealer 14 LPT Parallel Port Header The LPT header can provide one parallel port via an optional LPT port cable For purchasing the optional LPT port cable please contact the local dealer 25 1 26 2 15 TPM Trusted Platform Module Header Pin No Definition Pin No Definition 1 NDCD 6 NDSR 2 NSIN 7 NRTS 3 NSOUT 8 NCTS 4 NDTR 9 NRI 5 GND 10 No Pin You may connect a TPM Trusted Platform Module to this header 19 1 20 2 Pin No Definition Pin No Definition 1 STB 14 GND 2 AFD 15 PD6 3 PDO 16 GND 4 ERR 17 PD7 5 PD1 18 GND 6 INIT 19 ACK T PD2 20 GND 8 SLIN 21 BUSY 9 PD3 22 GND 10 GND 23 PE 11 PD4 24 No Pin 12 GND 25 SLCT 13 PD5 26 GND Pin No Definition Pin No Definition 1 LCLK 11 LADO 2 GND 12 GND 3 LFRAME 13 NC 4 No Pin 14 NC 5 LRESET 15 SB3V 6 NC 16 S
3. The 12V power connector mainly supplies power to the CPU If the 12V power connector is not connected the computer will not start To meet expansion requirements it is recommended that a power supply that can withstand high power consumption be used 500W or greater If a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system E ATX_12V_2X4 ATX_12V_ 2X4 Pin No Definition Pin No Definition 1 GND Only for 2x4 pin 5 12V Only for 2x4 pin 12V 12V 2 GND Only for 2x4 pin 6 12V Only for 2x4 pin 12V 12V 3 GND 7 12V 4 GND 8 12V ATX Pin No Definition Pin No Definition 1 3 3V 13 3 3V 2 3 3V 14 12V 3 GND 15 GND 4 5V 16 PS_ON soft On Off 5 GND 17 GND 6 5V 18 GND 7 GND 19 GND 8 Power Good 20 NC 9 5VSB stand by 5V 21 5V 10 12V 22 5V 11 12V Only for 2x12 pin 23 5V Only for 2x12 pin ATX ATX 12 3 3V Only for 2x12 pin 24 GND Only for 2x12 pin ATX ATX 3 4 CPU_FAN SYS_FAN1 2 3 Fan Headers 5 The motherboard has a 4 pin CPU fan header CPU_FAN two 4 pin SYS_FAN1 SYS_FAN2 and a 3 pin SYS_FAN3 system fan headers Most fan headers possess a foolproof insertion design When connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire The speed control function requires t
4. ae 2 7 Power Management GIGABYTE UEFI DualBlOS System BIOS Power n S Information Features Peripherals Management Save amp Exit English Q F lash Select Screen Tl Select Item en FAT16 32 Format Only AC BACK Determines the state of the system after the return of power from an AC power loss gt gt Always Off The system stays off upon the return of the AC power Default gt gt Always On The system is turned on upon the return of the AC power gt gt Memory The system returns to its last known awake state upon the return of the AC power Power On By Keyboard Allows the system to be turned on by a PS 2 keyboard wake up event Note To use this function you need an ATX power supply providing at least 1A on the 5VSB lead gt Disabled Disables this function Default gt Password Set a password with 1 5 characters to turn on the system gt Keyboard 98 Press POWER button on the Windows 98 keyboard to turn on the system gt gt Any Key Press any key to turn on the system Power On Password Set the password when Power On By Keyboard is set to Password Press lt Enter gt on this item and set a password with up to 5 characters and then press lt Enter gt to accept To turn on the system enter the password and press lt Enter gt Note To cancel the password press lt Enter gt on this item When prompted for the password press lt Enter gt again without entering the password to clear the p
5. iTE I O Controller Chip Hardware Monitor gt gt System voltage detection CPU System temperature detection CPU System fan speed detection CPU System overheating warning CPU System fan fail warning CPU System fan speed control Whether the fan speed control function is supported will depend on the cooler you install 2 x 128 Mbit flash Use of licensed AMI UEFI BIOS Support for DualBIOS PnP 1 0a DMI 2 7 WfM 2 0 SM BIOS 2 7 ACPI 5 0 BIOS Ss gt Unique Features Support for APP Center Available applications in APP Center may vary by motherboard model Supported functions of each application may also vary depending on motherboard specifications 3D OSD BIOS AutoGreen Cloud Station EasyTune Easy RAID Fast Boot Smart TimeLock Smart Keyboard Smart Backup System Information Viewer USB Blocker Support for Q Flash Support for Smart Switch Support for Xpress Install Norton Internet Security OEM version Intel Small Business Advantage cFosSpeed H Bundled Software Operating Support for Windows 10 8 1 64 bit System Support for Windows 7 32 bit 64 bit Please download the Windows USB Installation Tool from GIGABYTE s website and install it before installing Windows 7 fim Form Factor e ATX Form Factor 30 5cm x 21 4cm GIGABYTE reserves the right to make any chan
6. 99 2 6 Chipset GIGABYTE UEFI DuaIBIOS System BIOs Power HIT Information Features Peripherals Chipset Management English O VT d Note Enables or disables Intel Virtualization Technology for Directed I O Default Disabled gt Internal Graphics Enables or disables the onboard graphics function Default Auto DVMT Pre Allocated Allows you to set the onboard graphics memory size Options are 32M 512M Default 64M lt DVMT Total Gfx Mem Allows you to allocate the DVMT memory size of the onboard graphics Options are 128M 256M MAX Default 256M Audio Controller Enables or disables the onboard audio function Default Enabled If you wish to install a 3rd party add in audio card instead of using the onboard audio set this item to Disabled Audio DSP Enables or disables the DSP functionality of the PCH audio unit Default Disabled PCH LAN Controller Enables or disables the onboard LAN function Default Enabled If you wish to install a 3rd party add in network card instead of using the onboard LAN set this item to Disabled lt Wake on LAN Enables or disables the wake on LAN function Default Enabled High Precision Timer Enables or disables High Precision Event Timer HPET in the operating system Default Enabled Note This item is present only when you install a CPU that supports this feature For more information about Intel CPUs unique features please visit Intel s website
7. Save amp Exit Setup Press lt Enter gt on this item and select Yes This saves the changes to the CMOS and exits the BIOS Setup program Select No or press lt Esc gt to return to the BIOS Setup Main Menu Exit Without Saving Press lt Enter gt on this item and select Yes This exits the BIOS Setup without saving the changes made in BIOS Setup to the CMOS Select No or press lt Esc gt to return to the BIOS Setup Main Menu Load Optimized Defaults Press lt Enter gt on this item and select Yes to load the optimal BIOS default settings The BIOS defaults settings help the system to operate in optimum state Always load the Optimized defaults after updating the BIOS or after clearing the CMOS values Boot Override Allows you to select a device to boot immediately Press lt Enter gt on the device you select and select Yes to confirm Your system will restart automatically and boot from that device Save Profiles This function allows you to save the current BIOS settings to a profile You can create up to 8 profiles and save as Setup Profile 1 Setup Profile 8 Press lt Enter gt to complete Or you can select Select File in HDD FDD USB to save the profile to your storage device Load Profiles If your system becomes unstable and you have loaded the BIOS default settings you can use this function to load the BIOS settings from a profile created before without the hassles of reconfiguring the BIOS settings First select the profile you
8. Set to External TPM2 0 if you install an Infineon TPM 2 0 module optional Default PTT Device Select Allows you to select whether to support TPM 1 2 or TPM 2 0 device Auto lets the BIOS automatically configure this setting Default Auto Super IO Configuration Serial Port 1 Enables or disables the onboard serial port Default Enabled Parallel Port Enables or disables the onboard parallel port Default Enabled Intel R Bios Guard Technology Enables or disables the Intel BIOS Guard feature which protects the BIOS from malicious attacks SATA Configuration SATA Controller s Enables or disables the integrated SATA controllers Default Enabled SATA Mode Selection gt gt AHCI Configures the SATA controllers to AHCI mode Advanced Host Controller Interface AHCI is an interface specification that allows the storage driver to enable advanced Serial ATA features such as Native Command Queuing and hot plug Default Aggressive LPM Support Enables or disables the power saving feature ALPM Aggressive Link Power Management for the Chipset SATA controllers Default Enabled Port 0 1 2 3 4 5 Enables or disables each SATA port Default Enabled Hot plug Enables or disable the hot plug capability for each SATA port Default Disabled External SATA Enables or disables support for external SATA devices Default Disabled NVMe Configuration Displays information on your M 2 NVME PCle SSD if installed
9. 9338 626 854 9326 hereby declares that the product Product Name Motherboard Model Number GA B150 HD3P Conforms to the following specifications FCC Part 15 Subpart B Section 15 107 a and Section 15 109 a Class B Digital Device Supplementary Information This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful and 2 this device must accept any inference received including that may cause undesired operation Representative Person s Name ERIC LU Signature Eric Lu Date Sept 17 2015 2015 GIGA BYTE TECHNOLOGY CO LTD All rights reserved The trademarks mentioned in this manual are legally registered to their respective owners Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice No part of this manual may be reproduced copied translated transmitted or published in any form or by any means without GIGABYTE s prior written permission W In order to assist in the use of this product carefully read the User s Manual m For product related information check on our website at http www gigabyte com Identifying Your Motherboard Revision The revision number on your motherboard looks like this REV X X For example REV 1 0 means the revision of the motherboard i
10. DDR4_1 DDR4_3 gt gt Dual Channel Memory Configurations Table DDR4_4 DDR4_2 DDR4_3 DDR4_1 2 Modules DS SS DS SS DS SS DS SS 4 Modules DS SS DS SS DS SS DS SS SS Single Sided DS Double Sided No Memory Due to CPU limitations read the following guidelines before installing the memory in Dual Channel mode 1 Dual Channel mode cannot be enabled if only one memory module is installed 2 When enabling Dual Channel mode with two or four memory modules it is recommended that memory of the same capacity brand speed and chips be used and installed in the same colored sockets 1 5 Installing an Expansion Card Read the following guidelines before you begin to install an expansion card A e Make sure the motherboard supports the expansion card Carefully read the manual that came with your expansion card e Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage 1 6 Back Panel Connectors USB 2 0 1 1 Port The USB port supports the USB 2 0 1 1 specification Use this port for USB devices PS 2 Keyboard Mouse Port Use this port to connect a PS 2 mouse or keyboard D Sub Port The D Sub port supports a 15 pin D Sub connector and supports a maximum resolution of 1920x1200 60 Hz the actual resolutions supported depend on the monitor being used Connect a monitor that supports D Sub connecti
11. Express SATA connectors and PCIEX4 slot she A USB Chipset 5x USB 3 0 2 0 ports 3 ports on the back panel 2 ports available through the internal USB header 6x USB 2 0 1 1 ports 2 ports on the back panel 4 ports available through the internal USB headers Chipset Intel USB3 1 Controller 1X USB Type C port on the back panel with USB 3 1 support 1x USB 3 1 Type A port red on the back panel sce Internal go l Connectors w Back Panel ty a Connectors I O Controller gt gt gt gt gt gt o o ooo o o gt gt gt 1 x 24 pin ATX main power connector 1 x 8 pin ATX 12V power connector 1 x M 2 Socket 3 connector 1 x SATA Express connector 6 x SATA 6Gb s connectors 1 x CPU fan header 3 x system fan headers 1 x front panel header 1 x front panel audio header 1 x USB 3 0 2 0 header 2 x USB 2 0 1 1 headers 1 x Thunderbolt add in card connector 1 x serial port header 1 x parallel port header 1 x Trusted Platform Module TPM header 1 x S PDIF Out header 1 x Clear CMOS jumper 1 x PS 2 keyboard mouse port 1 x D Sub port 1 x DVI D port 1 x USB Type C Port with USB 3 1 support 1 x USB 3 1 Type A port red 1 x HDMI port 3 x USB 3 0 2 0 ports 2 x USB 2 0 1 1 ports 1 x RJ 45 port 6 x audio jacks Center Subwoofer Speaker Out Rear Speaker Out Side Speaker Out Line In Line Out Mic In
12. enable the legacy option ROM for the LAN controller Default Disabled This item is configurable only when CSM Support is set to Enabled 29 Storage Boot Option Control Allows you to select whether to enable the UEFI or legacy option ROM for the storage device controller gt gt Disabled Disables option ROM gt gt UEFI Only Enables UEFI option ROM only gt gt Legacy Only Enables legacy option ROM only Default This item is configurable only when CSM Support is set to Enabled Other PCI Device ROM Priority Allows you to select whether to enable the UEFI or Legacy option ROM for the PCI device controller other than the LAN storage device and graphics controllers gt gt Disabled Disables option ROM gt gt UEFI Only Enables UEFI option ROM only Default gt gt Legacy Only Enables legacy option ROM only This item is configurable only when CSM Support is set to Enabled Network Stack Disables or enables booting from the network to install a GPT format OS such as installing the OS from the Windows Deployment Services server Default Disabled Ipv6 PXE Support Enables or disables IPv6 PXE Support This item is configurable only when Network Stack is enabled lpv4 PXE Support Enables or disables IPv4 PXE Support This item is configurable only when Network Stack is enabled Administrator Password Allows you to configure an administrator password Press lt Enter gt on this item type the password and
13. is on a aa lt S3 S4 S5 Off when the system is operating The LED is a GLLH off when the system is in S3 S4 sleep state 50 or powered off S5 49 PW Power Switch Red Connects to the power switch on the chassis front panel You may configure the way to turn off your system using the power switch refer to Chapter 2 BIOS Setup Power Management for more information ST e SPEAK Speaker Orange Connects to the speaker on the chassis front panel The system reports system startup status by issuing a beep code One single short beep will be heard if no problem is detected at system startup e HD Hard Drive Activity LED Blue Connects to the hard drive activity LED on the chassis front panel The LED is on when the hard drive is reading or writing data e RES Reset Switch Green Connects to the reset switch on the chassis front panel Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart e Cl Chassis Intrusion Header Gray Connects to the chassis intrusion switch sensor on the chassis that can detect if the chassis cover has been removed This function requires a chassis with a chassis intrusion switch sensor e NC Orange No Connection The front panel design may differ by chassis A front panel module mainly consists of power switch EB reset switch power LED hard drive activity LED speaker and etc When connecting your chassis front panel module to this hea
14. lets the BIOS automatically configure this setting and sets the voltage following Intel s specifications Default Auto CPU Core Voltage Control This section provides CPU voltage control options gt Chipset Voltage Control This section provides Chipset voltage control options 24 gt DRAM Voltage Control This section provides memory voltage control options gt Internal VR Control This section provides VR voltage control options gt EF PC Health Status Reset Case Open Status gt Disabled Keeps or clears the record of previous chassis intrusion status Default gt gt Enabled Clears the record of previous chassis intrusion status and the Case Open field will show No at next boot Case Open Displays the detection status of the chassis intrusion detection device attached to the motherboard Cl header If the system chassis cover is removed this field will show Yes otherwise it will show No To clear the chassis intrusion status record set Reset Case Open Status to Enabled save the settings to the CMOS and then restart your system CPU Vcore CPU VCCSA DRAM Channel A B Voltage 3 3V 5V 12V CPU VAXG Displays the current system voltages CPU System Temperature Displays current CPU system temperature CPU System FAN Speed Displays current CPU system fan speeds CPU System Temperature Warning Sets the warning threshold for CPU system temperature When temperature exceeds the thr
15. the computer system in a high temperature or wet environment Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user If you are uncertain about any installation steps or have a problem related to the use of the product please consult a certified computer technician If you use an adapter extension power cable or power strip ensure to consult with its installation and or grounding instructions y CPU Support for Intel Core i7 processors Intel Core i5 processors Intel Core i3 processors Intel Pentium processors Intel Celeron processors in the LGA1151 package Go to GIGABYTE s website for the latest CPU support list L3 cache varies with CPU Q Chipset Intel B150 Express Chipset Memory 4 x DDR4 DIMM sockets supporting up to 64 GB of system memory Due to a Windows 32 bit operating system limitation when more than 4 GB of physical memory is installed the actual memory size displayed will be less than the size of the physical memory installed Dual channel memory architecture Support for DDR4 2133 MHz memory modules Support for ECC UDIMM 1Rx8 2Rx8 memory modules operate in non ECC mode Support for non ECC UDIMM 1Rx8 2Rx8 1Rx16 memory modules Go to GIGABYTE s website for the latest supported memory speeds and memory modules Onboard Graphics Int
16. then press lt Enter gt You will be requested to confirm the password Type the password again and press lt Enter gt You must enter the administrator password or user password at system startup and when entering BIOS Setup Differing from the user password the administrator password allows you to make changes to all BIOS settings User Password Allows you to configure a user password Press lt Enter gt on this item type the password and then press lt Enter gt You will be requested to confirm the password Type the password again and press lt Enter gt You must enter the administrator password or user password at system startup and when entering BIOS Setup However the user password only allows you to make changes to certain BIOS settings but not all To cancel the password press lt Enter gt on the password item and when requested for the password enter the correct one first When prompted for a new password press lt Enter gt without entering any password Press lt Enter gt again when prompted to confirm NOTE Before setting the User Password be sure to set the Administrator Password first 30 2 5 Peripherals GIGABYTE UEF DualBloS BIOS Power He Information Features Peripherals Chipset Management Save amp Exit English Q F lash Intel Platform Trust Technology PTT Disabled Select Item en FAT16 32 Format Only Intel Platform Trust Technology PTT Enables or disables Intel PTT Technolo
17. will automatically reduce the core frequency in order to reduce the current Auto sets the power limit according to the CPU specifications Default Auto No of CPU Cores Enabled Allows you to select the number of CPU cores to enable in an Intel multi core CPU the number of CPU cores may vary by CPU Auto lets the BIOS automatically configure this setting Default Auto Hyper Threading Technology Allows you to determine whether to enable multi threading technology when using an Intel CPU that supports this function This feature only works for operating systems that support multi processor mode Auto lets the BIOS automatically configure this setting Default Auto CPU Enhanced Halt C1E Enables or disables Intel CPU Enhanced Halt C1E function a CPU power saving function in system halt state When enabled the CPU core frequency and voltage will be reduced during system halt state to decrease power consumption Auto lets the BIOS automatically configure this setting Default Auto C3 State Support te Allows you to determine whether to let the CPU enter C3 mode in system halt state When enabled the CPU core frequency and voltage will be reduced during system halt state to decrease power consumption The C3 state is a more enhanced power saving state than C1 Auto lets the BIOS automatically configure this setting Default Auto C6 C7 State Support t Allows you to determine whether to let the CPU ente
18. wish to load and then press lt Enter gt to complete You can select Select File in HDD FDD USB to input the profile previously created from your storage device or load the profile automatically created by the BIOS such as reverting the BIOS settings to the last settings that worked properly last known good record 36 Chapter 3 Appendix Drivers Installation e Before installing the drivers first install the operating system The following instructions use Windows FB 8 1 as the example operating system e After installing the operating system insert the motherboard driver disk into your optical drive Click on the message Tap to choose what happens with this disc on the top right corner of the screen and select Run Run exe Or go to My Computer double click the optical drive and execute the Run exe program Xpress Install will automatically scan your system and then list all of the drivers that are recommended to install You can click the Xpress Install button and Xpress Install will install all of the selected drivers Or click the arrow J icon to individually install the drivers you need 5 GIGABYTE Xpress Install We recommend that you install the drivers and software listed below for your motherboard Please click Xpress 4 Drivers amp Install to install all the drivers automatically Software Click the D button on the right of an application to install it M Google Drive Google Chrome R a faste
19. ERIRQ 7 LAD3 17 GND 8 LAD2 18 NC 9 VCC3 19 NC 10 LAD 20 SUSCLK 18 16 CLR_CMOS Clear CMOS Jumper Use this jumper to clear the BIOS configuration and reset the CMOS values to factory defaults To clear the CMOS values use a metal object like a screwdriver to touch the two pins for a few seconds CIJ Open Normal O Short Clear CMOS Values the CMOS values e After system restart go to BIOS Setup to load factory defaults select Load Optimized Defaults or manually configure the BIOS settings refer to Chapter 2 BIOS Setup for BIOS configurations h e Always turn off your computer and unplug the power cord from the power outlet before clearing 17 BAT Battery The battery provides power to keep the values such as BIOS configurations date and time information in the CMOS when the computer is turned off Replace the battery when the battery voltage drops to a low level or the CMOS values may not be accurate or may be lost You may clear the CMOS values by removing the battery 1 Turn off your computer and unplug the power cord 2 Gently remove the battery from the battery holder and wait for one minute Or use a metal object like a screwdriver to touch the positive and negative terminals of the battery holder making them short for 5 seconds 3 Replace the battery 4 Plug in the power cord and restart your computer e Always turn off your computer and unplug the power cord before re
20. GA B150 HD3P User s Manual Rev 1001 Ops J 1 ae F l J sre For more product details please visit GIGABYTE s website ORE i a To reduce the impacts on global warming the packaging materials of this product are recyclable and reusable GIGABYTE works with you to protect the environment Declaration of Conformity We Manufacturer Importer G B T Technology Trading GMbH Address Bullenkoppel 16 22047 Hamburg Germany Declare that the product Product Type Motherboard Product Name GA B150 HD3P conforms with the essential requirements of the following directives I 2004 108 EC EMC Directive KX Conduction amp Radiated Emissions EN 55022 2010 XX Immunity EN 55024 2010 EN 61000 3 2 2006 A2 2009 EN 61000 3 3 2008 KX Power line harmonics IX Power line flicker I 2006 95 EC LVD Directive XX Safety EN60950 1 2006 A12 2011 XX 2011 65 EU RoHS Directive XX Restriction of use of certain This product does not contain any of the restricted substances in electronic equipment substances listed in Annex Il in concentrations and applications banned by the directive CE CE marking Signature Timmy Huang Stamp Date Sept 17 2015 Name Timmy Huang Copyright DECLARATION OF CONFORMITY Per FCC Part 2 Section 2 1077 a C Responsible Party Name G B T INC U S A Address 17358 Railroad Street City of Industry CA 91748 Phone Fax No 626 854
21. LED Connection Speed LED Activity LED Stale Description State Description a Orange 1 Gbps data rate Blinking Data transmission or receiving is occurring Green 100 Mbps data rate On No data transmission or receiving is occurring On 10 Mbps data rate LAN Port Center Subwoofer Speaker Out Orange Use this audio jack to connect center subwoofer speakers in a 5 1 7 1 channel audio configuration Rear Speaker Out Black Use this audio jack to connect rear speakers in a 4 5 1 7 1 channel audio configuration Side Speaker Out Gray Use this audio jack to connect side speakers in a 7 1 channel audio configuration Line In Blue The line in jack Use this audio jack for line in devices such as an optical drive walkman etc Line Out Green The line out jack Use this audio jack for a headphone or 2 channel speaker This jack can be used to connect front speakers in a 4 5 1 7 1 channel audio configuration Mic In Pink The Mic in jack FB Please visit GIGABYTE s website for more software information When removing the cable connected to a back panel connector first remove the cable from your device and then remove it from the motherboard When removing the cable pull it straight out from the connector Do not rock it side to side to prevent an electrical short inside the cable connector 1 7 Internal Connectors
22. aeee Y b Alignment Alignment j Key i Pag Pin One Corner of the CPU Socket Triangle Pin One Marking on the CPU A Do not remove the CPU socket cover before inserting the CPU It may pop off from the load plate automatically during the process of re engaging the lever after you insert the CPU 1 4 Installing the Memory Read the following guidelines before you begin to install the memory A e Make sure that the motherboard supports the memory It is recommended that memory of the same capacity brand speed and chips be used Go to GIGABYTE s website for the latest supported memory speeds and memory modules e Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage e Memory modules have a foolproof design A memory module can be installed in only one direction If you are unable to insert the memory switch the direction Dual Channel Memory Configuration This motherboard provides four memory sockets and supports Dual Channel Technology After the memory is installed the BIOS will automatically detect the specifications and capacity of the memory Enabling Dual Channel memory mode will double the original memory bandwidth Please visit GIGABYTE s website for details on hardware installation sO The four memory sockets are divided into two channels and each channel has two memory sockets as following gt gt Channel A DDR4_2 DDR4_4 gt Channel B
23. ance Default Disabled 26 2 3 System Information GIGABYTE UEFI DualBloS System BIOS Power Hotei Information Features Peripherals Chipset Management Save amp Exit English Q F lash System Information Model Name BIOS Version BIOS Date BIOS ID Administrator Select Screen TL Select Item This section provides information on your motherboard model and BIOS version You can also select the default language used by the BIOS and manually set the system time CH System Language Selects the default language used by the BIOS System Date Sets the system date The date format is week read only month date and year Use lt Enter gt to switch between the Month Date and Year fields and use the lt Page Up gt or lt Page Down gt key to set the desired value System Time Sets the system time The time format is hour minute and second For example 1 p m is 13 00 00 Use lt Enter gt to switch between the Hour Minute and Second fields and use the lt Page Up gt or lt Page Down gt key to set the desired value Access Level Displays the current access level depending on the type of password protection used If no password is set the default will display as Administrator The Administrator level allows you to make changes to all BIOS settings the User level only allows you to make changes to certain BIOS settings but not all IT BIOS Features GIGABYTE UEFI DualBloS Syste
24. and time as following gt gt Wake up day Turn on the system at a specific time on each day or on a specific day in a month gt gt Wake up hour minute second Set the time at which the system will be powered on automatically Note When using this function avoid inadequate shutdown from the operating system or removal of the AC power or the settings may not be effective RC6 Render Standby Allows you to determine whether to let the onboard graphics enter standby mode to decrease power consumption Default Enabled Platform Power Management Enables or disables the Active State Power Management function ASPM Default Disabled PEG ASPM Allows you to configure the ASPM mode for the device connected to the CPU PEG bus This item is configurable only when Platform Power Management is set to Enabled Default Enabled PCH ASPM Allows you to configure the ASPM mode for the device connected to Chipset s PCI Express bus This item is configurable only when Platform Power Management is set to Enabled Default Enabled DMI Link ASPM Control Allows you to configure the ASPM mode for both CPU side and Chipset side of the DMI link This item is configurable only when Platform Power Management is set to Enabled Default Enabled 35 2 8 Save amp Exit GIGABYTE UEFI DualBloS System BIOS Power ilo ln Information Features Peripherals Chipset Management Save amp Exit English Q F lash Boot Override Select Item
25. assword settings Power On By Mouse Allows the system to be turned on by a PS 2 mouse wake up event Note To use this function you need an ATX power supply providing at least 1A on the 5VSB lead gt Disabled Disables this function Default gt gt Move Move the mouse to turn on the system gt gt Double Click Double click on left button on the mouse to turn on the system 34 ErP Determines whether to let the system consume least power in S5 shutdown state Default Disabled Note When this item is set to Enabled the following functions will become unavailable Resume by Alarm PME event wake up power on by mouse power on by keyboard and wake on LAN Soft Off by PWR BTTN Configures the way to turn off the computer in MS DOS mode using the power button gt gt Instant Off Press the power button and then the system will be turned off instantly Default gt gt Delay 4 Sec Press and hold the power button for 4 seconds to turn off the system If the power button is pressed for less than 4 seconds the system will enter suspend mode Power Loading Enables or disables dummy load When the power supply is at low load a self protection will activate causing it to shutdown or fail If this occurs please set to Enabled Auto lets the BIOS automatically configure this setting Default Auto Resume by Alarm Determines whether to power on the system at a desired time Default Disabled lf enabled set the date
26. aving Enabled allows the system to simultaneously access different ranks of the memory to increase memory performance and stability Auto lets the BIOS automatically configure this setting Default Auto IMC Timing Settings This sub menu provides options for tuning memory compatibility and stability gt Channel A B Memory Sub Timings This sub menu provides memory timing settings for each channel of memory This sub menu provides memory timing settings for each channel of memory The respective timing setting screens are configurable only when Memory Timing Mode is set to Manual or Advanced Manual Note Your system may become unstable or fail to boot after you make changes on the memory timings If this occurs please reset the board to default values by loading optimized defaults or clearing the CMOS values gt gt Cr gt Advanced Voltage Settings Advanced Power Settings CPU Vcore Loadline Calibration Allows you to configure Load Line Calibration for the CPU Vcore voltage Selecting a higher level keeps the CPU Vcore voltage more consistent with what is set in BIOS under heavy load Auto lets the BIOS automatically configure this setting and sets the voltage following Intel s specifications Default Auto VAXG Loadline Calibration Allows you to configure Load Line Calibration for the CPU VAXG voltage Selecting a higher level keeps the CPU VAXG voltage more consistent with what is set in BIOS under heavy load Auto
27. bove are synchronous to those under the same items on the Advanced Frequency Settings menu 21 Uncore Ratio Allows you to set the CPU Uncore ratio The adjustable range is dependent on the CPU being used Uncore Frequency Displays the current CPU Uncore frequency CPU Flex Ratio Override Enables or disables the CPU Flex Ratio The maximum CPU clock ratio will be based on the CPU Flex Ratio Settings value if CPU Clock Ratio is set to Auto Default Disabled CPU Flex Ratio Settings Allows you to set the CPU Flex Ratio The adjustable range may vary by CPU Default 20 Intel R Turbo Boost Technology Allows you to determine whether to enable the Intel CPU Turbo Boost technology Auto lets the BIOS automatically configure this setting Default Auto Turbo Ratio Allows you to set the CPU Turbo ratios for different number of active cores Auto sets the CPU Turbo ratios according to the CPU specifications Default Auto Power Limit TDP Watts Power Limit Time Allows you to set the power limit for CPU Turbo mode and how long it takes to operate at the specified power limit If the specified value is exceeded the CPU will automatically reduce the core frequency in order to reduce the power Auto sets the current limit according to the CPU specifications Default Auto Core Current Limit Amps Allows you to set a current limit for CPU Turbo mode When the CPU current exceeds the specified current limit the CPU
28. d nut from the motherboard Locate the proper mounting hole for the M 2 SSD to be installed and then screw the nut first Step 2 Slide the M 2 SSD into the connector at an angle Step 3 Press the M 2 SSD down and then secure it with the screw On the motherboard there are three length adjustment holes for the M 2 SSD Select the proper hole for the M 2 SSD to be installed and refasten the screw and nut gt gt When installing different types of M 2 SSDs including SATA SSDs PCle x4 SSDs and PCle x2 SSDs be sure to refer to the supported configurations in the tables below according to the operating mode of your SATA controller Connector SATA3_0 SATA3_ 1 SATA3_2 SATA3_3 SATA3_4 SATA3_5 SATA Express PCIEX4 Type of SSD SATA SSD PCle x4 SSD PCle x2 SSD ME No SSDs Installed v Supported X Not supported NA No devices installed 7 SATA EXPRESS SATA Express Connectors Each SATA Express connector supports a single SATA Express device Note The PCIEX4 runs at x1 speed 8 F_PANEL Front Panel Header Connect the power switch reset switch speaker chassis intrusion switch sensor and system status indicator on the chassis to this header according to the pin assignments below Note the positive and negative pins before connecting the cables e PLED PWR_LED Power LED Yellow Purple System Status LED Connects to the power status indicator H SO On on the chassis front panel The LED
29. der make sure the wire assignments and the pin assignments are matched correctly 9 F_AUDIO Front Panel Audio Header The front panel audio header supports Intel High Definition audio HD and AC 97 audio You may connect your chassis front panel audio module to this header Make sure the wire assignments of the module connector match the pin assignments of the motherboard header Incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it PWR_LED PWR_LED PWR_LED For HD Front Panel Audio For AC 97 Front Panel Audio Pin No Definition Pin No Definition Pin No Definition Pin No Definition 9 1 1 MIC2_L 6 Sense 1 MIC 6 NC i 2 GND i FAUDIO_JD 2 GND 7 NC 3 MIC2_R 8 No Pin 3 MIC Power 8 No Pin 1 4 ACZDET 9 LINE2L 4 NC 9 Line Out L 5 LINE2_R 10 Sense 5 Line Out R 10 NC e The front panel audio header supports HD audio by default EB e Audio signals will be present on both of the front and back panel audio connections simultaneously e Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug For information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer 16 10 SPDIF_O S PDIF Out Header This header supports digital S PDIF Ou
30. dministrator Password User Password item gt gt Setup A password is only required for entering the BIOS Setup program gt gt System Apassword is required for booting the system and for entering the BIOS Setup program Default Full Screen LOGO Show Allows you to determine whether to display the GIGABYTE Logo at system startup Disabled skips the GIGABYTE Logo when the system starts up Default Enabled 28 Fast Boot Enables or disables Fast Boot to shorten the OS boot process Ultra Fast provides the fastest bootup speed Default Disabled SATA Support gt All Sata Devices All SATA devices are functional in the operating system and during the POST Default gt gt Last Boot HDD Only Except for the previous boot drive all SATA devices are disabled before the OS boot process completes This item is configurable only when Fast Boot is set to Enabled or Ultra Fast VGA Support Allows you to select which type of operating system to boot gt gt Auto Enables legacy option ROM only gt gt EFI Driver Enables EFI option ROM Default This item is configurable only when Fast Boot is set to Enabled or Ultra Fast USB Support gt gt Disabled All USB devices are disabled before the OS boot process completes gt gt Full Initial All USB devices are functional in the operating system and during the POST gt gt Partial Initial Part of the USB devices are disabled before the OS boot process completes Defa
31. egrated Graphics Processor Intel HD Graphics support 1x D Sub port supporting a maximum resolution of 1920x1200 60 Hz 1x DVI D port supporting a maximum resolution of 1920x1200 60 Hz The DVI D port does not support D Sub connection by adapter 1x HDMI port supporting a maximum resolution of 4096x2160 24 Hz Support for HDMI 1 4 version Support for up to 3 displays at the same time Maximum shared memory of 512 MB Audio Realtek ALC892 codec High Definition Audio 2 4 5 1 7 1 channel Support for S PDIF Out LAN Intel GbE LAN chip 10 100 1000 Mbit X Expansion Slots 1 x PCI Express x16 slot running at x16 PCIEX16 For optimum performance if only one PCI Express graphics card is to be installed be sure to install it in the PCIEX16 slot 1 x PCI Express x16 slot running at x4 PCIEX4 The PCIEX4 slot shares bandwidth with the SATA Express slot and the M 2 connector When the SATA Express slot or the M 2 connector is populated the PCIEX4 slot will operate at up to x1 mode 1 x PCI Express x1 slot All of the PCI Express slots conform to PCI Express 3 0 standard 3 x PCI slots fi Multi Graphics oh Technology Support for 2 Way AMD CrossFire Technology Storage Interface Chipset 1 x M 2 Socket 3 connector 1 x SATA Express connector 6 x SATA 6Gb s connectors Refer to 1 7 Internal Connectors for the supported configurations of the M 2 SATA
32. ers are required for warranty validation Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components When connecting hardware components to the internal connectors on the motherboard make sure they are connected tightly and securely When handling the motherboard avoid touching any metal leads or connectors It is best to wear an electrostatic discharge ESD wrist strap when handling electronic components such as a motherboard CPU or memory If you do not have an ESD wrist strap keep your hands dry and first touch a metal object to eliminate static electricity Prior to installing the motherboard please have it on top of an antistatic pad or within an electrostatic shielding container Before connecting or unplugging the power supply cable from the motherboard make sure the power supply has been turned off Before turning on the power make sure the power supply voltage has been set according to the local voltage standard Before using the product please verify that all cables and power connectors of your hardware components are connected To prevent damage to the motherboard do not allow screws to come in contact with the motherboard circuit or its components Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing Do not place the computer system on an uneven surface Do not place
33. eshold BIOS will emit warning sound Options are Disabled default 60 C 140 F 70 C 158 F 80 C 176 F 90 C 194 F CPU System Fan Fail Warning Allows the system to emit warning sound if the fan is not connected or fails Check the fan condition or fan connection when this occurs Default Disabled CPU Fan Speed Control CPU_FAN Connector Allows you to determine whether to enable the fan speed control function and adjust the fan speed gt gt Normal Allows the fan to run at different speeds according to the CPU temperature You can adjust the fan speed with System Information Viewer based on your system requirements Default gt gt Silent Allows the fan to run at slow speeds gt gt Manual Allows you to control the fan speed under the Fan Speed Percentage item gt gt Full Speed Allows the fan to run at full speeds Fan Speed Percentage Allows you to control the fan speed This item is configurable only when CPU Fan Speed Control is set to Manual Options are 0 75 PWM value C 2 50 PWM value C 25 v 1st System Fan Speed Control SYS_FAN1 Connector Allows you to determine whether to enable the fan speed control function and adjust the fan speed gt gt Normal Allows the fan to run at different speeds according to the system temperature You can adjust the fan speed with System Information Viewer based on your system requirements Default gt gt Silent Allows the fan to run at slow speeds g
34. et Management Save amp Exit English Q F lash gt M I T Current Status BIOS Version BCLK CPU Frequency Memory Frequency Total Memory Size CPU Temperature Vcore This section provides information on the BIOS version CPU base clock CPU frequency memory frequency total memory size CPU temperature and CPU voltage etc system configurations Incorrectly doing overclock overvoltage may result in damage to CPU chipset or memory and reduce the useful life of these components This page is for advanced users only and we recommend you not to alter the default settings to prevent system instability or other unexpected results Inadequately altering the settings may result in system s failure to boot If this occurs clear the CMOS values and reset the board to default values M I T Current Status This screen provides information on CPU memory frequencies parameters Whether the system will work stably with the overclock overvoltage settings you made is dependent on your overall Advanced Frequency Settings Graphics Slice Ratio Allows you to set the Graphics Slice Ratio Graphics UnSlice Ratio Allows you to set the Graphics UnSlice Ratio CPU Clock Ratio Allows you to alter the clock ratio for the installed CPU The adjustable range is dependent on the CPU being installed CPU Frequency Displays the current operating CPU frequency Advanced CPU Core Settings CPU Clock Ratio CPU Frequency The settings a
35. ges to the product specifications and product related information without prior notice Please visit GIGABYTE s website for support lists of CPU memory modules SSDs and M 2 devices 1 3 Installing the CPU Read the following guidelines before you begin to install the CPU A e Make sure that the motherboard supports the CPU Go to GIGABYTE s website for the latest CPU support list e Always turn off the computer and unplug the power cord from the power outlet before installing the CPU to prevent hardware damage e Locate the pin one of the CPU The CPU cannot be inserted if oriented incorrectly Or you may locate the notches on both sides of the CPU and alignment keys on the CPU socket e Apply an even and thin layer of thermal grease on the surface of the CPU Do not turn on the computer if the CPU cooler is not installed otherwise overheating and damage of the CPU may occur e Set the CPU host frequency in accordance with the CPU specifications It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals If you wish to set the frequency beyond the standard specifications please do so according to your hardware specifications including the CPU graphics card memory hard drive etc Installing the CPU Locate the alignment keys on the motherboard CPU socket and the notches on the CPU LGA1151 CPU Socket LGA1151 CPU
36. gy Default Disabled Initial Display Output Specifies the first initiation of the monitor display from the installed PCI Express graphics card or the onboard graphics gt gt IGFX Sets the onboard graphics as the first display gt gt PCle 1 Slot Sets the graphics card on the PCIEX16 slot as the first display Default gt gt PCle 2 Slot Sets the graphics card on the PCIEX 4 slot as the first display Audio LED Enables or disables the onboard audio LED Default On Legacy USB Support Allows USB keyboard mouse to be used in MS DOS Default Enabled XHCI Hand off Determines whether to enable XHCI Hand off feature for an operating system without XHCI Hand off support Default Disabled USB Mass Storage Driver Support Enables or disables support for USB storage devices Default Enabled USB Storage Devices Displays a list of connected USB mass storage devices This item appears only when a USB storage device is installed OffBoard SATA Controller Configuration Displays information on your M 2 PCle SSD if installed Trusted Computing 2 0 This sub menu appears only when Intel Platform Trust Technology is set to Enabled E v v Security Device Support Enables or disables Trusted Platform Module TPM Default Enable Pending operation To clear TPM related settings set this item to TPM Clear Default None TPM 20 InterfaceType Allows you to select the communication interface for the TPM 2 0 device
37. he use of a fan with fan speed control design For optimum heat dissipation it is recommended that a system fan be installed inside the chassis CPU_FAN SYS_FAN1 2 Pin No Definition Pin No Definition 1 GND 1 GND 2 12V SELA 2 12V Speed Control CPU FAN 3 Sense 1 3 Sense 4 Speed Control SYS_FAN3 4 VCC SYS_FAN2 SYS_FAN3 Pin No Definition 1 GND 2 12V 3 N A e Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating Overheating may result in damage to the CPU or the system may hang e These fan headers are not configuration jumper blocks Do not place a jumper cap on the headers SATA3 0 1 2 3 4 5 SATA 6Gb s Connectors The SATAconnectors conform to SATA6Gb s standard and are compatible with SATA3Gb s and SATA 1 5Gb s standard Each SATA connector supports a single SATA device Pin No Definition SATA3 1 GND 5 3 1 2 TXP eer 3 TXN 4 GND CS SS oe SS 5 TRP 7 GND To enable hot plugging for the SATA ports refer to Chapter 2 BIOS Setup Peripherals SATA Configuration for more information 6 M 2 M 2 Socket 3 Connector The M 2 connectors support M 2 SATA SSDs and M 2 PCle SSDs O O QO 80G 60G 42G Follow the steps below to correctly install an M 2 SSD in the M 2 connector Step 1 Use a screw driver to unfasten the screw an
38. hold waste disposal service or where you purchased the product for details of environmentally safe recycling When your electrical or electronic equipment is no longer useful to you take it back to your local or regional waste collection administration for recycling f you need further assistance in recycling reusing in your end of life product you may contact us at the Customer Care number listed in your product s user s manual and we will be glad to help you with your effort Finally we suggest that you practice other environmentally friendly actions by understanding and using the energy saving features of this product where applicable recycling the inner and outer packaging including shipping containers this product was delivered in and by disposing of or recycling used batteries properly With your help we can reduce the amount of natural resources needed to produce electrical and electronic equipment minimize the use of landfills for the disposal of end of life products and generally improve our quality of life by ensuring that potentially hazardous substances are not released into the environment and are disposed of properly 36 FCC Notice U S A Only This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipme
39. ining methods gt gt Auto Lets the BIOS automatically configure this setting Default gt Enable Fast Boot Skip memory detection and training in some specific criteria for faster memory boot Disable Fast Boot Detect and train memory at every single boot Note 1 This item is present only when you install a CPU that supports this feature For more information about Intel CPUs unique features please visit Intel s website Note 2 This item is present only when you install a CPU and a memory module that support this feature 93 gt Memory Enhancement Settings Provides several memory performance enhancement settings Normal basic performance Relax OC Enhanced Stability and Enhanced Performance Default Normal Memory Timing Mode Manual and Advanced Manual allows the Memory Multiplier Tweaker Channel Interleaving Rank interleaving and memory timing settings below to be configurable Options are Auto default Manual Advanced Manual Profile DDR Voltage Displays the memory voltage Memory Multiplier Tweaker Provides different levels of memory auto tuning Default Auto Channel Interleaving Enables or disables memory channel interleaving Enabled allows the system to simultaneously access different channels of the memory to increase memory performance and stability Auto lets the BIOS automatically configure this setting Default Auto Rank Interleaving Enables or disables memory rank interle
40. ively lower the CPU voltage and core frequency to decrease average power consumption and heat production Auto lets the BIOS automatically configure this setting Default Auto Voltage Optimization Allows you to determine whether to enable voltage optimization to reduce power consumption Default Enabled RSR Allows you to determine whether to automatically lower the CPU turbo ratio if the CPU voltage temperature is too high Default Enabled Hardware Prefetcher Allows you to determine whether to enable hardware prefetcher to prefetch data and instructions from the memory into the cache Default Enabled Adjacent Cache Line Prefetch Allows you to determine whether to enable the adjacent cache line prefetch mechanism that lets the processor retrieve the requested cache line as well as the subsequent cache line Default Enabled System Memory Multiplier Allows you to set the system memory multiplier Auto sets memory multiplier according to memory SPD data Default Auto Memory Frequency MHz The first memory frequency value is the normal operating frequency of the memory being used the second is the memory frequency that is automatically adjusted according to the System Memory Multiplier settings Advanced Memory Settings System Memory Multiplier Memory Frequency MHz The settings above are synchronous to those under the same items on the Advanced Frequency Settings menu Memory Boot Mode 2 Provides memory detection and tra
41. m Power ea S Information eS Peripherals Management Save amp Exit English Q F lash Boot Option Priorities Boot Option 1 UEFI USB 2 0 Flash Disk 4 00 Partition 1 en FAT16 32 Format Only Boot Option Priorities Specifies the overall boot order from the available devices Removable storage devices that support GPT format will be prefixed with UEFI string on the boot device list To boot from an operating system that supports GPT partitioning select the device prefixed with UEFI string Or if you want to install an operating system that supports GPT partitioning such as Windows 7 64 bit select the optical drive that contains the Windows 7 64 bit installation disk and is prefixed with UEFI string Hard Drive CD DVD ROM Drive Floppy Drive Network Device BBS Priorities Specifies the boot order for a specific device type such as hard drives optical drives floppy disk drives and devices that support Boot from LAN function etc Press lt Enter gt on this item to enter the submenu that presents the devices of the same type that are connected This item is present only if at least one device for this type is installed Bootup NumLock State Enables or disables Numlock feature on the numeric keypad of the keyboard after the POST Default On Security Option Specifies whether a password is required every time the system boots or only when you enter BIOS Setup After configuring this item set the password s under the A
42. nt generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult a dealer or experienced TV radio technician for help Canada Industry Canada IC Notices Canada avis d Industry Canada IC This Class B digital apparatus complies with Canadian ICES 003 and RSS 210 Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Cet appareil num rique de classe B est conforme aux normes canadiennes ICES 003 et RSS 210 Son fonctionnement est soumis aux deux conditions suivantes 1 cet appareil ne doit pas causer d interf rence et 2 cet appareil doit accepter toute interference notamment les interferences qui peu
43. on of BIOS from the Internet and updates the BIOS BIOS itis recommended that you not flash the BIOS To flash the BIOS do it with caution Inadequate BIOS flashing may result in system malfunction e It is recommended that you not alter the default settings unless you need to to prevent system instability or other unexpected results Inadequately altering the settings may result in system s failure to boot If this occurs try to clear the CMOS values and reset the board to default values Refer to the Load Optimized Defaults section in this chapter or introductions of the battery clear CMOS jumper in Chapter 1 for how to clear the CMOS values T e Because BIOS flashing is potentially risky if you do not encounter problems using the current version of 2 1 Startup Screen The following startup Logo screen will appear when the computer boots Sample BIOS Version F1a GIGABYTE insiston Ultra Durable Function Keys On the main menu of the BIOS Setup program press arrow keys to move among the items and press lt Enter gt to accept or enter a sub menu Or you can use your mouse to select the item you want e When the system is not stable as usual select the Load Optimized Defaults item to set your system to its defaults e The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version 20 2 2 GIGABYTE UEFI DuaIBIOS System BIOS Power Information Features Peripherals Chips
44. on to this port DVI D Port ot The DVI D port conforms to the DVI D specification and supports a maximum resolution of 1920x1200 60 Hz the actual resolutions supported depend on the monitor being used Connect a monitor that supports DVI D connection to this port USB Type C Port The reversible USB port supports the USB 3 1 specification and is compatible to the USB 3 0 2 0 specification Use this port for USB devices Note The DVI D port does not support D Sub connection by adapter 10 USB 3 0 2 0 Port The USB 3 0 port supports the USB 3 0 specification and is compatible to the USB 2 0 1 1 specification Use this port for USB devices USB 3 1 Type A port Red The USB 3 1 Type A port supports the USB 3 1 specification and is compatible to the USB 3 0 2 0 1 1 specification Use this port for USB devices HDMI Port The HDMI port is HDCP compliant and supports Dolby True HD and DTS HD HIGH DEFINITION MuLTiMeoia nrenrace Master Audio formats It also supports up to 192KHz 24bit 8 channel LPCM audio output You can use this port to connect your HDMl supported monitor The maximum supported resolution is 4096x2160 24 Hz but the actual resolutions supported are dependent on the monitor being used RJ 45 LAN Port The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate The following describes the states of the LAN port LEDs Sortie Activity
45. placing the battery A e Replace the battery with an equivalent one Danger of explosion if the battery is replaced with an incorrect model e Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncertain about the battery model e When installing the battery note the orientation of the positive side and the negative side of the battery the positive side should face up e Used batteries must be handled in accordance with local environmental regulations Chapter 2 BIOS Setup BIOS Basic Input and Output System records hardware parameters of the system in the CMOS on the motherboard Its major functions include conducting the Power On Self Test POST during system startup saving system parameters and loading operating system etc BIOS includes a BIOS Setup program that allows the user to modify basic system configuration settings or to activate certain system features When the power is turned off the battery on the motherboard supplies the necessary power to the CMOS to keep the configuration values in the CMOS To access the BIOS Setup program press the lt Delete gt key during the POST when the power is turned on To upgrade the BIOS use either the GIGABYTE Q Flash or BIOS utility e Q Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system e BIOS is a Windows based utility that searches and downloads the latest versi
46. r C6 C7 mode in system halt state When enabled the CPU core frequency and voltage will be reduced during system halt state to decrease power consumption The C6 C7 state is a more enhanced power saving state than C3 Auto lets the BIOS automatically configure this setting Default Auto Note This item is present only when you install a CPU that supports this feature For more information about Intel CPUs unique features please visit Intel s website 22 v C8 State Support te 1 Allows you to determine whether to let the CPU enter C8 mode in system halt state When enabled the CPU core frequency and voltage will be reduced during system halt state to decrease power consumption The C8 state is a more enhanced power saving state than C6 C7 Auto lets the BIOS automatically configure this setting Default Auto Package C State Limit Allows you to specify the C state limit for the processor Auto lets the BIOS automatically configure this setting Default Auto CPU Thermal Monitor 8 1 Enables or disables Intel Thermal Monitor function a CPU overheating protection function When enabled the CPU core frequency and voltage will be reduced when the CPU is overheated Auto lets the BIOS automatically configure this setting Default Auto CPU EIST Function e Enables or disables Enhanced Intel Speed Step Technology EIST Depending on CPU loading Intel EIST technology can dynamically and effect
47. r way to browse the web Google Toolbar for Internet Explorer 1 Please visit GIGABYTE s website for more software information Please visit GIGABYTE s website for details on configuring the audio software lt 37 Regulatory Statements Regulatory Notices This document must not be copied without our written permission and the contents there of must not be imparted to a third party nor be used for any unauthorized purpose Contravention will be prosecuted We believe that the information contained herein was accurate in all respects at the time of printing GIGABYTE cannot however assume any responsibility for errors or omissions in this text Also note that the information in this document is subject to change without notice and should not be construed as a commitment by GIGABYTE Our Commitment to Preserving the Environment In addition to high efficiency performance all GIGABYTE motherboards fulfill European Union regulations for RoHS Restriction of Certain Hazardous Substances in Electrical and Electronic Equipment and WEEE Waste Electrical and Electronic Equipment environmental directives as well as most major worldwide safety requirements To prevent releases of harmful substances into the environment and to maximize the use of our natural resources GIGABYTE provides the following information on how you can responsibly recycle or reuse most of the materials in your end of life product Restriction of Hazardou
48. s 1 0 Check your motherboard revision before updating motherboard BIOS drivers or when looking for technical information Example Table of Contents GA B150 HD3P Motherboard Layout cccccccsecsscsssscsscsssscsessssecsssessseesessseesessseeen 4 Chapter 1 Hardware Installation ccccccssccssscsecsssecsscsssecsscessecseeessesssessesasesaseesseas 5 t1 instalation PIE CAUTIOIG siuiccvaxsscerussusudsrssncnasvesulaananitesseauvvianoisdinteastuactilaaanadauaes 5 12 Product Specifications sssi bescecinatdeecebacateaedest eee 6 to Mstlng the CPU seesi a T 9 14 stalling he MEMON sssrin a 9 1 5 sialing an Epansion Card sessen 10 1 6 Back Panel Connectors cccccsesesssesssssssscsssssessssssessessesssssesssersesasessesaeen 10 1 7 Internal CONIC CONS scscscaicnc ties eideaceseccoeneseonasptsectncasiccaexsinartnead ncsnatacsdaidcaremdncuaues 12 Chapter 2 BIOS Setup i scisecicnstcacucaiecenssnstcnnascaesestone ienususnseacesisesacatasesatenieneataiwsessuntteened 20 2 Santup SCEE ie ea ae eee eer ee eee rete 20 r RM a ae cag sees ate sett gence E 21 23 Systeri NOMANON sessirnir EE eae a cet E AE eeatens 21 24 BIOS CAC cer sec esa cateenn dinn aAA ai 28 EO HOV Cals enra R AET R 31 L C Eea A E E ace eiee eaneees eee 33 ZF POWER Management osiinsa asien 34 Oe AN EN Ea E E E AE 36 enano ATO E E 37 Drivers IVS GeO Mats csredeccersci sstonexeasheentechetseceena sbaciteciuenlecalseenseheeeneaseteeachauneselanteheeeetaeee 37 Regulator
49. s Substances RoHS Directive Statement GIGABYTE products have not intended to add and safe from hazardous substances Cd Pb Hg Cr 6 PBDE and PBB The parts and components have been carefully selected to meet ROHS requirement Moreover we at GIGABYTE are continuing our efforts to develop products that do not use internationally banned toxic chemicals Waste Electrical amp Electronic Equipment WEEE Directive Statement GIGABYTE will fulfill the national laws as interpreted from the 2002 96 EC WEEE Waste Electrical and Electronic Equipment directive The WEEE Directive specifies the treatment collection recycling and disposal of electric and electronic devices and their components Under the Directive used equipment must be marked collected separately and disposed of properly WEEE Symbol Statement The symbol shown below is on the product or on its packaging which indicates that this product Ds must not be disposed of with other waste Instead the device should be taken to the waste collection centers for activation of the treatment collection recycling and disposal procedure The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local government office your house
50. t gt Manual Allows you to control the fan speed under the Fan Speed Percentage item gt gt Full Speed Allows the fan to run at full speeds Fan Speed Percentage Allows you to control the fan speed This item is configurable only when 1st System Fan Speed Control is set to Manual Options are 0 75 PWM value C 2 50 PWM value C 2nd System Fan Speed Control SYS_FAN2 Connector Allows you to determine whether to enable the fan speed control function and adjust the fan speed gt gt Normal Allows the fan to run at different speeds according to the system temperature You can adjust the fan speed with System Information Viewer based on your system requirements Default gt gt Silent Allows the fan to run at slow speeds gt gt Manual Allows you to control the fan speed under the Fan Speed Percentage item gt gt Full Speed Allows the fan to run at full speeds Fan Speed Percentage Allows you to control the fan speed This item is configurable only when 2nd System Fan Speed Control is set to Manual Options are 0 75 PWM value C 2 50 PWM value C Miscellaneous Settings Max Link Speed Allows you to set the operation mode of the PCI Express slots to Gen 1 Gen 2 or Gen 3 Actual operation mode is subject to the hardware specification of each slot Auto lets the BIOS automatically configure this setting Default Auto 3DMark01 Enhancement Allows you to determine whether to enhance some legacy benchmark perform
51. t and connects a S PDIF digital audio cable provided by expansion cards for digital audio output from your motherboard to certain expansion cards like graphics cards and sound cards For example some graphics cards may require you to use a S PDIF digital audio cable for digital audio output from your motherboard to your graphics card if you wish to connect an HDMI display to the graphics card and have digital audio output from the HDMI display at the same time For information about connecting the S PDIF digital audio cable carefully read the manual for your expansion card CD 1 Pin No Definition 1 SPDIFO 2 GND 11 F_USB30_1 USB 3 0 2 0 Header The header conforms to USB 3 0 2 0 specification and each header can provide two USB ports For purchasing the optional 3 5 front panel that provides two USB 3 0 2 0 ports please contact the local dealer Pin No Definition Pin No Definition 1 VBUS 11 D2 i i 2 SSRX1 12 D2 3 SSRX1 13 GND 4 GND 14 SSTX2 5 SSTX1 15 SSTX2 6 SSTX1 16 GND 11 10 7 GND 17 SSRX2 8 D1 18 SSRX2 9 D1 19 VBUS 10 NC 20 No Pin 12 F_USB1 F_USB2 USB 2 0 1 1 Headers The headers conform to USB 2 0 1 1 specification Each USB header can provide two USB ports via an optional USB bracket For purchasing the optional USB bracket please contact the local dealer Pin No Definition Pin No Definition 9 1 Power 5V 6 USB DY
52. ult This item is configurable only when Fast Boot is set to Enabled This function is disabled when Fast Boot is set to Ultra Fast PS2 Devices Support gt gt Disabled All PS 2 devices are disabled before the OS boot process completes gt Enabled All PS 2 devices are functional in the operating system and during the POST Default This item is configurable only when Fast Boot is set to Enabled This function is disabled when Fast Boot is set to Ultra Fast NetWork Stack Driver Support gt Disabled Disables booting from the network Default gt Enabled Enables booting from the network This item is configurable only when Fast Boot is set to Enabled or Ultra Fast Next Boot After AC Power Loss gt gt Normal Boot Enables normal bootup upon the return of the AC power Default gt Fast Boot Keeps the Fast Boot settings upon the return of the AC power This item is configurable only when Fast Boot is set to Enabled or Ultra Fast Windows 8 10 Features Allows you to select the operating system to be installed Default Other OS CSM Support Enables or disables UEFI CSM Compatibility Support Module to support a legacy PC boot process gt Enabled Enables UEFI CSM Default gt gt Disabled Disables UEFI CSM and supports UEFI BIOS boot process only This item is configurable only when Windows 8 10 Features is set to Windows 8 10 or Windows 8 10 WHQL LAN PXE Boot Option ROM Allows you to select whether to
53. vent affecter son fonctionnement 39 Contact Us GIGA BYTE TECHNOLOGY CO LTD Address No 6 Baogiang Rd Xindian Dist New Taipei City 231 Taiwan TEL 886 2 8912 4000 FAX 886 2 8912 4005 Tech and Non Tech Support Sales Marketing http esupport gigabyte com WEB address English http www gigabyte com WEB address Chinese http www gigabyte tw You may go to the GIGABYTE website select your language in the language list on the top right corner of the website e GIGABYTE eSupport To submit a technical or non technical Sales Marketing question please link to http esupport gigabyte com GIGABYTE Support 5 a if Downloads FAQ Warranty A Sign in with s f ao i es Password Forget password Login a Not a member yet All intellectual property rights including without limitation to copyright and trademark of this work and its derivative works are the property of or are licensed to GIGA BYTE TECHNOLOGY CO LTD Any unauthorized use is strictly prohibited 40
54. y Statement ccccssssssssscssssssssssssesscessessssssssssseseesecesersesseersevasessesaeen 38 AG ES es 2s E eae reaps se desee cccse ea seseseheciceees dened toteesonecsneseacgeiosa seaeeaioce 40 GA B150 HD3P Motherboard Layout TH ATX_12V_2X4 fojo EEE SYS_ EE LGA1151 Intel USB 3 1 Controller in GA ba HD3P 80G 60G 42G Oo O O 2l E PCIEX1_1 CPU_FA Intel B150 iTE PCIEX4 110 Super SATA3 Ee ee SYS_FAN3 F_USB30_1 PCIEX16 00 SATA EXPRESS I O O OB BIOs CODEC OE armen Jt CIMBIOS PCI Bridge Ta mn EE mar ee EE F_AUDIO COMA LPT TPM F_USB2 F_USB1 F_PANEL SYS_FAN2 Box Contents vI GA B150 HD3P motherboard MI Motherboard driver disk MI Two SATA cables VI User s Manual MI I O Shield The box contents above are for reference only and the actual items shall depend on the product package you obtain The box contents are subject to change without notice iA Chapter 1 Hardware Installation 1 1 The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge ESD Prior to installation carefully read the user s Installation Precautions manual and follow these procedures Prior to installation make sure the chassis is suitable for the motherboard Prior to installation do not remove or break motherboard S N Serial Number sticker or warranty sticker provided by your dealer These stick
Download Pdf Manuals
Related Search