For your own safety, please read this user manual - Techni-Lux
Contents
1. Safety eyelet Dip switches Intensity Y ON DMN PWN Speed or MIC sensitivity 10 Analog signals input 11 Analog signals output 12 Status indicator 13 DMX in 14 DMX out SAFETY INSTRUCTIONS CAUTION Be careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual gt gt Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature 2 STROBE 5000 v1 0 This device falls under protection class I Therefore it is essential that the device be earthed The electric connection must carry out by qualified person The device shall only be used with rate dvoltage and frequency Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement o2. LIGHTING PROFESSIONAL FLASHER USER MANUAL STROBE Sooo KEEP THIS MANUAL FOR FUTURE NEEDS Thank you for your patronage We are confident that our excellent products and service can satisfy you For your own safety please read this user manual carefully before installing the device CAUTION eep this device away from rain and moisture CAUTION Unplug mains lead before opening the housing In order to install operate and maintain the lighting safety and correctly We suggest that the installation and operation should be done by the verified technician and follow the instruction strictly INTRODUCTION Thank you for having chosen this professional strobe lighting You will see you have acquired a powerful and versatile device Unpack the device Inside the box you should find 1 The fixture device 2 One power cable 3 One XLR connection cable 4 One safety rope and this manual Please check carefully that there is no damage caused by transportation Should there be any consult your dealer and don t install this device Features Lamp JENBO PS 1500 Control signal Standard DMX 512 2 channels e Stand alone operation with master slave function can be sound activated e Dimmer intensity from 0 to 100 e Strobe 1 25 flashes per second e Auto program 4 pre build programs can be selected 1 STROBE 5000 v1 0 Overview Lamp Mounting bracket Housing Fixation screw Power
3. 1 JACK STRO BE 3 MONGO JAG p E TS 1 CLEANING AND MAINTENANCE The following points have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed CAUTION Disconnect from mains before starting maintenance operation We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device except for the lamp Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine parts from your local dealer TECHNICAL SPECIFICATIONS Power supply 98V AC 50Hz Ll 120 50 7 1208 50Hz LI220VAC 50Hz LI230VAC 50Hz LI240VAC 50Hz 98V AC 60Hz Ll 120V AC 60Hz LI208VAC 50Hz LJ220VAC 60Hz 1230VAC 60Hz _1240VAC 60Hz Power consumption max 1500W Lamp JE
4. Please remember the lamp is not a hot restrike type you must wait for approximately 15 minutes after having turned off the lamp before you can turn it back on again CAUTION Do not operate this device with open cover 4 STROBE 5000 v1 0 b Mounting the device CAUTION A Please consider the GB7000 1 2007 GB7000 217 2008 and the other respective national norms during the installation The installation must only be carried out by a qualified person The applicable temperature for the lighting is between 10 C to 45 C Do not use the lighting under or above the temperature The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment e g an appropriate safety cable Never stand directly below the device when mounting removing or servicing the fixture The operator has to make sure the safety relating and machine technical installations are approved by an expert before taking the device into operation for the first time These installations have to be approved by a skilled person once a year CAUTION Before taking into operation for the first time the installation has to be approved by an expert Cautions The effect should be installed outside areas where persons may reach it walk by or be seated CAUTION When installing the device make sur
5. controller The DMX starting address of the controller is defined by the first 9 DIP switches The encoding is binary DIP switch 1 value 1 2 1 DIP switch 2 value 2 21 2 DIP switch 3 value 4 22 4 DIP switch 4 value8 23 8 etc Example if 95 were the desired start address then the settings for the first 9 switches would be as follows 111111101 1 2 4 8 16 0 64 95 You can set the address 95 pushing the pin 1 2 3 4 5 7 to the position ON DMX 512 connection with DMX terminator For installations where the DMX cable has to run a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise For normal products which do not have dip switches setting the DMX terminator is simply an XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain While on the lighting which with the dip Switches setting if the DP12 is put to ON position downwards the fixture gains the function of connecting with a 120 Q resistor then this unit functions as the terminator of the DMX link Controlled via a strobe controller Connect the control cable with 1 4 inch mono jack and please refer to the manual of the strobe controller for operation instruction STR OS lt STRO BE 2 7
6. NBO PS 1500 Packing dimensions 60x26 5x27cm Net weight 6 5KGS Gross weight 7 5KGS Remark errors and omissions for every information given in this manual except All information is subject to change without prior notice 10 STROBE 5000 v1 0
7. Stand Alone by sound activated Status indicator Red green flash Alone by Auto run Mode No matte what value set from DP1 to ON ON 8 this unit work in Alone by Auto run activated Status indicator Red green flash Stand Master by Sound Mode No matte what value set from DP1 to DP8 this unit work in Stand Master by Sound activated Status indicator Red green flash ON FF Master by Auto run Mode No matte what value set from DP1 to O 8 this unit work in Master by Auto run activated Status indicator Red green flash Control via a standard DMX 512 controller When you use a DMX controller to control the strobe please refer to the channel functions as the following DMX channel s functions and their values 2 DMX channels Channel 1 Speed 0 1 Close 2 5 Spring strobe 6 255 Strobe slow to fast Channel 2 Dimmer 0 9 Close 10 255 Intensity 0 100 Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head You can chain multiple Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below 8 STROBE 5000 v1 0 DMX output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket 1 Ground 2 Signal 3 Signal SN 120 Ohms lt DMX512 DMxX
8. e there is no highly inflammable material within a distance of min 0 5m Overhead mounting requires extensive experience including amongst others calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury CAUTION The electric connection must only be carried out by a qualified electrician Before mounting make sure that the installation area can hold a minimum point load of 10 times the device s weight Connect the fixture to the mains with the power plug 5 STROBE 5000 v1 0 Installation method via clamp Please refer to the picture below Screw one clamp each via a M12 screw and nut onto the Omega holders Insert the quick lock fasteners of the first Omega holder into the respective holes on the bottom of the device Tighten the quick lock fasteners fully clockwise Install the second Omega holder Pull the safety rope through the holes on the bottom of the base and over the trussing system or a safe fixation spot Insert the end in the carabine and tighten the safety screw Control via the DIP Switches Please refer to the picture below Doaa ON 41 234567 8 9101112 Please note The dip switch 9 is ON A O Speed or MIC sensitivity Intensity Intensity amp speed or MIC sensit
9. f the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard CAUTION Never touch the device during operation The housing may heat up CAUTION Never look directly into the light source as sensitive persons may suffer an epileptic shock Please be aware that damages caused by manual modifications to the device are not subject to watranty Keep away from children and non professionals GENERAL GUIDELINES This device is a lighting effect for professional use on stages in discotheques theatres etc This fixture is only allowed to be operated with the max alternating current which stated in the technical specifications in the last page of this manual the device was designed for indoor use only Lighting effects are not designed for permanent operation Consistent operation breaks may ensure that the device will serve you for a long time without defects Do not shake the device Avoid brute force when ins
10. ivity adjustment at back of the strobe 6 STROBE 5000 v1 0 FUNCTION LIST VALUE FUNCTION DIP ores pes pes pes oer pes peo peo peni peiz DMX ADDR SETTING Switch Status 1200 terminator connected X X X X Stand Alone by Sound X Alone by Auto run X Stand Master by Sound Master by Auto run 1 1 1 Stand Alone by manual a a ee ele From DP1 to DP12 12 dip switches 5 different functions available according to different dip switch settings In the above list 0 stands for off 1 stands for You can select each function by setting to different dip switches to different values DP 12 is for controlling the connection to the 120Q terminal resistor 7 STROBE 5000 v1 0 From DP 9 to DP 11 are functional switches different settings list below Normal Mode DP1 to DP9 is for setting DMX Address Status indicator Solid Green DMX ready Solid Red No DMX Slave Mode No matter what value set from DP1 to DP8 the unit OFF ON will work as Slave unit in the link Status indicator Solid Green DMX ready Solid Red No DMX Stand Alone by manual Mode No matte what value set from DP1 to DP8 this unit work in Stand Alone by sound activated Status indicator Red green flash Stand Alone by sound Mode No matte what value set from DP 1 to 8 this unit work in
11. talling or operating the device The device shall only be used complete with its protective shield While choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust The minimum distance between light output from the projector and the illuminated surface must be more than 0 5 meter Please use the original packaging if the device is to be transported For safety reasons please be aware that all modifications on the device are forbidden If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to 3 STROBE 5000 v1 0 short circuit burns electric shock lamp explosion crash etc INSTALLATION INSTRUCTIONS a Installing or replacing the lamp CAUTION Only install the lamp with the device unplugged from the mains T CAUTION The lamp has to be replaced when it is damaged or deformed Before replacing the lamp let the lamp cool down because during operation the lamp can reach very high temperature During the installation of halogen lamps do not touch the glass bulbs bare handed Always use a cloth to handle the lamps during insertion and removal Do not install lamps with a higher wattage They generate higher temperatures than which the device was designed for For the installation you need one JENBO PS 1500 Procedure
Download Pdf Manuals
Related Search