Home

LABELMATE LC-CAT

1. back of the unit 2 STANDARD AND 10 Identify the inner Label Flange Slide the Flange Plate onto the hollow end of the Rewind Shaft For maximum width the Flange face should be flush with the end of the Shaft Tighten the screw in the Hub until it is snug Not too tight 3 CHUCK Mount the inner Flange onto the Quick Chuck with two screws provided Slide the Shaft and Flange Assembly onto the LC CAT 2 Motor Shaft allowing for clearance to the CAT 2 Chassis and Motor Screws Tighten the Allen Screw onto the flat part of the Motor Shaft until it is tight 5 ACH Slide the Hub of the ACH over the motor Shaft of the LC CAT 2 Position the Hub so there is a gap between the ACH Hub and the Rewinder Drive Unit case Tighten the Allen Screw onto the flat part of the Motor Shaft until it is tight 6 Plug the Power Supply Output Cable to the Power Jack on the Rear Panel of the LC CAT Plug the Power Supply into a suitable AC Power Mains Outlet 7 CAUTION AVOID ACCIDENTS THE LC CAT WEIGHS OVER12KG SO CHOOSE ONLY A STURDY SURFACE ON WHICH TO SET THE UNIT A FOR YOUR SAFETY Switch off device before any manipulation WHEN USED AS UNWINDER 1 Select the desired direction with the DIRECTION switch 2 Itis recommended to form the loop and put the paper in the printer before switching on the LC CAT 3 To Optimise the performance several parameters can be used a The HIGH LOW Torque Switch b The TORQUE ADJUST knob c The rela
2. H 300mm diameter for LC CAT 2 and 400mm for LC CAT 40 Speed 1250mm sec for LC CAT 2 and LC CAT 40 320mm sec for LC CAT 40G Max speeds specified with a 76mm take up roll diameter Start Stop ON OFF ON Direction Switch Power Supply Input 230VAC 50 60Hz e KEEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE e A WARNING This Product is for indoor use only Not for use in wet locations IMPORTANT INFORMATION e This product is a label unwinder It is only to be used to rewind or unwind labels of the recommended dimensions and weight in an indoor dry environment e The machine has to be unplugged before any manipulation The machine is to be used on a flat surface if the surface is not flat it is to be fixed using the holes in the base plate e Do not leave the power cable in a passageway e The ambient light of the working area needs to be sufficient to avoid any risk e The unwinder can be used in ambient temperatures of 2 C to 40 C e Connection of the machine to the power source must respect local and European legislations SET UP LC CAT TO PRINTER To Rear panel showing UPPER gt photo detectors connectors PHOTO DETECTORS LOWER gt 1 The two photo detectors are identical The UPPER photo detector see drawing above should be connected to the connector labelled UPPER at the back of the unit The LOWER photo detector should be connected to the connector labelled LOWER at the
3. MAINTENANCE Your LC CAT requires no maintenance Product Limited Warranty All Labelmate Products are warranted to the original end user customer to be free from defects in materials and workmanship If it is determined by Labelmate that a product has failed under the terms of this warranty the product will be repaired or replaced at no charge to the customer Labelmate reserves all rights to determination of coverage and liability under this warranty The warranty period for all new Labelmate products is outlined below Warranty Period Products Covered Label Rewinders meas Label Unwinders Label Counters mechanical parts only Label Slitters mechanical parts only Label Dispensers Printer Mechanisms Power Supply Modules Counter modules Encoders Any products not specified above The warranty period for all products starts on the date purchased by the original end user customer Warranty coverage is not transferable with ownership and will terminate immediately upon rental resale or any other change in ownership This warranty does not cover repair to any product which is damaged has been modified is missing parts or has been opened or repaired by any unauthorised person Use of any unauthorised accessory or attachment will void coverage Purchase documentation should be retained for coverage verification In the event your product requires service please contact the distributor you bought the product from The cust
4. omer assumes responsibility for all cost and risk incurred in transport for service Labelmate makes no other warranty of any kind expressed or implied or to suitability or fitness for a particular purpose No other person agent or reseller is authorised to give any warranties on behalf of Labelmate Any obligation to warranty other than that specifically addressed above is hereby disclaimed LABELMATE LLC 69 AVENUE ALPHONSE XIII 1180 BRUSSELS BELGIUM TEL 322 375 69 60 FAX 322 375 38 96 brussels labelmate com www labelmateeurope com LABELMATE User_LC CAT CE 01 13 Original user manual LABELMATE LC CAT Paper Loop Controlled Label Unwinder Rewinder Remove all parts from the shipping container and verify contents PACKAGE CONTENTS User Manual this document LC CAT Drive Unit Power cord LABELMATE Quick Chuck Quick Locking Core Chuck or Standard Shaft with three 3 metal Vanes installed or Model 10 INCHES Shaft with six 6 metal Vanes installed or Model ACH Adjustable Core Holder e Two 300mm Plastic Flange Plates only one for QC and none for ACH e Two visible light reflective photo detectors with 2 meter long cables and mating connectors SPECIFICATIONS Weight of the machine 12 2Kg to 14 5Kg depending on model Max Label Roll Weight 8Kg for LC CAT 3 Standard and LC CAT 3 QC 14Kg for LD CAT 40G 7Kg for LC CAT 3 ACH Max Label Roll Size 280mm for LC CAT 3 AC
5. tive positions of the UPPER and LOWER photo detectors with respect to the loop d The distance between the UPPER and LOWER photo detectors e The range of the reflective photo detectors is adjustable to maximum 40 cm As delivered the range is set to about 15 cm The range can be changed by adjusting the potentiometer located on the photo detectors EXTERNAL HALT CONTROL An External Halt Control jack on the CAT 2 is for use with external devices capable of providing an open circuit halt command A 3 5mm control cable is necessary for use not included With Pin 2 and Pin 3 of the External Halt Control circuit closed connected together using a 3 5mm dual circuit plug the CAT 2 will operate When the External Circuit is opened the CAT 2 will stop 3 5mm EXTERNAL HALT CONTROL Plug Dual Circuit Plug Contact CLOSED RUN Contact OPEN HALT Pin 1 No connection NOT USED Pin 2 Normally Closed NC contact Pin 3 Normally Closed NC contact return 12V Pipe EXT HALT CONT 1 OK E 3 5 mm Jack w 1 K G Dual Circuit 10K gt S VV

LABELMATE LC-CAT

Contents

Download Pdf Manuals

Related Search

Related Contents