to Open Manual File - American Musical Supply
Contents
1. An appliance and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn This product is in compliance with EU WEEE regulations Disposal of end of life product should not be treated as municipal waste Please refer to your local regulations for instructions on proper disposal of this product 1 An apparatus with Class construction shall be connected to a mains sockets outlet with protective earthing connection 2 Where the mains plug or an appliance coupler is used as the disconnect device the disconnection device shall remain readily operable Read these instructions Keep these instructions Head all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the po2. The clip indicator can be a preferred setting while tracking or mixing at louder volumes to indicate the potential for excessive volumes that can damage your monitors 2 In the Off position the clip LED is inactive and the limiter is bypassed 3 In the Limit position the signal is routed through the Limiter circuit and the signal is limited when a predetermined threshold is passed When the limiter is activated by overdriving the amplifier the led will illuminate The duration and intensity of the green LED will increase as limiting increases It is not recommended to mix with the limiter activated as the limiting of the audio signal will change the characteristics of the audio If you are finding that you need to activate the limiter for mixing then it is recommended to instead turn your system down to limit overdriving the audio signal Connecting Your System POWERING ON All connections should be made all faders and controls should be set at their minimum levels and all other equipment should be powered on prior to powering on your V8 monitors The power On Off switch is located on the rear pane The KRK Logo on the front baffle illuminates when the power is applied Audio Mute Switch Placing this switch in the ON position activates a timing circuit whereby the High Voltage Power Supply is shut off after approximately 20 minutes if no audio signal is detected The Low Voltage Power supply is still drawing current The monitor wi
3. INTO THE EARTH IF REQUIRED BY POWER SERVICE GROUNDING ELECTRODE SYSTEM eS Interior metal water pipe LOCAL CODES SEE NEC SECTION 810 2i 7 NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV system installer s attention to Article 820 40 of the National Electrical Code that provides guidelines for proper grounding and in particular specifies that the ground cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical DO NOT ATTEMPT SERVICING OF THIS UNIT YOURSELF REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Upon completion of any servicing or repairs request the service shop s assurance that only Factory Authorized Replacement Parts with the same characteristics as the original parts have been used and that the routine safety checks have been performed to guarantee that the equipment is in safe operating condition REPLACEMENT WITH UNAUTHORIZED PARTS MAY RESULT IN FIRE ELECTRIC SHOCK OR OTHER HAZARDS Www americanmusical com Introduction Congratulations on your KRK purchase And welcome to the growing family of KRK owners KRK s VXT Series of powered studio monitors are precision speakers designed to forever change the way you handle your most demanding audio jobs VXT means truth in French and that s just what these monitors are all about they reveal the truth in your audio material The VXT monitors feature key design el
4. U E R G U l D E www americanmusical com KRK VXT SERIES BI AMPLIFIED STUDIO MONITOR x gt www americanmusical com IMPORTANT SAFETY INSTRUCTIONS CAUTION ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR Fr SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Warning To reduce the risk of fire or electric shock do not expose this unit to rain or moisture The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product Do not place this unit on an unstable cart stand or tripod bracket or table The unit may fall causing serious injury to a child or adult and serious damage to the unit Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the unit Any mounting of the device on a wall or ceiling should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer
5. and this can occur in the speakers themselves The VXT series has very low speaker distortion which of course translates into improved reproduction accuracy Various amplifier distortions have been eliminated as well the most common being intermodulation transient intermodulation and harmonic distortion Distortion can also occur when the waveform is impacted by physical conditions such as port turbulence and diffraction KRK engineers have implemented design concepts that eliminate or minimize these damaging conditions 3 Resonance Management Resonance is the tendency of something to vibrate at a particular frequency after the source of energy is removed Resonances also play a major role in impacting the performance of a speaker KRK design elements minimize driver and enclosure resonance www americanmusical com Design Elements New Custom Made Tweeter and Woofer Designs KRK is renowned for designing high performance studio monitor drivers Your VXT monitors are no exception A woven Kevlar low frequency driver was custom designed specifically for each model Kevlar amp is one of the strongest lightest most rigid materials that can be used in modern speaker cone construction Kevlar s unique physical properties minimize axial or conical break up modes Both tweeters and woofer provide faster attack times The new tweeters provide enhanced high frequency extension with improved distortion characteristics Resonant Free Exte
6. ation If your subwoofer has a phase switch adjust the subwoofer to provide the highest frequency setting possible Flip the switch back and forth to find the loudest setting Then adjust the sub s low pass filter so that it works in conjunction with the satellite s high pass frequencies the readjust the level of the sub www americanmusical com Figure 3 a A 5 1 Channel Surround Sound Setup Begin by placing the Left and Right front channels 30 degrees from the Center channel and equidistant to the listening position Figure 4 The Left Surround rear and Right Surround rear channels should be placed 110 degrees from the Center channel Their location should also be equidistant from the listening position The subwoofer Low Frequency Effects channel is most effective when situated directly below the Center channel as shown in Figure 4 If this is not possible place the subwoofer just to the right or left side and below the Center channel Ensure that the woofers are above the height of the console Figure 4 10 7 1 Channel Surround Sound Setup The 7 1 channel surround sound setup adds two speakers to the sides of the mix position and is most similar to the actual surround sound configuration of cinema with the difference being that cinemas commonly add additional side surrounds to compensate for the length of the theater The front Left and Right speakers typically form a wider triangulation in r
7. cing Www americanmusical com 12 Problem The sound quality changes Repeat steps in the previous troubleshooting section above before continuing to the next steps Disconnect the signal cable at the input of the monitor With power on place your ear close to each driver tweeter woofer and listen for noise i e a slight hiss or hum If there s absolutely no sound whatsoever it could be that one or more of the drivers woofer or tweeter or both is at fault It s also possible that the problem lies some where in the electronics Play some non distorted source material at a low volume Carefully cover the tweeter to block the sound without touching the diaphragm Is the woofer producing a clean sound If there is not a clear tonal quality or any sound at all then the woofer probably needs to be replaced Cover the woofer so you can hear mostly the tweeter Is the tweeter producing a clear sound f there is not a clear tonal quality or any sound at all then the tweeter probably needs to be replaced Once you have a better idea of what may be at fault then call us and speak with someone in the service department They will help you determine the best solu tion to correct your monitors The service department can be reached at 954 316 1580 Problem The monitor hisses hums or makes other loud noises Here are some suggestions that will help you eliminate these undesirables from your system Make sure that the power cord
8. djust Whole Space 3dB 52Hz Half Space 3dB 60 Hz Quarter Space 3dB 75Hz IHF 30 Watts LF 60 Watts 3 15A 100VAC 50Hz 3 15A 110 120VAC 50 60Hz 1 6A 220 240VAC 50 60Hz Freq Response 56Hz 22kHz 2dB 49Hz 22kHz 1 5dB Music 108dB Peak 111dB 14 1 2 H x 10 1 3 W x 9 5 8 D 5 6cm H x 18 6cm W x 17 7cm 36 8cm H x 26 3cm W x 24 6cm D 27 Ibs LR 1 4 TRS Combo 10k Ohm Blanced Pin 1 Sleeve Ground Pin 2 Tip High Pin 3 Ring Low System Level Adjust 6dB to 30dB Variable Ground Lift LFT On or GND Off Clip Indicator On Off or Limit Auto Mute On or Off HF Adjust 1dB Flat 1dB LF Adjust Whole Space 3dB 40Hz Half Space 3dB 48 Hz Quarter Space 3dB 62Hz IHF 60 Watts LF 120 Watts 4 0A 100VAC 50Hz 4 0A 110 120VAC 50 60Hz 0A 220 240VAC 50 60Hz 37Hz 22kHz 1 5dB Music 111dB Peak 114dB 17 1 4 Hx 12 1 2 W x 11 7 8 D 43 8cm H x 31 8cm W x 30 0cmD 41 Ibs 60 0 WBX 17 75mm Min 26 0mm Max 15 Www americanmusical com WWW KRKSYS CO M LITK00023
9. elation to the mix position than that of a 5 1 setup so as to more accurately replicate the fact that in cinema the front speakers are not angled toward the center but rather face straight out into the theater as is also the case for the mix stage in film sound mixing The Center channel loudspeaker is positioned directly in the center as is the case in a 5 1 surround setup Similarly the subwoofer is most effective when situated directly below the center channel If this is not possible place the subwoofer just to the right or left side and below the Center channel Like the three front speakers the Left and Right surround speakers are positioned at equidistance from the mix position directly to the sides Finally the Left and Right rear surround speakers are placed behind the mix position at equidistance to the mix position The 7 1 channel surround sound environment is one of total immersion and is the best choice for mix environments where sound needs to be detectable side to side along with front to rear Once the monitors have been placed you ll need to adjust the System Gain pots for each monitor so that all channels have exactly the same SPL output at the listening position Although this can be done simply by listening to each channel one at a time and adjusting for relative levels we recommend using an SPL meter and filtered noise pink noise to test each channel independently Simply take a reading from each monitor and then adju
10. ements that continue to make the KRK sound a studio standard The series was created using stringent design philosophies similar to KRK s flagship close field monitor the Expos The VXT Series includes new custom made woofers and tweeters a curved front panel for improved imaging a new cabinet design that provides improved structural integrity and extended low end and slotted ports that greatly reduce port turbulence What s more we ve provided valuable and practical features like an improved speaker protection circuit for added confidence and new drivers for extended frequency response The result is a studio reference monitor that you can trust delivering defined low end articulate midrange and precise natural highs Whether you are making critical mixing decisions or need to capture the subtle nuances of a unique sound you ll quickly discover that the VXT Series is as precise about your work as you are This manual is intended to inform you of the many features of your new VXT monitors and their operation We encourage you to take a few minutes to familiarize yourself with this manual Thank you for choosing KRK IMPORTANT NOTE Your VXT monitor was originally packaged in a specially designed carton Please save these items They should be used when transporting or shipping your monitors Design Philosophy A studio monitor is a tool used to aurally measure the changes in an audio path Ask any seasoned recording pro
11. enna is connected to your tuner or tuner preamplifier be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA No 70 1984 provides information with respect to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode a Use No 10 AWG 5 3mm2 copper No 8 AWG 8 4mm2 aluminium No 17 AWG 1 0mm2 copper clad steel or bronze wire or larger as a ground wire b Secure antenna lead in and ground wires to house with stand off insulators spaced from 4 6 feet 1 22 1 83 m apart Mount antenna discharge unit as close as possible to where lead in enters house d Use jumper wire not smaller than No 6 AWG 13 3mm2 copper or the equivalent when a separate antenna grounding electrode is used see NEC Section 810 21 j EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE INSTRUCTIONS CONTAINED IN ARTICLE 810 RADIO AND TELEVISION EQUIPMENT SERVICE UY ENTRANCE CONDUCTORS SERVICE ENTRANCE EQUIPMENT MAST X LAMPS TS GROUND CLAMPS LEADAN WIRE DISCHARGE NS wene T EXTERNAL GROUND TERMINALS CLAMPS OF PRODUCT OPTIONAL ANTENNA GROUND DRIVEN FEET 2 44M
12. fessional what they think makes a great studio monitor and you ll get basically the same answers Accuracy transparency flat response and the truth Simply put recording engineers want the electrical signal entering their monitor to be reproduced mechanically by the transducers and they want this to occur without any deviation or compromise to the original signal Professionals depend upon their monitors to deliver their artistic vision in a way that will translate as accurately as possible to a variety of audio mediums Technically this is accomplished by designing a monitor that addresses three critically important criteria Spectral Balance Distortion Management and Resonance Management 1 Spectral Balance Timbre Research confirms that proper spectral balance is important for a studio monitor Spectral balance is defined by e Smooth on axis response e Smooth octave to octave response Smooth off axis response From years of listening to feedback from some of the top engineers and producers KRK engineers have come to understand how a properly tuned monitor can become a valuable recording tool The VXT monitors have been designed to be as flat as possible so that what you hear represents the true nature of the audio material without coloration or enhancement You can be confident in the fact that your mixes will be accurate and phase coherent 2 Distortion Management Any loss or addition to the audio signal is a distortion
13. he speaker system Active Filter Crossovers The VXT series power amplifiers contains three active filters Subsonic low pass and high pass filter These three filters work together to provide a seamless integration of the driver components ensuring a smooth spectral balance Bi amplifier Design KRK s amplifier consists of audiophile grade components and a simple audio path for transparency Output power is balanced to match LF and HF driver sensitivities and power handling Your VXT monitors use a toroidal power transformer for low hum and minimum noise Contoured Faceplate Like the KRK flagship close field monitor the Expos all cabinet edges and port openings are heavily contoured to reduce diffraction resulting in better detail and stereo imaging The curved faceplate offers improved off axis dispersion aiding in off axis imaging Slotted Ports Slotted ports reduce the port turbulence and distortion commonly found in poorly designed round ports Defeatable Limiter The monitors contain a limiter circuit which provides improved protection The Default setting for this switch will be in the OFF position The limiter is designed to mitigate the negative effects of over driving the amplifier and or the speaker s drivers The lim iter when engaged can greatly reduce the risk of harming a driver It can however be defeated using the Clip Indicator Limiter Switch on the rear panel This is only recommended if you are using your mon
14. is plugged snugly into the IEC socket on the rear of the monitor Check the connections between the signal source and the monitor The Neutrik amp Combo connector is a completely balanced system If you re connecting an unbalanced output to the monitor be sure that you re using PIN 2 for signal and have PIN 1 and PIN 3 tied together at the source end This can be done by using the appropriate cable or adapter All audio equipment should use the same ground point Check all other devices using the same AC output in the building like dimmers neon signs TV screens and computer monitors These devices should not be using the same circuit For updated Troubleshooting information please visit our Web Site www krksys com KRKCustomer Support can be reached at 954 316 1580 www americanmusical com 13 Please retain and read the warranty card information that was included in the shipping carton of your monito Before shipping your unit back to KRK for service you must acquire an RMA from KRK Your unit will not be received by the company nor will any work be done on your unit without this very important number Please call KRK at 954 316 1580 Shipping Instructions For the safest possible return to KRK please use the shipping carton and packaging that your KRKmonitor originally shipped in KRK cannot be responsible for any damages incurred during the shipping process due to poor packing Make sure to insure your shipment elf y
15. itors well within their limitations Use the indicator on the front baffle to help determine the optimum level without audible distortion Www americanmusical com 5 Back Panel Features ina ORE eR 0 SYSTEM le LEVEL ADJUST zs 30 dB 6 P 22i A SYSTEM LEVEL ADJUST OO 4 919 n HS Input sensitivity is adjusted counterclock Bg me E wise reduces sensitivity through a rear e a 4 09 panel mounted trim control Adjustment range is from 30dB to 6dB Factory preset gain is 6dB which should suffice for most woe EE conditions Normally adjustments would ust only be made if you re using your VXT monitors in a surround system and you need e 9 to balance levels or if your monitor source is too hot and not adjustable B HF ADJUSTMENT VXT 6 and VXT 8 ONLY High Frequency Adjustment is through a rear panel mounted 3 position toggle switch Range of control is 1dB Flat or 1dB shelving above 2 kHz Factory setting is flat toggle switch is in middle position Room acoustics may dictate which type of adjustment you need to make to retain the proper frequency response from the monitor O 4 1dB HF SHELF O4 FLAT o 4 1dB HF SHELF HF ADJUST Okt B LF ADJUSTMENT VXT 6 and VXT 8 ONLY This 3 way switch adjusts the low frequency response of the monitors Proximity to walls can add undesirable low f
16. ll unmute when signal is detected If you are working with very low level or intermittent material such as audio for games or surround mixing it is recommended to leave the auto mute switch off NEUTRIK amp COMBO CONNECTOR The Neutrik amp Combo connector accommodates XLR 1 4 TRS and 1 4 phone plugs Please note SIGNAL INPUT that PIN 2 is hot If you are using an 10K OHMS BALANCED unbalanced connection make sure to wire Sleeve _ PIN I SLEEVE GROUND and Ring together at the source end This can be PIN 2 TIP HIGH PIN 3 RING LOW accomplished by using the appropriate cable or adapter Installing Your Monitors The close field monitor by definition reduces room interaction This can be compared to the conventional stereo configuration or the large monitor arrangement in a recording studio where sounds emanating from the monitor or reflecting off ceilings walls and floors greatly affect the sound quality By shortening the path to the ear the close field monitor offers a tremendous amount of flexibility allowing the sound to become less susceptible to differing room conditions The ability to adjust the high and low frequency characteristics is equally important to help compensate for room irregularities and achieve the highest sound accuracy See HF Adjustments and LF Adjustments sections in this manual Note These adjustments are only available on the VXT 6 and VXT 8 A room that is heavily dampened w
17. nded Low Frequency Enclosure Design The cabinetry of your VXT monitor is constructed from ABS Structural Foam which provides stronger structural integrity compared to cabinets made from standard ABS solid materials Because of the increased strength of this process the cabinet walls can be thinner than would be from using MDF increasing the interior volume of the cabinet which equates to extended low frequency response Structural foam also provides enhanced dampening characteristics which greatly reduces cabinet resonance New cabinet design provides many benefits Due to the radical design of the cabinet your VXT monitors are manufactured using ABS Structural Foam The Cabinet has inner and outer walls with a lightweight foam filling ABS Structural Foam has many advantages over the standard ABS enclosure One advantage is the Cabinet can be made with thicker walls Having the foam between the inner and outer hard shells acts as a damper and reduces the potential of resonances Another advantage is that the walls can be thinner than they would be in MDF This allows for more internal volume allowing the system to extend its lower frequency capability The third advantage is that there are no parallel internal walls This eliminates standing waves and or nodes which are extremely detrimental to the internal and external acoustical response of an enclosure These characteristics aid in eliminating the cabinet from potentially coloring the sound of t
18. ould typically require a high frequency boost Likewise reducing the high frequencies can alter a reverberant room The low frequency can be adjusted to compensate for the first reflection bounce off the woofer whether it comes from the floor as in the typical stereo setup or from the surface of the mixing board when the monitor is placed atop the meter bridge Placing the monitor close to a rear wall sidewall or a corner will reinforce the low frequencies Generally speaking if you move them two to three feet away from walls and corners you ll hear less low frequency interaction excluding any interaction with the mixing console But when ideal positioning isn t practical low frequency control is the solution Lets say you have two different studios in your facility in one room the monitors are close to the wall in the other they re further away from the wall Simply adjust the low frequency on each monitor and you ll have the same sound in each room This comes in handy if you re tracking in room A and mixing down in room B Positioning Your Monitors Positioning the monitors correctly in the studio is critical to their performance Basically they should be placed in such a way that the listening position is fully covered with all speakers resting on the same horizontal plane A good way to test the monitor for its imaging capability is to play back a CD that you are very familiar with You can adjust the angle of each speaker b
19. our monitor is out of warranty and you would like a quotation prior to servicing your product please call for an RMA number No service will be performed on your unit without this number Replacement carton and packaging can be purchased from KRK Systems LLC for 26 50 each For replacement part quotes call 954 316 1580 www americanmusical com 14 Www americanmusical com Specifications Model VXT 4 VXT 6 VXT 8 Tweeter 1 Silk Dome NEO 1 Silk Dome Ferrite 1 Silk Dome Ferrite Woofer 4 Woven Kevlar 6 Woven Kevlar 8 Woven Kevlar LR 1 4 TRS Combo 10k Ohm Blanced Pin 1 Sleeve Ground Pin 2 Tip High Pin 3 Ring Low Input Type System Level Adjust 6dB to 30dB Variable Ground Lift LFT On or GND Off Clip Indicator On Off or Limit Controls Auto Mute On or Off IHF Adjust N A LF Adjust N A IHF 15 Watts LF 30 Watts 0A 100VAC 50HZ 0A 110 120VAC 50 60Hz 1 0A 220 240VAC 50 60Hz Amp amp Fusing Max SPL Music 104dB Peak 107dB Dimensions Shipping Weight 114 Ibs Omni Mount Part 20 5 WBX 30 0 WBX 13 5mm Min 20 0mm Max Screw Type Screw Length 10 1 16 H x7 1 33 W x7 D 12 5mm Min 17 5mm Max IXLR 1 4 TRS Combo 10k Ohm Blanced Pin 1 Sleeve Ground System Level Adjust 6dB to 30dB Variable Ground Lift LFT On or GND Off Clip Indicator On Off or Limit Auto Mute On or Off IHF Adjust 1dB Flat 1dB LF A
20. ource output and the monitor input The System Gain pot is turned up fully clockwise 6 dB The signal source E g mixing console work station CD player etc is turned up to a level that can properly send a signal to the monitors f one of the monitors is working Exchange the audio input cable from the non working monitor to the working unit This will determine whether it s really the monitor a faulty cable or some other glitch in the audio chain e f the monitor is still not responding it should be returned to the dealer that you purchased it from or to KRK for servicing Problem If the monitor suddenly stops working Turn the monitor down or off Repeat steps in the troubleshooting sections above before continuing to the next steps Carefully check to see if the amplifier s back plate is hot If the monitor has been running at it s highest power output for an extended period of time it could be that the unit has become overheated and the protection circuitry has shut the system down momentarily Your KRK monitor provides maximum circuitry protection against AC power surges amplifier overdrive and overheating of the amplifiers Turn the monitor off then wait 30 minutes to allow the back plate to cool down Turn the power switch back on Increase the volume to check for normal operation f the monitor is still not responding it should be returned to the dealer that you purchased it from or to KRK for servi
21. requency content Adjust the LF Adjustment switch to compensate for exaggerated low frequency response Room acoustics may dictate which type of adjustment you need to make to retain the proper frequency response from the monitor 6 www americanmusical com www americanmusical com R O 4 WHOLE NORMAL QUARTER Q 4 ir The three way toggle switch provides the ability to adjust the low frequency when the monitors are effected by by room boundaries such as walls and corner locations The setting labeled WHOLE refers to the term Whole Space and is used to provide the most bass response QUARTER refers to quarter space and rolls off the most low frequencies HALF refers to Half Space and provides a setting in between no roll off and QUARTER space roll off Your monitors come from the factory set to WHOLE space Read further in this document for more advice on set up 10 0 LF ADJUST 100 200 C Clip Indicator Limiter Switch The Clip Indicator Limiter switch allows you to choose between three options 1 In the On position the clip led RED is active and the limiter is bypassed At the onset of the red LED illuminating the amplifier is close to clipping When the red LED blinks occasionally and lightly no damage is occurring to your monitor If the red LED is lit for extended periods of time please turn down the input signal to your monitors to avoid damage
22. st all the monitors to match your lowest SPL reading Your system levels should now be balanced for multi channel surround Figure 4 On XS Www americanmusical com 11 Troubleshooting Problem If there is no power check to see if The power cord is plugged into both the IEC socket on the rear panel of the unit and into the AC mains The AC mains voltage is matched to the operating voltage requirements See Changing Voltage in the Connecting the System section on page 3 If the AC mains voltage is higher than your monitor s selected voltage it is possible that the fuse needs to be replaced See Changing Fuses in the Connecting the System section on page 3 The KRK logo on the front panel will be illuminated when the monitor is on If logo is not illuminated turn the powe switch OFF and check the A C mains fuse s NEVER USE A LARGER AMPERAGE FUSE THAN IS SPECIFIED Turn the power switch back on The power light should illuminate elf a fuse change was needed and upon powering the monitor back up the fuse s blow s again the monitor needs to be returned to the dealer you purchased it from or to KRK for servicing Problem If you can t hear any sound Repeat steps in the previous troubleshooting section above before continuing to the next steps eCheck to see if all other audio devices using the same AC outlet are still operating Make sure that The audio source cable is plugged into both the s
23. wer cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories manufacturer 12 Use only with the art stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug the apparatus during lightening storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally ot has been dropped NOORWONA specified by the ATTENTION POUR VITER LES CHOC ELECTRIQUES INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU AU FOND CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT If an indoor antenna is used either built into the set or installed separately never allow any part of the antenna to touch the metal parts of other electrical appliances such as a lamp TV set etc CAUTION POWER LINES Any outdoor antenna must be located away from all power lines OUTDOOR ANTENNA GROUNDING If an outside ant
24. y listening for dead spots where you ll notice an immediate decrease in high frequency content www americanmusical com Www americanmusical com 2 CHANNEL SET UP ALAA A SS Close Field Configuration In a control room situation the monitors are often times placed on the meter bridge or in a close field listening position Initial placement starts by measuring out a simple equilateral triangle all three sides equal in length with the apex at the center of the listening position as shown in Figure 1 as an overlay for the stereo installation In this configuration the Left and Right monitors are each placed at a 60 angle equidistant from the listening position Figure 1 Listening Position Mid Field Configuration This configuration is basically the same as the Close Field set up see Figure 2 It is normally used with larger monitors or when the monitors are too large or heavy for the meter bridge This set up has the potential for a larger sweet spot and better spatial imaging Make sure that the height of the woofer is above height of the console s meter bridge Figure 2 Subwoofer Setup Begin by determining the best location for your subwoofer If possible the optimum set up would look like the set up in Figure 3 however this setup may not be practical or possible in your room Once you have set up your monitors listen to some program material that you know contains low frequency inform
Download Pdf Manuals
Related Search