MS-98A9 - Rosch Computer GmbH
Contents
1. MS 98A9 Slot PCI E Peripheral Component Interconnect Express Slot The PCIE slot supports the PCIE interface expansion card PCI Peripheral Component Interconnect Slot The PCI slot supports LAN card SCSI card USB card and other add on cards that comply with PCI specifications 32 bit PCI Slot When adding or removing expansion cards make sure that you unplug the power supply first Meanwhile read the documentation for the expansion card to configure any necessary hardware or software settings for the ex pansion card such as jumpers switches or BIOS configuration 2 19 Hardware Setup ISA Industry Standard Architecture Slot The ISA slot supports the ISA interface expansion card Mini PCI E Slot The Mini PCI E slot is provided for wireless LAN card TV tuner card and Robson NAND Flash card mSATA Slot The mSATA slot is provided for mSATA SSD device Chapter 3 BIOS Setup This chapter provides information on the BIOS Setup program and allows you to configure the system for optimum use You may need to run the Setup program when m An error message appears on the screen during the system booting up and requests you to run SETUP m You want to change the default settings for customized features BIOS Setup Entering Setup Power on the computer and the system will s2. Deep S5 The setting enables disables the Deep S5 power saving mode S5 is almost the same as G3 Mechanical Off except that the PSU still supplies power at a minimum to the power button to allow return to SO A full reboot is required No previous content is retained Other components may remain powered so the computer can wake on input from the keyboard clock modem LAN or USB device gt Resume On USB PS2 from S3 S4 The item allows the activity of the USB PS2 device to wake up the system from S3 S4 sleep state gt Resume On OnChip GbE This field specifies whether the system will be awakened from power saving modes when activity or input signal of onboard LAN is detected Resume On PCIE PCI PME This field specifies whether the system will be awakened from power sav ing modes when activity or input signal of onboard PCIE PCI PME is de tected This field specifies whether the system will be awakened from power saving modes when activity or input signal of onboard LAN mini PCI E is detected gt Resume On RTC When Enabled your can set the date and time at which the RTC real time clock alarm awakens the system from suspend mode 3 21 BIOS Setup Exit Aptio Setup Utility Copyright C 2012 American Megatrends Inc Save Changes and Reset Save Changes and Exit Save changes to CMOS and exit the Setup Utility Discard Changes and Exit Abandon all changes and exit
3. MS 98A9 v1 x Industrial Computer Board 04307605889 E Preface Copyright Notice The material in this document is our intellectual property We take every care in the preparation of this document but no guarantee is given as to the correctness of its contents Our products are under continual improvement and we reserve the right to make changes without notice Trademarks All trademarks are the properties of their respective owners E NVIDIA is registered trademark of NVIDIA Corporation ATI is registered trademark of ATI Technologies Inc AMD is registered trademarks of AMD Corporation Intel is registered trademarks of Intel Corporation Windows is registered trademarks of Microsoft Corporation AMI is registered trademark of Advanced Micro Devices Inc Award is a registered trademark of Phoenix Technologies Ltd Realtek is registered trademark of Realtek Semiconductor Corpora tion Revision History Revision Revision History Date V1 0 For PCB v1 x 2012 08 MS 98A9 Safety Instructions Always read the safety instructions carefully Keep this User s Manual for future reference Keep this equipment away from humidity Lay this equipment on a reliable flat surface before setting it up The openings on the enclosure are for air convection hence protects th
4. reroute the shared ports Note This would be the recommended mode when BIOS does NOT have xHCI pre boot support 3 8 MS 98A9 Enabled All shared ports are eventually routed to the xHCI control ler during the BIOS boot process If BIOS does NOT have pre boot support for the xHCI controller it should initially route the sharable ports to the EHCI controller and then prior to OS boot it should route the ports to xHCI controller Note OS has to provide support for the xHCI controller in this mode If the OS does not provide sup port all sharable ports will not work Disabled The USB 3 0 ports are routed to the EHCI controller and the xHCI controller is turned off All USB 3 0 devices function as High Speed devices regardless of xHCI software support avail ability Legacy USB Support Set to Enabled if you need to use any USB 1 1 2 0 device in the operating system that does not support or have any USB 1 1 2 0 driver installed such as DOS and SCO Unix Audio Controller This setting enables disables the onboard audio controller gt Launch OnChip Lan OpROM Launch OnBoard Lan OpROM These settings enable disable the initialization of the onchip onboard PXE Boot ROM during bootup Selecting Disabled will speed up the boot process CPU Configuration Aptio Setup Utility Copyright C 2012 America Active Processor Cores gt Active Processor Cores This setting allows user to select the nu
5. be activated The system will record this status and show a warning message on the screen To clear the warning you must enter the BIOS utility and clear the record T VBAT 2 INTR_ALERT Serial ATA Connector SATA1 SATA5 This connector is a high speed Serial ATA interface port Each connector can connect one Serial ATA device lgporieni Please do not fold the Serial ATA cable into 90 degree angle Otherwise data loss may occur during transmission Hardware Setup TPM Module Connector JTPM1 This connector connects to a TPM Trusted Platform Module Please refer to the TPM security platform manual for more details and usages Fan Power Connector CPUFAN1 SYSFAN1 SYS FAN2 SYSFAN3 The fan power connector supports system cooling fan with 12V When connecting the wire to the connectors always note that the red wire is the positive and should be connected to the 12V the black wire is Ground and should be connected to GND If the mainboard has a System Hardware Monitor chipset onboard you must use a specially designed fan with speed sensor to take advantage of the CPU fan control gt gt A Ss lt gt e ESE US 7 33 40701458 asso i lt 28 e lt ee CPUFAN1 SYSFAN1 3 Important Please refer to the recommended CPU fans at processor s official website or consult the vendors for proper CPU cooling fan MS 98A9 GPIO Pinheader JGPIO1 This connector is provid
6. producten 2002 96 EC die op 13 Augustus 2005 in zal gaan kunnen niet meer beschouwd worden als vervuiling Fabrikanten van dit soort producten worden verpli cht om producten retour te nemen aan het eind van hun levenscyclus Preface SRPSKI Po Direktiv Evropske unije EU o odbacenoj ekektronskoj i elektri noj opremi Di rektiva 2002 96 EC koja stupa na snagu od 13 Avgusta 2005 proizvodi koji spadaju pod elektronsku i elektri nu opremu ne mogu vise biti odba eni kao obi an otpad i proizvo a i ove opreme bi e prinu eni da uzmu natrag ove proizvode na kraju njihovog uobi ajenog veka trajanja POLSKI Zgodnie z Dyrektyw Unii Europejskiej UE dotycz c odpad w produkt w elektry cznych i elektronicznych Dyrektywa 2002 96 EC kt ra wchodzi w ycie 13 sierpnia 2005 tzw produkty oraz wyposa enie elektryczne i elektroniczne nie mog by trak towane jako mieci komunalne tak wi c producenci tych produkt w b d zobowi zani do odbierania ich w momencie gdy produkt jest wycofywany z u ycia T RK E Avrupa Birli i AB Kararnamesi Elektrik ve Elektronik Malzeme At 2002 96 EC Kara rnamesi alt nda 13 A ustos 2005 tarihinden itibaren ge erli olmak zere elektrikli ve elektronik malzemeler di er at klar gibi pe at lamayacak ve bu elektonik cihazlar n reticileri cihazlar n kullan m s releri bittikten sonra r nleri geri toplamakla y k ml olaca
7. setting enables disables the specified serial port Change Settings Serial Port 1 2 3 4 5 6 This setting is used to change the address amp IRQ settings of the specified serial port Mode Select Select an operation mode for the serial port 1 2 Parallel Port This setting enables disables the specified Parallel Port Change Settings This setting is used to change the address 8 IRA settings of the specified Parallel Port Device Mode Select an operation mode for the Parallel Port gt FIFO Mode Select a mode for the Parallel Port Watch Dog Timer You can enable the system watch dog timer a hardware timer that generates a reset when the software that it monitors does not re spond as expected each time the watch dog polls it Hardware Health Configuration Aptio Setup Utility Copyright C 2012 3 11 BIOS Setup Smart Fan Configuration Aptio Setup Utility Copyright C 2012 CPUFAN Type 3 Pin gt CPUFAN Type This setting specifies the fan type Smart CPUFAN SYSFAN1 2 3 Function This setting enables disables the Smart Fan function Smart Fan is an excellent feature which will adjust the CPU system fan speed automati cally depending on the current CPU system temperature avoiding the overheating to damage your system gt GPIO Configuration Aptio Setup Utility Copyright C 2012 GPOO Data GPO 0 1 2 3 Data This setting specifies
8. the GPO data 3 12 MS 98A9 Boot Aptio Setup Utility Copyright C 2012 American Megatrends Inc Boot Option 1 JetFlashTS8GJIFV10 8 07 gt Boot Option 1 2 3 This setting allows users to set the sequence of boot devices where BIOS attempts to load the disk operating system gt Hard Drive BBS Priorities This setting allows users to set the priority of the specified devices First press lt Enter gt to enter the sub menu Then you may use the arrow keys 1 to select the desired device then press lt gt lt gt or lt PageUp gt lt Page Down gt key to move it up down in the priority list 3 13 BIOS Setup Security Aptio Setup Utility Copyright C 2012 American Megatrends Inc Administrator Password Administrator Password Administrator Password controls access to the BIOS Setup utility User Password User Password controls access to the system at boot and to the BIOS Setup utility Chassis Intrusion The field enables or disables the feature of recording the chassis intrusion status and issuing a warning message if the chassis is once opened To clear the warning message set the field to Reset The setting of the field will automatically return to the default value later 3 14 MS 98A9 gt Trusted Computing Aptio Setup Utility Copyright C 2012 Security Device Support Disable Security Device Support This se
9. the Setup Utility Discard Changes Abandon all changes gt Optimized Defaults Use this menu to load the default values set by the mainboard manufacturer specifically for optimal performance of the mainboard Save as User Defaults Save all changes as user defaults Restore User Defaults Restore the preset user defaults 3 22
10. 2 Shielded interface cables and AC power cord if any must be used in order to comply with the emission limits VOIR LA NOTICE D INSTALLATION AVANT DE RACCORDER AU RESEAU This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation MS 98A9 WEEE Statement ENGLISH Under the European Union EU Directive on Waste Electrical and Elec tronic Equipment Directive 2002 96 EC which takes effect on August 13 a 2005 products of electrical and electronic equipment cannot be discarded as municipal waste anymore and manufacturers of covered electronic equipment will be obligated to take back such products at the end of their useful life DEUTSCH Gem der Richtlinie 2002 96 EG Uber Elektro und Elektronik Altger te d rfen Elektro und Elektronik Altgerate nicht mehr als kommunale Abfalle entsorgt werden Wir haben europaweit verschiedene Sammel und Recyclingunternehmen beauftragt die in die Eu ropaische Union in Verkehr gebrachten Produkte am Ende seines Lebenszyklus zur ck zunehmen Bitte entsorgen Sie dieses Produkt zum gegebenen Zeitpunkt ausschliesslich an einer lokalen Altgeratesammelstelle in Ihrer Nahe FRANCAIS Au sujet de la directive europ enne EU relative aux d chets des quipe
11. 3 6 Components Reference Guide Port Type LGA 1155 CPU Socket DDR3 Memory Slots ATX 24 pin Power Connector ATX 8 pin Power Connector I O Ports Fan Power Connectors Front Panel Audio Connector Clear CMOS Jumper Chassis Intrusion Connector Serial Port Connector Voice Genie Connector Front Panel Connectors Parallel Port Connector TPM Module Connector MultiConnect Panel Connector USB 2 0 Expansion Connectors USB 3 0 Expansion Connector PCI Expansion Slots PCle x16 Expansion Slots PCle x1 Expansion Slots SATA 6Gb s Connector SATA 6Gb s or 3Gb s Connector SATA 3Gb s Connectors Page 2 4 2 7 2 8 2 9 2 19 2 23 2 26 2 22 2 24 2 25 2 20 2 24 2 23 2 25 2 22 2 21 2 17 2 16 2 16 2 18 2 18 2 18 MS 98A9 CPU Central Processing Unit When you are installing the CPU make sure that you install the cooler to prevent overheating If you do not have the CPU cooler consult your dealer before turning on the computer Overheating Overheating will seriously damage the CPU and system Always make sure the cooling fan can work properly to protect the CPU from overheating Make sure that you apply an even layer of thermal paste or thermal tape between the CPU and the heatsink to enhance heat dissipation Replacing the CPU While replacing the CPU always turn off the power supply or unplug the power supply s power cord from the grounded outlet first to ensure the safety of CPU Introdu
12. 55 Intel Q77 PCH Support iAMT 8 0 4 DDR3 1066 1333 1600 SO DIMM slots Supports the maximum of 32GB Gigabit Fast Ethernet by Intel 82579LM PHY amp 82583V GbE controllers 3 SATA 3Gb s ports by Intel Cougar Point 2 SATA 6Gb s ports by Intel Cougar Point SATA1 5 support Intel Rapid Storage Technology AHCI RAID 0 1 5 10 by Intel Panther Point HDA Codec by Realtek ALC887 Compliant with Azalia 1 0 specs Support by the installed processor Support 3 independent displays by Ivy Bridge series Support 2 independent displays by Sandy Bridge series 1 PS 2 mouse keyboard port 1 VGA port 1 DVI D port 1 serial port 1 Displayport 2 Gigabit LAN jacks 2 USB 2 0 ports 4 USB 3 0 ports 1 Line In audio jack 1 Line Out audio jack 1 Mic In audio jack 1 2 MS 98A9 3 USB 2 0 pinheaders 5 serial port connectors 1 GPIO pinheader 1 front audio pinheader 1 chassis intrusion pinheader 1 Parallel port pinheader 1 TPM module connector optional 1 front panel pinheader 1 PCle x16 slot 1 PCle x4 slot 1 Mini PCle slot 1 mSATA slot 5 PCI slots 1 ISA slot ATX 305mm x 244mm Operating Temperature 0 C to 60 C Storage Temperature 20 C to 80 C Humidity 5 95 RH Non Condensing 1 3 Overview Mainboard Layout 490705895 IN 043076058897 III PCI E Slot me PCI S Slot Front Audio Header Serial Port Con nector Fan Power
13. Receive Data Negative 5 GND Signal Ground 6 NC No Connection 7 NC No Connection 8 NC No Connection 9 NC No Connection RS 485 PIN SIGNAL DESCRIPTION 1 485 TXD Transmit Data Negative 2 NC No Connection 3 485 TXD Transmit Data Positive 4 NC No Connection 5 GND Signal Ground 6 NC No Connection 7 NC No Connection 8 NC No Connection 9 NC No Connection 2 9 Hardware Setup gt LAN The standard RJ 45 LAN jack is for connection to the Local Area Network LAN You can connect a network cable to it Left LED Right LED Left LED Right LED Active LED 100M 1000M Speed LED LED Color Orange Green Yellow 10M Cable No Transmission Orange Lighting OFF Ege Transmission Orange Blinking OFF 100M Cable No Transmission Orange Lighting Green Lighting Pugin Transmission Orange Blinking Green Lighting 1000M Cable No Transmission Orange Lighting Yellow Lighting Pigan Transmission Orange Blinking Yellow Lighting In S3 S4 S5 Standby State Orange Lighting OFF gt Audio Jack m Line in Blue for external CD player or other audio devices m Line Out Green for speakers or headphones m Mic In Pink for microphones 2 10 MS 98A9 Connector Chassis Intrusion Pinheader Cl1 This connector is provided to connect the chassis intrusion switch cable If the chassis is opened the chassis intrusion mechanism will
14. Selection This setting specifies the SATA controller mode 3 6 MS 98A9 Advanced Aptio Setup Utility Copyright C 2012 American Megatrends Inc Full Screen Logo Display Disabled gt Full Screen Logo Display This BIOS feature determines if the BIOS should hide the normal POST messages with the motherboard or system manufacturer s full screen logo When it is enabled the BIOS will display the full screen logo during the boot up sequence hiding normal POST messages When it is disabled the BIOS will display the normal POST messages in stead of the full screen logo Please note that enabling this BIOS feature often adds 2 3 seconds of delay to the booting sequence This delay ensures that the logo is displayed for a sufficient amount of time Therefore it is recommended that you disable this BIOS feature for a faster boot up time Bootup NumLock State This setting is to set the Num Lock status when the system is powered on Setting to On will turn on the Num Lock key when the system is powered on Setting to Off will allow users to use the arrow keys on the numeric keypad 3 7 BIOS Setup Option ROM Messages This item is used to determine the display mode when an optional ROM is initialized during POST When set to Force BIOS the display mode used by AMI BIOS is used Select Keep Current if you want to use the display mode of optional ROM gt PCI PCIE Devi
15. ce Configuration Aptio Setup Utility Copyright C 2012 American PCI Latency Timer 32 PCI Bus Clocks PCI Latency Timer This item controls how long each PCI device can hold the bus before another takes over When set to higher values every PCI device can conduct transactions for a longer time and thus improve the effective PCI bandwidth For better PCI performance you should set the item to higher values gt EHCI1 EHCI2 These settings disable enable the USB EHCI controllers The Enhanced Host Controller Interface EHCI specification describes the register level interface for a Host Controller for the USB 2 0 gt xHCI Mode This setting allows user to determine the operating mode for the xHCI controller in the operation system There are four options m Smart Auto This mode is available when the BIOS supports xHCI controller in pre boot environment This mode is similar to Auto mode but it is with capability to route the ports to xHCI or EHCI according to setting used in previous boots for non G3 boot in the pre boot environment This allows the use of USB 3 0 devices prior to OS boot When previous boot routs ports to EHCI xHCl controller enabling and rerouting should follow the steps in Auto Note This would be the recommended mode when BIOS has xHCl preboot support Default m Auto BIOS routes shared ports to EHCI controller And it uses ACPI protocols to provide an option to enable xHCI controller and
16. ction to LGA 1155 CPU The surface of LGA 1155 CPU Remember to apply some thermal paste on it for better heat dispersion Alignment Key Alignment Key Yellow triangle is the Pin 1 indicator 2 3 Hardware Setup CPU Cooler Installation When you are installing the CPU make sure the CPU has a cooler at tached on the top to prevent overheating Meanwhile do not forget to apply some thermal paste on CPU before installing the heat sink cooler fan for better heat dispersion Follow the steps below to install the CPU amp cooler correctly Wrong instal lation will cause damage to your CPU 8 mainboard 1 Open the load lever 2 Lift the load lever up to fully open position 3 After confirming the CPU 4 Remove the plastic cap direction for correct mating Engage the load lever while put down the CPU in the pressing down lightly onto socket housing frame Be the load plate sure to grasp on the edge of the CPU base Note that the alignment keys are matched Visually inspect if the CPU is seated well into the socket If not take out the CPU with pure vertical motion and reinstall MS 98A9 5 Secure the lever near the 6 Make sure the four hooks are hook end under the reten in proper position before you tion tab install the cooler Align the holes on the mainboard with the cooler Push down the cooler until its four clips get wedged into the holes of the mainboard 7 Pres
17. den finger if the memory module is properly inserted in the DIMM slot The plastic clip at each side of the DIMM slot will automatically close luparen DDR3 memory modules are not interchangeable with DDR2 and the DDR3 standard is not backwards compatible You should always in stall DDR3 memory modules in the DDR3 DIMM slots To enable successful system boot up always insert the memory mod ules into the DIMM1 first MS 98A9 Power Supply 24 Pin Power Connector JPWR1 This connector allows you to connect an 24 pin power supply To connect the 24 pin power supply make sure the plug of the power supply is inserted in the proper orientation and the pins are aligned Then push down the power supply firmly into the connector 4 Pin Power Connector JPWR2 This 12V power connector is used to provide power to the CPU Make sure that all the connectors are connected to proper ATX power sup plies to ensure stable operation of the mainboard 2 7 Hardware Setup Back Panel I O Mouse Keyboard Port Serial Port USB 2 0 Displayport DVI D Port USB 3 0 USB 3 0 Port Port Port gt Mouse Keyboard Port The standard PS 2 mouse keyboard DIN connector is for a PS 2 mouse keyboard gt VGA Port The DB15 pin female connector is provided for monitor gt DVI D Port The DVI D Digital Visual Interface Digital connector allows you to connect an LCD monitor It provides a high speed d
18. e equipment from overheating DO NOT COVER THE OPENINGS Make sure the voltage of the power source and adjust properly 110 220V before connecting the equipment to the power inlet E Place the power cord such a way that people can not step on it Do not place anything over the power cord E Always Unplug the Power Cord before inserting any add on card or mod ule E All cautions and warnings on the equipment should be noted E Never pour any liquid into the opening that could damage or cause electri cal shock E if any of the following situations arises get the equipment checked by ser vice personnel O The power cord or plug is damaged O Liquid has penetrated into the equipment O The equipment has been exposed to moisture O The equipment does not work well or you can not get it work according to User s Manual O The equipment has dropped and damaged O The equipment has obvious sign of breakage E DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDI TIONED STORAGE TEMPERATURE ABOVE 80 C 176 F IT MAY DAM AGE THE EQUIPMENT CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer SS FAMA RPTE EERGIRAPRRE aer CSS ESE ESTER Ll a For better environmental protection waste batteries should be Us collected separately for recycling or special disposal Preface CE Conformity Hereby w
19. e declare that this device is in compliance with the essential safety requirements and other relevant provisions set out in the European Directive FCC B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against C harmful interference in a residential installation This equip ment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications However there is no guar antee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the measures listed below E Reorient or relocate the receiving antenna E increase the separation between the equipment and receiver E Connect the equipment into an outlet on a circuit different from that to which the receiver is connected E Consult the dealer or an experienced radio television technician for help NOTICE 1 The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTICE
20. e sub menu Then you can use the control keys to enter values and move from field to field within a sub menu If you want to return to the main menu just press the lt Esc gt GENERAL HELP lt F1 gt The BIOS setup program provides a General Help screen You can call up this screen from any menu by simply pressing lt F1 gt The Help screen lists the appropriate keys to use and the possible selections for the highlighted item Press lt Esc gt to exit the Help screen 3 3 BIOS Setup The Menu Bar Aptio Setup Utility Copyright C 2012 American Megatrends Inc System Date 01 Main Use this menu for basic system configurations such as time date etc Advanced Use this menu to setup the items of special enhanced features Boot Use this menu to specify the priority of boot devices Security Use this menu to set supervisor and user passwords Chipset This menu controls the advanced features of the onboard Northbridge and Southbridge Power Use this menu to specify your settings for power management gt Save amp Exit This menu allows you to load the BIOS default values or factory default set tings into the BIOS and exit the BIOS setup utility with or without changes 3 4 MS 98A9 Aptio Setup Utility Copyright C 2012 American Megatrends Inc System Date 01 System Time This setting allows you to set the system time The time format is lt Hour g
21. ed this requires additional firmware in the SPI device 3 16 MS 98A9 gt BIOS Hotkey Pressed Enable Disable BIOS hotkey press gt MEBx Selection Screen Enable Disable MEBx selection screen Hide Un Configure ME Confirmation Hide Un Configure ME without password Confirmation Prompt gt MEBx Debug Message Output Enable MEBx debug message output gt Un Configure ME Un Configure ME without password gt Amt Wait Timer Set timer to wait before sending ASF_GET_BOOT_OPTIONS gt Disable ME To flash BIOS ROM the ME has to be disabled first gt ASF Enable Disable Alert Specification Format gt Activate Remote Assistence Process Trigger CIRA boot USB Configure Enable Disable USB Configure function gt PET Progress User can enable disable PET Events progress to received PET events or not gt WatchDog Enable Disable WatchDog Timer 3 17 BIOS Setup gt Serial Port Console Redirection Aptio Setup Utility Copyright C 2012 Console Redirection Disabled gt Console Redirection Enable Disable Console Redirection feature MS 98A9 Chipset Aptio Setup Utility Copyright C 2012 American Megatrends Inc Enabled gt VT d This item is used to enable disable the Intel Virtualization Technology for Directed UO For further information please refer to Intel official website gt Primary Display This setting specifies which
22. ed for the General Purpose Input Output GPIO peripheral module Front Panel Pinheader JFP1 This front panel connector is provided for electrical connection to the front panel switches amp LEDs and is compliant with Intel Front Panel I O Con nectivity Design Guide a a E o lt os o gt 2 lt a gt At gt gt e e Ss ke SCH 22 2 13 Hardware Setup Front USB Pinheader JUSB1 JUSB3 This connector compliant with Intel I O Connectivity Design Guide is ideal for connecting high speed USB interface peripherals such as USB HDD digital cameras MP3 players printers modems and the like USB 2 0 Bracket Optional Note that the pins of 5V and GND must be connected correctly to avoid possible damage MS 98A9 Serial Port Connector COM2 COM6 This connector is a 16550A high speed communications port that sends receives 16 bytes FIFOs You can attach a serial device to it through an optional serial port bracket ob 5 sy ko 5 A OL A tE zz PIN SIGNAL DESCRIPTION 1 NDCD Data Carrier Detect 2 NSIN Receive Data 3 NSOUT Transmit Data 4 NDTR Data Terminal Ready 5 GND Signal Ground 6 NDSR Data Set Ready 7 NRTS Request To Send 8 NCTS Clear To Send 9 VCC COM 12V or 5V power output selected by jumper 2 15 Hardware Setup Front Audio Pinheader JAUD1 This connector allows you to connect the front panel audio and is comp
23. igital interconnection between the computer and its display device To connect an LCD monitor simply plug your monitor cable into the DVI connector and make sure that the other end of the cable is properly connected to your monitor refer to your monitor manual for more information gt DisplayPort DisplayPort is a digital display interface standard This connector is used to connect a monitor with DisplayPort inputs gt USB 2 0 Port The USB 2 0 port is for attaching USB devices such as keyboard mouse or other USB compatible devices Supports data transfer rate up to 480Mbit s Hi Speed gt USB 3 0 Port USB 3 0 port is backward compatible with USB 2 0 devices It supports data transfer rate up to 5 Gbit s SuperSpeed MS 98A9 RS 232 422 485 Serial Port Connector Optional The serial port is a 16550A high speed communications port that sends receives 16 bytes FIFOs You can attach a serial mouse or other serial devices directly to the connector RS 232 PIN SIGNAL DESCRIPTION 1 DCD Data Carrier Detect 2 RXD Receive Data 3 TXD Transmit Data 4 DTR Data Terminal Ready 5 GND Signal Ground 6 DSR Data Set Ready 7 RTS Request To Send 8 CTS Clear To Send 9 VCC_COM1 Voltage select setting by J1 RS 422 PIN SIGNAL DESCRIPTION 1 422 TXD Transmit Data Negative 2 422 RXD Receive Data Positive 3 422 TXD Transmit Data Positive 4 422 RXD
24. is your primary graphics adapter gt DVMT Pre Allocated This setting defines the DVMT pre allocated memory Pre allocated mem ory is the small amount of system memory made available at boot time by the system BIOS for video Pre allocated memory is also known as locked memory This is because it is locked for video use only and as such is invisible and unable to be used by the operating system gt DVMT Total Gfx Mem This setting specifies the memory size for DVMT gt Primary Secondary IGFX Boot Display Use the field to select the type of device you want to use as the primary secondary display s of the system 3 19 BIOS Setup Power Aptio ACPI Sleep State gt ACPI Sleep State American Megatrends Inc Setup Utility Copyright C 2012 r g 53 only Suspend to RAM This item specifies the power saving modes for ACPI function If your oper ating system supports ACPI you can choose to enter the Standby mode in S1 POS or S3 STR fashion through the setting of this field gt Restore AC Power Loss This setting specifies whether your system will reboot after a power failure or interrupt occurs Available settings are Power Off Leaves the computer in the power off state Power On Leaves the computer in the power on state Last State Restores the system to the previous status before power failure or interrupt occurred 3 20 MS 98A9
25. kt r ESKY Podle sm rnice Evropsk unie EU o likvidaci elektrick ch a elektronick ch v robk 2002 96 EC platn od 13 srpna 2005 je zak z no likvidovat elektrick a elektronick v robky v b n m komun ln m odpadu a v robci elektronick ch v robk na kter se tato sm rnice vztahuje budou povinni odeb rat takov v robky zp t po skon en jejich ivotnosti MAGYAR Az Eur pai Uni EU 2005 augusztus 13 n hat lyba l p az elektromos s elektron ikus berendez sek hullad kair l sz l 2002 96 EK ir nyelve szerint az elektromos s elektronikus berendez sek t bb nem kezelhet ek lakoss gi hullad kk nt s az ilyen elektronikus berendez sek gy rt i k teless v lnak az ilyen term kek visszav tel re azok hasznos lettartama v g n ITALIANO In base alla Direttiva dell Unione Europea EU sullo Smaltimento dei Materiali Elettrici ed Elettronici Direttiva 2002 96 EC in vigore dal 13 Agosto 2005 prodotti appartenenti alla categoria dei Materiali Elettrici ed Elettronici non possono pi essere eliminati come rifiuti municipali i produttori di detti materiali saranno obbligati a ritirare ogni prodotto alla fine del suo ciclo di vita vi MS 98A9 Contents Copyright e os EE ii Bu EE ii Revision FNS E ii Safety ET e e iii CE EEN scan iv FCC B Radio Frequency Interference Giatement iv WEEE State MeNi cacsaccisasirnsceis veces etivnxssstisssdsarsuesi
26. liant with Intel Front Panel I O Connectivity Design Guide Parallel Port Header JLPT1 The mainboard provides a 26 pin header for connection to an optional paral lel port bracket The parallel port is a standard printer port that supports En hanced Parallel Port EPP and Extended Capabilities Parallel Port ECP mode 2 16 MS 98A9 Jumper Clear CMOS Jumper CLR CMOS1 There is a CMOS RAM onboard that has a power supply from an external battery to keep the data of system configuration With the CMOS RAM the system can automatically boot OS every time it is turned on If you want to clear the system configuration set the jumper to clear data 1 1060 OED CLR CMOS 1 Clear CMOS Keep CMOS lupeni You can clear CMOS by shorting 1 2 pin while the system is off Then return to 2 3 pin position Avoid clearing the CMOS while the system is on it will damage the mainboard ME Jumper ME_DIS1 This jumper is used to disable enable the Intel AMT ME technology 1 1 1 ME_DIS1 Enabled Disabled 2 17 Hardware Setup AT ATX Select Jumper JAT1 This jumper allows users to select between AT and ATX power dee CR BA JAT1 AT Power ATX Power COM Port Power Jumper JCOMP1 JCOMP6 These jumpers specify the operation voltage of the onboard serial ports a 1 E JCOMP1 6 5V 12V
27. m Gi Con nector COM Power Jumper Mouse Keyboard Port en USB 2 0 Port 4 pin Power Connector CPU aba EL y E i Tae j d E La nee CH di See I 3 E Ga BE uE d E 14 E E S ED n E ee HUDD ISA Slot Serial Port Displayport Fan Power Connector Duterte LAN Jack DIMM Slot ap i E sac SL Kc OO Mini PCI E Slot mSATA Slot AT ATX Jumper COM Power Jumper __ Serial Port Connector COM Power Jumper COM Power Jumper 24 pin Power Connector pa Fan Power Connector t Clear CMOS Kl Jumper SATA Connector BOLSNI 6863 GPIO Pinheader Chassis Intrusion AT Pinheader ntel AMT ME Jum Front USB Pinheader TPM Module connector Front Panel a S Pinheader arallel Port Pinheader 1 4 Chapter 2 Hardware Setup This chapter provides you with the information on mainboard hardware configurations Incorrect setting of jumpers and connectors may damage your main board Please pay special attention not to connect these headers in wrong direction DO NOT adjust any jumper while the mainboard is powered on Hardware Setup Port Name CPU DIMM1 4 JPWR1 JPWR2 Back Panel CPUFAN SYSFAN1 4 JAUD1 JBAT1 JCI1 JCOM1 JDLED3 JFP1 JFP2 JLPT1 JTPM1 JTURBO1 JUSB1 2 JUSB3 PCI 2 PCI E2 PCI E4 PCI E1 PCI E3 SATA1 SATA2 SATA
28. mber of cores to enable in each processor package Note that this field is present only when a multi core processor is installed 3 9 BIOS Setup Execute Disable Bit Intel s Execute Disable Bit functionality can prevent certain classes of mali cious buffer overflow attacks when combined with a supporting operating system This functionality allows the processor to classify areas in memory by where application code can execute and where it cannot When a mali cious worm attempts to insert code in the buffer the processor disables code execution preventing damage or worm propagation gt Intel Virtualization Tech Virtualization enhanced by Intel Virtualization Technology will allow a plat form to run multiple operating systems and applications in independent partitions With virtualization one computer system can function as mul tiple Virtual systems gt EIST EIST Enhanced Intel SpeedStep Technology allows the system to dy namically adjust processor voltage and core frequency which can result in decreased average power consumption and decreased average heat production When disabled the processor will return the actual maximum CPUID input value of the processor when queried gt Super IO Configuration Aptio Setup Utility Copyright C 2012 American Mel Serial Port 1 Enabled Watch Dog Timer Disabled 3 10 MS 98A9 gt Serial Port 1 2 3 4 5 6 This
29. ment lectriques et lectroniques directive 2002 96 EC prenant effet le 13 ao t 2005 que les produits lec triques et lectroniques ne peuvent tre d pos s dans les d charges ou tout simplement mis la poubelle Les fabricants de ces quipements seront oblig s de r cup rer certains produits en fin de vie Par cons quent vous pouvez retourner localement ces mat riels dans les points de collecte PYCCKUN B Coorpercrpuu c Dupekrupou Epponeuckormg Cosa EC no npenxoTBpaujeHuto 3arpa3HeHvua okKpykabwuje CDen UCNONb3OBAHHbIM 3NEKTPUYECKUM M INEKTPOHHbIM o6opyaoBaHnem qupektuBa WEEE 2002 96 EC sctynatowen B cuny 13 aprvcra 2005 roga u3qenua OTHOCALUMECA K INEKTPUYECKOMY N INEKTPOHHOMy O6OpyAOBaAHHO HE MOryT paccMaTpuBaTbca KaK GbITOBOH Mycop NOsTOMY NPOM3BOAHTENH BbILLIENEPEHMCNEHHOTO aNEKTPOHHOFoO OGOPYyAOBAHM5I O6A3aHbI NPHHUMATb ero ana Nepepa oTkn NO OKOHYaHun cpoka cryx6bl ESPA OL Bajo la directiva 2002 96 EC de la Uni n Europea en materia de desechos y o equipos electr nicos con fecha de rigor desde el 13 de agosto de 2005 los productos clasificados como el ctricos y equipos electr nicos no pueden ser depositados en los contenedores habituales de su municipio los fabricantes de equipos electr nicos est n obligados a hacerse cargo de dichos productos al termino de su per odo de vida NEDERLANDS De richtlijn van de Europese Unie EU met betrekking tot Vervuiling van Electrische en Electronische
30. s the four hooks down to 8 Finally attach the CPU Fan fasten the cooler Turn over cable to the CPU fan con the mainboard to confirm nector on the mainboard that the clip ends are cor rectly inserted i Ap e Confirm if your CPU cooler is firmly installed before turning on your system e Do not touch the CPU socket pins to avoid damaging e Whenever CPU is not installed always protect your CPU socket pin with the plastic cap covered to avoid damaging Please refer to the documentation in the CPU cooler package for more details about the CPU cooler installation 2 5 Hardware Setup Memory These DIMM slots are intended for memory modules DDR3 DOC OCA SA OCC DR DONNA nnnAnAnnnnannntonnnanonnnnnnnnannanaanannnnnannanna 240 pin 1 5V TTT OOO CTT y I Loo SE E 48x2 96 pin 72x2 144 pin Installing Memory Modules 1 The memory module has only one notch on the center and will only fit in the right orientation Insert the memory module vertically into the DIMM slot Then push it in until the golden finger on the memory module is deeply inserted in the DIMM slot You can barely see the gol
31. ssdrcsstr FERETE EEEE eE ETET Vv Chapter EEN 1 1 Mainboard Specifications eeeeeeeeeeen anneer te eeeeeerenerer rtnn rnrn nenene ne 1 2 Mainboard Layout E 1 4 Chapter 2 Hardware SetuPp ccccccceeeeeeeeeeeeseeneeeeeeeeeeeeeeeeeeeeeeeeeaeeeaes 2 1 Components Reference Guide AAA 2 2 A mmm Am mm m m Mm t mm 2 3 MEMO EE 2 6 Power SUpDly eecht a a a 2 7 Back Panel EK Ee EE 2 8 PP e a a 2 11 JUMPE EE 2 17 Slot eebe 2 19 Chapter 3 BIOS SEU Eed EE Seed 3 1 Entenng S6tUP saades kat teil ies 3 2 TheMenu E 3 4 MSI a E 3 5 Adyanced EE 3 7 PIG OE A EE E S 3 13 SS CUNY A SAA 3 14 I SG EE 3 16 POW GT ee 3 17 EE 3 19 vii Chapter 1 Overview Thank you for choosing MS 98A9 an excellent indus trial computer board Based on the innovative Intel Panther Point chip set for optimal system efficiency MS 98A9 sup ports Ivy Bridge and Sandy Bridge processor series in socket LGA1155 and supports up to four DDR3 1066 1333 1600 SO DIMM slots to provide the maxi mum of 32GB memory capacity In the advanced level and mid range market segment MS 98A9 provides a high performance solution for today s front end and general purpose workstation as well as in the future Overview CPU m Optional Chipset m H Memory m H LAN m SATA m H RAID m Audio m H Graphics 7 Back Panel I O Mainboard Specifications Intel Ivy Bridge series and Sandy Bridge series processor in socket LGA11
32. t lt Minute gt lt Second gt System Date This setting allows you to set the system date The date format is lt Day gt lt Month gt lt Date gt lt Year gt 3 5 BIOS Setup gt SATA1 SATAS Type Press PgUp lt gt or PgDn lt gt to select Manual None or Auto type Note that the specifications of your drive must match with the drive table The hard disk will not work properly if you enter improper information for this category If your hard disk drive type is not matched or listed you can use Manual to define your own drive type manually LBA Large Mode Enabling LBA causes Logical Block Address ing to be used in place of Cylinders Heads and Sectors Block Multi Sector Transfer Any selection except Disabled determines the number of sectors transferred per block PIO Mode Indicates the type of PIO Programmed Input Output DMA Mode S M A R T Indicates the type of Ultra DMA This allows you to activate the S M A R T Self Monitoring Analysis 8 Reporting Technol ogy capability for the hard disks S M A R T is a utility that monitors your disk status to predict hard disk failure This gives you an opportunity to move data from a hard disk that is going to fail to a safe place before the hard disk becomes offline 32 Bit Data Transfer Enables 32 bit communication between CPU and IDE controller gt SATA Mode
33. tart POST Power On Self Test process When the message below appears on the screen press lt DEL gt key to enter Setup PRESS DEL TO ENTER SETUP If the message disappears before you respond and you still wish to enter Setup restart the system by turning it OFF and On or pressing the RESET button You may also restart the system by simultaneously pressing lt Ctrl gt lt Alt gt and lt Delete gt keys Upon The items under each BIOS category described in this chapter are un der continuous update for better system performance Therefore the description may be slightly different from the latest BIOS and should be held for reference only CONTROL KEYS gt Select Screen al Select Item Change Field Tab Select Field F1 General Help F10 Save and Exit Esc Exit 3 2 MS 98A9 GETTING HELP After entering the Setup menu the first menu you will see is the Main Menu Main Menu The main menu lists the setup functions you can make changes to You can use the arrow keys 1 to select the item The on line description of the highlighted setup function is displayed at the bottom of the screen Sub Menu If you find a right pointer symbol S appears to the left of certain fields that means a sub menu can be launched from this field A sub menu contains additional options for a field parameter You can use arrow keys 7 to highlight the field and press lt Enter gt to call up th
34. tting enables disables the Security Device gt Intel TXT LT Configuration Aptio Setup Utility Copyright C 2012 gt PCH FW Configuration Aptio Setup Utility Copyright C 2012 MDES BIOS Status Code Disabled gt MDES BIOS Status Code This setting enables or disables MDES BIOS Status Code Firmware Update Configuration Configure Management Engine Technology parameters Aptio Setup Utility Copyright C 2012 Me FH Image Re Flash Disabled gt Me FW Image Re Flash Enable Disable ME FW Image ReFlash function Note Enable this option if BIOS update requires an update of the Intel Management Engine ME 3 15 BIOS Setup gt Intel R Anti Theft Technology Configuration Aptio Setup Utility Copyright C 2012 Intel R Anti Theft Technology Disabled gt Intel R Anti Theft Technology This item is used to enable disable the Intel Anti Theft Technology gt Intel R Anti Theft Technology Rec Set the number of times recovery attempted will be allowed gt Enter Intel R AT Suspend Mode This item is used to enable or disable the request that platform enters AT suspend mode AMT Configuration Aptio Setup Utility Copyright C 2012 Intel AMT Enabled gt Intel AMT This item is used to enable disable Intel Active Management Technol ogy BIOS Extension Note iAMT H W is always enabled This option just controls the BIOS extension execution If enabl
Download Pdf Manuals
Related Search