Using the CR1400 in a Universal Stand Using the CR1400 Out of a
Contents
1. Powering on the CR1400 For USB Cable plug the USB end of the Affinity cable into a USB port on the host device After several seconds the reader will beep twice and the LED will turn off to indicate the CR1400 is ready for use For RS232 Cable plug the power supply into the AC outlet plug the power supply cord into the barrel jack of the cable and connect the RS232 connector to the appropriate serial port on the host device After several seconds the reader will beep twice the reader will vibrate and the LED will turn off to indicate the CR1400 is ready for use Using the CR1400 Out of a Universal Stand Press and hold the CR1400 trigger the two blue bars emitting from the reader are used for targeting Center the blue bars in the middle of a bar code The optimal reading distance from reader to bar code is approximately 4 0 10 cm Once the reader is at the optimal distance the CR1400 will read the bar code when the trigger is pressed The CR1400 will beep vibrate and flash a green LED to indicate a good read has occurred Using the CR1400 in a Universal Stand Revision 2 Hardware of the CR1400 has a stand detection feature By default when the CR1400 is placed in the stand the reader will automatically enter into motion detection mode When in this mode simply place a bar code in the scan field to activate the reader The CR1400 will beep and flash a green LED to indicate a good read has occu2. of the Affinity cable into bottom of the reader Figure 1 Firmly push the connector into the reader until a snap can be heard to indicate the cable is properly attached To detach a cable press a paper clip into the hole on the back of the CR1400 Figure 2 and gently pull the cable from the reader Figure 1 Figure 2 Lae C006321_04_CR1000_Quickstart_Guide code
3. ration code M0141 02 pavers Suffix Enter USB Carriage Return Line Feed RS232 For more configuration options download the CR1400 Configuration Guide from www codecorp com Universal Stand Assembly included when ordered as a Kit Package Cleaning a CR1400 The following agents are approved to clean a Code bar code reader 1 Alcohol Wipes 2 CaviWipes Disinfecting Towelettes 3 Clorox Disinfecting Wipes 4 Clorox Bleach Solution 10 Clorox bleach 90 tap water 5 Medical DiAirKem 6 Sani Cloth HB Super Sani Cloth Germicidal Sani Cloth Plus Germicidal Disposable Wipes 7 Virex II Disinfectant Cleaner Warranty Code s CR1400 carries a five year standard warranty Universal Stands follow the warranty of the reader and cables have a 90 day warranty period For more warranty information please refer to the CR1400 User Manual available at www codecorp com code 14870 S Pony Express Rd 200 Bluffdale UT 84065 www codecorp com 801 495 2200 2012 Code Corporation All Rights Reserved 4 Quickstart Guide Code Reader 1400 CR1400 2 AN Included with your CR1400 Depending on the kit ordered the following may have been shipped with your reader RS232 Affinity Cable Universal Stand w Power Supply USB Affinity Cable Attaching Detaching a Cable To attach a cable plug the RJ 50 end
4. rred When the CR1400 is removed from the stand the reader switches to manual mode and the button must be pressed to read a bar code Revision 1 Hardware of the CR1400 does not have an automatic stand detection feature to enable motion detection reading when the CR1400 is in a stand To configure this hardware revision for motion detection scanning please refer to the CR1400 Configuration Guide located at www codecorp com files php and scan the appropriate code 2 Determining the hardware revision of your CR1400 Locate the Serial Label on the reader to identify the hardware revision CR1400 readers with a MFG of _02 or higher have the stand detection mode Serial 20000X XX MFG CR141 _02 indicates Designed in USA Made in Malaysia revision 2 hardware CR1400 Default Settings The CR1400 out of the box will read the following bar codes Aztec Code 39 Short Margin All GS1 DataBar QR Code Codabar Code 93 Interleaved 2 of 5 Telepen Codablock F Code 128 MSI Plessy UPC Code 11 Code 128 Short Margin NEC 2 of 5 UPC Short Margin Code 39 Data Matrix PDF417 To configure a CR1400 to read bar codes not listed please download the CR1400 Configuration Guide from www codecorp com and scan the appropriate Enable bar code reading symbology configuration code Suffix Enter Configuration The default setting on the CR1400 has Suffix Enter disabled To enable Suffix Enter please scan the following configu
Download Pdf Manuals
Related Search