ERO Laser Movinghead with fat beam laser diode User manual
Contents
1. ERO Laser Movinghead with fat beam laser diode k k i AN 4 rr t Y 7 i aP As i A j A Tra k P p ra aig Perec cae a User manual Safety precautions WARNING This unit may cause serious injury to eyesight when used incorrect It therefore is strongly advised to read this user manual carefully to get familiar with the functions of this laser device WARNING This unit must be operated by or under the supervision of an adult This device is not suitable for children WARNING Do not look directly into the beam coming out of the lens from short distance or when a solid beam is projected This may cause serious injury to eyesight Ayra is not responsible for any injuries caused by incorrect use of this device WARNING Do not project the beam of this unit on to reflective surfaces as the shattering beam may cause injury to eyesight Installation requirements Always check the voltage settings on the unit and the power supply you want to connect the device to If the voltage requirements do not meet do not connect the device as this may cause serious damage This device must be installed by a professional technician in a standing or hanging position Always pay attention to the positioning of the unit as the beams may project directly into your audience Itis strongly advised to NOT project the beams directly into your audience Ayra strongly recommends a minimum distance of 1 5 meters in heig2. is projected into your audience however Ayra does not recommend this kind of use The used laser diode is an 80 mW green fat beam diode The diameter of the projected beam is 10mm The fixture can be placed on a solid surface with the rubber feet When using the fixture in a hanging position the included mounting bracket must be used and the safety eye must be mounted The fixture must be installed by mounting a proper bolt or hook to the bracket Use a safety cable on the safety eye to make sure the fixture can not fall down This prevents possible damage and severe injury The safety cable must be capable of holding at least 10x the weight of the fixture The fixture must be positioned in such a way that the distance in height is at least 1 5m from the audience This prevents solid beam projections in the audience for longer periods of time Projection into your audience is not recommended but will not cause any harm when the installation requirements are met The ERO Laser fixture can be mounted in almost every position including horizontal or upside down Use proper installation hardware such as half couplers for truss systems DMX operating mode While in the DMX mode it is possible to select the working mode of the laser That way you can either choose to use your own programmed presets of your DMX controller or to activate the music activated automatic working mode of the laser to have a fully automatic lasershow Depending on the
3. slow mode or fast mode Slave mode It is possible to link several ERO laser fixtures for a synchronized lasershow without the use of a DMX controller Connect your devices with standard XLR XLR cables The first device in the chain needs to be set to a basic function such as sound active or one of the auto shows Select the slave mode on all other connected device in the chain You will notice that these devices will mimic the actions of the first device It is possible to invert the pan or tilt function on slave fixtures for synchronized shows DMX mode With an external DMxX controller or DMX software it is possible to control every feature of the laser device It is possible to adjust the built in patterns and to add several effects such as zoom effects or pattern rotation NOTE When the DMx signal or master slave signal is lost due to a failure in the DMX connection or any other reason the laser will shut off the output due to safety issues This prevents the projection of static images and or patterns Placement and mounting of the fixture For safety reasons the ITA ERO Laser is equipped with a laser diode of the type fat beam This means the diameter of the laser beam is much thicker than a regular laser beam to spread the intensity of the laser beam on a larger surface Therefore the intensity of the laser beam is lower than a regular laser projecting a static dot on a surface This prevents injury when the beam
4. working modes which are automatic music controlled and DMX To select the right operating mode for your situation use the dipswitch panel on the rear of the unit The display of the unit shows certain statuses which are used to set preferences A short explanation of the codes and values are shown below NAFR Main menu NASL SLOV Master slow auto mode SLAV SON Slave mode NSEC CRLN single laser slow auto mode NSES SRLN master sound activation NAFA FASE Master fast auto mode PAN Pan pan movement normal RPan pan movement inverted Fl FI tilt movement normal RFI tilt movement inverted DIS DIS normal display mode RDIS display mode inverted REST Reset mode LOFN Reset to factory settings Working mode explanation Sound active The unit uses its internal microphone to sense music the beat of the music and will change rotation color and speed according to the beat of the music The microphone is situated at the front of the laser device On the rear of the laser there is an adjustable microphone sensitivity knob Please note that the sound activated mode will not function properly when the music source is not loud enough or when only high pitched sounds are played The laser device will shut off when there is no music detected due to safety issues Auto The laser device will activate a pre defined lasershow on a solid speed setting The patterns change ona pre defined speed It is possible to select a
5. ays disconnect the unit from the power supply when cleaning the unit Reconnect the unit only if any moist on the fixture disappeared completely This laser device is a lighting effect designed to support visual entertainment while playing music Continuous use is not recommended Do not use the device longer than 3 hours subsequently so the unit can cool down This will provide a longer lifespan for the diodes Apply a cooling down time of 25 minutes before re activating the laser Do not switch the power on and off too often as this may cause serious damage to the unit Avoid heavy shocks and collision during transport and use as this might cause damage to the laser diodes electronic circuit optics and housing Keep the device away from moisture rain water or any liquids as this may cause a short circuit and or electric shocks If any liquid enters the unit power supply or housing of the unit disconnect the unit immediately and do not reconnect the power supply Contact your local dealer or technician to inspect the unit for any damage Box contents Box contents 1x ERO Laser movinghead 1x user manual 1x IEC to Schuko power cable 1x mounting bracket with hardware 1x safety eye Unit and accessory inspection Always use the supplied power cable to connect the unit to a power supply If the cable appears broken or has visible damage do not use it The supplied cable can be replaced with a regular IEC to Schuko cable wit
6. h a minimum cable diameter of 0 75m7 If the unit will not be used for a longer period of time disconnect it from the power supply and store it in a dust free environment Always check the unit for possible damage before use If you suspect that something is wrong with the unit do not connect it to a power source When you suspect that your unit is broken or damaged contact your local dealer or a certified technician to inspect the unit When your device does not generate any laser beams do not look directly into the lens When the laser suddenly produces a beam it may cause severe eye damage possibly resulting in permanent visual loss Device overview Laser beam output Menu display with navigation buttons Cooling fan head IEC input with fuse DMX input DMX output Mounting bracket illustrated mounted on the bottom Cooling fan base 1 2 3 4 5 6 T 8 Setting up the device Setting up the device When the power supply is connected the unit will first calibrate the stepping motors of the unit It is normal that this may cause any noise When the calibration is done the unit is ready to be used in the selected DMX automatic or music controlled mode Itis possible that the unit may shut off the beam projection when no music or sound is detected This will avoid the projection of a solid static beam which may cause injury to eyesight Selecting a working mode This laser device has three
7. ht between the lowest projected laser beam and your audience for optimal safety If there is no other option keep a minimum distance of 5 meters from the beam exit to the first beam that hits your audience When installed in a standing position a safety cable is recommended to secure the unit When installed in a hanging position this unit MUST be secured by using a safety cable capable of holding 10x the weight of this device When installed in a hanging position this unit must be mounted to a proper surface e g a truss system When using a truss system Ayra recommends the use of a proper hook or halfcoupler Make sure there are no flammable objects in the direct environment of the device such as decorative objects Keep a minimum distance of 1 5 meter Do not block the beam exit and fan Keep a minimum distance of 0 5 meter from any walls to provide sufficient cooling Make sure the beam exit and fan are not blocked by any objects in the near environment This unit must be connected to a grounded power supply that meets the voltage requirements of the device Maintenance and protection Keep the unit away from dusty environments as this may have negative effect on the fan cooling system and laser optics Ayra recommends using a flightcase for storage of this device Clean the optics and fan of the laser with a small soft brush and vacuum cleaner when needed Clean the housing of the unit with a damp cloth WARNING Alw
8. starting address you selected earlier the laser responds to the following commands In this example we use DMX starting address 1 When you use a different DMX starting value for example 29 the unit will respond from channel 29 30 31 and so on For more information about DMX consult the manual of your DMX controller or software 0 255 X Y axis movement speed 8 134 Shutter open CH6 239 255 Shutter open Technical specifications TYPE ERO Laser Laser diode 80 mW green fat beam laser diode 10 mm 532 nm Tech specs Laser movinghead with 80mW green fat beam laser diode light source Projects static fat beam laser beams Strobe function 540 degrees pan movement 180 degrees tilt movement high quality optical system for bright beams fan cooled TTL laser modulation working temperature 10 35 degrees Celsius working modes auto sound controlled DMX DMxX channels 6 voltage requirements 110 230V AC 50 60 Hz power consumption 200W size 185 x 175 x 290 mm weight 3 5 kg
Download Pdf Manuals
Related Search