inno racks rt201 rt202 velo gripper truck bike rack installation
Contents
1. CARMATE 5420 103618 wit RT201 202 Velo Gripper Instruction Manual Thank you for purchasing this INNO product Please read through this manual thoroughly before use and make sure that you follow all of the instructions carefully After reading this instruction manual store it in a safe place for future reference If you have any questions regarding this product please contact the service center shown at the bottom of the page z Parts or loaded items falling from the rack can cause There is risk of injury or damage to the rack A Warning serious accidents involving passers by or other cars A Caution vehicle or loaded items which may lead to serious injury or death Before using this product check the vehicle compatibility table to make sure it is compatible with your vehicle Before using this product check the type of objects that can be loaded and maximum load weights according to the type of vehicle Before driving make sure that the knob is not loose Do not attempt to modify the carrier system Do not use crossbars and loading items that exceed the width of the vehicle This product is not for off road use Always drive safely Do not use automatic car washes Load evenly Remove the bed liner when it interrupts the installation of the carrier Maximum load of this carrier is 1 bike or 33 Ibs 15kg Product Contents Main unit 2 2 Bike rod 2 3 Plate 2 4 Hex wrench 1 B2. the body of the truck it may be necessary to adjust bike position repeat steps 4 through 7 to secure or cover crank and or pedal with a protective covering as not to cause vehicle damage US 2 8 After determining that the clamps over the rail of the truck bed tighten the eye bolt while pushing the clamp against the side wall of the truck bed And make sure eye bolts are firmly tightened A Warning Before driving check front and rear clamps and bars for looseness and the eye bolt 2 locations for looseness if any of them are loose re tighten them Pushing A Caution Note Please make sure you follow instruction in the attachment instruction manual correctly To lock Velo Gripper Load evenly Do not install the bike rods with the end sticking out from the side of vehicle To lock bike and clamps With a tapered end cable thread m through eye bolts and bike A 5 to 6 long and smaller than T use tie down 0 75 inch diameter cable is normally Maxi aaa sufficient to lock two clamps and bike aximum force of this D ring is F 66 Ibs 30kgf 7 Wash off dirt and mud with water Part inspection i Clean the product and inspect each of Wipe off dirt with a damp wet the parts for abnormalities If you towel discover any deformed or damaged f a Ne parts discontinue use immediately and Allow it to dry in the shade replace the pa
3. S NANA 6 Instruction manual F this manual 1 For standard For C channel Installation Procedure 1 Clean the side rails of the truck bed where product is to be installed 2 Place the plate on the mounting position US 1 For standard truck RT201 For C channel truck RT202 3 Loosen the eye bolt 1 2 way to allow the clamp to 3 Loosen the eye bolt 1 2 way to allow the square slip over the truck bed rail and centered on plate plate to slide into the C channel rail When the square plate doesn t slide due to interior mounting bolt inside the C channel the square plate needs to be removed from the eye bolt Pushing Outside Truck body Square plate C channel Eye bolt 4 Untighten the hex bolts and remove the cap Place the bike rod and reattach the cap and the hex bolts Outside but don t tighten until determining how much of the bike rod needs to be protrude from clamp yas Bike rod Buckle Place bike standing up in the truck bed and strap down both front fork and seat stay by inserting straps around forks and then through buckles pulling tightly Inside of truck bed Outside of truck bed Adjust the position of the bike rod by moving in or out to line up with the bike frame crank arm and or fork When position of the bike is most vertical tighten hex bolts firmly by the provided wrench located on cap If the cranks and or pedal hit
4. rts Storage 4 Caution Store in a dry place indoors out of Do not use solvents such as thinner etc direct sunlight Do not lubricate screws or bolts Contact Information If you have any complaints requests or comments please contact us at the service center listed below Car Mate USA shall not be held liable for any accidents or incidental losses arising from improper installation or use nor for those arising from installation or use after the customer has made any modifications to the system s original configuration or specifications u Car Mate USA 383 Van Ness Ave Suite 1603 Torrance CA 310 533 9881 q ADVANCED CAR RACKS www innoracks com support innoracks com US 3
Download Pdf Manuals
Related Search