Reiker Room Conditioner Ceiling Fan Heater User Manual
Contents
1. different ways to mount the outlet box Phillips screw driver straight slot screw driver adjustable wrench step ladder and Wire cutters Mounting Options If there isn t an existing mounting box then read the following instructions Disconnect the power by removing fuses or turning off the circuit ULListed breaker Fan Outlet Box Secure the UL listed fan outlet box directly to the building structure Use appropriate fasteners and building materials The outlet box and its support Figure 1 must be able to fully support the moving weight of the room conditioner at least 35 Ibs DO NOT USE PLASTIC OUTLET BOXES WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR OTHER PERSONAL INJURY MOUNT ROOM CONDITIONER ONLY TO AN OUTLET BOX MARKED ACCEPTABLE FOR CEILING FAN SUPPORT AND USE THE MOUNTING SCREWS PROVIDED WITH THE UL Listed Fan Outlet Box OUTLET BOX OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF LIGHTING FIXTURES MAY NOT BE ACCEPTABLE FOR ROOM CONDITIONER SUPPORT AND MAY NEED TO BE REPLACED CONSULT A QUALIFIED ELECTRICIAN IF IN DOUBT Figure 2 4 Installing Your Room Conditioner Provide Strong Support Recessed UL Listed Ceiling Fan Outlet gt Mounting Box Plate Figure 3 Note You may need a longer down rod to maintain proper blade clearance when installing on a steep sloped ceiling The maximum angle available is 30 degrees If the canopy touches the down rod2. 8 9 10 11 12 13 Avoid placing objects in the path of the blades To avoid personal injury or damage to the room conditioner and other items be cautious when working around or cleaning the room conditioner Do not use water or detergents when cleaning the room conditioner or room conditioner blades A dry dust cloth or lightly dampened cloth will be suitable for cleaning After making electrical connections spliced conductors should be turned upward and pushed carefully up into outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box Electrical diagrams are for reference only Optional light kits are expressly prohibited for use on the Reiker Room Conditioner Do not stick objects into or through the protective screens that are in front of the heating elements CAUTION Ensure adequate circuit protection available Safety Rules IMPORTANT INSTRUCTIONS cont 14 15 16 17 18 19 20 21 22 23 Read all instructions before using this Room Conditioner Do not use outdoors To disconnect Room Conditioner turn controls to off switch off at circuit breaker then remove Room Conditioner from mounting location Make sure to properly ground installation Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage the
3. remove the decorative canopy bottom cover and turn the canopy 180 degree before attaching the canopy to the mounting plate ne Mount only to a UL Listed Figure 4 Fan Brace and Box To hang your room conditioner where there is an existing fixture but no ceiling joist you may need an installation hanger bar as shown in Figure 4 Hanging the Room Conditioner REMEMBER to turn off the power Follow the steps below to hang your Room Conditioner properly NOTE This room conditioner is supplied with two types of hanging assemblies the standard installation using the downrod with ball and socket mounting and the close to ceiling mounting The close to ceiling mounting is recommended in rooms with less than 8 foot ceilings or in areas where additional space is desired from the floor to the room conditioner blades When using a standard downrod installation the distance from the ceiling to the bottom of the room conditioner blades will be approximately twelve inches An extra six inch downrod is included that will increase this distance to fifteen inches Please see page seven for steps for changing the downrod The close to ceiling installation reduces the distance from the ceiling to the bottom of the room conditioner blades to approximately 9 inches Once you have decided which ceiling installation you will use proceed with the following instructions Where necessary each section of the i
4. 6 Re tighten the set screw at the top of the Room Conditioner motor by first loosening the nut towards the screw head tightening the set screw firmly and tightening the nut against the mounting collar Figure 8 7 Proceed to Installing the Room Conditioner section Loosen Nut gt 2 Tighten lt Set Screw Tighten Nut Figure 8 CLOSE TO THE CEILING MOUNTING 1 Remove the canopy ring from the canopy by turning the ring to the right until it unlocks 2 Remove the mounting plate from the canopy by loosening the four screws on the top of the canopy Remove the two 6 99 6 non slotted screws and loosen the slotted screws This will enable you to remove the mounting plate Remove the decorative canopy bottom cover from the canopy by depressing the three studs Canopy E Bottom Figure 9 Cover Remove three of the six screws and lock washers securing the motor collar to the top of the Room Conditioner motor housing Place the rubber gasket over the remaining three screws route the wires exiting the top of the Room Conditioner motor through the canopy ring make sure the slot openings are on top then proceed to place the ceiling canopy over the collar at the top of the motor Figure 11 Align the mounting holes with the holes in the motor and fasten using the three screws whith lock washers provided in the close to ceiling mount
5. Room Conditioner To prevent a possible fire do not block air intakes or exhaust in any manner Room Conditioner has hot and arcing or sparking parts inside Do not use it in areas where gasoline paint or flammable liquids are used or stored Use this Room Conditioner only as described in this manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons Installation is to be in accordance with the National Electrical Code ANSI NFPA 70 and local codes Keep combustible material such as curtain at least 3 feet from the hater outlets ROEM CONDITIONER American Technology saving the World s heating problems 11 Unpack your Room Conditioner and check the contents You should have the following items 1 Slide on mount plate inside canopy 6 Light Kit A Blade attachment hardware 2 Ball Downrod Assembly 1 7 Blades B Mounting Hardware Locking Pin amp 3 Canopy with Canopy ring attached 8 6 Downrod Hanger Pin 4 Motor Collar cover 9 Remote Control Hand Unit C Close to ceiling mounting hardware 5 Room Conditioner and pre attached 10 Hand Unit Wall Mount 1 Rubber Gasket 3 Screws Blade brackets 11 Balancing kit D Wire Nuts 3 12 2 Compact Fluorescent Bulbs This product is patent pending in the United States and foreign countries Unpacking Your Room Conditioner 3 Tools Required Figures 1 2 and 3 are examples of
6. hardware package Tighten the mounting screws securely crew and Lockwasher 3 of 6 places Figure 11 Gasket WARNING FAILURE TO COMPLETELY TIGHTEN THE THREE SCREWS IN STEP 7 MAY RESULT IN ROOM CONDITIONER LOOSENING AND FALLING WARNING WHEN USING THE STANDARD BALL HANGER PIPE MOUNTING THE TAB IN THE RING AT THE BOTTOM OF THE MOUNTING PLATE MUST REST IN THE GROOVE OF THE HANGER BALL FAILURE TO PROPERLY SEAL THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING Changing the Downrod Optional Please see following steps on changing the downrod prior to installation 1 Remove hanger ball from 4 downrod by loosening the set screw at the top of the downrod which holds the hanger ball to the downrod This is not the screw with the green ground wire attached 2 Slide the hanger ball down the downrod and remove the support pin 3 Insert the support pin in the holes at the top of the 6 downrod and slide the hanger ball up the 6 downrod Make sure the support pin is properly seated in the grooves in the top of the hanger ball 4 Tighten the set screw 5 Return to page 5 to continue the installation Installing Room Conditioner to the Electrical Box CAUTION WHEN MOUNTING THE ROOM CONDITIONER ON A SLOPED CEILING THE STANDARD BALL DOWNROD MOUNTING METHOD MUST BE USED THE MOUNTING PLATE MUST BE MOUNTED SO THAT THE SLOT OPENINGS ARE ON THE LOWER SIDE BY SLIDING THE MOUNTING PLATE FROM THE
7. the screws in the canopy Rotate the ring clockwise to lock in place 4 You may proceed to attaching the Room Conditioner blades CLOSE TO CEILING MOUNTING 1 Carefully unhook the Room Conditioner from the mounting plate and align the locking slots of the ceiling canopy with the two screws in the mounting plate Push up to engage the slots and turn clockwise to lock in place Immediately tighten the two mounting screws firmly WARNING LOCKING SLOTS OF CEILING CANOPY ARE PROVIDED ONLY AS AN AID TO MOUNTING DO NOT LEAVE ROOM CONDITIONER ASSEMBLY UNATTENDED UNTIL ALL FOUR CANOPY SCREWS ARE ENGAGED AND FIRMLY TIGHTENED 2 Install the remaining two mounting screws into the holes in the canopy and tighten firmly 3 Install the decorative canopy ring by aligning the ring s slots with the screws in the canopy Rotate the ring clockwise to lock in place 4 You may now proceed to attaching the Room Conditioner blades Attaching the Fan Blades 1 Attach the blades to the Room Conditioner motor housing by inserting the blade into the slot in the side of the fan motor housing and secure using the screws and the fiber washers provided Start a screw into the bracket Repeat for the two remaining screws 2 Tighten each screw securely Attaching Fan Blades to Fan Motor Housing Be es Screw with Fiber Washer Figure 15 3 Repeat steps 1 2 amp 3 for the remaining blades The fol
8. with the picture of the light bulb on it This will illuminate the Reiker Room Conditioner WARNING REMOVING THE REMOTE CONTROL OR ALLOWING THE BATTERIES TO FAIL FROM THE ROOM WILL CAUSE THE UNIT TO MALFUNCTION AND FAIL TO OPERATE IN THE PRESCRIBED MANNER The Simplest Remote Desired Room Temperature Degree Low Battery Indicator Fan Speed Indicator In Fan Mode DESIRED ROOM TEMPERATURE Heat Output Indicator In Heat Mode Operation Mode Indicators Heat Fan ACTUAL ROOM TEMPERATURE Power Button Actual Room Temperature On Off Degree Increase Heat Button Increase Fan Speed Button Plus Plus Heat Button Fan Button On Off On Off Decrease Heat Button Decrease Fan Speed Button Minus Minus Light Button On Off NOTE Fan speed can NOT be adjusted during heating mode RECOMMENDATION KEEP THE REMOTE IN THE HOLDER RECOMMENDATION REPLACE THE BATTERIES AT LEAST EVERY THREE MONTHS IN THE ROOM BEING USED Here are some suggestions to help you maintain your Reiker Room Conditioner 1 Because of the Room Conditioner s natural movement some connections may become loose Check the support connections brackets and blade attachments twice a year Make sure they are secure It is not necessary to remove the Room Conditioner from the ceiling 2 Clean your Room Conditioner periodically to help maintain its new
9. ILE ATTACHING WIRING FAILURE TO HANG AS SHOWN IN FIG 13 MAY RESULT IN HOOK BREAKING CAUSING THE ROOM CONDITIONER TO FALL HOOK MUST PASS FROM INSIDE TO OUTSIDE OF CANOPY Making the Electrical Connections REMEMBER to disconnect the power If you feel that you do not have enough electrical wiring knowledge or experience have your Room Conditioner installed by a licensed electrician Follow the steps below to connect your Room Conditioner to your household wiring Use the wire connecting nuts supplied with the Room Conditioner Secure the connectors with electrical tape Make sure there are no loose strands or connections Step 1 Connect the Room Conditioner supply black wire to the black household supplied wire with wire nuts as shown in Figure 14 Step 2 Connect the neutral Room Conditioner white wire to the white neutral household wire with supplied wire nuts Step 3 Connect the two green Room Conditioner ground wires located on the 8 downrod and mounting bracket to the household ground wire with the supplied wire nuts When using close to ceiling mounting there is only one green ground wire from the ceiling mounting bracket since the ball downrod assembly is not there Step 4 After connecting the wires spread them apart so that the green and white wires are on one side of the outlet box and the black wires are on the other side Step 5 Turn the wire connecting nuts upward and push the w
10. L MOUNT Operating Your Room Conditioner 11 How to use the Remote Control As the desired temperature the numbers CAUTION THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID YOUR AUTHORITY TO OPERATE THE EQUIPMENT 1 Heating with the Reiker Room Conditioner In order to initiate the heat mode press the power button to turn the Reiker Room Conditioner on The remote control will light up to show power has been initiated If the remote control does not illuminate check to see if the batteries are still good Press the heat button to put the room conditioner in the heat mode The word heat should illuminate when in the heat mode Next set the temperature to your desired comfort level with the plus or minus buttons located above or below the heat button When the unit turns on all four heating elements will activate This is indicated by the four bars that will light up above the actual room temperature at the top of the controller will change in correspondence with the plus or minus buttons The Reiker Room Conditioner will now begin heating your room As the actual room temperature increases and nears that of the desired room temperature the unit will automatically decrease the number of heating elements in order to maintain the desired temperature for the least amount of electricity to maintain your desired temper
11. Reiker Room Conditioner Lifetime Limited Warranty The retailer warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a lifetime after the date of purchase by the original purchaser The retailer also warrants that all other fan parts excluding any glass or Plexiglas blades to be free from defects in workmanship and material at the time of shipment from the factory for a period of one year after the date of purchase by the original purchaser We agree to correct such defects without charge or at our option replace with a comparable or superior model if the product is returned to the retailer To obtain warranty service you must present a copy of the receipt as proof of purchase All costs of removing and reinstalling the product are your responsibility Damage to any part such as by accident or misuse or improper installation or by affixing any accessories Is not covered by the warranty Because of varying climatic conditions in the United States this warranty does not cover any changes in brass finish including but not limited to rusting pitting corroding tarnishing or peeling Brass finishes of this type give their longest useful life when protected from varying weather conditions A certain amount of wobble is normal and should not be considered as a defect Servicing preformed by unauthorized persons will render the warranty invalid There is no other expressed warranty The re
12. TOP DOWN 1 Pass the 120 Volt supply wires through the center hole in the ceiling mounting plates shown in Figure 12 2 Remove the mounting screws from the outlet box install the flat washers supplied in the hardware bag to the mounting screws then install the ceiling mounting plate on the electrical box by using 2 mounting screws with flat washers attached When using close to ceiling mounting it is important that the mounting plate be level If necessary use leveling washers not included between the mounting plate and the electrical box Note that the flat side of the mounting plate is to be toward the electrical box 3 Securely tighten the 2 mounting screws 4 Carefully lift the Room Conditioner assembly up to the ceiling mounting plate If using close to ceiling mounting hang the Room Conditioner on the hook provided by utilizing one of the holes at the outer rim of the ceiling canopy fusing standard mounting seat the hanger ball in the mounting plate socket Make sure the tab on the mounting socket is properly seated in the groove in the hanging ball ULL Listed Metal Electrical Box Leveling Isolation pads Grounding Wire Ceiling Ceiling Mounting Plate Mounting Screws with Flat Washers 120 Volt Supply Wires Figure 12 Close to Ceiling Mounting Standard Mounting Figure 13 WARNING THE HOOK AS SHOWN IN FIG 13 IS ONLY TO BALANCE ROOM CONDITIONER WH
13. appearance over the years Do not use water when cleaning Use only a soft brush or lint free cloth to avoid scratching the finish The plating is sealed with a lacquer to minimize discoloration or tarnishing Cleaning could damage the motor the wood or possibly cause an electrical shock 3 You can apply a light coat of furniture polish to the wood for additional protection and to enhance beauty Cover small scratches with a light application of shoe polish 4 There is no need to oil your fan The motor has permanently lubricated sealed ball bearings WARNING MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU ATTEMPT ANY REPAIRS REFER TO THE SECTION MAKING ELECTRICAL CONNECTIONS Changing the Dust Cover Located on top of the Reiker Room Conditioner is a dust cover This dust cover is used to prevent dust from getting into the heating chamber 1 Squeeze the dust cover together until it is loose from the raised edges of the top of the Room Conditioner and then pull it off 14 Care of Your Room Conditioner 2 Rinse it out with water and allow to thoroughly dry Squeeze the ends towards each other and place it under the openings around the support rod WARNING MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU ATTEMPT TO CLEAN THE DUST COVER ROOM CONDITIONER American Technology saving the World s heating problems Problem Fan will not start Fan sounds
14. ature As the actual temperature meets the desired temperature the heating elements will start to cut off and the unit will run for the least amount of electricity Should the temperature in the room decrease the unit will automatically add additional heat until the desired temperature is reached again 2 Cooling with your Reiker Room Conditioner During the summer months the Reiker room Conditioner can be used as a ceiling fan In order to activate the Reiker Room Conditioner in the Ceiling fan mode you must first press the power button The remote control will light up to show power has been initiated If the 12 How to use the Remote Control remote control does not illuminate check to see if the batteries are still good Next press the fan button to initiate the ceiling fan mode In order to regulate the speed of the fan you must select either the plus or the minus button to set the fan at high medium or low This is represented by the lighted bars above the actual room temperature If one is lit it is at low speed if two are lit it is at medium speed and if they are all lit then it is at high speed 3 How to use the light kit In order to turn the light kit on you must first turn on the Reiker Room Conditioner by pressing the power button The remote control will light up to show power has been initiated If the remote control does not illuminate check to see if the batteries are still good Next press the button
15. ber isolator pads were used between the mounting plate and ceiling box Troubleshooting 15 Saving your energy every minute of everyday Heat Mode Heating Elements SPEED VOLTS AMPS WATTS RPM NET WEIGHT GROSS WEIGHTICUBIC FEET 1 Med 120 4 1 496 2 Med 120 7 5 892 3 Med 120 10 05 1173 40 5 Ibs 4 Med 120 12 5 1485 Ceiling Fan Mode Fan Size SPEED VOLTS AMPS WATTS RPM NET WEIGHT GROSS WEIGHT CUBIC FEET Low 120 0 51 45 65 54 Med 120 0 67 68 105 40 5 lbs High 120 0 8 99 170 NOTE The Reiker Room Conditioner was designed to efficiently heat a room as large as 20 by 20 with a 10 ft ceiling If you have a room larger than this you may need an additional unit If the room is smaller than this the unit will function better These are approximate measurements they include Amps and wattage used by the light kit Thank you for purchasing the Reiker Room Conditioner We know that you will enjoy many years of satisfaction and savings with your new energy efficient Reiker Room Conditioner that you will want to run out and tell your neighbors about it Thanks again for your purchase of the Reiker Room Conditioner 2003 Reiker Room Conditioners LLC For logos product I D and names All Rights Reserved 16 Specifications
16. ditlonet Page 14 Troubleshootih t nsari Page 15 Page 16 American Technology saving the World s heating problems CONDITIONER Table of Contents READ AND SAVE THESE INSTRUCTIONS To reduce the risk of electrical shock insure electricity has been shut off at the circuit breaker or fuse box before beginning All wiring must be in accordance with the National Electrical Code and local electrical codes Electrical installation should be preformed by a qualified licensed electrician WARNING To reduce the risk of electrical shock and fire do not use this room conditioner with any solid state speed control device CAUTION To reduce risk of personal injury use only the screws available with the outlet box The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 pounds Use only UL listed outlet boxes marked FOR CEILING FAN SUPPORT Remote Control Transmitter batteries should be changed every three months or when transmitter low battery indicator illuminates WARNING To reduce the risk of fire electrical shock or personal injury Mount to outlet box marked acceptable for ceiling fan support and use screws provided with the outlet box 7 The room conditioner must be mounted with a minimum of 7 feet clearance from the trailing edge of the blades to the floor
17. iring into the outlet box WARNING TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK DO NOT USE A WALL MOUNTED SOLID STATE SPEED CONTROL WITH THIS ROOM CONDITIONER IT WILL PERMANENTLY DAMAGE THE ELECTRONIC CIRCUITRY WARNING EACH WIRE NUT WIRE CONNECTOR SUPPLIED WITH THIS ROOM CONDITIONER IS DESIGNED TO ACCEPT UP TO ONE 12 GAUGE HOUSE WIRE AND TWO WIRES FROM THE ROOM CONDITIONER IF YOU HAVE LARGER THAN 12 GAUGE HOUSE WIRING OR MORE THAN ONE HOUSE WIRE TO CONNECT TO THE ROOM CONDITIONER WIRE ONSULT AN ELECTRICIAN FOR THE PROPER SIZE WIRE NUTS TO USE SUPPLY CIRCUIT at Binok White ay i Mater Connector Light Ciner Brewit Ciageem indicates lige wiring Finishing the Room Conditioner Installation STANDARD CEILING ROOM CONDITIONER Warning WHEN USING THE STANDARD BALL DOWNROD MOUNTING THE TAB IN THE RING AT THE BOTTOM OF THE MOUNTING PLATE MUST REST IN THE GROOVE OF THE HANGER BALL FAILURE TO PROPERLY SEAT THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING 1 Align the locking slots of the ceiling canopy with the two screws in the mounting plate Push up to engage the slots and turn clockwise to lock in place Immediately tighten the two mounting screws firmly 2 Install the remaining mounting screws into the holes in the canopy and tighten firmly 3 Install the decorative canopy ring by aligning the ring s slots with
18. lowing procedure should correct most fan wobble Check after each step 1 Check that all blade screws are secure 2 Use the enclosed Blade Balancing Kit if the blade wobble is still noticeable WARNING TO REDUCE THE RISK OF PERSONAL INJURY DO NOT BEND THE BLADE HOLDERS WHILE INSTALLING BALANCING THE BLADES OR CLEANING THE FAN DO NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES 10 Installing the Light Kit REMEMBER to disconnect the power 1 Loosen two opposing mounting screws on the black bracket below the motor and remove the other two opposing screws 2 Connect the blue wire exiting the bottom of the Room Conditioner motor assembly with the black wire from the top of the light kit fitter assembly Connect the white wire exiting the bottom of the fan motor assembly with the white wire from the top of the light kit fitter assembly See page 8 for wiring diagram 3 Attach the light kit assembly to the fan motor assembly by securing with the four screws loosened in step 1 Push light kit assembly up to engage screw heads in slots and turn to secure Tighten each screw firmly 4 With the power off Screw in the two fluorescent light bulbs into the sockets When replacing the light bulbs only use fluorescent bulbs WARNING DO NOT USE BULBS ABOVE 15 WATTS A PIECE FAILURE TO DO SO COULD RESULT IN A FAILING CIRCUIT BREAKER 5 Attach the decorative globe by sliding it up the threaded
19. noisy Solutions Ne Check main and branch circuit fuses or breakers Make sure that you do not have more than 30 watts worth of light bulbs in the unit Each light bulb should not exceed 15 watts Recommended bulb is a 14 watt Compact fluorescent Should the circuit breaker trip after resetting consult your electrician about adequate circuit protec tion Check line wire connection to the fan CAUTION Make sure main power is off Check batteries in the transmitter Does the liquid crystal display LCD illuminate and is the battery low light off Are you standing close enough to the fan normal range is 20 feet Are the dip switch settings in the transmitter properly configured REFER TO PAGE 11 FOR SETTING THE DIP SWITCH Batteries should be changed every three months or as needed Make sure the Room Conditioner power supply wires have not been pushed into the inside of the Room Conditioner This will create a scratching sound due to the wires rubbing against the impeller motor Make sure all motor housing screws are snug Allow a 24 hour breaking in period Most noises associated with a new fan disappear during this time If using the Room Conditioner light kit make sure the finial securing the decorative globe is tight Check that the light bulbs are also secure Make sure the canopy is a short distance from the ceiling It should not touch the ceiling Make sure your ceiling box is secure and rub
20. nstructions will note the different procedures to follow for the two types of installation STANDARD CEILING MOUNTING 1 Remove the canopy ring from the canopy by turning the ring to the right until it unlocks Figure 5 tum Amara 2 Remove mounting plate from canopy by loosening the four screws on the top of the canopy Remove the two non slotted screws This will enable you to remove the mounting plate Figure 6 3 Route the wires exiting the top of the room conditioner through the canopy ring Make sure the slot openings are on top Route the wires through the canopy and then through the ball downrod assembly and collar cover Figure 7 4 Loosen but do not remove the set screw on the collar on the top of the motor housing Bali aroge Fipa Cones fing Chee cra Airie Colm Figure 7 Align the holes at the bottom of the down rod with holes on the collar on top of the motor housing Carefully insert the hanger pin through the holes in the collar and the down rod Insert the locking pin through the hole near the end of the hanger pin until it snaps into its locked position WARNING DO NOT SHOVE EXCESS WIRE INTO ROOM CONDITIONER THIS WILL CAUSE WIRE TO GET CAUGHT OR SCRAPE IMPELLER MOTOR WARNING FAILURE TO PROPERLY INSTALL LOCKING PIN AS IN STEP FIVE COULD RESULT IN ROOM CONDITIONER LOOSENING AND POSSIBLY FALLING
21. rod and securing it with the steel nipple Attach nut ta O threaded rod WARNING DO NOT OVER TIGHTEN WHEN INSTALLING THE GLASS SHADE INTO THE LIGHT KIT ASSEMBLY ALLOW THE GLASS SHADE TO COOL COMPLETELY BEFORE REMOVING Cool Weather Operation 1 Press the Room Conditioner remote control thermostat power button 2 Use the remote control thermostat and press the heat button 3 Once your Room Conditioner is in the heat mode adjust the thermostat to the desired temperature you would like to maintain in the room 4 Your Reiker Room Conditioner will soon bring the room to your desired temperature Once the desired temperature is obtained the heating elements will automatically cut off until the most efficient combination of energy consumption to comfort level is accomplished Enjoy your new cost effective Reiker Room Conditioner Warm Weather Operation As the warmer season draws near and the need for heating your house is decreased the Reiker Room Conditioner can also be used in a cooling mode much like conventional ceiling fans 1 Make sure the blades are not moving then select the fan mode 2 There are three speed selections in the cooling mode Low Medium and High CAUTION THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID YOUR AUTHORITY TO OPERATE THE EQUIPMENT Lighting Located on the hand held remote con
22. tailer hereby disclaims any and all warranties including but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by law The duration of any implied warranty which cannot be disclaimed is limited to the time period as specified in the express warranty Some states do not allow limitations on how long our implied warranty lasts so the above limitation may not imply to you The retailer shall not be liable for incidental consequential or special damages arising out of or in connection with product use or performance except as may otherwise be accorded by law Some states do not allow the exclusion of incidental or consequential damages so the above exclusion or limitation may not apply to you This warranty gives specific legal rights and you may also have other rights which vary from state to state This warranty supersedes all other warranties Lifetime Limited Warranty Date Purchased Store Purchased Model No Serial No Vendor No UPC No Safety RULES rn a A deed ecmd cea detay a ea Page 1 Unpacking Your Room Conditioner Page 3 Installing Your Room Conditioner rtncswdadankstguaseegaasiaeenabentersadtenaaaadsemst Page 4 Operating Your Room Condi Omer Page 11 How 16 56 the Remote ea i ieeede chaise sates suey Ea a E ESSET Page 12 Your Room Con
23. trol is a button with a light bulb symbol on it In order to illuminate the light kit on the Reiker Room Conditioner you must first press the power button The remote control will light up to show that power has been initiated Then press the light button Setting the Dip Switches In the Receiver In the transmitter the dip switches are accessible from the battery compartment as shown in Figure A The dip switches in your Room Conditioner are preset to a particular code in order for your remote control signal to be accepted by the receiver If you have more than one Room Conditioner in a room you may need to change the dip switches In order to change the code in your Room Conditioner you must have the power on Next turn the power off at the wall while the remote power 15 still Then change the settings of the dip switches in the transmitter located near the batteries This should be done with a small pointed object Next turn the power on at the wall and within 30 seconds press the small button next to the dip switches This should be done with a small pointed object The LCD will show the number 5 decrease down to 1 and the light on the Room Conditioner will flash After this the new code will be set If this is not accomplished repeat the steps Dip Switches Battery Compartment Transmitter Figure A IMPORTANT REMOTE MUST BE IN THE SAME ROOM AS THE ROOM CONDITIONER BEST WHEN LOCATED IN THE WAL
Download Pdf Manuals
Related Search