LELY COSMIX Mobile Concentrate Feeder
Contents
1. lt Y ar ul INTENTIONALLY BLANK innovators in agriculture D 1022 1004EN innovators in agriculture D 1022 1004EN TRADEMARKS COPYRIGHT AND DISCLAIMER Lely Astronaut Astri Astrodata Atlantis Attis Calm Commodus Compedes Cosmix Discovery E link Fertiliner Gravitor Grazeway Hibiscus Hubble Juno LAC Lely Center Lelywash Lotus Luna Nautilus Orbiter Shuttle Splendimo TAC Tigo Viseo Voyager and Welger are registered trademarks of the Lely Group The right of exclusive use belongs to the companies of the Lely Group All rights reserved The information given in this publication is provided for information purposes only and does not constitute an offer for sale Certain products may not be available in individual countries and products supplied may differ from those illustrated No part of this publication may be copied or published by means of printing photocopying microfilm or any other process whatsoever without prior permission in writing by Lely Holding S r l Although the contents of this publication have been compiled with the greatest possible care Lely cannot accept liability for any damage that might arise from errors or omissions in this publication The English language manual is the original manual Translations into other languages use the English language manual as the source document Lely accepts no liability f2. 4 13 5 1 5 6 Test the Photoelectric Sensors 4 13 5 1 uy innovators in agriculture INTENTIONALLY BLANK innovators in agriculture D 1022 1004EN Index D 1022 1004EN innovators in agriculture LELY INDUSTRIES NV Weverskade 110 NL 3147 PA Maassluis Tel 31 0 10 59 96 333 Fax 31 0 10 59 96 444 www lely com innovators in agriculture D 1022 1004EN Live Life Lely
3. es Figure 7 Prepare the COSMIX M for transport 5 4 Install the Cosmix Remove the connection cable trailer connector cable and ADANGER the safety cable breakaway cable before putting the COSMIX Mobile Concentrate Feeder in operation a CAUTION Wear safety shoes 1 Make sure the solar panel is in the direction of the sun at 12 00 2 Remove the cables 3 fig 7 page 5 3 and 6 from both the car or tractor and the COSMIX M and store them in a safe place 3 Use the front support column crank 4 fig 7 page 5 3 to raise the coupling 2 above the towbar ball 1 4 Lower both rear support columns to the ground Make sure the COSMIX M is level adjust the columns if necessary Installation 5 3 10 12 13 innovators in agriculture Raise the front support column approximately 1 cm 0 4 in with the crank 4 Lower both rear support columns to the ground Fully lower the front support column with the crank 4 Make sure the columns are firmly standing on the ground adjust them if necessary Make sure the columns are fully tightened Adjust the position of the solar panel to 60 degrees page 8 1 Make sure the cow sizes in the herd are as equal as possible Fold out the fences to the correct position for the herd fig 9 page 5 5 1 sure the width is correct 2 Attach both side fe
4. 2 4 3 Maintenance of Safety Decals Safety decals on the COSMIX Mobile Concentrate Feeder display important and useful information that will help you safely operate and maintain the COSMIX M Obey the instructions below to make sure all the decals stay in the correct position and condition Keep the safety decals clean and legible at all times Clean the safety decals with soap and water Do not use mineral spirits abrasive cleaners or other similar agents that may damage the safety decals Replace safety decals that are missing or are illegible Safety decals can be purchased from your local Lely service provider 2 4 4 Installation of Safety Decals 1 2 Safety Make sure the installation surface is clean and dry Make sure the temperature of the mounting surface is not less than 5 C 41 F Identify the correct position for the decal before you remove the backing paper Remove a small part of the backing paper Put the decal in the correct position on the mounting surface and carefully press the small part of exposed adhesive surface of the decal onto the mounting surface Slowly remove the backing paper and attach the rest of the decal to the mounting surface Puncture small air pockets in the decal with a pin and use the backing paper to smooth the decal 2 6 INTENTIONALLY BLANK innovators in agriculture D 1022 1004EN Safety innovators in agriculture D 1022 1
5. 1004EN Diagrams D 1022 1004EN GLOSSARY OF TERMS approx approximately Astronaut Lely Astronaut A3 milking robot cm centimeter dosing unit pneumatically controlled device for dispensing food E Link manual controller control device used to adjust the settings or manually control the installation EU European Union gal gallon ID reader Cow identification device in inch ISO reader Reader with standardized method and format of transfer of data between sensors kg kilogram kPa kiloPascal Ib pound LED Light Emitting Diode m metre mA milliAmperes multiboard standardized control board used in most Lely products PC Personal Computer PCB printed circuit board with electrical components portion size size of one portion of concentrates psi pounds per square inch Qwes identification tag for ISO identification System Qwes H HR identification tag for Qwes H or Qwes HR identification system Lely Time 4 Cows Farm Management Software titania kit pneumatically controlled unit that dispenses nutrition fluid into the feed bin V Volt yd yard 36 inches Glossary of Terms innovators in agriculture INTENTIONALLY BLANK innovators in agriculture D 1022 1004EN Glossary of Terms D 1022 1004EN INDEX A Adjust the Detection Distance from the Photoelectric 0 5 8 8 Adjust the Position of t
6. 8 6 2 Test the Load Cell Sensors 1 Getthe E Link Manual Controller page 6 2 In the main menu select Testing and push button 4 17 Select Sensors and push button PM Select Load cell and push button 11 Make sure both feed bins empty Make sure the E Link indicates for both feed bins O gr Put a known weight in one of the feed bins Make sure the E Link indicates the known weight Repeat steps 6 and 7 for the other feed bin LM A IE E E 0 Ifthe test fails calibrate the load cell sensors page 8 3 8 6 3 Test the Photoelectric Sensors 1 Get the E Link Manual Controller 6 2 In the main menu select Testing and push button eth Select Sensors and push button et 2 3 4 Select photocell and push button e 5 Make sure the displayed value for both photocells is 0 6 Put a sheet of paper under the left photocell sensor 2 at a distance of approximately 10 cm 4 in D 1022 1004EN Di Make sure the displayed value for sensor 2 is 1 8 Move the sheet of paper down 1 Make sure the displayed value for sensor 2 changes to 0 approximately 50 80 cm 20 31 in above the ground The photoelectric sensor detects objects that are approximately 50 80 cm 20 31 in and more above ground level 9 Ifthe value does not change to 0 within a distance of approximately 50 80 cm 20 31 in above the ground adjust the distance page 8 1 10 Repeat the procedure fo
7. Use buttons I to change the value Push soft button OK to confirm Push button ESC to go up one level Get the E Link Manual Controller page 6 2 In the main menu select Settings and push button el Select Clock and push button al Use soft buttons gt gt or lt lt to select the next or previous item Use buttons TAN or to change the value Push soft button OK to confirm After a few seconds you return to the menu Settings 8 4 7 Set the Display Language 1 2 3 4 5 Get the E Link Manual Controller page 6 2 In the main menu select Settings and push button el Select Language and push button a Use buttons I to change the value Push soft button OK to confirm After a few seconds you return to the menu Settings 8 5 Make Feeding Settings 8 5 1 Set the Feed Dose per Day 1 2 3 Test and Adjustment Get the E Link Manual Controller page 6 2 In the main menu select Feed settings and push button e Select Feeding and push button e 8 5 innovators in agriculture 4 dir buttons to select gr day d and push button lt 5 Use soft buttons gt gt lt lt to select the next or previous item 6 Use buttons I to change the value 7 Push soft button OK to confirm 8 5 2 Set the Maximum Credit 1 Getthe E Link Manual Controller page 6 2 2
8. correctly installed Make sure it is correctly supported at all times during movement and installation Make sure the concentrate feeder is correctly installed Safety innovators in agriculture D 1022 1004EN 2 3 4 Operating Safety Read and understand the applicable manual and all safety signs before you connect power supplies to operate maintain or adjust the COSMIX Mobile Concentrate Feeder Only trained persons are permitted to operate the COSMIX Mobile Concentrate Feeder Install all covers and guards before you operate the COSMIX Mobile Concentrate Feeder Keep hands feet hair and clothing away from all moving parts Keep unauthorized persons especially small children away from the COSMIX Mobile Concentrate Feeder at all times Always be alert for unexpected movement of the cow Cows can transmit large forces to parts of the machine Contact your nearest Lely service provider if you have any questions Review safety related items with all operators frequently annually 2 3 5 Maintenance Safety Read and understand the applicable manual and all safety signs before you connect power supplies to operate maintain or adjust the COSMIX Mobile Concentrate Feeder e Only trained persons are permitted to maintain the COSMIX Mobile Concentrate Feeder e Disconnect and isolate the electrical power supply before you clean or do maintenance on the COSMIX Mobile Concentrate Feeder e
9. in death or serious injury Indicates a potentially hazardous situation that if not avoided could result in death or serious injury and includes hazards that are exposed when guards are removed Indicates a potentially hazardous situation that if not avoided may result in minor or moderate injury or product or property damage This shows extra information that may help the reader 2 1 2 3 2 3 1 2 3 2 2 3 3 innovators in agriculture Safety Instructions YOU are responsible for the SAFE operation and maintenance of your concentrate feeder YOU must make sure that you and anyone else who is going to operate maintain or work in the vicinity of the concentrate feeder knows all the related SAFETY information in this manual YOU are the key to safety Good safety practices protect you and the people around you Make these practices a working part of your safety program Make sure EVERYONE who operates maintains or works near the concentrate feeder obeys the safety precautions Do not risk injury or death by ignoring good safety practices General Safety Electrical Safety COSMIX M owners must train operators before they operate the concentrate feeder This training must be repeated at least annually The operator must read understand and obey all safety and operating instructions in the manual A person who has not read and understood all safety and operating instructions is not permitted to operate the conce
10. the COSMIX M 8 2 Display the Software Version 1 Getthe E Link Manual Controller page 6 2 2 Inthe main menu select Settings and push button e 3 Select Software version and push button eal 8 3 Adjust the COSMIX M 8 3 1 Adjust the Position of the Solar Panel 1 Loosen the handles 2 fig 8 page 5 4 of the mechanism that keeps the solar panel in its position 2 Turn the solar panel 1 until the angle with the ground is approximately 60 degrees 3 Fully tighten the two handles 4 Make sure the solar panel in a position to receive maximum solar light 8 3 2 Adjust the Detection Distance from the Photoelectric Sensors 1 Remove the bracket that attaches the photoelectric sensor to the frame 2 Turn the set screw e Clockwise to enlarge the detection distance nearer to the ground Counterclockwise to lower the detection distance further away from the ground 3 Install the bracket with the photoelectric sensor on the frame Test and Adjustment 8 1 uy innovators in agriculture 8 4 8 4 1 8 2 DISTANCE Ay D 1022 1004EN Figure 13 Adjust the detection distance from the photoelectric sensor Make Basic Software Settings Adjust the Refill Level of the Feed Bin Find out the best refill level If it is too high dominant cows will be encouraged push away the eati
11. the COSMIX M Connect the COSMIX M Setup the software List of Supplied Parts The COSMIX M and the accessory package must contain the parts listed below Make sure all these items are present before you start the installation If items are missing contact your local Lely service provider COSMIX M vehicle E Link manual controller Trailer connector cable connection cable Breakaway cable safety cable Operator manual Operating instructions Solar Charge Controller in the control box Assemble and test the COSMIX M 1 Assemble the COSMIX M refer to the assembly instructions F M001 1001VT Make sure the battery selection jumpers in the solar charge controller are set to Gel refer to the manual Operating instructions Solar Charge Controller Make sure the pink colored wires to the two ID readers connected with each other fig 6 page 4 8 Make sure the gray colored wires to the two ID readers are connected with each other Test the photocells page 8 8 Set the ID sensors page 8 4 Test the ID sensors page 8 8 Calibrate the load cell sensors page 8 3 Test the load cell sensors page 8 8 If the test results are not correct repeat steps 8 and 9 Test the auger motors page 8 7 Make sure the rear lights brake lights and turn signals function correctly 5 1 5 3 Preparation 5 3 1 Preparation by the Owner Before the installation can be done same tasks must be done by th
12. 004EN 3 SPECIFICATIONS 3 1 Dimensions and Weight Height 230 cm 90 5 in Length 405 cm 159 5 in Width 285 cm 73 in Weight approx 665 kg 1466 Ib Feed hopper capacity 1400 369 gal 3 2 Batteries e No of batteries 2 e Type CPC110 gel e Voltage and capacity 12 VDC 110 Ah Batteries are connected in series to make 24 VDC 3 3 Speed e Maximum speed 40 km h 25 mph Specifications 3 1 3 2 INTENTIONALLY BLANK innovators in agriculture D 1022 1004EN Specifications D 1022 1004EN innovators in agriculture 4 DESCRIPTION AND OPERATION 4 1 Introduction The COSMIX M supplies exact portions of concentrates to the visiting cows up to a calculated total The information about the portion size is stored in the control system The control system calculates for each cow the feed credit based the previously supplied amount and the allowed total consumption Each cow can be assigned to a group with set feeding characteristics The cow is identified by the ISO identification system The ISO identification system has a MIMI antenna to identify FDX and or HDX ear tags The COSMIX M is installed in the field The COSMIX M has the following main parts e Trailer wagon Feeding station for two cows Fencing e Control unit with E Link manual controller Power system e Cow detection system The COSMIX M is not connected to a data network
13. 1022 1004EN Introduction innovators in agriculture 1 INTRODUCTION The COSMIX Mobile Concentrate Feeder is a stand alone feeding system that supplies the correct amount of concentrates to each cow individually based on her built up feed credit and a previously set total amount An electronic tag on each cow enables the system to identify the cow via an unique number The control system has information about each cow and adjusts the feed amount based on this information The information in this manual is for farmers and technicians e Farmers use the information to operate and setup the COSMIX M e Technicians use the information to setup the COSMIX M 1 1 1 2 INTENTIONALLY BLANK innovators in agriculture D 1022 1004EN Introduction innovators in agriculture D 1022 1004EN 2 1 2 2 2 SAFETY Introduction The safety alert symbol identifies important safety messages on your COSMIX Mobile Concentrate Feeder and in the manual When you see this symbol be alert to the possibility of personal injury or death Follow the instruction of the safety message Safety Alert Symbol Signal Words ADANGER AWARNING CAUTION Safety Note the use of the signal words DANGER WARNING and CAUTION with the safety messages The signal word for each message uses the following guidelines Indicates an imminently hazardous situation that if not avoided will result
14. 4 2 Component Description 4 2 1 Trailer Wagon Description and Operation The feeding station is built upon a trailer wagon The trailer wagon is suited for driving behind a car or a tractor on the field or on the public road The trailer wagon has e Frame e Wheels 2x e Draw bar with coupling e Support columns 1x front 2x rear e Crank to lift the front support column e Rear lights brake lights and turn signal e Trailer connector cable connection cable Breakaway cable safety cable e Top canvas e Side canvas 2x e Back canvas 4 1 4 2 ELY COSMIX M WWW COM Figure 1 Trailer wagon KEY 1 Top canvas 2 Side canvas 3 Rear lights brake lights and turn signal 4 Rear support column 5 Frame 6 Front support column 7 Trailer connection cable 8 Breakaway cable 9 Draw bar with coupling 10 Crank Description and Operation innovators in agriculture D 1022 1004EN uy D 1022 1004EN innovators in agriculture Feeding Station There are two feeding stations to feed two cows simultaneously The feedings stations are built upon the trailer wagon and have the following parts e Feed hopper e Dosing unit 2x each with e Auger e Auger motor with encoder e Feed b
15. Get the E Link Manual Controller page 6 2 In the main menu select Feed settings and push button 11 Select the group the is and push button Select REMOVE COW Push soft button OK to confirm Push button ESC to go up one level Get the E Link Manual Controller page 6 2 In the main menu select Feed settings and push button el Select the group the cow is in and push button e Push buttons A or to select the cow and push button Use soft buttons gt gt lt lt to select the next or previous item Use buttons LN to change the value Push soft button OK to confirm 8 6 Test the Operation of the COSMIX M 8 6 1 Test the Auger Motors Test and Adjustment Danger of being entangled by rotating parts Keep hands loose clothing and long hair away from moving parts during operation of the COSMIX M 1 JY UD de W p Get the E Link Manual Controller page 6 2 In the main menu select Testing and push button xd Select Motors and push button Select Test auger 1 and push button e Push soft button Make sure the auger motor turns If the auger motor does not turn 1 Push button and immediately after that button Stop 2 Repeat steps 4 to 6 3 Ifthe auger motor does not turn clean the auger page 9 1 Select Test auger 2 and push button e Repeat steps 4 to 6 8 7 innovators in agriculture
16. Inthe main menu select Feed settings and push button el 3 Select Feeding and push button 1 4 Push buttons to select credit d and push button jay 5 Use soft buttons gt gt or lt lt to select the next or previous item 6 Use buttons to change the value 7 Push soft button OK to confirm 8 5 3 Set the Entrance Credit 1 Getthe E Link Manual Controller page 6 2 2 Inthe main menu select Feed settings and push button e 3 Select Feeding and push button e D 1022 1004EN 4 Push buttons UN or to select Ent credit d and push button 11 5 Use soft buttons gt gt lt lt to select the next or previous item 6 Use buttons LN to change the value 7 Push soft button OK to confirm 8 5 4 Move a Cow to another Group New identified cows are default put in group 8 1 Get the E Link Manual Controller 6 2 2 Inthe main menu select Feed settings and push button e 3 Select the group the is in and push button e 4 Push buttons UN or select the cow and push button el 5 Push buttons VN select the new group and push button e 6 Push button ESC to go up one level 8 6 Test and Adjustment D 1022 1004EN innovators in agriculture 8 5 5 Remove a Cow from the Database 1 2 3 4 5 6 8 5 6 Set a Cow Name 1 2 3 6 7
17. Link Manual Controller is connected to the left side of the multiboard PCB box The E Link has the following buttons e Button 1 confirms the action on the LCD display above the applicable button e Button 2 starts or stops an action Button 3 opens the selected function or the next menu screen e Button 4 returns to the previous screen e Button 5 moves the selector down one item decreases a value by one or confirms a command e Button 6 moves the selector up one item increases a value by one or confirms a command The E Link Manual Controller 4 3 E Link Software User Interface The table shows the menu structure of the E Link software user interface Feed settings gt Group 1 gt Feeding p Move Remove cows Set cow name Return n pes ooo Low consumption gt Cow oo D ew _ Enc Augers E moe Reset Clear DB gt Reset print Clear data base Clear feed amount 4 10 Description and Operation innovators in agriculture D 1022 1004EN D 1022 1004EN innovators in agriculture mue _ Food bin Loadcell 1 ee Calibration Antenna 1 Antenna 2 Power level Squelch level ewm Mee SSCS 4 3 1 Feed Settings The submenu Feed settings is used to set per gro
18. MIX M in Operation 1 Open the left side canvas 2 Open the control box 3 Push the right button fig 11 page 6 1 on the solar charge controller 4 Ifthe display on the solar charge controller indicates an error reset the power system page 9 3 Figure 11 Take the COSMIX M out of operation Operating Instructions 6 1 6 3 Fill the Feed Hopper 1 Remove the top canvas fig 12 page 6 2 Fill the feed hopper with concentrates Install the top canvas a w If the feed type or humidity is different from before set the portion size page 8 4 Figure 12 Remove the top canvas 6 4 Get the E Link Manual Controller 1 Open the side canvas on the left side 2 Get the E Link Manual Controller 3 Push ESC or eli to wake up the E Link The E Link Manual Controller automatically goes into sleep mode when it is not used for 10 minutes 6 2 Operating Instructions innovators in agriculture D 1022 1004EN innovators in agriculture D 1022 1004EN 6 5 6 6 6 7 6 8 Display the actual Status 1 Get the E Link Manual Controller 6 2 2 Inthe main menu select Working and push button 11 List Details about the last Visits 1 Get the E Link Manual Controller 6 2 2 Inthe main menu select Repo
19. Make sure all covers and guards are installed when maintenance work is complete 2 4 Safety Decals 2 4 1 Safety Decal Messages Safety General safety messages appear in this safety messages section Specific safety messages are in applicable parts of this manual when potential hazards may occur if the instructions or procedures are not followed Rotating Parts Entanglement Hazard Symbol Danger of being entangled by rotating parts Keep hands loose clothing and long hair away from moving parts during operation of the COSMIX M innovators in agriculture A DANGER ELECTROCUTION HAZARD BEFORE SERVICING TURN POWER OFF WAIT FOR ALL MOVING PARTS STOP e DISCONNECT OR SWITCH OFF MAIN SWITCH Danger Electrocution Hazard Symbol Danger of electrocution Keep hands away from all live parts when A WARN ING you open the control box of the COSMIX M D 1022 1004EN Remove the connection cable trailer connector cable and the safety cable breakaway cable before putting the COSMIX Mobile Concentrate Feeder in operation ADANGER A DANGER Maximum speed of the COSMIX M is 40 km h 25 mph 2 4 2 Position of the Safety Decals Rotating Parts Entanglement On both feed augers Hazard Electrocution Hazard On the door of the control box Maximum Speed On the back canvas Remove Cables On the front support column 2 4 Safety innovators in agriculture D 1022 1004EN
20. X M except for the maintenance done by the operator as indicated in the Operator Manual If people who are not certified by Lely Industries do maintenance on the COSMIX M the warranty on the COSMIX M becomes invalid Before a technician does maintenance on an COSMIX M the owner must examine the service pass of the technician and make sure the technician is currently certified to do maintenance on the COSMIX M At the end of each visit all work done on the COSMIX M must be written in the logbook and the logbook must be signed by the certified technician The logbook must always be kept near the COSMIX M for the entire life of the product The information in the logbook must include The maintenance done The date of the maintenance The name of the technician The certification number of the technician D 1022 1004EN innovators in agriculture Technician Training All the technicians certified by Lely Industries have completed an approved training program and passed written and practical examinations during and at the end of the training program The training is given by a product specialist The examinations are done under supervision of a master product specialist and include troubleshooting and corrective maintenance of the COSMIX M There are five certification levels e Installation Technician certification valid for two years e Service Engineer certification valid for two years e Senior Service Engineer cer
21. and washers 6 Install the latch with the wing nuts and washers 9 1 innovators in agriculture 3 001 01 T g hi Ie YY egg IW Ly Figure 14 Clean the auger Troubleshooting 9 2 D 1022 1004EN innovators in agriculture Figure 15 Remove install the auger cover 9 2 2 Reset the Solar Charge Controller A reset is necessary when the power supply from the batteries has been interrupted 1 Cover the solar panel with a cloth 2 Disconnect the connector from the E Link manual controller from the control box The solar module produces electricity when exposed to light Cover all AWARN IN G modules in the solar panel with opaque material before making any wiring connections or opening the control box 3 Open the control box Troubleshooting 9 3 4B 9 som 11 12 13 innovators in agriculture Remove jumper CON201 from the multiboard pcb Disconnect one of the cables to the solar panel on the left side of the solar charge controller Insulate the copper wire with insulation tape Disconnect the fuse Connect the fuse Remove the insulation tape from the cable to the solar panel Connect the cable to the solar charge controller Wait until the display on the solar charge controller dis
22. ce Description and Operation D 1022 1004EN 4 2 4 Power System innovators in agriculture The power system generates stores and distributes the electrical power for the driving mechanism the control system and the feed system It has the following primary parts e Solar panel e Solar charge controller Battery 2x e Fuse The solar panel is on top of the COSMIX M the solar charging controller and the fuse are in the control unit and the two batteries are installed on the frame of the trailer wagon each on a side The power system sends output to the multiboard pcb Figure 4 Power system KEY 1 Solar panel 2 Control box with solar charge controller 3 Battery one out of two Description and Operation innovators in agriculture 4 2 5 4 2 5 1 4 2 5 2 Cow detection System The cow detection system detects and identifies cows that enter the feeding station It has the following parts Photoelectric sensors to detect a cow e The ISO identification system to identify a cow Photoelectric Sensor ISO Identification Both feeding stations have a photoelectric sensor to detect a visiting cow fig 5 page 4 7 The sensors are installed on the top frame of each
23. e owner of the COSMIX M with support from the Lely service provider Example tasks are Make sure all cows have an FDX or HDX tag in the right ear Read and understand the COSMIX M user manual 5 3 2 Transport the COSMIX M Do not lift the draw bar by hand CAUTION CAUTION Use the front support column crank 4 fig 7 page 5 3 to raise the coupling 2 above the towbar ball 1 Make sure the coupling is in the correct position above the towbar bal Lower the coupling on the towbar bal Fully raise the front support column 5 with the front support column crank 4 Connect the breakaway cable 3 to both the car or tractor and the COSMIX M Connect the trailer connector cable to the connectors on both the COSMIX M and the car or tractor 6 Make sure the rear lights brake lights and turn signal function correctly Adjust the solar panel 1 fig 8 page 5 4 to the transport position approximately horizontal Make sure the handle 2 is fully tightened Set the fences in the smallest position fig 10 page 5 6 Maximum speed of the COSMIX M is 40 km h 25 mph Only transport the COSMIX M connected to a towbar on the rear side of a car or tractor 11 Transport the COSMIX M to a position where the solar panel will receive maximum sunlight Installation innovators in agriculture D 1022 1004EN innovators in agriculture D 1022 1004EN
24. enna 1 and push Select soft button START Connect the connector to feed bin 1 to the joined connector to CON401 Wait until the E Link display displays the text ID ready D 1022 1004EN Push button ESC to go up one level Disconnect the connect to feed bin 1 from the joined connector to CON401 Select Antenna 2 and push button et Select soft button START Connect the connector to feed bin 2 to the joined connector to CON401 Wait until the E Link display displays the text ID ready ESC to go to the previous menu Connect the connector to feed bin 1 to the joined connector to CON401 Close the control box Test the ID sensors page 8 8 8 4 5 Set the Portion Size 1 2 3 Get the E Link Manual Controller page 6 2 In the main menu select Settings and push button el Select Dispensing and push button 8 1 Test Adjustment D 1022 1004EN innovators in agriculture Calculate the supplied portion 1 2 3 4 5 Select Portions Rev 1 for feed bin 1 or Portions Rev 2 for feed bin 2 and push button 11 In the menu FOOD PORTION push button START Wait until the counter displays 10 Weigh the supplied feed with a balance Calculate the portion size weighted amount 10 Set the portion size 8 4 6 Set the Time Boe qe gt Push button SET Use soft buttons gt gt or lt lt to select the next or previous item
25. feeding station fig 5 page 4 7 The photoelectric sensors have a housing that contains an emitting element infrared LED and a receiving element photodiode The detection distance can be adjusted to the dimensions of the herd and must be set well above ground level to avoid detecting other animals or objects The photoelectric sensor gets input when a cow is in the COSMIX M The photoelectric sensor sends output to the multiboard pcb System The ISO identification system has two components e The HDX or FDX ear tag e The MIMI antenna D 1022 1004EN The ear tag is installed in the right ear of the cow The MIMI antenna is in a sealed plastic box that is installed on the side frame near the feed bin The data cable of the antenna is connected to the multiboard pcb Description and Operation D 1022 1004EN innovators in agriculture 4 2 6 Control Unit Description and Operation Figure 5 Cow detection system KEY 1 Photoelectric sensor 2 2 Photoelectric sensor 1 3 ID reader 1 4 ID reader 2 The control unit controls the supply of feed and the power supply It is installed in the control box on the left side of the COSMIX M and has the following parts Multiboard pcb e Solar charge controller The control software t
26. he Solar Panel 5 4 Adjust the Refill Level of the Feed Bin 4 13 C Calibrate the Load Cell Sensors 4 13 5 1 5 6 8 8 Clean the 8 7 9 1 Connection 4 3 8 4 D Display the Software Version 4 13 F Feeding 5 4 7 G Get the E Link Manual Controller 6 3 8 1 8 2 8 3 8 4 8 5 8 6 8 7 8 8 L List of Supplied 9 4 M Move a Cow to another Group 4 12 P Photoelectric 4 7 Power idee edo ads 4 7 R Remove a Cow from the Database 4 12 Reset the Solar Charge Controller 6 1 9 1 S Set a Cow 4 12 Set the Antennas 4 13 5 1 8 9 Set the Display Language 4 13 Set the Entrance 4 11 Set the Feed Dose per Day 4 11 Set the Maximum 4 11 Set the Portion 517 5 6 6 2 Set ihe 4 13 Set the Weighing Unit ON or OFF 4 13 Index T Test the Auger Motors 4 13 5 1 9 1 Test the ID Sensors 4 13 5 1 8 4 Test the Load Cell Sensors
27. ies 3 3 Speed Description and Operation 4 1 Introduction 4 2 Component Description 4 2 1 Trailer Wagon 4 2 2 Feeding Station 4 2 3 Fencing 4 2 4 Power System 4 2 5 Cow detection System 4 2 6 Control Unit 4 2 7 E Link Manual Controller 4 3 E Link Software User Interface 4 3 1 Feed Settings 4 3 0 Working 4 3 3 Reports 4 3 4 Testing 4 3 5 Settings 4 4 Operation 4 4 1 Identification 4 4 2 Feeding Process 1 1 2 1 2 1 2 1 2 2 2 2 2 2 2 2 2 3 2 3 2 3 2 3 2 4 2 5 2 5 3 1 3 1 3 1 3 1 4 1 4 1 4 1 4 3 4 4 4 5 4 6 4 7 4 9 4 10 4 11 4 12 4 12 4 13 4 13 4 13 4 13 4 13 innovators in agriculture xi 5 xii Installation 5 1 Introduction 5 2 Assemblage 5 2 1 List of Supplied Parts 5 2 2 Assemble and test the COSMIX M 5 3 Preparation 5 3 1 Preparation by the Owner 5 3 2 Transport the COSMIX M 5 4 Install the Cosmix 5 5 Setup the COSMIX M Operating Instructions 6 1 Take the COSMIX M out of Operation 6 2 Put the COSMIX M in Operation 6 3 Fill the Feed Hopper 6 4 Get the E Link Manual Controller 6 5 Display the actual Status 6 6 List Details about the last Visits 6 7 List Details about Cows with low Consumption 6 8 List Details per Group about the last 24 Hours 6 9 List Attentions Maintenance Test and Adjustment 8 1 Introduction 8 2 Display the Software Version 8 3 Adjust the COSMIX M 8 3 1 Adjust the Position of the Solar Panel 8 3 2 Adj
28. in 2x e Load cell sensor 2x The auger motor gets inputs from the multiboard pcb fig 18 page 10 3 The auger motor encoder sends outputs to the multiboard pcb The load cell sensors send outputs to the multiboard pcb Figure 2 Feeding station without covering KEY 1 Feed hopper 2 Feed bin 1 3 Feed bin 2 4 Auger 1 5 Auger 2 Description and Operation 4 3 4 2 3 Fencing innovators in agriculture The fences must make sure that the eating cows are not disturbed by other cows The COSMIX M has the following fences Middle fence to separate the two parts of the feeding station e Side fence 2x to enclose the cow on the side e Sub fence 2x to enlarge the side fence long cows e Upper bracket 2x to keep the fencing in position The distance between the side fences and the middle fence must be adjusted to the width of the cows The length of the side fence together with the sub fences must be adjusted to the length of the cow D 1022 1004EN Figure 3 Fencing without side canvas KEY 1 Sub fence 2 Top fence 3 Side fence 4 Setting positions for side fence 5 Middle fen
29. is known that means if her tag number is in the database the feeding process starts If the cow is not known the feed station supplies portions of feed based on the settings of the default group 8 The tag number is stored in the default group 8 As long as the cow is in the feed station the photocell detects her presence This makes sure the feeding process is continued if the ID detection signal is interrupted Feeding Process Start of visit Feeding starts when e the cow is identified e the maximum credit is more than the entrance credit If these conditions are met the feed dosing unit supplies portions of feed sized the refill level plus an extra portion The load cell measures the amount of feed in the feed bin If the amount drops below the refill level and the maximum credit is not reached the COSMIX M supplies an extra portion End of visit The supply of feed continues until e the cow left the feeding station e the maximum credit is reached At the end of the visit the amount eaten is stored in the database Leftovers are added to the feed portion of the next visiting cow Description and Operation innovators in agriculture D 1022 1004EN D 1022 1004EN 5 1 5 2 5 2 1 5 2 2 Installation innovators in agriculture 5 INSTALLATION Introduction The installation process of the COSMIX M has the following phases Assemblage Prepare the installation Install
30. latest information that was available at the time of publication Your COSMIX M may comprise improvements features or options that are not covered in this manual The table below shows the type numbers of COSMIX M for which this manual is applicable Model designation COSMIX Mobile Concentrate Feeder 5 2306 0000 1 Standard Torque Loading of Parts All the nuts bolts and screws used on the COSMIX Mobile Concentrate Feeder are torque tightened to standard torque loadings applicable to the construction materials used If a part has a non standard torque loading it is specified in the applicable part of the manual vii Registration Maintenance Authorization viii innovators in agriculture The Type and Serial Number Plate is attached to the middle fence of the COSMIX Mobile Concentrate Feeder Always include the type and serial number of your concentrate feeder when you contact your local Lely service provider or order spare parts LELY INDUSTRIES NV 3147 PA MAASSLUIS THE NETHERLANDS Type e Ser Nr kg V Hz and Serial Number Plate We suggest you complete the table below with the type and serial numbers of your concentrate feeder This makes sure you can easily find the information Type number Serial number D 1022 1004EN Only technicians certified by Lely Industries are authorized to do maintenance on the COSMI
31. list can be cleared with button Clear list The menu Testing is used to e Test the auger motors page 8 7 Test the following sensors e Load cell this procedure must be done after the COSMIX M has been transported page 8 8 e Identification this procedure must be done during installation or troubleshouting page 8 8 photocell this procedure must be done during installation or troubleshouting page 8 8 e Encoder auger motors this procedure must be done during installation or troubleshouting Reset or clear e Reset print Clear data base Clear the feed amount The reset and clear procedures are only done during troubleshooting The menu Settings is used to Set the portions sizes and refill levels page 8 2 Set the weighing system page 8 3 Set the weighing unit ON or OFF page 8 3 Set the displayed attentions Set the identification system page 8 4 Set the internal clock and the display language page 8 5 page 8 5 Display the software version page 8 1 Settings are done during installation It can be necessary to adjust settings when for example the feed type is changed the herd is changed or the COSMIX M is transported Cow Identification A cow enters the COSMIX M and stands in front of the feed bin The photocell above the cow detects her presence and the antenna in the ID reader reads the tag of the cow The ID reader sends the data of the tag to the control unit If the cow
32. n moist feed clean the auger page 9 1 The auger motor does not turn The feed is delivered too fast The solar charge controller indicates a power failure The solar charge controller indicates that the battery voltage is too low E07 The cow recognition and Call your local Lely service provider feed delivery starts when the cow is away from the feed unit The power supply to the Reset the power system page 9 3 batteries has been interrupted e Not enough sun Make sure the solar panel faces the e Weak battery sun Charge both batteries with a battery charger that is suitable for charging gel batteries Make sure both batteries have the same voltage If the voltage of one of the batteries is lower than the other replace both batteries with similar batteries from the same production series 9 2 Recovery Procedures 9 2 1 Clean the Auger Troubleshooting Danger of being entangled by rotating parts Keep hands loose clothing and long hair away from moving parts during operation of the COSMIX M 1 Remove the two wing nuts 1 fig 14 page 9 2 and washers that attaches the latch to the auger housing 2 Rotate the latch 180 degrees 2 and slide it into the slot 3 in the feed supply pipe 3 Remove the six nuts and washers fig 15 page 9 3 that attach the covering of the auger to the auger housing 4 Remove any dirt from the auger Install the covering of the auger with the six nuts
33. nces to the frame fig 10 page 5 6 Make sure the length is correct fig 9 page 5 5 1 Fold back the sub fence for small cows 2 Fold out the sub fence for big cows 3 Tighten the bolts to secure the sub fence D 1022 1004EN Figure 8 Adjust the solar panel Installation D 1022 1004EN innovators in agriculture 100 cm 39 4 in 220 cm 86 6 in 45 cm 70 cm 17 7 in 27 6 in Figure 9 Minimum and maximum cow dimensions Installation 5 5 Figure 10 Adjust the fences 5 5 Setup the COSMIX M 1 Calibrate the load cell sensors page 8 3 2 Test the load cell sensors page 8 8 3 Ifthe test results are not correct repeat steps 1 and 2 4 Set the portion size for each feed station page 8 4 5 6 Installation uy innovators in agriculture D 1022 1004EN D 1022 1004EN innovators in agriculture 6 OPERATING INSTRUCTIONS 6 1 Take the COSMIX M out of Operation 1 Open the left side canvas 2 Open the control box 3 Push the right button fig 11 page 6 1 on the solar charge controller The power supply to the multiboard pcb is interrupted the battery charge process continues 4 Close the left side canvas 6 2 Put the COS
34. ng cow to steal rest food If it is too low the feeding time will be long 1 aN Get the E Link Manual Controller page 6 2 In the main menu select Settings and push button el Select Dispensing and push button el Select Refill level 1 for feed bin 1 or Refill level 2 for feed bin 2 and push button ucl Use soft buttons gt gt or lt lt to select the next or previous item Use buttons TAN or I to change the value Test and Adjustment D 1022 1004EN 7 8 innovators in agriculture Push soft button OK to confirm Push button ESC to go up one level 8 4 2 Calibrate the Load Cell Sensors 1 SOP 209 OY duo Sedo JD 10 11 12 Get the E Link Manual Controller page 6 2 In the main menu select Settings and push button 1 Select Food bin push button e Select Load cell 1 and push button e Select Calibration Make sure both feed bins are empty In the menu CALIBRATE BIN push soft button Next Put a known weight approximately 1 kg 2 2 16 in feed bin 1 Adjust the field Weight to the known weight 1 Select the position you want to change with button gt gt 2 Use buttons I to change the value 3 Push soft button OK to confirm Push button ESC to go up one level Select Load cell 2 and push button el Repeat steps 4 to 9 for feed bin 2 8 4 3 Set the Weighing Unit ON
35. ntrate feeder Do not modify the equipment in any way Unauthorized modification may impair the function and or safety and could affect the life of the equipment and persons Only use approved spare parts and make sure they are only installed by authorized technicians Read and understand the manual and all safety signs before you connect power supplies to operate maintain or adjust the COSMIX Mobile Concentrate Feeder Only trained persons are permitted to operate the COSMIX Mobile Concentrate Feeder Install all protective covers and guards before you operate the COSMIX Mobile Concentrate Feeder Wear the correct protective clothing and equipment Disconnect and isolate the electrical power supply before you clean or do maintenance on the concentrate feeder Know the emergency medical center number for your area Contact your nearest Lely service provider if you have any questions Review safety related items with all operators frequently annually The maximum speed during transportation is 40 km h 25 mph The COSMIX Mobile Concentrate Feeder must only be transported by a car or tractor connected tot the towbar at the rear of the vehicle D 1022 1004EN Replace any damaged electrical lines conduits switches and components immediately Isolate the electrical power supply before you work on the electrical system Installation Safety Read and understand the instructions in this manual The concentrate feeder is not stable until it is
36. ogether with the local database on the multiboard pcb control the supply of feed The solar charge controller controls the loading process of the batteries The multiboard gets input from E Link manual controller Cow Identification readers Photoelectric sensors page 4 6 Encoder auger motors page 4 3 Load cell sensors page 4 3 Solar charge controller page 4 5 innovators in agriculture z e e g e Laptop only for service The multiboard sends output to e E Link manual controller e Photoelectric sensors e Auger motors e Laptop only for service The solar charge controller gets input from e Solar panels e Batteries The solar charge controller sends output to e Multiboard pcb e Batteries Figure 6 Control unit with E Link manual controller KEY 1 E Link manual controller 2 Multiboard pcb 3 Solar charge controller 4 8 Description and Operation D 1022 1004EN innovators in agriculture 4 2 7 The E Link Manual Controller Description and Operation The E Link Manual Controller controls and monitors the COSMIX M and communicates with the management software The E link Manual Controller has an LCD display and nine buttons that enable the user to give commands and change values in the COSMIX M The LCD display also shows reports and alarms The connector of the E
37. or OFF Test and Adjustment 1 2 3 Get the E Link Manual Controller page 6 2 In the main menu select Settings and push button Select Food bin and push button 11 Set the load cell ON of OFF 1 Select Load cell 1 for feed bin 1 or Load cell 2 for feed bin 2 and push button 11 2 Use soft buttons gt gt lt lt to select the feed bin and push button 1 3 Use soft buttons gt gt or lt lt to select the next or previous item 4 Use buttons to change the value 5 Push soft button OK to confirm Set the feed speed The default value of the feed speed is 50 gr min Use soft buttons gt gt or lt lt to select the next or previous item 8 3 2 3 4 8 4 4 Set the Antennas innovators in agriculture Use buttons to change the value Push soft button OK to confirm Push button ESC to go up one level Danger of electrocution Keep hands away from all live parts when AWARN ING you open the control box of the COSMIX M Du 10 11 12 13 14 15 16 17 18 19 20 Open the control box Remove the connectors from the joined connector to CON401 on the multiboard pcb page 10 3 Find the connector to feed bin 1 and feed bin 2 Get the E Link Manual Controller page 6 2 In the main menu select Settings and push button el Select Food bin and push 141 Select Ant
38. or discrepancies between the original English language manual and versions in other languages If there is a conflict over the content and accuracy of any translated manual the English language manual is the authority document Copyright O 2010 Lely Industries N V All rights reserved Lely Industries N V Weverskade 110 3147 PA Maassluis the Netherlands Phone 31 0 10 5996333 Fax 31 0 10 5996403 Website www lely com INTENTIONALLY BLANK innovators in agriculture D 1022 1004EN innovators in agriculture LIST OF INCLUDED AMENDMENTS Initial issue D 1022 1004EN vi INTENTIONALLY BLANK innovators in agriculture D 1022 1004EN innovators in agriculture D 1022 1004EN Manual Contents Applicability PREFACE This manual contains the information necessary for the correct installation and operation of a COSMIX Mobile Concentrate Feeder Study and understand this information thoroughly before configuration of the COSMIX M Failure to do so could result in damage to equipment Please consult your local Lely service provider if you do not understand the information in this manual or if you need additional information All information in this manual has been compiled with care Lely shall not be liable for errors or faults in this manual The recommendations are meant to serve as guidelines All instructions pictures and specifications in this manual are based on the
39. oved from the database A cow is identified on her Tag id and the cow information is displayed accordingly You can set for each cow a name that is easier to identify for example the last three digits of the Tag id The submenu Working displays the actual status of identified cows in both feed stations e Tag id e Weight of the feed e Feed credit e Consumed feed in the last day in kg e Supplied feed in kg The submenu Reports is used to display the following reports e Last visit lists details of the last visits e Cow name e Group number Consumed quantity e Time D 1022 1004EN This report can be used to list per cow the consumed feed quantity and the time of the last visit e consumption lists all low consuming cows e Cow name e Group number e Consumed quantity in the last 24 hours This report gives an overview of all cows that did not eat their feed dose during the last day Cow consumption list per group e Cow Average consumed quantity e Days e Group 24 hr report list per group for the last 24 hours e Cow Consumed quantity Number of visits e Attentions e Type of the attention Name of the attention e Time the attention first occurred Description and Operation D 1022 1004EN 4 3 4 4 3 5 4 4 4 4 1 4 4 2 Description and Operation Testing Settings Operation innovators in agriculture The
40. plays a smiling face symbol and a energy saving lamp symbol Install the jumper CON201 on the multiboard pcb Connect the connector from the E Link manual controller to the control box If the display on the solar charge controller indicates an error refer to the Operating instructions Solar Charge Controller page 5 1 D 1022 1004EN Troubleshooting innovators in agriculture 10 DIAGRAMS Dimensions of the COSMIX M 10 1 Y Y X Y X X X 405 cm 3 001 01 159 5 Figure 16 Dimensions of the M 10 1 Diagrams innovators in agriculture 10 2 Cow Dimensions i n 100 cm 39 4 in 220 cm m ae 86 6 in dr 45 cm 70cm 17 7 in 27 6 in Figure 17 Minimum and maximum cow dimensions 10 2 Diagrams innovators in agriculture Connection Diagram 10 3 2 Iapeo TN C pacan y dues 00 8 tay 5 3 29 hhh ON LA X NON oS OEC CIC 3 001 01 Figure 18 Connection diagram 10 3 Diagrams 10 4 INTENTIONALLY BLANK innovators in agriculture D 1022
41. r the right photocell sensor 1 8 6 4 Test the ID Sensors 1 Get the E Link Manual Controller page 6 2 2 Inthe main menu select Testing and push button oti 3 Select Sensors and push button et 4 Select Identification and push button et 5 Make sure the E Link displays No cow and No Tag for both ID1 and 102 8 8 Test and Adjustment D 1022 1004EN Test and Adjustment innovators in agriculture Put an object under both photocells and keep them there Put an ID tag next to feed bin 2 Make sure ID2 displays a Tag id while COW 1 If ID2 displays no Tag id set the antennas page 8 4 Remove the ID tag Make sure the values for COW and TAG do not change Put the same ID tag next to feed bin 1 Make sure the E Link displays No Cow and No TAG for ID 1 Put a different ID tag next to feed bin 1 Make sure ID2 displays a id while COW 1 Remove the ID tag Make sure the values for COW and TAG do not change Remove both objects that activate the photocells Make sure the E Link displays No cow and No Tag for both ID1 and ID2 8 10 INTENTIONALLY BLANK innovators in agriculture D 1022 1004EN Test and Adjustment D 1022 1004EN innovators in agriculture 9 TROUBLESHOOTING 9 1 Troubleshooting Table The auger is blocked Test the auger page 8 7 probably due to dirty or If the auger motor does not ru
42. rts and push button e 3 Select Last visit and push button acl List Details about Cows with low Consumption 1 Get the E Link Manual Controller 6 2 2 Inthe main menu select Reports and push button 1 3 Select Low consumption and push button 1 List Details per Group about the last 24 Hours 1 Get the E Link Manual Controller 6 2 2 Inthe main menu select Reports and push button 41 3 Select Group 24 hr report and push button 1 4 Select the group to report about and push button al List Attentions 1 Getthe E Link Manual Controller page 6 2 2 Inthe main menu select Reports and push button et 3 Select Attentions and push button eli Operating Instructions 6 3 6 4 INTENTIONALLY BLANK innovators in agriculture D 1022 1004EN Operating Instructions innovators in agriculture 7 MAINTENANCE This section will be included at a later date D 1022 1004EN Maintenance 7 1 7 2 INTENTIONALLY BLANK innovators in agriculture D 1022 1004EN Maintenance D 1022 1004EN innovators in agriculture 8 TEST AND ADJUSTMENT 8 1 Introduction This chapter contains the following test and adjustment procedures for the COSMIX Mobile Concentrate Feeder Display the software version Adjust the COSMIX M Make basic software settings Make feeding settings Test the operation of
43. tification valid for two years e Product Specialist certification valid for one year Master Product Specialist certification valid for one year During training a trainee is permitted to work for up to a maximum of six months under close supervision of a certified technician A trainee can do work on the milking robot can only in the presence of a certified technician When the training program is completed successfully Lely issue a certificate and a service pass to the technician The service pass contains the following information e The name of the technician e A photograph of the technician e Thecertification number of the technician e The date of expiry of the certification Contact Number Local Service Provider We suggest you write the telephone number and email address of your local service provider contact in the table below This makes sure you can easily find the information INTENTIONALLY BLANK innovators in agriculture D 1022 1004EN D 1022 1004EN 1 2 Safety Table of Contents Introduction 2 1 Introduction 2 2 Signal Words 2 3 Safety Instructions 2 3 1 General Safety 2 3 2 Electrical Safety 2 3 3 Installation Safety 2 3 4 Operating Safety 2 3 5 Maintenance Safety 2 4 Safety Decals 2 4 1 Safety Decal Messages 2 4 2 Position of the Safety Decals 2 4 8 Maintenance of Safety Decals 2 4 4 Installation of Safety Decals Specifications 3 1 Dimensions and Weight 3 2 Batter
44. up 1 8 e Dose per day page 8 5 e Maximum credit page 8 6 e Entrance credit page 8 6 Dose per day For each group a dose per day must be set 0 999 gr 0 2 2 Ib This setting applies to all cows in the group The dose per day is released step by step and added to the feed credit of each cow individually Maximum credit If a cow does not consume her feed credit during a day the rest is added to the credit for the following day up to a maximum The maximum credit must be set per group Entrance credit The COSMIX M only supplies feed when the feed credit for a cow is more than the the entrance credit The reason for this is to discourage cows to visit the COSMIX M too often Properly set feed settings make sure that each cow can eat her feed dose whenever she wants The entrance credit limits the number of visits and thus the accessibility for non dominant cows Description and Operation 4 11 4 3 2 4 3 3 Working Reports innovators in agriculture The submenu is also used to Move cows to another group page 8 6 e Remove cows from the database page 8 7 e Seta cow name page 8 7 Cows that did not visit the COSMIX M before and that are identified as a new cow with the correct identification are added to group 8 Therefore they are fed according to the Feed settings of group 8 You can move the cow to another group if needed Cows that are no in the herd can be rem
45. ust the Detection Distance from the Photoelectric Sensors 8 4 Make Basic Software Settings 8 4 1 Adjust the Refill Level of the Feed Bin 8 4 2 Calibrate the Load Cell Sensors 8 4 3 Set the Weighing Unit ON or OFF 8 4 4 Set the Antennas 8 4 5 Set the Portion Size 8 4 6 Set the Time 8 4 7 Setthe Display Language 8 5 Feeding Settings 8 5 1 Set the Feed Dose per Day 8 5 2 Set the Maximum Credit 8 5 3 Set the Entrance Credit 8 5 4 Move a Cow to another Group 8 5 5 Remove a Cow from the Database 8 5 06 Seta Cow Name 8 6 Test the Operation of the COSMIX M 8 6 1 Test Auger Motors 5 1 5 1 5 1 5 1 5 1 5 2 5 2 5 2 5 3 5 6 6 1 6 1 6 1 6 2 6 2 6 3 6 3 6 3 6 3 6 3 7 1 8 1 8 1 8 1 8 1 8 1 8 1 8 2 8 2 8 3 8 3 8 4 8 4 8 5 8 5 8 5 8 5 8 6 8 6 8 6 8 7 8 7 8 7 8 7 uy innovators in agriculture D 1022 1004EN D 1022 1004EN 8 6 2 Test the Load Cell Sensors 8 6 3 Test the Photoelectric Sensors 8 6 4 Test the ID Sensors 9 Troubleshooting 9 1 Troubleshooting Table 9 2 Recovery Procedures 9 2 1 Clean the Auger 9 2 2 Reset the Solar Charge Controller 10 Diagrams 10 1 Dimensions of the COSMIX M 10 2 Cow Dimensions 10 3 Connection Diagram Glossary of Terms Index 8 8 8 8 8 8 9 1 9 1 9 1 9 1 9 3 10 1 10 1 10 2 10 3 uy innovators in agriculture xiii xiv INTENTIONALLY BLANK innovators in agriculture D 1022 1004EN D
Download Pdf Manuals
Related Search