User Manual - SVT Innovations
Contents
1. SVT IP Video Intercom System A B User Manual Please read this user manual prior to installing the system and keep it well for future use Quick Start Guide 1 INSTALLATION Install outdoor station on the wall as shown below and then wire it up Back case Screws Plastic wall plug System Wiring Rain Cover 2 CONTROLCAM SETUP Android users can download ControlCam App from Google Play while iOS users can download it from iOS App Store Complete the installation in your smart phone or tablet ANDROID APP ON 4 Available on the gt Google play App Store Tip Both download and usage for users are free Please make sure the outdoor station in the range of your network Please keep your app be the latest version App herein subject to change without prior notice site 3 NOMENCLATURE Front View Rear View k LED Light e Camera RJ45 Door bell Name Plate 8 Call Button Ethernet Cable ER Exit Button Antenna N oar Power Supply Keypad GIG Electric Door Lock Microphone Front View Rear View jess RJ45 D bell Name Plate e Call Button Ethernet Cable oor De n ISE Exit Butt Antenna SERE xit Button Power Supply Electric Door Lock Microphone Settings Instruction There are two ways to connect the outdoor station to router 1 WiFi wireless connection Please kindly noted that ControlCam2. if it s not found please try it again Note Verify that your smart phone or tablet can receive the strong WiFi signal Step 6 Click the device to be configured and click Start configuring nce Step 7 Set WiFi information Input the WiFi password and wait 100 seconds Step 8 It will show Configuration is successful please add the device to the phone then click OK to confirm Step 9 Input the default User Name admin and Password 1234 click OK to confirm Step 10 Click OK the device is added successfully Step 11 Back to the device list and click ontheright top corner of the device Click ON in Outdoor call in option and return to the main interface 2 2 RJ45 ETHERNET CABLE CONNECTION If you want to connect the outdoor station with RJ45 Ethernet cable for longer distance please follow the below steps Note make sure the outdoor station is already connected to your smart phone by WiFi Don t remove the antenna during below settings Step 1 Login you router setting page to find the IP address of the outdoor unit Step2 Enter the above IP address by Internet Explorer to IP Camera login page Login with default User Name admin Password 1234 Same password as the one in ControlCam application username on Step 3 Click Config Network Settings LAN Set IP and Gateway as the same segment as your LAN network for example if your LAN n
3. press for 7 times after 3 seconds another long Di sound will be heard it indicates deleting successfully The unlock time changes to 1 second and the programming password does not change 3 Press to exit the programming mode 10 Restore factory mode Switch off the power press and hold switch on the power After a long Di sound is heard then release restoring successfully the system restore factory programming password 1234 and clear our all the set passwords 10 The design and specifications of this user manual can be changed without any notification to the user All copyright and interpretation rights are reserved to SVT Innovations Inc
4. etwork gateway is 192 168 0 1 set IP to the same segment as LAN network gateway here set as the same as the found WiFi IP address 192 168 0 88 IP CAMERA LAN Setting DHCP Enable IP 192 168 0 88 Subnet Mask loss 255 255 0 Gateway 192 168 O 1 Preferred DNS lay 114 114 114 Alternate DNS a a mac g i Step 4 After completing the above settings connect your outdoor station with the Ethernet cable to the router You can remove the antenna Then the setting is OK Note On the page of IP camera configuration you can do many advanced settings For example you can set the date and time by clicking Config System System time You can activate motion detection function by clicking Config Alarm Setting Motion Detection Enable Please note most settings need professional network knowledge Please do not do any setting if you are not sure about 3 How to add more smart phones or tablets to the network outdoor station Step 1 Open the ControlCam App onthe smart phone or tablet Step 2 Click Enter Now Step 3 Click Add a Network Device There are three ways to add the network outdoor station a LAN Search Click LAN Search then click the found device input the default User Name and Password Click OK the device is added successfully b QR Code Scan Click QR Code Scan input the default User Name and Password Click OK the outdoor stati
5. ht top corner click OFF for outdoor Call in option Step2 click unlock password setting Step3 Input old password and new password Step4 click Setting to finish setting Shown as the photo at the right side How to set user passwords on outdoor station The below instruction is for outdoor station with keypad only The original factory default programming password is 1234 not access code In the programming mode 40 groups of 4 digit passwords can be set to unlock door lock 2 Modify the programming password 1 Switch off the power press button and hold switch on the power After a continuous sound Di is heard release button 2 The continuous sound stops then enter 4 digits can be set as 2 6 digits new programming password the length same as original code another long Di sound is heard it indicates modifying successfully 3 Press xtoexitthe programming mode 3 Enter the programming mode 1 Press x a Di sound is heard enter the 4 digits can be set as 2 6 digits programming password along Di sound can be heard It indicates entering the programming mode successfully 2 Within 30 seconds without any operation it will exit the programming mode or press to exit 4 Set unlock time Factory default setting is 1 second 1 Enter the programming mode 2 Press 00 along Di sound is heard enter 2 digits from 01 99 as the unlock time another long D
6. i sound can be heard it indicates setting successfully 3 Press to exit the programming mode 8 5 Add user passwords 1 Enter the programming mode 2 Enter 2 digits from 01 40 the digits 31 40 are for normal open or normal close these digits are not allowed to set the unlocking time along Di sound is heard Press 4 digits can be 2 6 digits password another long Di sound can be heard it indicates adding successfully 4 Press to exit the programming mode 3 6 Delete user passwords 1 Enter the programming mode 2 Enter 2 digits from 01 40 along Di sound is heard press x to confirm another long Di sound can be heard it indicates deleting successfully 3 Press to exit the programming mode 7 Delete user passwords directly 1 Enter the programming mode 2 Press when DiDi sound is heard enter that 4 digits can be set as 2 6 digits password you want to delete along Disound can be heard it indicates deleting successfully 3 Press to exit the programming mode 8 Setting the length of password 1 Enter the programming mode 2 Press 99 along Di sound is heard then enter 2 6 digits another long Di sound can be heard it indicates setting successfully 3 Press to exit the programming mode 9 Delete all settings 1 Enter the programming mode 2 Press when a DiDi sound is heard press again along Di Sound can be heard then
7. on is added successfully c Manually Input Click Manually Input input the outdoor station GID the default User Name and Password Click OK the device is added successfully Step 4 Click e onthe right top corner Step 5 Click ON in Outdoor call in option and return to the main interface Note 1 Each outdoor station has a unique GID 2 The default user name is admin 3 The default password is 1234 User Guide 1 Talking When the visitor calls the device will receive the ring alert The user canclick Accept or decline on the pop up call alert Press and hold amp to start talking and release to listen 2 Unlocking Input unlock password while talking or monitoring Same as the user name password a Monitoring Click the image on the main interface to monitor the outside environment If you want to talk with the visitor and hear the sound click the icon and on the screen to start talking Image Capture Click the icon to capture an image Video Recording Click the icon to start video recording and then click the icon to end it How to detele the device Step 1 Click eee onthe right top corner of the device Step 2 Click OFF in Outdoor call in option Step 3 Click Edit Step 4 Click Delete Step 5 Click OK to delete the device Change unlock passwords poo e Step 1 Click eee onthe rig
8. works with the 2 4Ghz network 2 RJ45 Ethernet cable connection 1 How to set factory default Ifthe outdoor station is connected to a new WiFi router you need to set the outdoor station to factory default status first Step 1 Cut off the power Step 2 Power on again Step 3 Hold the calling button for around 45 seconds until the LED light flash and a Bi sound will be heard 2 2 1 WIFI WIRELESS CONNECTION a For iPhone or iPad Step 1 Connect the WiFi from the outdoor station in the WiFi list on iPhone or iPad choose the WiFi name like LIDxXxxxxxxx Step 2 Open the ControlCam App Step 3 Click Add a Device Step 4 Click Add a New Device Step 5 Click Start configuring Step 6 Click the outdoor station to be configured and click Start configuring Step 7 Choose the WiFi from your own router input its WiFi password click setting Step 8 Input the default User Name admin and Password 1234 click OK to confirm Step 9 Back to the device list and click ontheright top corner of the device Click ON in Outdoor call in option and return to the main interface Devices Johnson e Miranda b For Android Step 1 Open the ControlCam App on the smart phone or tablet Step 2 Click Enter Now Step 3 Click Add a Device Step 4 Click Add a New Device Step 5 It will show Searching and then find the device
Download Pdf Manuals
Related Search