USER`S MANUAL
Contents
1. 4 INSTALLATION A Installing on the concrete wall 4 1 1 Removed the mounting plate Unclamping the fixed screws on the back of main body to removed the mounting plate MOUNTING PLATE N PLASTIC PARTS P xa 4 1 2 Fix the bolts in the proper position Decide the position with the mounting plate and pour cement into the bolt holes CONCRETE 13 15mm 4 1 3 When the cement has concreted fit the mounting plate use the washer and nut according to the following WASHER SPRING WASHER NUT MOUNTING PIATE 4 1 4 Install the main body Set the main body onto the upper end of the mounting plate and clamp it as shown B Installing on the wooden wall 4 2 1 Fix the mounting plate in the proper positions with tapping screw MOODEN SCREW MOUNTING ee 4 2 2 Same as the step 4 of A C Hanging from the ceiling 4 3 1 Remove the mounting plate from main body Same as step 4 1 1 t d a FIXING SCREW 4 3 3 Set the mounting plate on the ceiling brackets and ensure safety amp fixing use the bolts attached to the ceiling brackets as Fig Using the ceiling brackets to hang from the ceiling the position of mounting plate can be adjusted in the limit of 100mm WASHER SPRING WASHER2. a NUT H H MAX100mm MOUNTING PIATE 4 3 2 Fixing ceiling brackets as Fig T WASHER a SPRING WASHER 7 Y NUT 4 3 4 Do the same as step 4 of A to install the main body D For above ceiling 4 4 1Fix the air curtain as in the procedure for installing on the concrete wall 4 4 2 Then install the pipes as right Fig Instruction WIND PIPING IN EEE f OUT t bere ae r 7 c umgy 1 7 5 TECHNICAL PARAMETER Diam i i i i MODEL a A Ee cian i aad Seam ee ae wal a mm H L H L H L H L i ACS 36i 2 160 110 57 55 1150 900 11 900x180x215 ACS 48i 2 115 220 50 60 200 150 11 9 58 56 1750 1200 13 5 1200x180x215 ACS 60i 2 230 180 59 57 2180 1500 15 1500x180x215 6 ELECTRIC WORK BLUE BROWN RED YELLOW RECEIVER lt RECEIVER J ORANGE I C 7 1 0 j C YELLOW BLACK WHITE YELLOW GREEN THERMAL CUT OUT f DOUBLE SPEED INFRARED REMOTE CONTROLLED WIRING DIAGRAM 7 OPERATION 7 1 Turn on the power switch 7 2 Select the best speed High H Low L 7 3 According to the installation place to adjust the direction vane to obtain the best effect CAUTIONS Use the unit at the rated voltage and frequency indication on the nameplate Disconnect power source before un
3. innover USER S MANUAL AIR CURTAINS ACS36i 2 ACS48i 2 ACS60i 2 Thanks for purchase this Air Curtain please read these instructions carefully before use 1 PRODUCT INTRODUCTION As one of the new top class products for modern decoration air curtain is also matched with the air conditioner And it is installed at the entrances of supermarket theater meeting room hotel office room working shop and nocuous air and so on storeroom to prevent the dust mosquito and 2 IDENTIFICATION amp INSTALLATION DIMENSIONS MODEL A B C D F G H ACS 36i 2 900 240 ACS 48i 2 1200 42 90 105 180 215 ACS 60i 2 1500 840 3 INSTALLATION CAUTION Must follow below when installing air curtain 3 1Please install the unit in a sturdy place to avoid the shaking and ensure its security because it maybe causes the wall becoming flexible or shaking and noise e XANA S EREE opopona ponanono 0 0 0 0 kodot UOUOUOUO NENENENEN TERE 3 2 Please install the unit inside the room INDOOR OUTDOOR OUT 3
4. 3 Don t install the unit too low no less than 2 3 meters from the ground opopona yoyay ona l m 0 m QUOUOUO OUOUOUO 3m a 3 4 When the entrance is wider than the unit it is recommended to install two or more units in parallel In this case provide 10 40mm gaps between the units 4 1 0 40mm 3 5 Don t allow gaps between the unit and the wall When hanging it from the ceiling using the enclosed ceiling brackets E er 3 6 Don t install the unit in a place where it is splashed by water exposed to excessive steam explosive gas or corrosive gas Ono Oo nononono M l m OUOUOUO Uovoloto
5. it operation Routing maintenance must be done every year Never use petrol benzene thinner or any other such chemical for clearing the unit Don t allow water or anything enters the motor f When power supply comes from socket the plug must accord with IEC335 1 When the power cord is connected with charging line directly all polarity switches that the contact gap is 3mm at least must be installed in the charging line g In order to avoid any injury must change the line of air curtain by professional worker or factory when the line has trouble 0OQA0c 0
Download Pdf Manuals
Related Search