USER MANUAL - TempSen Europe BV
Contents
1. Start please press and hold Start Stop button for 5 seconds to start device under manual start LCD status would vary depending on different start options you selected Start Delay LCD displays countdown on basis of minutes In this example there are 60 minutes from starting recording Vv e Temperature Start LCD displays w or a depending on the type of temperature start triggering mechanisms you selected and current temperature readings USER MANUAL TEMPOD M 14 0623 PAGE6 13 TEMPSEN In this example logger configured as temperature start shows current temperature reading after manual start If device is set as Auto Start no further action is required to start device logger would start recording automatically when time is up gt TempodM1 Please press and hold Start Stop button for 5 seconds to start device OK and ALARM LEDs flash in turn for 3 times indicating start success IMPORTANT To avoid unnecessary loss to your goods please do not use the temperature logger while the LEDs do not flash after being started In Recording Recording Tempod MP MP X MP 1 Tempod M1 OK or Alarm LED flashes Ambient temperature gt 0 C E every 10 seconds WES OK or Alarm LED flashes 20 C lt Ambient temperature lt 0 C E v A diamond flashing in left display 4 Indicates currently recording Ambient temperature lt 20 C OK or Alarm LED flashes every 30 seconds Mark Important Events 32. FORM SERVICE ON THIS HARDWARE PRODUCT TempSen Electronics Company T 86 216768 5210 F 86 216768 5232 E info tempsen com www tempsen com Technical Support support tempsen com USER MANUAL TEMPOD M 14 0623 PAGE13 13
3. TEMPSEN USER MANUAL 14 0623 REV D gt Tempod MP gt Tempod MP X gt Tempod MP 1 gt Tempod M1 2014 TEMPSEN ELECTRONICS COMPANY WWW TEMPSEN COM TEMPSEN Contents Product Ove nie Wien iaa A das 3 TempCentre SOMW ANC id a A AA ai 4 How to download TempCentre Software oocccncccninccinocinoncccnoncncnnnn non nnnnnn cnn ncn ranas 4 Configure Data LOGG isvvnnciisc EE E E dana iones 4 Trip Description ees 4 Start Mode sad is 4 gt MandalSarticcosio iii od ei dd add dd 4 gt PUTO o COOP A TN 5 Alarm Setting S rin dd ei de 5 gt AlaimModS ct ta 5 gt A ON 5 E Co vekdenstuanesatntia A aa aaa Eaa a doaa aaa a a aaea 6 gt PDF Report ConfiguratiON cion ia 6 Start RECON iii 6 gt Tempod MP MP X MP 1 cecccccceeeeneeeeeeeecaeeeeaaeeeneeeeaeeeeaaeeseaeeseeeeeseaeeesaaeeseeeeseeeeseaeeseaeeeeaes 6 gt Tempod MMos a ea a id 7 In REGONGING siiri inae aa a i a aaa a anid ee miei ae 7 Mane Imponant Evne ers a T T E s 7 gt Tempod MP MP X MP 1 oooccconnccccccccconoccconcconnc anna 7 gt NSM POG MA escorial dedos 8 Trim Data using Mark PONS iniinda ti dade didnt aid Eda iaaa 8 Alar CONO art ita 8 Review Temperature Statistics oonnocinnnidinnnnnnnnnnnconnnccnocccnn cnn nc 9 gt Tempod MP MP X MP social catala iii redadas 9 Stop RecordiNia idear da did aa 10 Download Data ccoo ii 10 gt Download data via TempCentre oooncccnnnicinnncnnncconnccccncnnn aran cnn cnc 10 gt Get data by copying PDF
4. Tempod MP MP X MP 1 During recording press and hold Select Mark button for several seconds display will change to Mark mode and a MARK flashes in upper display indicating a mark is about to be placed To successfully add a mark please hold the Select Mark button throughout the whole process A maximum of 9 marks are available for adding USER MANUAL TEMPOD M 14 0623 PAGE 13 TEMPSEN Before After A timestamp would be written in logger every time you add a mark all marks added would be plotted in graph and data list in report gt Tempod M1 During recording press and hold Mark button for 3 seconds both OK and ALARM LEDs lighting up and off indicates mark success A timestamp would be written in logger every time you add a mark marks would be plotted in graph and data list area in report Trim Data using Mark points TempCentre software allows user to trim each data record using mark points placed during recording that means by taking advantage of placing mark points in transit user could obtain a data record that makes sense for stakeholders NOTE Only TempCentre not lower than version 1 3 3 supports Data Trim Alarm Condition Alarm in recording Tempod MP MP X MP 1 Tempod M1 No Alarm Triggered OK LED flashes Atick appears in left display with the middle diamond flashing during recording USER MANUAL TEMPOD M 14 0623 PAGES 13 TEMPSEN om Alarm Triggered ALARM LED flashes i
5. again after your successful registration last time please click I already signed up download now button in dialogue then software would begin to download via your internet browser in couple of minutes Configure Data Logger Connect logger to USB port of PC open TempCentre software click Connect to establish connection with PC then move to Configure Device to start configuration Connecting to PC Tempod MP MP X MP 1 Tempod M1 PE Both OK and ALARM LED light up Trip Description A brief remark for describing recording task and shows in data report Start Mode Manual Start If selected manual start device needs to be started by pressing Start Stop button and 2 additional options available in this mode gt Start Delay After started manually the time span device needs to wait to start recording USER MANUAL TEMPOD M 14 0623 PAGE4 13 TEMPSEN gt Temperature Start After started manually the temperature condition device needs to meet to start recording there are 3 temperature start types available for users to choose 1 Over device would start recording when temperature over the temperature value preset 2 Under device would start recording when temperature under the temperature value preset 3 Between device would start recording when temperature falls between the temperature range preset Auto Start Allows device to start recording on the specific date time configured by user logger would st
6. are is not covered under this Limited Warranty Refer to the licensing agreement accompanying the software for details of your rights with respect to its use TempSen does not warrant that the operation of product will be uninterrupted or error free TempSen is not responsible for the damage arising from failure to follow instructions relating to the product s use This warranty does not apply a to consumable parts such as batteries unless damage has occurred due to a defect in materials or workmanship b to cosmetic damage including but not limited to scratches dents and broken plastic on ports c to damage caused USER MANUAL TEMPOD M 14 0623 PAGE12 13 TEMPSEN with non TempSen products d to damage caused by accident abuse misuse flood fire earthquake or other external causes e to damage caused by operating the product outside the permitted or intended uses described by TempSen f to damage caused by service including upgrades and expansions performed by anyone who is not a representative of TempSen or TempSen Authorized Service Provider g to a product or part that has been modified to alter functionality or capability without the written permission of TempSen or h if any TempSen serial number has been removed or defaced IMPORTANT DO NOT OPEN THE HARDWARE PRODUCT OPENING THE HARDWARE PRODUCT MAY CAUSE DAMAGE THAT IS NOT COVERED BY THIS WARRANTY ONLY TEMPSEN OR AN AUTHORIZED SERVICE PROVIDER SHOULD PER
7. art recording automatically when time is up no need to press Start Stop button after configuration Alarm Settings gt Alarm Mode gt No alarm setting gt High amp Low alarm gt Multiple Alarm ranges 5 alarm ranges available Tempod M1 does not support multiple alarm ranges 3 Alarm Type Single Event Single event is that alarm could only be triggered when temperature over blow alarm limit for a continuous period of time is not less than alarm delay gt Cumulative Alarm Cumulative alarm means alarm could be triggered once the cumulative total time temperature over or under alarm limit is not less than alarm delay NOTE Only Tempod MP Tempod MP X of firmware version number not less than X1 6 support temperature start capability Click Write Configuration button in down right corner of program to write in configuration parameters USER MANUAL TEMPOD M 14 0623 PAGES 13 TEMPSEN Advanced Settings gt PDF Report Configuration Set up time zone and daylight saving time for PDF report created by loggers NOTE Oo This function only applies to models able to generate PDF report automatically Start Recording gt Tempod MP MP X MP 1 LCD Status after configuration Standby for manual start press button to start E a miia dal Standby for manual start press button to start if configured with Temperature Start Standby for timer start auto start If device is set as Manual
8. ective parts with new or refurbished user installable parts that TempSen provides in fulfillment of its warranty obligation A replacement product or parts including a user installable part that has been installed in accordance with instructions provided by TempSen assumes the remaining warranty of the original product or ninety 90 days from the date of replacement or repair whichever provides longer coverage for you When a product or part is exchanged any replacement item becomes your property and the replaced item becomes TempSen s property Parts provided by TempSen in fulfillment it s warranty obligation must be used in products for which warranty service is claimed When a refund is given the product for which the refund is provided must be returned to TempSen and becomes TempSen s property EXCLUSIONS AND LIMITATIONS This Limited Warranty applies only to the hardware product manufactured by or for TempSen that can be identified by the TempSen trademark trade name or logo affixed to it The Limited Warranty does not apply to any non TempSen hardware product or any software even if packaged or sold with the TempSen hardware Manufacturers suppliers publishers other than TempSen may provide their own warranties to the end user purchaser but TempSen in so far as permitted by law provides their products as is Software distributed by TempSen with or without the TempSen brand name including but not limited to system softw
9. ll start generating PDF report and it may take couple of seconds for the process to complete LCD displays as below while creating PDF report Open a storage device named TempSenDisk in Computer copy the PDF report inside to your PC and then open and view it with Adobe PDF reader NOTE Logger would be ready for communication with TempCentre software only after PDF report is completely created USER MANUAL TEMPOD M 14 0623 PAGE10 13 TEMPSEN Battery How to install or change battery Insert a coin in the groove on battery cover to spin it in the direction of OPEN to open the cover place a new CR2450 lithium battery in battery compartment with positive electrode toward outside after changing battery put the cover back on the battery compartment and make sure the 2 triangles hare directed at each other then spin it back in the direction of CLOSE to lock the battery cover IMPORTANT To make sure logger functions as expected please contact us for CR2450 battery used for Tempod M series Low Battery Indicator 3 Tempod MP MP X MP 1 A Battery Low icon appears in the upper left corner of display indicates current battery is going to run out soon Please replace the battery as soon as possible IMPORTANT If you take battery out of logger after configuring logger please do remember to re configure data logger when you want to start recording or the date time recorded will be incorrect NOTE We sugge
10. nstead of OK LED Across appears in left display with the middle diamond flashing during recording There will be no alarm status icon tick or cross if logger was set without alarm thresholds Review Temperature Statistics gt Tempod MP MP X MP 1 Single click Select Mark button to review logging statistics step by step oy Wy NY e As Highest Temperature Lowest Temperature Average Temperature Mark History In this case 6 marks have been placed USER MANUAL TEMPOD M 14 0623 PAGES 13 TEMPSEN Stop Recording After arriving at destination press Start Stop button and hold for 5 seconds to stop recording Recording Stopped Tempod MP MP X MP 1 Tempod M1 e Both OK and ALARM LEDs repeat lighting up SA and off for 3 times when manually stopped e OK or ALARM LED flashes 2 times every 10 A stop shows in LCD seconds after stopped Download Data gt Download data via TempCentre Connect logger to PC open TempCentre software and click Connect to establish data connection between logger and PC after successful connection all raw data in data logger would be loaded to TempCentre for viewing and analysis Please remember to save data to data base of TempCentre by clicking Save button in down right corner of program 3 Get data by copying PDF report For models supporting automatic PDF report generation there is an easier way to achieve data connect logger to USB port of PC data logger wi
11. repoti ie st td tibia 10 Battery ana A A na ea aaah 11 How to install or change battery cccccecececeeeeeeeee esas eeeeeeeeeeeeeeaeeeeaaeeeeeeeseaeeesaaeeseaaeseeeeeseeeesaeeseeeseeeees 11 Low Battery IMGicators cs sac caieces seaeseehcccketsienctsvete fenced sane a dd Diane cota clara 11 gt Tempod MP MP X MP2T ecccicicccii ii iaa 11 Additional Information ici Ro A bien BAe Abe aa a aa era aadar aaie 12 WTA A AS errr terre eee A eee errr 12 USER MANUAL TEMPOD M 14 0623 PAGE2 13 TEMPSEN Product Overview Battery cover 5 alar ok O 3 2 Device Front Device Front Tempod MP MP X MP 1 Tempod M1 UU Device Rare 1 USB plug 2 Start and Stop button 3 Select and Mark button 4 LCD 5 LED 6 Tempod M1 is equipped with LED and without Select button NOTE Only Tempod MP X is equipped with fixed external NTC probe 1 meter USER MANUAL TEMPOD M 14 0623 PAGE3 13 TEMPSEN TempCentre Software Please download and install the latest version of TempCentre software from www tempsen com How to download TempCentre software e f it s your first time to download software from www tempsen com please sign up with the information required at first then an email containing download link would be sent to the mail address you left in couple of minutes f you want to download the software from www tempsen com
12. st you put the battery out of logger to decrease power consumption when the logger will be idle for a long period of time Time Error Time recording deviation of Tempod logger is 2 minutes every month USER MANUAL TEMPOD M 14 0623 PAGE 13 TEMPSEN Additional Information e To avoid damaging your Tempod logger please do not disconnect it from USB port while it is communicating with the computer e Data stored in Tempod logger is retrievable even battery runs out e Tempod logger uses CR2450 lithium battery please do not heat microwave or recharge it Please contact your retailer for replacement Please follow local regulations when recycling or disposing of Tempod logger Warranty TempSen warrants this TempSen branded hardware product against defects in materials and workmanship under normal use for a period of ONE 1 YEAR from the date of retail purchase by the original end user purchaser Warranty Period If a hardware defect arises and a valid claim within the Warranty Period as its option and to the extent permitted by law TempSen will either 1 repair the hardware defect at no charge using new parts or parts equivalent to new in performance and reliability 2 exchange the new product with a product is new or equivalent to new in performance and reliability and is at least functionally equivalent to the original product or 3 refund the purchase price of this product TempSen may request that you replace def
Download Pdf Manuals
Related Search