user manual Dishwasher - Pdfstream.manualsonline.com
Contents
1. Quick 0 8 8 Eco 05109 12 13 Glass 0 6 0 7 11 12 1 The digital display shows the programme duration The pressure and temperature of the and the quantity of dishes can change water the variations of power supply these values Care and cleaning Cleaning the filters 3 Turn the handle about 1 4 a turn anti The filters must be checked and cleaned clockwise and remove the filter system from time to time Dirty filters will degrade the washing result Warning Before cleaning the filters ensure that the machine is switched off 1 Open the door remove the lower basket 2 The dishwasher filter system comprises a coarse filter A a microfilter B anda flat filter Unlock the filter system using the handle on the microfilter 4 Take hold of the coarse filter A by the handle with the hole and remove from the microfilter B 5 Clean all filters thoroughly under running water 6 Remove the flat filter from the base of the washing compartment and clean both faces thoroughly 18 electrolux 7 Put the flat filter back in the base of the washing compartment and ensure that it fits perfectly 8 Place the coarse filter A in the microfil ter B and press together 9 Put the filter combination in place and lock by turning the handle clockwise to the stop During this process ensure that the flat filter does not protrude above the base of the washing compartment NE2. ning programme e activation deactivation of the rinse aid dis penser ONLY with Multitab function ac tive e the end of a washing programme a zero will appear in the digital display e the countdown for the delay start e fault codes concerning malfunction of the dishwasher Function buttons The following functions can be set using these buttons e the adjustment of the water softener level e cancel a washing programme or a delay start in progress e activate deactivate the Multitab function e activate deactivate the rinse aid dispenser when the Multitab function is active Setting mode Press the On Off button if ALL programme button lights come on the appliance is in setting mode First use Before using your dishwasher for the first time e Ensure that the electrical and water con nections comply with the installation in structions e Remove all packaging from inside the ap pliance e Set the water softener level Set the water softener The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply which would have a detrimental or adverse effect on the operation of the appliance The higher the content of these minerals and salts the harder your water is Water hard ness is measured in equivalent scales Ger man degrees dH French degrees TH and mmol l millimol per litre international unit for the hardness of water Water
3. purposes Detergent residue may still be present in your machine e Ensure that the door of the dishwasher is always closed when it is not being loaded or unloaded In this way you will avoid any body tripping over the open door and hurt ing themselves e Do not sit or stand on the open door Child safety e This appliance is designed to be operated by adults Children must be supervised to ensure that they do not play with the ap pliance e Keep all packaging well away from chil dren There is a risk of suffocation e Keep all detergents in a safe place out of children s reach e Keep children well away from the dish washer when the door is open Installation e Check your dishwasher for any transport damage Never connect a damaged ma electrolux 3 chine If your dishwasher is damaged con tact your supplier All packaging must be removed before use Any electrical and plumbing work required to install this appliance must be carried out by a qualified and competent person For safety reasons it is dangerous to alter the specifications or attempt to modify this product in any way Never use the dishwasher if the electrical supply cable and water hoses are dam aged or if the control panel work top or plinth area are damaged such that the in side of the appliance is freely accessible Contact your local Service Force centre in order to avoid hazard All sides of the dishwasher must never be drilled
4. 5 1 6 4 23 28 40 50 4 0 5 0 19 22 sis GH She CL 15 18 26 32 2 6 3 2 11 14 19 25 1895255 4 10 7 18 O 1e gal am lt 07 Setting manually i The dishwasher is factory set at position 2 Open the dishwasher door Remove the lower basket from the dish washer Turn the water hardness dial to position 1 or 2 see chart 4 Replace the lower basket M IN Setting electronically i The dishwasher is factory set at level 5 1 Press the On Off button The dishwasher must be in setting mode Use of dishwasher salt A Warning Only use salt specifically designed for use in dishwashers All other types of salt not spe cifically designed for use in a dishwasher es pecially table salt will damage the water soft ener Only fill with salt just before starting one of the complete washing programmes This will prevent any grains of salt or salty water which may have been spilt remaining on the bottom of the machine for any period of time which may cause corrosion Adjusting the water hardness setting electrolux 7 manually electronically 2 level 8 yes 2 level 7 yes 2 level 6 yes 2 level 5 yes 1 level 4 yes 1 level 3 yes jl level 2 yes 1 level 1 no 2 Simultaneously press and hold function buttons B and C until the lights of func tion buttons A B and C start flashing 3 Press function button A the lights of function buttons B and C go off while the light of function but
5. aid suitable for dishwashers Unloading the dishwasher 16 Washing programmes 16 Care and cleaning 17 What to do if 18 Technical data 20 Hints for test institutes 20 Installation 21 Water connection 22 Electrical connection 24 Environment concerns 24 Subject to change without notice e Avoid opening the door whilst the appli ance is in operation hot steam may es cape e Do not take any dishes out of the dish washer before the end of the washing cy cle e After use isolate the appliance from the power supply and turn off the water sup ply e This product should be serviced only by an authorized service engineer and only gen uine spare parts should be used e Under no circumstances should you at tempt to repair the machine yourself Re pairs carried out by inexperienced persons could cause injury or serious malfunction ing Contact your local Service Force Cen tre Always insist on genuine spare parts General safety e Persons including children with reduced physical sensory mental capabilities or lack of experience and knowledge must not use the appliance They must have su pervision or instruction for the operation of the appliance by a person responsible for their safety e Dishwasher detergents can cause chemi cal burns to eyes mouth and throat Could endanger life Comply with the safety in structions of the dishwasher detergent manufacturer e Water in the dishwasher is not for drinking
6. copper items Lead crystal glass Steel items prone to rusting Wooden platters Items made from synthetics fibres e Only wash stoneware in the dishwasher if it is specially marked as being dishwasher safe by the manufacturer Glazed patterns may fade if machine washed frequently Silver and aluminium parts have a tendency to discolour during washing Residues e g egg white egg yolk and mustard often cause dis colouring and staining on silver Therefore al ways Clean left overs from silver immediately if it is not to be washed straight after use 10 electrolux Load cutlery and dishes The lower basket The lower basket is designed to take sauce pan lids plates salad bowls cutlery ect Service dishes and large lids should be ar ranged around the edge of the basket en suring that the spray arms can turn freely The rows of prongs in the lower basket can lie flat to allow you to load pots pans and bowls l AA Ke THT IT T The cutlery basket Long bladed knives stored in an upright position are a potential hazard Long and or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket Take care when loading or unloading sharp items such as knives Forks and spoons should be placed in the removable cutlery basket with the handles facing downwards and the knives with their
7. e Fill with dishwasher detergent e Select a wash programme suitable for the cutlery and dishes e Start the wash programme Helpful hints and tips Sponges household cloths and any object that can absorb water may not be washed in the dishwasher e Before loading the dishes you should Remove all left over food and debris Soften remnants of burnt food in pans e When loading the dishes and cutlery please note Dishes and cutlery must not impede the rotation of the spray arms electrolux 9 Load hollow items such as cups glasses pans etc with the opening downwards so that water cannot collect in the container or a deep base Dishes and items of cutlery must not lie inside one another or cover each other To avoid damage to glasses they must not touch Lay small objects in the cutlery basket e Plastic items and pans with non stick coat ings have a tendency to retain water drops these items will not dry as well as porcelain and steel items e Light items plastic bowls etc must be loaded in the upper basket and arranged so they do not move For washing in the dishwasher the following cutlery and dishes are not suitable are of limited suitability Cutlery with wooden horn china or mother of pearls handles e Plastic items that are not heat resistant e Older cutlery with glued parts that are not tem perature resistant Bonded cutlery items or dishes Pewter or
8. handles facing upwards If the handles protrude from the bottom of the basket obstructing the lower spray arm load the cutlery with the handles facing upwards Mix spoons with other cutlery to prevent them from sticking together To make loading of the cutlery basket easier lower the cutlery basket handle For best results we recommend that you use the cutlery grid If the size and dimensions of the cutlery do not allow the use of the grid it can be easily hidden The upper basket The upper basket is designed for plates des sert plates saucers dinner plates of up to 24 cm in diameter salad bowls cups and glasses Arrange items on and underneath the cup racks so that water can reach all surfaces electrolux 11 Glasses with long stems can be placed up side down in the cup racks For taller items the cup racks can be folded upwards Mini cutlery basket The upper basket is supplied with a mini cut lery basket Caution NEVER PUT KNIVES IN THE MINI CUTLERY BASKET THIS WILL PREVENT DAMAGE TO THE APPLIANCE Place the mini cutlery basket in the front part of the upper basket only on the left hand side 12 electrolux The dimensions of the cutlery depend on the position of the upper basket Refer to the fol lowing table Cutlery dimensions for mini cutlery basket Upper basket in higher position maximum 15 cm Upper basket in lowe
9. lights for salt and rinse aid are deactivated When using the Multitab function the cycle durations may change If this is the case the running time for the programme is automat ically updated on the digital display i Activate deactivate the Multitab func tion before the start of a washing pro gramme Once the programme is running the Multitab function can NO longer be changed If you want to cancel the Mul titab function you have to cancel the programme setting and then deactivate the Multitab function In this case you have to set a washing programme and desired options again 4 Close the lid and press until it locks in place Detergent tablets from different manu facturers dissolve at different rates For this reason some detergent tablets do not attain their full cleaning power during short washing programmes Therefore please use long washing programmes when using detergent tablets to ensure the complete removal of detergent re siduals Activation deactivation of the Multitab function Simultaneously press and hold the two Mul titab buttons function buttons D and E until the Multitab indicator light comes on This means that the function is active To deactivate the function press the same buttons again until the indicator light corre sponding to the Multitab function symbol goes off i If the drying results are not satisfac tory we suggest that you 1 Fill up the rinse aid dis
10. water is running If the wa ter inlet hose starts to leak during this oper ation the safety valve cuts off the running water Please take care when installing the water inlet hose e The electrical cable for the safety valve is in the double walled water inlet hose Do not immerse the water inlet hose or the safety valve in water e f water inlet hose or the safety valve is damaged remove the mains plug imme diately e A water inlet hose with safety valve must only be replaced by the Service Force Centre Warning Dangerous voltage electrolux 23 Water drain connection The end of the drain hose can be connected in the following ways 1 To the sink outlet spigot securing it to the underside of the work surface This will prevent waste water from the sink run ning into the machine 2 To a stand pipe provided with venthole minimum internal diameter 4 cm The drain hose can face either to the right or left of the dishwasher Ensure the drain hose is not bent or squash ed as this could prevent or slow down the discharge of water The sink plug must not be in place when the machine is draining as this could cause the water to syphon back into the machine If you use a drain hose extension its internal diameter must be no smaller than the diam eter of the hose provided Likewise the internal diameter of the cou plings used for connections to the waste out let must be no smaller than the diameter
11. 0 00 102008
12. 1 pull the worktop from the back of the ma chine 2 and slide out the front slots lifting the worktop 3 Water connection Water inlet connection This appliance can be connected to either a hot max 60 or cold water supply With a hot water supply you can have a sig nificant reduction of energy consumption This however depends on how the hot water is produced We suggest alternative sources of energy that are more environmentally friendly as e g solar or photovoltaic panels and aeolian For making the connection itself the cou pling nut fitted to the appliance water inlet hose is designed to screw onto a 3 4 thread Insert the machine after adjusting the level ling with the adjustable feet When inserting the machine ensure that the water inlet and drain hoses are not kinked or squashed During all operations that involve accessibility to internal components the dishwasher has to be unplugged Be sure that once the appliance has been in stalled it is easily accessible for the service engineer in the event that a repair is required If the dishwasher is later used as a free standing appliance the original worktop must be re mounted The plinth on free standing appliances is not adjustable Levelling Good levelling is essential for correct closure and sealing of the door When the appliance is correctly levelled the door will not catch on either side of the cab inet lf the door does not
13. Thinking of yor_ user manual Electrolux Dishwasher ESF 46710 2 electrolux Electrolux Thinking of you Share more of our thinking at www electrolux com Contents Safety information Product description Control panel First use Set the water softener Use of dishwasher salt Use of rinse aid Daily use Load cutlery and dishes Use of detergent Multitab function NO O O1 B ND FE SR et Select and start a washing programme CE A Safety information i In the interest of your safety and to en k ol sure the correct use before installing and first using the appliance read this user manual carefully including its hints and warnings To avoid unnecessary mistakes and accidents it is important to ensure that all people using the appli ance are thoroughly familiar with its op eration and safety features Save these instructions and make sure that they re main with the appliance if it is moved or sold so that everyone using it through its life will be properly informed on appli ance use and safety Correct use This dishwasher is only intended for wash ing household utensils suitable for ma chine washing Do not put any solvents in the dishwasher This could cause an explosion Knives and other items with sharp points must be loaded in the cutlery basket with their points down or placed in a horizontal position in the upper basket Only use products detergent salt and rinse
14. VER use the dishwasher without filters Incorrect repositioning and fitting of the filters will produce poor washing results and will result in damage to the appliance i NEVER try to remove the spray arms If residues of soil have clogged the holes in the spray arms remove the debris with a cocktail stick External cleaning Clean the external surfaces of the machine and control panel with a damp soft cloth If necessary use only neutral detergents Never What to do if The dishwasher will not start or stops during operation Certain problems can be due to the lack of simple maintenance or oversights which can be solved with the help of the hints described in the chart without calling out an engineer use abrasive products scouring pads or sol vent acetone trichloroethylene etc Internal cleaning Ensure that the seals around the door the detergent and rinse aid dispensers are cleaned regularly with a damp cloth We recommend every 3 months you run the wash programme for heavy soiled dishes us ing detergent but without dishes Prolonged periods of non operation If you are not using the machine for a pro longed period of time you are advised to 1 Unplug the appliance and then turn off the water 2 Leave the door ajar to prevent the forma tion of any unpleasant smells 8 Leave the inside of the machine clean Frost precautions Avoid placing the machine in a location where the temperature i
15. close correctly loosen or tighten the adjustable feet until the ma chine is perfectly level spout or to a purpose made quick coupling tap such as the Press block The water pressure must be within the limits given in the Technical data Your local Wa ter Authority will advise you on the average mains pressure in your area The water inlet hose must not be kinked crushed or entangled when it is being con nected The appliance features inlet and drain hoses which can be turned either to the left or the right to suit the installation by means of the locknut The locknut must be correctly fitted to avoid water leaks Attention NOT all dishwasher models of have inlet and drain hoses provided with a locknut In this case this facility is not available If the appliance is connected to new pipes or pipes which have not been used for a long time you should run the water for a few mi nutes before connecting the inlet hose DO NOT use connection hoses which have previously been used on an old ap pliance i This appliance has been fitted with safe ty features which will prevent the water used in the appliance from returning back into the drinking water system This appliance complies with the applicable plumbing regulations Water inlet hose with safety valve After connecting the double walled water in let hose the safety valve is next to the tap Therefore the water inlet hose is only under pressure while the
16. e dishwasher is unplugged and the water tap turned off Degree of soil Type of load Programme description E Intensive Heavy soil Auto Any D Quick 2 Normal or light soil do Eco 3 Normal soil Crockery cutlery pots and pans Crockery cutlery pots and pans Crockery and cutlery Crockery and cutlery Prewash Main wash up to 70 C 2 intermediate rinses Final rinse Drying Prewash Main wash up to 45 C or 70 C 1 or 2 intermediate rinses Final rinse Drying Main wash up to 60 C Final rinse Prewash Main wash up to 50 C 1 intermediate rinse Final rinse Drying electrolux 17 Degree of soil Type of load Programme description y Glass Normal or light soil Delicate crockery and Main wash up to 45 C glassware 1 intermediate rinse Final rinse Drying 1 During the Auto programme the soil level of the dishes is given by how cloudy the water is The programme duration and consumptions can change This depends if the appliance is fully or not and on the level of soil on the dishes The appliance adjusts automatically the temperature of the water during the main wash 2 This is the perfect daily programme to clean a not fully load Ideal for a family of 4 persons who only want to load breakfast and dinner crockery and cutlery 3 Test programme for test institutes Consumption values Programme Duration in mi Water in litres nutes 1 Intensive 1 6 1 8 19 21 Auto 0 8 1 3 10 19
17. ead or on the gasket Use of rinse aid Warning Only use branded rinse aid for dishwashers Never fill the rinse aid dispenser with any other substances e g dishwasher cleaning agent liquid detergent This would damage the appliance Rinse aid ensures thorough rinsing and spot and streak free drying Rinse aid is automatically added during the last rinse 1 Open the container by pressing the re lease button A The dispenser holds about 110 ml of rinse aid which is sufficient for between 16 and 4 A 40 washing cycles depending upon the K dosage setting _ 3 Ensure that the lid is closed after every CV lt gt refill Sle i Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash According to the finish and drying results ob tained adjust the dose of rinse aid by means of the 6 position selector position 1 minimum 2 Add the rinse aid in the container The dosage position 6 maximum dosage maximum level for filling is indicated by The dose is factory set in position 4 max Increase the dose if there are drops of water or lime spots on the dishes after washing Reduce it if there are sticky whitish streaks on the dishes or a bluish film on glassware or knife blades Daily use e Check if it s necessary to refill with dish washer salt or rinse aid e Load cutlery and dishes into the dishwash er
18. ential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product Packaging material The packaging materials are environmentally friendly and can be recycled The plastic components are identified by markings e g gt PE lt gt PS lt etc Please dispose of the packaging materials in the appropriate con tainer at the community waste disposal fa cilities To avoid water leakage after installation make sure that the water couplings are tight If necessary have the domestic wir ing system socket replaced In case that the electrical cable has to be replaced contact your local Service Force centre The plug must be accessible after the appliance has been installed Never unplug the appliance by pull ing on the cable Always pull the plug The manufacturer accepts no liabil ity for failure to observe the above safety precautions A Warning When a unit is no longer being used e Pull the plug out of the socket e Cut off the cable and plug and dispose of them e Dispose of the door catch This pre vents children from trapping them selves inside and endangering their lives electrolux 25 26 electrolux electrolux 27 www electrolux com 11795948
19. hardness dH PTH mmol l Sil 70 Gil 125 Gh 12S 43 50 76 90 MOI Adjusting the water hardness setting Always remember that when performing the following operations selecting a washing programme setting the water softener level activating deactivating the rinse aid the appliance MUST be in setting mode Press the On Off button if a programme but ton light comes on the last performed or se lected programme is still set In this case to return to setting mode the programme has to be cancelled To cancel a set programme or a programme in progress Simultaneously press and hold the two func tion buttons B and C until all the programme button lights come on The programme has been cancelled and the machine is now in setting mode e Pour 1 litre of water into the salt container and then fill with dishwasher salt e Fill the rinse aid dispenser If you want to use combi detergent tablets such as 3 in 1 4 in 1 5 in 1 etc set the Multitab function See Multitab function The softener should be adjusted according to the hardness of the water in your area Your local Water Authority can advise you on the hardness of the water in your area The water softener must be set in two ways manually using the water hard ness dial and electronically manually electronically 2 level 10 yes 2 level 9 yes Water hardness dH TH mmol l 37 42 ald 175 GS vE 29 36 51 64
20. he filters in the base of the washing compartment are dirty or incorrectly positioned Too little or no detergent has been used e Where there are limescales deposits on the dishes the salt container is empty or incorrect level of the water softener has been set e The drain hose connection is not correct e The salt container cap is not properly closed The dishes are wet Rinse aid was not used and dull e The rinse aid dispenser is empty There are streaks e Decrease rinse aid dosage milky spots or a blu ish coating on glasses and dishes Water drops have e Increase rinse aid dosage dried onto glasses The detergent may be the cause Contact the detergent manufacturer con and dishes sumer care line If after all these checks the problem persists contact your local Service Force Centre Technical data Dimensions Width 45 cm Height 85 cm Depth 63 cm Electrical connection Voltage Information on the electrical connection is given on the rating plate Overall power Fuse on the inner edge of the dishwasher door Water supply pressure Minimum 0 05 MPa 0 5 bar Maximum 0 8 MPa 8 bar Capacity 9 place settings Hints for test institutes Testing in accordance with EN 60704 must aid dispenser have been filled with salt and be carried out with appliance fully loaded and rinse aid respectively and using the test pro using the test programme refer to Washing gramme refer to Washing programmes progra
21. ll start automatically i With the delay start function set the programme in progress indicator light is off Once the countdown of the delay start has elapsed the washing pro gramme will start automatically and the programme in progress indicator light comes on i The selection of the washing pro gramme and delay start can occur also with the door closed When you press a programme button you have ONLY 3 seconds to select a different programme or a delay start After these 3 seconds the selected pro gramme starts automatically AN Warning Interrupt or cancel a washing programme in progress ONLY if it s absolutely necessary Attention Hot steam may escape when the door is opened Open the door carefully Interrupt a washing programme in progress e Open the dishwasher door the pro gramme will stop Close the door the pro gramme will start from the point at which it was interrupted e Press the On Off all indicator lights will go off Press the On Off button again the pro gramme will start from the point at which it was interrupted 16 electrolux Cancel a delay start or a washing programme in progress e Simultaneously press and hold the two function buttons B and C until all the pro gramme lights come on e Cancelling a delay start will also cancel the washing programme You have to select the washing programme again e f anew washing programme is to be se lected check that there is detergent i
22. mmes Test in accordance with EN 50242 must be carried out when the salt container and rinse Full load 9 standard place settings Amount of detergent required 5 g 20 g Type B Rinse aid setting position 4 Type Ill i Testing MUST be carried out with e NO soft spikes e NO mini cutlery basket REMOVE these items from the upper basket electrolux 21 Arrangement upper basket without Arrangement lower basket salad bow k RY SS S SS SS D Ss QW q sees LT a Arrangement upper basket with salad bowl Arrangement cutlery basket a q _ f Cup racks dans A Ei An RNA Installation Warning Any electrical and or plumbing work required to install this appliance should be carried out by a qualified electrician and or plumber or competent person Fitting under a counter kitchen worktop or sink Remove all packaging before positioning the machine If possible position the machine next to a water tap and a drain 22 electrolux By removing the machine s worktop you can install it under a close fitting sink unit or a pre existing top providing the dimensions of the recess correspond to those shown in the picture Proceed as follows e Remove the machine s worktop by un screwing the two rear retaining screws
23. n the detergent dispenser End of the washing programme e The dishwasher will automatically stop and the programme in progress indicator light goes off e The End indicator light comes on e The light of the programme just ended re mains on Unloading the dishwasher e Hot dishes are sensitive to knocks The dishes should therefore be allowed to cool down before removing from the appliance e Empty the lower basket first and then the upper one this will avoid water dripping from the upper basket onto the dishes in the lower one e Water may appear on the sides and the door of the dishwasher as the stainless Washing programmes Washing programmes e Zero appears in the digital display 1 Switch off the dishwasher by pressing the On Off button 2 Open the dishwasher door leave it ajar and wait a few minutes before removing the dishes this way they will be cooler and the drying will be improved Standby mode If you do not switch off the appliance at the end of the washing programme the appli ance automatically goes into standby mode The standby mode decreases energy con sumption Three minutes after the end of the pro gramme all indicator lights go off and the digital display shows one horizontal bar Press one of the buttons not the on off but ton to go back to end of programme mode steel will eventually become cooler than the dishes When the washing programme has finished it is recommended that th
24. of the hose provided When connecting the drain hose to an under sink trap spigot the entire plastic mem brane A must be removed Failure to re move all the membrane will result in food particles building up over time eventually blocking the dishwasher drain hose spigot A 24 electrolux i Qur appliances are supplied with a se curity device to protect against the re turn of dirty water back into the machine If the spigot of your sink has a no return valve incorporated this can prevent the correct draining of your dishwasher We therefore advise you to remove it Electrical connection Warning Safety standards require the appliance to be earthed Prior to using the appliance for the first time ensure that the rated volt age and type of supply on the rating plate match that of the supply where the appliance is to be installed The fuse rating is also to be found on the rating plate Always plug the mains plug into a correctly installed shockproof sock et Multi way plugs connectors and ex tension cables must not be used This could constitute a fire hazard through overheating Environment concerns The symbol X on the product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent pot
25. penser with rinse aid 2 Activate the rinse aid dispenser 3 Set the rinse aid dosage to position 2 e The activation deactivation of the rinse aid is only possible with the Mul titab function active Activation deactivation of the rinse aid dispenser 1 Press the On Off button The dishwasher must be in setting mode 2 Simultaneously press and hold function buttons B and C until the lights of func tion buttons A B and C start flashing 3 Press function button B the lights of function buttons A and C go off while the light of function button B continues to flash The digital display indicates the cur rent setting 0 d Rinse aid dispenser deactivated id 4 To change the setting press button B again the digital display indicates the new setting 5 Tomemorize the operation switch off the dishwasher by pressing the On Off but ton Rinse aid dispenser activated If you decide to revert back to the use of individual detergents we ad vise that you electrolux 15 Deactivate the Multitab function 2 Fill up the salt container and the rinse aid dispenser again 3 Adjust the water hardness setting to the highest setting and perform 1 normal washing programme without loading any dishes 4 Adjust the water hardness setting according to the hardness of the wa ter in your area 5 Adjust the rinse aid dosage Select and start a washing programme Select the washing programme and delay sta
26. r maximum 20 cm position Soft spikes Soft spikes impede glassware to move dur ing the washing cycle or when the upper basket is moved Refer to the figures for a correct positioning of the soft spikes They can only be posi tioned on right hand side of the basket Once positioned correctly press them down firmly and make sure they do not move Caution BEFORE CLOSING THE DOOR MAKE SURE THAT THE SPRAY ARMS CAN ROTATE FREELY Adjusting the height of the upper basket If washing very large plates you can load them in the lower basket after moving the upper basket to the higher position Maximum height of the dishes in the upper the lower basket basket With upper basket raised Wam 31 cm With upper basket low 24 cm 27 cm ered To move to the higher position proceed as follows 1 Pull out the basket until it stops electrolux 13 2 Carefully lift both sides upwards until the To lower the basket to the original posi mechanism is engaged and the basket is tion proceed as follows stable 1 Pull out the basket until it stops 2 Carefully lift both sides upwards and then allow the mechanism to drop back down slowly keeping hold of it i Never lift or lower the basket on one side only When the basket is in the higher position cups cannot be placed on the cup racks After loading your machine always close the door as an open door can be a hazard Use of detergent Only use detergen
27. rt with the door slightly opened The start of the programme or the countdown of the delay start will occur only after the closure of the door Until then it is possible to modify the settings 1 Check that the baskets have been loaded correctly and that the spray arms are free to rotate 2 Check that the water tap is opened 3 Press the On Off button The dishwasher must be in setting mode 4 Press the button corresponding to the re quired programme see Washing pro grammes chart When a programme has been selected the corresponding light comes on The programme in progress indicator light comes on Close the dishwasher door the pro gramme starts automatically The programme in progress indicator light remains on Setting and starting the programme with delay start 1 After having selected the washing pro gramme press the delay start button until the flashing number of hours for the delay start appear in the digital display The start of the selected washing programme can be delayed for between 1 and 19 hours 2 Close the dishwasher door the count down starts automatically The number in the display is no longer flashing but fixed with static light 3 The countdown will decrease with steps of 1 hour 4 The opening of the door will interrupt the countdown Close the door the count down will continue from the point at which it was interrupted 5 Once the delay start has elapsed the pro gramme wi
28. s below O C If this is unavoidable empty the machine close the appliance door disconnect the water inlet pipe and empty it Moving the machine If you have to move the machine moving house etc 1 Unplug it 2 Turn the water tap off 3 Remove the water inlet and discharge hoses 4 Pull the machine out together with the hoses Avoid over tilting the machine during trans portation Switch off the dishwasher open the door and carry out the following suggested cor rective actions electrolux 19 Fault codes and malfunction Possible cause and solution e continuous flashing of the light of the running programme digital display shows 1 iG The dishwasher does not fill with water continuous flashing of the light of the running programme e digital display shows ic The dishwasher will not drain e continuous flashing of the light of the running programme e digital display shows 130 Anti flood device is activated The water tap is blocked or furred with lime scale Clean the water tap e The water tap is turned off Turn the water tap on The filter where present in the water inlet hose is blocked Clean the filter in the water inlet hose e The water inlet hose has not been correctly laid or it is kinked or squashed Check the water inlet hose connection The sink spigot is blocked Clean out the sink spigot e The water drain hose has not been correctly laid or it is kinked or
29. squashed Check the water drain hose connection e Close the water tap and contact your local Service Force Centre pS Ma function Possible cause and solution The programme does not start Once these checks have been carried out switch on the appliance The programme will continue from the point at which it was interrupted If the malfunction or fault code reappears contact your local Service Force Centre For other fault codes not described in the above chart please contact your local Serv ice Force Centre Contact your local Service Force Centre quoting the model Mod product number PNC and serial number S N e The dishwasher door has not been properly closed Close the door e The main plug is not plugged in Insert the main plug e The fuse has blown out in the household fuse box Replace the fuse e Delay start has been set If dishes are to be washed immediately cancel the delay start This information can be found on the rating plate located on the side of the dishwasher door So that you always have these numbers at hand we recommend you to make a note of them here 20 electrolux The wash results are not satisfactory The dishes are not The wrong programme has been selected clean e The dishes are arranged in such a way as to stop water reaching all parts of a surface The baskets must not be overloaded The spray arms do not rotate freely due to incorrect arrangement of the load T
30. to prevent damage to hydraulic and electric components Warning For electrical and water connection carefully follow the instructions given in the specific paragraphs 4 electrolux Product description Upper basket Water hardness dial Salt container Detergent dispenser Rinse aid dispenser Fal Rating plate Filters EJ Lower spray arm EX Upper spray arm Worktop electrolux 5 Control panel On off om Intensive Auto Quick co Glass Delay DRED EO 2 On Off button Programme selection buttons Delay start button Delay Indicator lights Digital display Function buttons Indicator lights S Programme in progress Comes on when a washing programme is set and remains on for all the duration of the washing pro gramme Goes off when the washing programme has ended gt End Comes on when a washing programme has ended Multitab function Indicates the activation deactivation of the multi tab function Refer to Multitab function Comes on when the special salt has run out Comes on when the rinse aid has run out 1 The salt and rinse aid indicator lights never come on while a washing programme is running even if filling with salt and or rinse aid is necessary The digital display e the level of hardness to which the water The digital display indicates softener is set 6 electrolux e the approximate remaining time of the run
31. ton A continues to flash The current level shows on the dig ital display Examples S L displayed level 5 0 L displayed level 10 4 To change the level press function but ton A Each time the button is pressed the level changes For the selection of the new level see the chart Examples If the current level is 5 by pressing function button A once level 6 is selected if the current level is 10 by pressing function button A once level 1 is selected 5 Tomemorize the operation switch off the dishwasher by pressing the On Off but ton To fill 1 Open the door remove the lower basket and unscrew the cap of the salt container by turning it anticlockwise 2 Pour 1 litre of water into the container this is necessary only before filling with salt for the first time 3 Using the funnel provided pour in the salt until the container is full 8 electrolux 5 Replace the cap tightly turning it clock wise until it stops with a click Do not worry if water overflows from the unit when filling with salt this is quite normal i The salt indicator light on the control panel can remain illuminated for 2 6 hours after the salt has been replen ished assuming the dishwasher re mains switched on If you are using salt that takes longer to dissolve then this can take longer The oper ation of the machine is not affected 4 Replace the cap making sure that there is no trace of salt on the screw thr
32. ts specifically de signed for use in dishwashers Please observe the manufacturer s dos ing and storage recommendations as stated on the detergent packaging Using no more than the correct amount of detergent contributes to reducing pol lution Fill with detergent 1 Open the lid 3 All programmes with prewash need an additional detergent dose 5 10 g that must be placed in the prewash detergent chamber 2 This detergent will be used during the prewash phase When using detergent tablets place the tablet in compartment 1 2 Fill the detergent dispenser 1 with de tergent The marking indicates the dosing levels 20 approximately 20 g of detergent 30 approximately 30 g of detergent 14 electrolux Multitab function This appliance is equipped with the Multitab function that allows the use of the Multitab combi detergent tablets These products are detergents with a com bined cleaning rinsing and salt functions They can also contain other different agents depending on which kind of tablets you choose 3 in 1 4 in 1 5 in 1 etc Check whether these detergents are suitable for your water hardness See the manufac turers instructions Once this function is selected it will remain active for all following wash programmes With the selection of this function the inflow of rinse aid and salt from each respective supply container is automatically deactivated and also the indicator
Download Pdf Manuals
Related Search