Ecodome User Manual
Contents
1. 1 1 Saving the Shipping Materials 1 1 Shipping Ecodome to Another Location 1 1 Contents of the Dome Box 1 2 Contents of the Housing Box 1 2 Contents of the Base Box 1 3 Building a Foundation 1 3 Installation Requirements 1 4 Foundation Layout 1 4 Assembling and Mounting the Base 1 6 Chapter 2 Installing the Fixture Connecting the Cabling 2 5 Final Component Assembly 2 11 Chapter 32. 1 3 Installation Requirements 1 4 Foundation Layout 1 4 Assembling and Mounting the Base 1 6 Chapter 2 Installing the Fixture Connecting the Cabling 2 5 Final Component Assembly 2 11 Chapter 3 Performing Maintenance Servicing the Fixture 3 1 Servicing Ecodome 3 1 Cleaning Ecodome 3 1 Checking Intake Exhaust 3 2 Replacing Air Filters 3 2 Oiling the Blower Motor
3. intro 2 DMX Data Cabling intro 3 Test Standards intro 3 Safety intro 3 Caution and Warning Symbols intro 4 Chapter 1 Installing the Ecodome Base Intended Audience 1 1 Unpacking Ecodome 1 1 Saving the Shipping Materials 1 1 Shipping Ecodome to Another Location 1 1 Contents of the Dome Box 1 2 Contents of the Housing Box 1 2 Contents of the Base Box 1 3 Building a Foundation
4. intro 1 Specifications intro 2 Model Numbers intro 2 Dimensions intro 2 Weight intro 2 Electrical Specifications intro 2 Environmental Specifications intro 2 DMX Data Cabling intro 3 Test Standards intro 3 Safety intro 3 Caution and Warning Symbols intro 4 Chapter 1 Installing the Ecodome Base Intended Audience 1 1 Unpacking Ecodome
5. 3 2 Figure 3 2 Oiling the blower motor 3 3 Table of Tables Table intro 1 Ecodome Optional Accessories intro 1 Ecodome User Manual Introduction intro 1 Introduction Introduction Introduction Introduction Congratulations on your purchase of the Ecodome architectural housing Ecodome is a weather resistant modular outdoor housing system designed for the Studio 250 series and the Studio 575 series of fixtures from High End Systems Inc Ecodome s ergonomic styling is both attractive and unobtrusive and gives a clean look to any architectural setting in which it operates Ecodome s high density polymer is colored neutral gray However Ecodome can be ordered in custom colors to match existing architectural schemes For more information on ordering a custom color see Optional Accessories below The Dome The dome is made of high impact UV resistant polycarbonate and allows full use of Studio 250 and Studio 575 series fixture s pan movement However the Ecodome housing limits the fixture s visible tilt range to the available 180 tilt area of the dome Once the light beam passes beyond the available 180 tilt area of the dome it will be blocked by the Ecodome housing Note If you plan to use a Studio Spot 575 or Studio Spot 250 fixture in Ecodo
6. 3 3 Appendix A Important Safety Information Appendice A Important Informations De S curit A 2 Anhang A Wichtige Sicherheitshinweise A 4 viii Ecodome User Manual Appendice A Informazioni Importanti Di Sicurezza A 5 Apendice A Informacion Importante De Seguridad A 7 Vigtig Sikkerhedsinformation DANMARK A 8 Table of Figures Figure 1 1 Ecodome road case 1 1 Figure 1 2 Ecodome dome 1 2 Figure 1 3 Contents of the housing box 1 2 Figure 1 4 Contents of the base box 1 3 Figure 1 5 Correct mounting position 1 3 Figure 1 6 Recommended foundation layout for Ecodome 1 5 Figure 3 1 Location of the air filters
7. for Ground Earth For more information on the fixture s power cord consult the fixture s user manual After inserting each wire tighten its terminal screw to 12 in lb 1 36 N m to secure the wire to the terminal block When you have finished tighten the cable clamp screws and replace the circuit box lid Live Neutral Ground terminal screws 2 8 Installing the Fixture Ecodome User Manual The mains power supply must include branch circuit protection sized in accordance with your local and national electrical codes High End Systems Inc recommends that you also use a Ground Fault Circuit Interrupt GFCI for all outdoor installations The cores in the Ecodome mains lead are colored in accordance with the following code green and yellow earth blue neutral brown live THIS EQUIPMENT MUST BE EARTHED Use a junction box to connect the Ecodome power cord to the mains power supply 5 junction box mains power supply Ecodome power cord Ecodome User Manual Installing the Fixture 2 9 2 Locate the fixture s DMX data connectors 6 data connectors 2 10 Installing the Fixture Ecodome User Manual Connect Ecodome s male data cable to the fixture s Data Out connector and Ecodome s female data cable to the fixture s Data In connector Use a junction box to connect the other end of Ecodome s data cables to either the controller or the next Ecodome on t
8. 1999 Printed in the USA C C ii Ecodome User Manual Contacting High End Systems U S and the Americas Sales Department High End Systems Inc 2217 West Braker Lane Austin TX 78758 USA voice 512 836 2242 FAX 512 837 5290 Customer Service High End Systems Inc 2227 West Braker Lane Austin TX 78758 USA voice 800 890 8989 24 hour FAX 512 834 9195 24 hour voice mail 512 837 3063 or 800 890 8989 U S West Coast High End Systems Inc 8200 Haskell Avenue Van Nuys CA 91406 USA voice 818 947 0550 FAX 818 908 8975 World Wide Web http www highend com Europe High End Systems GmbH Lohstrasse 22 D 85445 Schwaig Germany voice 49 8122 9903 0 FAX 49 8122 9903 33 Singapore High End Systems Singapore Pte Ltd 1 Tannery Road 06 05 Cencon 1 Singapore 1334 voice 65 742 8266 FAX 65 743 9322 Ecodome User Manual iii Declaration of Conformity according to ISO IEC Guide 22 and EN45104 Manufacturer s name Lightwave Research Manufacturer s address 2217 West Braker Lane Austin Texas 78758 USA Distributor s name High End Systems Inc Distributor s address 2217 West Braker Lane Austin Texas 78758 USA Declares that the product Product Name Ecodome Product Number Universal Ecodome 115 Universal Ecodome 208 230 Product Options All conforms to the following EEC directives 73 23 EEC as amended by 93 68 EEC 89 336 EEC as amen
9. 4 Installing the Ecodome Base Ecodome User Manual 2 Allow at least 24 in 61 cm clearance around intake and exhaust vents Warning Risk of fire and shock This product is to be installed by a qualified electrician only Installation Requirements 1 Ecodome must be installed in accordance with local and national building and electrical codes 2 The foundation on which Ecodome is installed must be at least 6 in 15 cm above ground level 3 Ecodome must not be installed in low lying areas subject to flooding Ecodome must be mounted on a site that provides adequate drainage so that Ecodome is never immersed in standing water 4 Ecodome model Universal Ecodome is to be used only with High End Systems fixture models Studio Color 575 M Studio Color 575 S Studio Color Studio Spot Studio Color 250 or Studio Spot 250 Foundation Layout You will need suitable foundation materials concrete steel wood etc to build a 32 in 81 cm minimum diameter foundation four 1 2 Unified National Coarse UNC studs for mounting Ecodome Use the following guidelines to build the Ecodome foundation 1 Construct a foundation of suitable material concrete steel wood etc that allows at least 32 in 81 cm minimum diameter Make sure the top of the foundation is at least 6 in 15 cm above ground level Ecodome User Manual Installing the Ecodome Base 1 5
10. Vor dem Ausf hren von Servicearbeiten ist das Ger t von der Stromversorgung zu trennen 2 Bei der Wartung der Leuchten ist sowohl der Lufteinla als auch der Luftaustrittsfilter zu pr fen z B beim Wechseln der Lampen Die Luftfilter sind zu ersetzen wenn sie sichtbar verschmutzt sind 3 Als Filter ist ein Fram CA5056 oder ein entsprechender Luftfilter zu verwenden CA 5056 Luftfilter k nnen bei Ihrem Vertragsh ndler von High End Systems Inc erworben werden Teile Nr 99170003 Appendice A Informazioni Importanti Di Sicurezza Condizioni per l omologazione ETL C ETL di Ecodome Ecodome un componente omologato ETL C ETL qualora siano rispettate le seguenti condizioni 1 Ecodome deve essere installato conformemente alle normative edili ed elettriche locali e nazionali 2 Il luogo di installazione di Ecodome deve essere rialzato dal suolo di almeno 15 cm Ecodome non deve inoltre essere messo in funzione in aree ribassate dove sussiste il pericolo di inondazione o in zone con presenza di acque morte profonde 3 Il modello Universal deve essere usato unicamente con apparecchiature Studio Color 575 M Studio Color 575 S Studio Color Studio Spot Studio Color 250 o Studio Spot 250 AVVERTENZA Per una protezione continua contro il rischio di scosse elettriche 1 Pericolo di incendio e scosse elettriche Questo prodotto deve essere installato solamente da un elettricista qu
11. des zones pouvant tre submerg es sous des eaux stagnantes 3 Le mod le Ecodome Universal doit tre utilis uniquement avec le mod le de projecteur Studio Color 575 M Studio Color 575 S Studio Color Studio Spot Studio Color 250 ou Studio Spot 250 AVERTISSEMENT Pour une protection continue contre l lectrocution 1 Risque d incendie et d lectrocution Ce produit doit tre install uniquement par un lectricien qualifi 2 Equipement de Classe I pour une protection continue contre l lectrocution branchez cet quipement une source d alimentation prot g e par un interrupteur de mise la terre 3 D branchez l appareil avant toute intervention de maintenance Ecodome User Manual Important Safety Information A 3 A 4 N installez pas d accessoire dans Ecodome sans contacter d abord le Service consommateurs de High End Systems AVERTISSEMENT Pour une s curit d op ration continue 1 Pour lire les instructions d installation et d importantes informations de s curit consultez la documentation livr e avec l appareil d clairage que vous utilisez 2 Le transport d Ecodome alors qu un projecteur est mont sur celui ci risque d endommager la fois le projecteur et le composant Ecodome 3 Cet appareil n est pas destin un usage domestique 4 Changer la lampe si elle est endommag e ou thermiquement d fo
12. 1 2 Install four 1 2 mounting studs into the foundation in a square pattern with the center of the studs measuring 17 inches apart see Figure 1 6 Figure 1 6 Recommended foundation layout for Ecodome 6 00 min 4 mounting studs 32 00 8 50 17 00 32 00 8 50 17 00 32 00 1 6 Installing the Ecodome Base Ecodome User Manual Assembling and Mounting the Base This section shows how to mount the Ecodome base on the foundation you have already prepared You will need ratchet and 3 4 deep socket 6 extension scissors four 1 2 regular washers supplied with Ecodome four 1 2 split washers supplied with Ecodome four 1 2 mounting nuts supplied with Ecodome Use scissors to cut the cable tie wrap on the cables under the Ecodome base 1 power and DMX data cables Ecodome User Manual Installing the Ecodome Base 1 7 1 Extend the power and DMX data cables through either of the recessed areas on the Ecodome base 2 Data Out Data In power recessed areas on base Place the four Ecodome mounting holes over the four studs in your foundation 3 Mounting holes 4 1 8 Installing the Ecodome Base Ecodome User Manual Place a 1 2 regular washer a 1 2 split washer and a 1 2 hex nut over each of the four foundation studs inside the Ecodome base 4 Use a ratchet to tighten all four 1 2 hex nuts securely 5 Ecodome User M
13. 1 Figure 1 1 Ecodome road case 1 1 Figure 1 2 Ecodome dome 1 2 Figure 1 3 Contents of the housing box 1 2 Figure 1 4 Contents of the base box 1 3 Figure 1 5 Correct mounting position 1 3 Figure 1 6 Recommended foundation layout for Ecodome 1 5 Figure 3 1 Location of the air filters 3 2 Figure 3 2 Oiling the blower motor 3 3 1 12 Studio Spot 250 Studio Color 250 User Manual Studio Spot 250 Studio Color 250 User Manual 1 13 Table intro 1 Ecodome Optional Accessories intro 1
14. Kundendienstabteilung von High End Systems in Verbindung setzen WARNUNG Zur sicheren Betriebsweise 1 Lesen Sie die Installationsanleitungen und wichtigen Sicherheitshinweise in der Dokumentation zur Leuchte 2 Der Versand von Ecodome mit einer installierten Leuchte k nnte sowohl die Leuchte als auch Ecodome besch digen 3 Nicht f r den Hausgebrauch bestimmt 4 Falls die Lampe besch digt oder durch W rmeeinwirkung verformt ist mu sie ausgewechselt werden WARNUNG ZUM SCHUTZ GEGEN BERM SSIGE ULTRAVIOLETT UV BESTRAHLUNG 1 Benutzen Sie dieses Ger t nur wenn das komplette Lampengeh use fest eingebaut ist ebenfalls d rfen keine der Schutzabdeckungen Linsen oder der UV Schutz Besch digungen aufweisen Ecodome User Manual Important Safety Information A 5 A 2 Die Schutzabdeckungen Linsen und der UV Schutz m ssen ausgewechselt werden wenn sie sichtlich derma en besch digt sind da sie ihre Wirksamkeit einb en z B infolge von Rissen oder tiefen Kratzern 3 Nie direkt in die eingeschaltete Lampe schauen Installationsanleitungen 1 Um die Lufteinla sowie um die Luftaustritts ffnung ist ein Sicherheitsabstand von 61 cm 24 Zoll erforderlich Das Ger t nicht in tiefgelegenen Gebieten die h ufig berschwemmungen ausgesetzt sind oder in Gebieten mit tief stehendem Wasser betreiben 2 Der Ecodome darf nicht an der Wand oder kopfstehend befestigt werden Wartungsanleitungen 1
15. Performing Maintenance Servicing the Fixture 3 1 Servicing Ecodome 3 1 Cleaning Ecodome 3 1 Checking Intake Exhaust 3 2 Replacing Air Filters 3 2 Oiling the Blower Motor 3 3 Appendix A Important Safety Information Appendice A Important Informations De S curit A 2 Anhang A Wichtige Sicherheitshinweise A 4 Appendice A Informazioni Importanti Di Sicurezza A 5 Apendice A Informacion Importante De Seguridad A 7 1 10 Studio Spot 250 Studio Color 250 User Manual Vigtig Sikkerhedsinformation DANMARK A 8 Studio Spot 250 Studio Color 250 User Manual 1 1
16. TIAL OR TOTAL FAILURE OF ANY PRODUCT REGARDLESS OF THE FORM OF ACTION WHETHER IN CONTRACT TORT INCLUDING NEGLIGENCE STRICT LIABILITY OR OTHERWISE AND WHETHER OR NOT SUCH DAMAGE WAS FORESEEN OR UNFORESEEN Warranty is void if the product is misused damaged modified in any way or for unauthorized repairs or parts This warranty gives you specific legal rights and you may also have other rights which vary from state to state Ecodome User Manual vii Table of Contents Introduction The Dome intro 1 Optional Accessories intro 1 Specifications intro 2 Model Numbers intro 2 Dimensions intro 2 Weight intro 2 Electrical Specifications intro 2 Environmental Specifications
17. User Manual High End Systems Inc 2217 West Braker Lane Austin TX 78758 U S A 512 836 2242 www highend com p n 60600135 Version 1 0 ecodome For the latest product updates and information not contained in this manual visit the High End Systems Product Support page at http info highend com service prodsupt html Ecodome User Manual i ecodome User Manual High End Systems Inc 1999 All Rights Reserved Information and specifications in this document are subject to change without notice High End Systems Inc assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual Trademarks used in this text Lightwave Research High End Systems Studio Color and LithoPatterns are registered trademarks and Studio Spot Studio Color 250 Studio Spot 250 the Lightwave Research logo and the High End Systems globe logo are trademarks of High End Systems Inc Belden is a registered trademark of Belden Inc Fram is a registered trademark of Allied Signal ETL and C ETL are registered trademarks of Intertek Testing Services Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products High End Systems disclaims any proprietary interest in trademarks and trade names owned by others For patent information see the inside back cover of this manual Ecodome User Manual P N 60600135 Version 1 0 February
18. V ENV 50204 1996 Level 2 3 V m Safety Maximum ambient temperature Ta 40 C 104 F Maximum exterior surface temperature 62 C 144 F Suitable for mounting on normally flammable surfaces Not for residential use intro 4 Introduction Ecodome User Manual Caution and Warning Symbols The following international symbols appear in margins throughout this manual to highlight caution and warning messages Caution This symbol appears adjacent to Caution messages Not heeding these messages could result in personal injury and or damage to equipment Warning This symbol appears adjacent to high voltage warning messages Not heeding these messages could result in serious personal injury Fire Hazard This symbol indicates that a fire hazard is present Not heeding these messages could result in serious personal injury Ecodome User Manual Installing the Ecodome Base 1 1 1 Chapter 1 Chapter 1 Chapter 1 Chapter 1 Installing the Ecodome Installing the Ecodome Installing the Ecodome Installing the Ecodome Base Base Base Base Intended Audience Ecodome must be installed by a qualified electrician only This manual is intended for electricians and or building contractors already familiar with electrical wiring and construction Unpacking Ecodome Ecodome ships in three separate boxes one for the dome one for the housing and one for the base Carefully unpack each
19. alificato A 6 Important Safety Information Ecodome User Manual 2 Apparecchiatura di classe I per garantire una continua protezione contro le scosse elettriche collegare questo dispositivo a una fonte di alimentazione elettrica con messa a terra adeguata 3 Scollegare dalla corrente prima di effettuare la manutenzione AVVERTENZA Per garantire un funzionamento sicuro e duraturo 1 Fare riferimento alla documentazione acclusa al dispositivo in dotazione per le istruzioni di installazione e le informazioni sulla sicurezza 2 La spedizione di Ecodome con un apparecchiatura installata potrebbe provocare danni sia all apparecchiatura sia a Ecodome 3 Questa apparechiatura non e per uso domestico 4 Cambiare la lampada in caso si danneggi o deformi per le alte temperature AVVERTENZA PER PROTEGGERSI CONTRO LE RADIAZIONI DEI RAGGI ULTRAVIOLETTI Non usare questa apparecchiatura se il dispositivo di chiusura della almpada non completamente fissato o se gli schermi protettivi le lenti o gli schermi ultravioletti si sono visibilmente danneggiati di maniera tale che la loro efficacia sia stata ridotta ad esempio se vi sono visibili spaccature o graffi profondi Mai guardare direttamente verso la lampadina quando sia accesa Istruzioni per l installazione 1 Lasciare uno spazio libero di almeno 61 cm attorno ai condotti di ingresso e di scarico Non operare l unit in aree ribassate dove sussiste il pericolo di inond
20. anual Installing the Fixture 2 1 2 Chapter 2 Chapter 2 Chapter 2 Chapter 2 Installing the Fixture Installing the Fixture Installing the Fixture Installing the Fixture You should have already prepared the site and mounted the Ecodome base as described in Chapter 1 before following the instructions in this chapter You will need a fixture suitable for mounting in Ecodome see Installation Requirements on page 1 4 ratchet and 3 4 deep socket 2 Philips head torque measuring screwdriver 3 32 allen wrench supplied with Ecodome two light blocks supplied with Ecodome four 8 32 x 3 8 pan head screws supplied with Ecodome four 3 8 hex screws supplied with Ecodome four 3 8 regular washers supplied with Ecodome four 3 8 hex nuts supplied with Ecodome 1 Locate the support beams on the Ecodome base support beams 2 2 Installing the Fixture Ecodome User Manual 2 Determine whether the support beams are correctly assembled for the fixture you wish to install If you wish to install a Studio Spot 575 fixture position the support beams in holes 2 and 3 If you wish to install a Studio Color S Studio Color M Studio Color 575 Studio Spot 250 or Studio Color 250 fixture position the support beams in holes 1 and 2 Studio Spot 575 fixtures Studio Color S Studio Color M Studio Color 575 Studio Color 250 and Studio Spot 250 fixtures hole 1
21. ated power and voltage of the fixture you plan to install inside Ecodome Warning Class I equipment For continued protection against electric shock connect this equipment to a power source that is protected by a Ground Fault Circuit Interrupt GFCI Environmental Specifications Ingress Protection IP 45 Suitable for outdoor use 720 mm 28 36 in 64 mm R 2 50 in 146 mm 5 75 in 177 mm 7 00 in 576 mm 22 70 in 395 mm 15 56 in 1150 mm 45 26 in 800 mm 31 50 in 711 mm 28 00 in Ecodome User Manual Introduction intro 3 DMX Data Cabling DMX data cables Belden 9841 or equivalent meets specifications for EIA RS 485 applications with characteristics listed below 2 conductor twisted pair plus a shield maximum capacitance between conductors 30 pF ft maximum capacitance between conductor and shield 55 pF ft maximum resistance of 20 1000 ft nominal impedance 100 140 22 24 AWG with insulation having a dielectric rating of 300 volts or higher DMX data connectors 3 pin male and female XLR connectors DMX data terminators male XLR connector with 120 ohm terminator Test Standards Ecodome conforms to the following standards UL 1572 EN 60598 1 CSA 22 2 No 9 EMC standards EN 55022 Class A ITE IEC 801 2 Level 3 6 8kV IEC 801 3 Level 2 3 V m IEC 801 4 Level 2 1kV 5k
22. ay the dome off with water 3 2 Performing Maintenance Ecodome User Manual 2 After cleaning away built up debris use a soft cloth a wet cotton rag chamois or cheese cloth is recommended and water or mild glass cleaner to wipe away dirt and debris from the outer dome surface Caution Do not use paper towels or other abrasive materials to clean the dome doing so can leave scratches which may impair image quality 3 Optional As a final cleaning dampen a soft cloth with denatured rubbing alcohol to thoroughly clean the dome s surface Checking Intake Exhaust You must leave at least 24 inches 61 cm clearance around both the intake and exhaust vents located on opposite sides of the Ecodome base Because wind and weather conditions can cause debris to build up around the vents you should regularly inspect for any of the following Grass clippings or leaves Use your hands or a vacuum to clear away leaves and clippings Water snow or soil Accumulations of water or soil within 24 inches 61 cm of Ecodome s intake or exhaust could prevent the fixture from operating properly or pose a major hazard to the fixture If any of the above regularly accumulate around Ecodome contact High End Systems customer service see Contacting High End Systems on page ii Replacing Air Filters Caution Electrically isolate Ecodome before following these instructions Check Ecodome s intake and exhaust air
23. azione o in zone con presenza di acque morte profonde 2 Ecodome non pu essere montato su una parete o sottosopra Istruzioni per la manutenzione 1 Scollegare dalla dalla corrente prima di effettuare la manutenzione 2 Controllare i filtri dell aria dei condotti di ingresso e di scarico a ogni intervento di manutenzione ad esempio quando si cambiano le lampadine Questi filtri devono essere cambiati quando appaiono otturati da depositi e sporco 3 Utilizzare un filtro dell aria Fram CA 5056 o equivalente I filtri CA 5056 sono disponibili presso distributori e rivenditori High End Systems Inc numero di ordinazione 99170003 Ecodome User Manual Important Safety Information A 7 A Apendice A Informacion Importante De Seguridad Condiciones de aceptabilidad para el reconocimiento ETL C ETL de Ecodome Ecodome es un componente reconocido por ETL C ETL cuando se cumplen las condiciones de aceptabilidad siguientes 1 Ecodome debe instalarse de acuerdo con los c digos locales y nacionales de construcci n y electricidad 2 El cimiento sobre el cual se instale Ecodome debe estar por lo menos a 15 cm 6 pulgadas sobre el nivel del suelo adem s no debe operarse el Ecodome en reas bajas susceptibles de ser inundadas o en reas que puedan sufrir aguas estancadas 3 El modelo Ecodome llamado Universal debe utilizarse nicamente con el accesorio Studio Color 575 M Studio Color 575 S Studio Col
24. box and inspect the contents for damage If any of the items listed in this section are missing or damaged you must notify both the shipping agent and your sales agent immediately Saving the Shipping Materials Do not discard the shipping box and packing materials The box and packing materials are specifically designed to protect the product during transport High End Systems Inc assumes no responsibility for products damaged during transport Therefore you should return a product for repair in its original shipping carton and packing materials Note Before sending anything to the factory be sure to call your High End Systems Inc dealer distributor for a Return Material Authorization RMA number The factory cannot accept any goods shipped without an RMA number Shipping Ecodome to Another Location Ecodome was not designed to be shipped while a fixture is installed inside Ecodome If you need to ship Ecodome to another location High End Systems Inc strongly recommends you do the following 1 Remove the fixture installed in Ecodome and repack the fixture in its original packaging and container 2 Either disassemble Ecodome and repack it in its original packaging and containers or pack the fully assembled Ecodome in a road case see Figure 1 1 Figure 1 1 Ecodome road case 1 2 Installing the Ecodome Base Ecodome User Manual For more information on obtaining an Ecodome road case see Optional Accesso
25. ch an extent that their effectiveness is impaired for example by cracks or deep scratches 3 Never look directly at the lamp while the lamp is on Installation Instructions 1 Allow at least 24 inches 61 cm clearance around intake and exhaust Do not operate in low lying areas subject to flooding or in areas subject to standing water 2 Ecodome cannot be mounted on a wall or upside down Maintenance Instructions 1 Disconnect power before servicing 2 Check both intake and exhaust air filters whenever you service the fixture for example when you change lamps Air filters must be replaced when they are visibly clogged with dirt 3 You must use a Fram CA 5056 air filter or the equivalent You can purchase CA 5056 air filters from your High End Systems Inc dealer distributor part number 99170003 Appendice A Important Informations De S curit Conditions d acceptation pour la reconnaissance d Ecodome par l ETL C ETL Ecodome est un composant reconnu par l ETL C ETL lorsque les conditions suivantes sont satisfaites 1 Ecodome doit tre install conform ment aux codes de r glementation locaux et nationaux concernant le b timent et les installations lectriques 2 Le support de base sur lequel est install Ecodome doit tre une distance minimum de 15 cm 6 pouces au dessus du niveau du sol de plus Ecodome ne doit pas tre utilis dans des zones basses susceptibles d tre inond es ou dans
26. ck until the screws are in the small end of the keyhole slots Tighten the screws securely Studio Spot 575 Studio Spot 250 Replace the outer screws on the bottom of the fixture s yoke Install the light block Ecodome User Manual Installing the Fixture 2 5 2 Connecting the Cabling You will need 2 Phillips head screwdriver flat head screwdriver with a 3 16 blade Locate the Ecodome circuit box on the Ecodome base 1 circuit box 2 Using a 2 Phillips head screwdriver loosen but do not remove the two screws from the circuit box lid Slide the circuit box lid to the side so that the screws are positioned in the large end of the keyhole slot Pull the circuit box lid out and over the screws to remove the lid keyhole slots loosen the two screws slide the lid 2 6 Installing the Fixture Ecodome User Manual 3 Using a flat head screwdriver loosen the two cable clamp screws Insert the fixture s power cord through the cable clamp into the circuit box Ecodome power cord power in fixture power cord cable clamp screws Ecodome User Manual Installing the Fixture 2 7 2 4 Using a flat head screwdriver loosen the three Ecodome terminal screws reserved for the fixture s cable shaded below Insert the fixture s Live Neutral and Ground Earth wires into the appropriatly marked terminal The Ecodome terminals are marked L for Live N for Neutral and
27. ded by 92 31 EEC and 93 68 EEC Equipment referred to in this declaration of conformity first manufactured in 1999 in compliance with the following standards Safety EN 60598 1 1993 EMC EN 55022 1987 Class A ITE IEC 801 2 1991 Level 3 6 8 kV IEC 801 3 1991 Draft 5 Level 2 3 V m IEC 801 4 1988 Level 2 1 kV 0 5 kV ENV 50204 1996 Level 2 3 V m USA July 15 1999 Kenneth Stuart Hansen Compliance Engineer iv Ecodome User Manual Product Modification Warning High End Systems products are designed and manufactured to meet the requirements of United States and International safety regulations Modifications to the product could affect safety and render the product non compliant to relevant safety standards Mise En Garde Contre La Modification Du Produit Les produits High End Systems sont con us et fabriqu s conform ment aux exigences des r glements internationaux de s curit Toute modification du produit peut entra ner sa non conformit aux normes de s curit en vigueur Produktmodifikationswarnung Design und Herstellung von High End Systems entsprechen den Anforderungen der U S Amerikanischen und internationalen Sicherheitsvorschriften Ab nderungen dieses Produktes k nnen dessen Sicherheit beeintr chtigen und unter Umst nden gegen die diesbez glichen Sicherheitsnormen versto en Avvertenza Sulla Modifica Del Prodotto I prodotti di High End Systems sono stati progettati e fabbricati per soddi
28. enbau und der Intbetriebnahme dieses Ger ts alle Anleitungen sorgf ltig durchlesen Informazioni Importanti Di Sicurezza Le istruzioni sulla protezione da incendi folgorazione esposizione eccessiva a raggi ultravioletti UV e infortuni sono contenute nell appendice A Si prega di leggere tutte le istruzioni prima di assemblare montare e azionare l apparecchiatura Informacion Importante De Seguridad En el Ap ndice A se encuentran instrucciones sobre protecci n continua contra incendios descarga el ctrica exposici n excesiva a radiaci n ultravioleta UV y lesiones personales Lea por favor todas las instrucciones antes del ensamblaje montaje y operaci n de este equipo Warranty Information Limited Warranty Unless otherwise stated your product is covered by a two year parts and labor limited warranty It is the owner s responsibility to furnish receipts or invoices for verification of purchase date and dealer or distributor If purchase date cannot be provided date of manufacture will be used to determine warranty period Returning an Item Under Warranty for Repair It is necessary to obtain a Return Material Authorization RMA number from your dealer or point of purchase BEFORE any units are returned for repair The manufacturer will make the final determination as to whether or not the unit is covered by warranty Lamps are covered by the lamp manufacturer s warranty Any Product unit or parts returned
29. filters whenever you service the fixture installed in Ecodome for example when you change lamps Ecodome s air filters must be replaced when they are visibly clogged with dirt To replace the air filter 1 Use the tamper proof screwdriver shipped with Ecodome to remove the base clamp 2 Carefully lift the housing and dome from the base and fixture 3 Locate the air filters see Figure 3 1 4 Loosen the three air filter cover thumbscrews surrounding the air filter and remove the air filter cover Figure 3 1 Location of the air filters intake air filter exhaust air filter under blower assembly Ecodome User Manual Performing Maintenance 3 3 3 Note The entire blower assembly serves as the exhaust air filter cover To access the exhaust air filter loose the three thumbscrews around the base of the blower assembly and lift the entire blower assembly off the base 5 Replace the air filter You must use a Fram CA 5056 air filter You can purchase CA 5056 air filters from your High End Systems dealer distributor see Optional Accessories on page intro 1 6 Replace the air filter cover and tighten the air filter cover thumbscrews 7 Replace the housing and dome over the base Use the tamper proof screwdriver to tighten the base clamp Oiling the Blower Motor You should oil the blower motor every six months Caution Electrically isolate Ecodome before following these instruc
30. forming Maintenance Performing Maintenance Performing Maintenance Performing Maintenance You must observe the following warnings and cautions when performing any type of service on either Ecodome or the fixture installed inside Ecodome Warnings 1 Disconnect power before servicing 2 Consult the documentation provided with the fixture installed inside Ecodome for important safety information 3 Do not operate this equipment without complete lamp enclosure in place or if shields lenses or ultraviolet screens are damaged 4 Change shields lenses or ultraviolet screens if they have become visibly damaged to such an extent that their effectiveness is impaired for example by cracks or deep scratches 5 Never look directly at the lamp while the lamp is on Caution This fixture must be serviced by qualified personnel The information listed in this section is intended to assist qualified service personnel only Servicing the Fixture Consult the fixture s documentation for recommended fixture cleaning and maintenance procedures Servicing Ecodome Some basic recommended service procedures for Ecodome are listed below Cleaning Ecodome To clean the housing use a cloth and non abrasive household soap and or cleaner to wipe away built up dirt from the housing To clean the dome leave the dome on the Ecodome unit and follow the steps below 1 If mud or other debris has accumulated on the dome first spr
31. he DMX link 7 junction box Ecodome s DMX cables Ecodome User Manual Installing the Fixture 2 11 2 Final Component Assembly This section describes how to assemble the final components before putting Ecodome into use You will need four housing labels supplied with Ecodome tamper resistant screwdriver tool supplied with Ecodome Remove the paper backing from the housing labels and carefully apply one label to each recessed area at the top of the housing Use firm even pressure to prevent bubbles from forming under the label 1 2 12 Installing the Fixture Ecodome User Manual Place the Ecodome housing with attached clamp over the Ecodome base with attached clamp Place the dome over the housing 2 clamps Ecodome User Manual Installing the Fixture 2 13 2 Secure the clamps by tightening the clamp bolts with the tamper resistant screwdriver tool Tighten the bolts until you cannot rotate either the dome or the housing Note If you mounted Ecodome on an incline orient the clamp bolts and the base vents 90 away from the direction of the incline to provide added protection against moisture accumulating inside Ecodome 3 45 maximum Moisture Clamp bolts vents located on both sides of Ecodome water flow 2 14 Installing the Fixture Ecodome User Manual Ecodome User Manual Performing Maintenance 3 1 3 Chapter 3 Chapter 3 Chapter 3 Chapter 3 Per
32. hole 2 hole 3 3 Use two people to place the fixture on the Ecodome support beams If you are installing a Studio Color S Studio Color 575 or Studio Spot 575 fixture you must orient the fixture so that the fixture s heatsink faces the Ecodome blower blower heatsink on Studio Color S Studio Color 575 and Studio Spot 575 fixtures Ecodome User Manual Installing the Fixture 2 3 2 4 Secure the fixture to the Ecodome base by installing a 3 8 hex screw 3 8 flat washer and a 3 8 hex nut through the top of the Ecodome support beam and each of the four mounting holes on the fixture s bottom plate 2 4 Installing the Fixture Ecodome User Manual 5 If you are installing a Studio Spot 575 or Studio Spot 250 fixture you must attach a light block to each side of the fixture The light blocks will prevent damage to the inside of the Ecodome housing Caution Failure to install light blocks will result in damage to the Ecodome Housing Using a 3 32 allen wrench for Studio Spot 575 fixtures or a 2 Phillips head screwdriver for Studio Spot 250 fixtures remove the two outer screws on the bottom of the fixture s yoke Insert an 8 32 pan head screw in each outer screw hole on the bottom of the fixture s yoke Do not fully tighten the screws Install the light block by placing the large ends of its keyhole slots over the two 8 32 pan head screws on the fixture s yoke Lightly press down on the light blo
33. io Color 250 or Studio Spot 250 WARNING For Continued Protection Against Electric Shock 1 Risk of fire and electric shock This product is to be installed by a qualified electrician only 2 Class I equipment For continued protection against electric shock connect this equipment to a ground fault protected power source only 3 Disconnect power before servicing 4 Do not install an accessory in Ecodome unless you first contact High End Systems customer service 5 IMPORTANT The cores in the mains lead are colored in accordance with the following code green and yellow earth blue neutral brown live 6 THIS EQUIPMENT MUST BE EARTHED WARNING For Continued Safe Operation 1 Consult the documentation provided with the luminaire you are using for installation instructions and important safety information 2 Shipping Ecodome to another location with a fixture installed could result in damage to both the fixture and to Ecodome 3 Not for residential use 4 Change the lamp if it becomes damaged or thermally deformed Warning For Continued Protection Against Exposure To Excessive Ultraviolet UV Radiation 1 Do not operate this equipment without complete lamp enclosure in place or if shields lenses or ultraviolet screens are damaged A 2 Important Safety Information Ecodome User Manual 2 Change shields lenses or ultraviolet screens if they have become visibly damaged to su
34. me you must install light blocks to protect the Ecodome housing from possible damage due to the fixture s light beam shining directly on the inside of the housing For more information on installing light blocks see page 2 4 Optional Accessories Table 1 below shows the optional accessories available for Ecodome from your High End Systems dealer distributor Call For more information about optional accessories contact either your High End Systems dealer distributor High End Systems sales department or visit the High End Systems web site For contact information see Contacting High End Systems on page ii Table intro 1 Ecodome Optional Accessories Name Part Number Optional Ecodome colors Call Fram CA 5056 air filter 99170003 Round dome 28010005 Ecodome road case 28070001 intro 2 Introduction Ecodome User Manual Specifications Model Numbers Model Universal Ecodome Manufacturer Lightwave Research Distributor High End Systems Inc 2217 W Braker Lane Austin Texas 78758 USA Dimensions Height 45 in 115 cm Width 32 in 80 cm Depth 32 in 80 cm Weight Dome 7 lbs 3 kg Housing 15 lbs 7 kg Base 45 lbs 20 kg Assembled no fixture installed 67 lbs 30 kg Electrical Specifications Universal Ecodome 115 115V 50 60 Hz 930W maximum Universal Ecodome 208 230 208 230V 50 60 Hz 930W maximum Refer to the fixture s user manual for the r
35. mprometida Por ejemplo en el caso de grietas o rayaduras profundas 3 Jam s mire directamente a la l mpara en tanto sta est encendida A 8 Important Safety Information Ecodome User Manual Instrucciones de instalaci n 1 Deje por lo menos 61 cm 24 pulgadas de espacio alrededor de la entrada y el escape No opere en reas bajas susceptibles a inundaciones o en reas donde pueda sufrir aguas profundas y estancadas 2 El Ecodome no puede montarse en una pared ni boca abajo Instrucciones de mantenimiento 1 Desconecte la alimentaci n el ctrica antes de dar servicio 2 Revise los filtros de aire de entrada y de escape siempre que d servicio al accesorio por ejemplo cuando cambie l mparas Los filtros de aire deben reemplazarse cuando presenten obstrucciones de suciedad 3 Debe utilizar un filtro de aire Fram CA 5056 o equivalente Puede adquirir filtros de aire CA 5056 mediante su distribuidor de High End Systems Inc n mero de pieza 99170003 Vigtig Sikkerhedsinformation DANMARK Advarsel Beskyttelse mod elektrisk chock Vigtigt Lederen med gul groen isolation maa kun tilsluttes en klemme maerket eller Studio Spot 250 Studio Color 250 User Manual 1 9 Introduction The Dome intro 1 Optional Accessories
36. or Studio Spot Studio Color 250 o Studio Spot 250 modelo ADVERTENCIA Para una protecci n constante contra las descargas el ctricas 1 Peligro de incendio y descarga el ctrica Unicamente un electricista calificado debe instalar este producto 2 Equipo Clase I Para una protecci n constante contra las descargas el ctricas conecte este equipo nicamente a una fuente de alimentaci n protegida contra fallas de tierra 3 Desconecte la alimentaci n antes de dar servicio 4 No instale un accesorio en el Ecodome sin antes ponerse en contacto con Servicio a clientes de High End Systems ADVERTENCIA Para una operaci n segura 1 Consulte la documentaci n proporcionada con la luminaria que utiliza para obtener las instrucciones de instalaci n e informaci n importante de seguridad 2 El env o de Ecodome con un accesorio instalado puede da ar tanto al accesorio como al Ecodome 3 Prohibido su uso en ambientes residenciales 4 Cambie la l mpara si sta se aver a o deforma por acci n t rmica ADVERTENCIA PARA PROTECCI N CONTINUA CONTRA LA EXPOSICI N A RADIACI N ULTRAVIOLETA UV EXCESIVA 1 No opere este equipo sin tener colocada en su lugar la caja protectora completa de la l mpara o bien si el blindaje los lentes o las pantallas ultravioletas est n da adas 2 Cambie el blindaje los lentes o las pantallas ultravioleta si nota una aver a visible a tal grado que su eficacia se vea co
37. ributeurs agr s High End Systems Inc num ro de pi ce 99170003 A 4 Important Safety Information Ecodome User Manual Anhang A Wichtige Sicherheitshinweise Anforderung der ETL C ETL Norm f r Ecodome Ecodome entspricht der Norm einer von ETL C ETL akzeptierten Komponente wenn die folgenden Anforderungen erf llt sind 1 Ecodome mu gem der rtlichen und nationalen elektrischen Richtlinien und Bauvorschriften installiert werden 2 Das Fundament auf welches Ecodome installiert wird mu sich mindestens 15 cm 6 Zoll ber der Grundgleiche befinden Au erdem ist Ecodome nicht in tiefgelegenen Gebieten die berschwemmungen ausgesetzt sind oder in Gebieten mit stehendem Wasser zu betreiben 3 Das Ecodome Modell Universal ist nur mit dem Leuchtenmodell Studio Color 575 M Studio Color 575 S Studio Color Studio Spot Studio Color 250 oder Studio Spot 250 zu verwenden WARNUNG Zum Schutz vor elektrischen Schl gen 1 Feuergefahr und Gefahr eines elektrischen Schlages Dieses Produkt sollte nur von einem qualifizierten Elektriker installiert werden 2 Ger t der Klasse I Zum Schutz vor elektrischen Schl gen ist dieses Ger t an eine mit Erdschlu geerdete Stromversorgung anzuschlie en 3 Vor dem Ausf hren von Servicearbeiten ist das Ger t von der Stromversorgung zu trennen 4 Bevor Zubeh rger te in Ecodome installiert werden m ssen Sie sich mit der
38. ries on page intro 1 Caution Shipping Ecodome with a fixture installed could damage both the fixture and Ecodome Contents of the Dome Box The dome box contains one round dome see Figure 1 2 Carefully remove the dome and inspect it for cracks or scratches If you notice cracks or scratches not caused by shipping damage carefully repack it in its original container and contact High End Systems customer service see Contacting High End Systems on page ii Contents of the Housing Box The housing box contains one housing with an attached clamp and four labels see Figure 1 3 Figure 1 2 Ecodome dome Figure 1 3 Contents of the housing box clamp LIGHTWAVE LIGHTWAVE Ecodome User Manual Installing the Ecodome Base 1 3 1 Contents of the Base Box The base box contains one base with an attached clamp two light blocks and various hardware needed for installation see Figure 1 4 Building a Foundation Cautions 1 Ecodome should not be mounted on a wall upside down or on a surface inclined more than 45 Figure 1 4 Contents of the base box tamper resistant screwdriver 1 2 regular washers 4 1 2 split washers 4 1 2 hex nuts 4 3 8 hex nuts 4 3 8 hex screws 4 3 8 regular washers 4 3 32 allen wrench light block 2 8 32 x 3 8 pan head screws 4 clamp Figure 1 5 Correct mounting position 0 level 45 maximum OK OK 1
39. rm Mise en garde pour une protection permanente contre des expositions excessives aux rayons ultra violets UV 1 Ne pas utiliser cet appareil si le bo tier de la lampe n est pas compl tement fix ou si les blindages lentilles ou crans ultraviolets sont endommag s 2 Changer les blindages ou les crans ultraviolets s ils sont visiblement endommag s au point que leur efficacit aient t alt r e par exemple par des fissures ou de profondes gratignures 3 Ne jamais regarder directement la lampe quand celle ci est allum e Instructions pour l installation 1 Laissez un d gagement minimum de 61 cm 24 pouces autour de l entr e d air et de l chappement N utilisez pas l appareil dans des zones basses susceptibles d tre inond es ou dans des zones pouvant tre submerg es sous des eaux profondes et stagnantes 2 L Ecodome ne peut pas tre mont sur un mur ou en t te queue Instructions pour la maintenance 1 D branchez l appareil avant toute intervention de maintenance 2 V rifiez le filtre de l entr e d air et celui de l chappement chaque fois que vous effectuez une op ration de maintenance sur l appareil par exemple lorsque vous changez une lampe Les filtres air doivent tre remplac s lorsqu ils sont visiblement encrass s 3 Vous devez utiliser un filtre air FRAM CA 5056 ou quivalent Les filtres air FRAM CA 5056 sont en vente chez les dist
40. sfare i requisiti delle normative di sicurezza statunitensi ed internazionali Qualsiasi modifica al prodotto potrebbe pregiudicare la sicurezza e rendere il prodotto non conforme agli standard di sicurezza pertinenti Advertencia De Modificaci n Del Producto Los productos de High End Systems est n dise ados y fabricados para cumplir los requisitos de las reglamentaciones de seguridad de los Estados Unidos e internacionales Las modificaciones al producto podr an afectar la seguridad y dejar al producto fuera de conformidad con las normas de seguridad relevantes Important Safety Information Instructions pertaining to continued protection against fire electric shock exposure to excessive ultraviolet UV radiation and injury to persons are found in Appendix A Please read all instructions prior to assembling mounting and operating this equipment Important Informations De S curit Les instructions se rapportant la protection permanente contre les incendies l lectrocution l exposition un rayonnement ultraviolet UV excessif et aux blessures corporelles se trouvent dans l Annexe A Veuillez lire toutes les instructions avant d assembler de monter ou d utiliser cet quipement Ecodome User Manual v Wichtige Sicherheitshinweise Sicherheitsanleitungen zum Schutz gegen Feuer elektrischen Schlag berm ige UV Strahlung und Verletzung von Personen finden Sie in Anhang A Vor der Montage dem Zusamm
41. tions To oil the blower motor 1 Use the tamper proof screwdriver shipped with Ecodome to remove the base clamp 2 Carefully lift the housing and dome from the base and fixture 3 Locate the blower motor see Figure 3 2 4 Oil the blower motor in the holes on each side of the motor see Figure 3 2 You must use 10 to 20 drops of either SAE 10W or 20W non detergent oil ML type or electric motor oil 5 Replace the housing and dome over the base Use the tamper proof screwdriver to tighten the base clamp Figure 3 2 Oiling the blower motor blower motor holes 3 4 Performing Maintenance Ecodome User Manual Ecodome User Manual Important Safety Information A 1 A Appendix A Appendix A Appendix A Appendix A Important Safety Information Important Safety Information Important Safety Information Important Safety Information Conditions of Acceptability for ETL C ETL Recognition of Ecodome Ecodome is an ETL C ETL Recognized Component that is acceptable for use only under the following conditions 1 Ecodome must be installed in accordance with local and national building and electrical codes 2 A suitable mounting site with drainage is provided that does not subject the enclosure to submersion in liquid 3 The model Universal Ecodome is to be used only with HID Lighting Fixture Model Studio Color 575 M Studio Color 575 S Studio Color Studio Spot Stud
42. to High End Systems must be packaged in a suitable manner to ensure the protection of such Product unit or parts and such package shall be clearly and prominently marked to indicate that the package contains returned Product units or parts and with an RMA number Accompany all returned Product units or parts with a written explanation of the alleged problem or malfunction Ship returned Product units or parts to 2227 West Braker Lane Austin TX 78758 USA Note Freight Damage Claims are invalid for fixtures shipped in non factory boxes and packing materials vi Ecodome User Manual Freight All shipping will be paid by the purchaser Items under warranty shall have return shipping paid by the manufacturer only in the Continental United States Under no circumstances will freight collect shipments be accepted Prepaid shipping does not include rush expediting such as air freight Air freight can be sent customer collect in the Continental United States REPAIR OR REPLACEMENT AS PROVIDED FOR UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER HIGH END SYSTEMS INC MAKES NO WARRANTIES EXPRESS OR IMPLIED WITH RESPECT TO ANY PRODUCT AND HIGH END SPECIFICALLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE HIGH END SHALL NOT BE LIABLE FOR ANY INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGE INCLUDING LOST PROFITS SUSTAINED OR INCURRED IN CONNECTION WITH ANY PRODUCT OR CAUSED BY PRODUCT DEFECTS OR THE PAR
Download Pdf Manuals
Related Search