Instruction Manual - Pure n Natural Systems, Inc.
Contents
1. During the dry operation if the room temperature is lower than 10 C 50 F the compressor stops operation and restarts until the room temperature is above 12 C 54 F Optimal operation To achieve optimal performance please note the following Adjust the air flow direction correctly so that it is not directed on people Adjust the temperature to achieve the highest comfort level Do not adjust the unit to excessive temperature levels Close doors and windows on COOL or HEAT modes or performance may be reduced Use TIMER ON button on the remote controller to select a time you want to start your air conditioner Do not put any object near air inlet or air outlet as the efficiency of the air conditioner may be reduced and the air conditioner may stop running Clean the air filter periodically otherwise cooling or heating performance may be reduced Do not operate unit with horizontal louvre in closed position Care and maintenance CARE AND MAINTENANCE Before mainatenance eTurn the system off before cleaning To clean wipe with a soft dry cloth Do not use bleach or abrasives NOTE Power supply must be disconnectd before cleaning the indoor unit CAUTIONS e Acloth dampened with cold water may be used on the indoor unit if it is very dirty Then wipe it with a dry cloth Do not use a chemically treated cloth or duster to clean the unit Do not use benzine thinner polishing powder or simil2. A Caution Do not touch the metal parts of the unit when removing the filter Injuries can occur when handling sharp metal edges Do not use water to clean inside the air conditioner Exposure to water can destroy the insulation leading to possible electric shock When cleaning the unit first make sure that the power and circuit breaker are turned off Do not wash air filter with hot water at more than 40 C 104 F Shake off moisture completely and dry it in the shade Do not expose it directly to the sun it may shrink D Compressor protection The compressor can t restart for 3 4 minutes after it stops Anti cold air Cooling and heating models only The unit is designed not to blow cold air on HEAT mode when the indoor heat exchanger is in one of the following three situations and the set temperature has not been reached A When heating has just started B Defrosting C Low temperature heating e The indoor or outdoor fan stop running when defrosting Cooling and heating models only Defrosting Cooling and heating models only Frost may be generated on the outdoor unit during heat cycle when outdoor temperature is low and humidity is high resulting in lower heating efficiency of the air conditioner During this condition air conditioner will stop heating operation and start defrosting automatically The time to defrost may vary from 4 to 10 minutes according to the outdoor temperature and the amou
3. pictures in this manual are for explanation purpose only Your air conditioner may be slightly different The actual shape shall prevail OPERATING INSTRUCTIONS Indication lamp S a 8H tt CLEAN AIR indication lamp optional Lights up when CLEAN AIR feature is activated and lonizer can generate abundant anions to fill the room with refreshing and natural air p ww AUTO indication lamp Lights up during the Auto operation y OPERATION indication lamp This lamp illuminates when the air conditioner is in operation DIGITAL DISPLAY indication lamp Displays current setting temperature or malfunction codes when the air conditioner is in operation Displays the room temperature under Fan only mode ai 89 jst DEFROST indication lamp for cooling and heating model only This indicator illuminates when the air conditioner starts defrosting automatically or when the warm air control feature is activated in heating operation TIMER indication lamp Lights up during Timer operation Special functions Follow Me function Optional The remote controlserves as aremote thermostat allowing for the precise temperature control atits location Toactivate the Follow Me feature pointthe remote controltowards the unitand press the Follow Me button The remote displayis actual temperature at its location The remote control will sendthis signal tothe air conditionerevery 3 minutesinterval until pressthe Follow Me
4. stop automatically and the air conditioner turns to FAN only mode The compressor will start again when the indoor temperature rises on COOL mode or falls on HEAT mode For cooling and heating models only to the set point 12 TROUBLESHOOTING TIPS T The air conditioner runs Anti mildew function after turning off the unit When turning off the unit under COOL AUTO COOL FORCED COOL and DRY mode the air conditioner will run Anti mildew function for 7 10 minutes if turns off on HEAT mode the unit will continue operating for about 30 seconds at LOW fan speed then stop the operation and turn off the unit automatically Dripping water may generate on the surface of the indoor unit when cooling in a high relatively humidity relative humidity higher than 80 Adjust the horizontal louver to the maximum air outlet position and select HIGH fan speed Heating mode For cooling and heating models only The air conditioner draws in heat from the outdoor unit and releases it via the indoor unit during heating operation When the outdoor temperature falls heat drawn in by the air conditioner decreases accordingly At the same time heat loading of the air conditioner increases due to larger difference between indoor and outdoor temperature If a comfortable temperature can t be achieved by the air conditioner we suggest you use a supplementary heating device 10 Auto restart function 11 12 Power failure during operation wil
5. The design andspecifications are subjectto change without prior notice for product improvement Consultwith the salesagency or manufacturer for details CS047U BP9A3 2020001A4485 20130521 Before using your air conditioner please read this manual carefully and keep it for future reference INVERTER SPLIT TYPE ROOM AIR CONDITIONER ASE a m ere Read This Manual Inside you will find many helpful hints on how to use and maintain your air conditioner properly Just a little preventative care on your part can save you a great deal of time and money over the life of your air conditioner You ll find many answers to common problems in the chart of troubleshooting tips If you review the chart of Troubleshooting Tips first you may not need to call for service CONTENTS SAFETY PRECAUTIONS Wannihig seere a a E E seesaw ce tenas asso en ead tnes dee meaeded eosmoenea 3 G20 16 Ree ee ee ae ee Ie Pee ee re er eee 4 NAMES OF PARTS Indoor MUNIN mormane moea e a a a a oni E E E E A E E 5 CUO UN haar see csctersee ss ys a i i asd ac a nai a Ea AEE AA O EEEa 5 PCG ARO WEAN epee ce pects tcacese rane nes severe usae aren aecgeaseteeueecansd qdanneeneeereccan eedemacsiesdmeceanensensecsouanen 6 OPERATING INSTRUCTIONS Special TUNGHIONS pecs crete cata a tend Seine AE een nd peed Paes omens E E 6 Operating TN UC acres sates ezes sean seccxareutacdavssnreeessaosacexn drewsensaned eeeee nhac ieee neces T Manual operation pce peers tats ee
6. ar solvents for cleaning These may cause the plastic surface to crack or deform Never use water hotter than 40 C 104F to clean the front panel it could cause deformation of discoloration Cleaning the unit wipe the unit with a soft dry cloth only If the unit is very dirty wipe it with a cloth soaked in warm water Cleaning the air filter and air freshening filter A clogged air filter reduces the cooling efficiency of this unit Please clean the filter once every 2 weeks 1 Lift the indoor unit panel up to an angle until it stops with a clicking sound For some models please use suspension bars to prop up the panel 2 Take hold of the handle of the air filter and lift it up slightly to take it out from the filter holder then pull it downwards 3 Remove the AIR FILTER from the indoor unit Clean the AIR FILTER once two weeks Clean the AIR FILTER with a vacuum cleaner or water then dry it up in cool place 4 Remove the Air Freshening Filter from its support frame on some models The optional filter include Plasma Dust Collector Silver lon filter Bio filter Vitamin C filter 3M air purifier filter etc The removing and installation methods are slightly different see the pictures marked and on the left e Clean the air freshening filter at least once a month and replace it every 4 5 months e Clean it with vacuum cleaner then dry it in cool place T CARE AND MAINTENANCE TROUBLESHOOTING TIPS Do n
7. button again If the unitdoes not receivethe Follow Me signal during any 7 minute interval the unit will cancelthe Follow Me mode automatically Anti mildew function Optional When turns off the unit on COOL DRY AUTO Cool mode the air conditioner will continue operating for about 7 10 minutes depending on models at LOW fan speed If turns off on HEAT mode the unit will continue operating for about 30 seconds at LOW fan speed Thiswill help to dry up the condensed water inside the evaporator and prevent the breeding of mildew Under Anti mildew operation do not restart the air conditioner until the unit is completely off 6 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS NOTE This manualdoes not include Remote Controller Operations see the lt lt Remote Controller Instruction gt gt packed with theunit for details Airflow direction control temperature Cooling operation Heating operation Drying operation e Room temperature 17 C 32 C 0 C 30 C 10 C 32 C cae Te 32 F 86 F 50 F 90 F Outdoor temperature 15C 30C 0 C 50 C 15C 50C 5F 1227 5F 86 32 F 1227 For the models with low temperature cooling system NOTE 1 Optimum performance will be achieved within these operating temperatures If air conditioner is used outside ofthe above conditions certain safety protection features might come into operation and cause the unit to function abnormally 2 If the air conditionerrun
8. f the horizontal louver should not be set too small as COOLING or HEATING performance may be impaired due to too restricted air flow area e Do not operate unit with horizontal louver in closed position When the air conditioner is connected to power initial power the horizontal louver may generate a sound for 10 seconds this is a normal operation OPERATING INSTRUCTIONS How the air conditioner works SLEEP operation e 7 hours timer off 1 four 1 hour Set Temperature H Hl hour 1 hour Heating AUTO operation When you set the air conditioner in AUTO mode it will automatically select cooling heating cooling heating models only or fan only operation depending on what temperature you have selected and the room temperature The air conditioner will control room temperature automatically round the temperature point set by you If the AUTO mode is uncomfortable you can select desired conditions manually SLEEP operation When you push SLEEP button on remote controller during cooling heating cooling amp heating models only or AUTO operation the air conditioner will automatically increase cooling or decrease heating 1 C 2 F per hour for the first 2 hours then hold steady for the next 5 hours after that it will switch off This characteristic maintains both enery saving and comfort in night operation DRYING operation The fan speed will be automatically controlled under dry operation
9. hildren aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision DISPOSAL Do not dispose of this product as unsorted municipal waste Collection of such waste separately for special treatment is necessary It is prohibited to dispose of this appliance in domestic household waste For disposal there are several possibilities A The municipality has established collection systems where electronic waste can be disposed of at least free of charge to the user B When buying a new product the retailer will take back the old product at least free of charge C The manufacturer will take back the old appliance for disposal at least free of charge to the user D As old products contain valuable resources they can be sold to scrap metal dealers Wild disposal of waste in forests and landscapes endangers your health when hazardous substances leak into the ground water and find their way into the food chain SAFETY PRECAUTIONS To prevent injury to the user or other people and property damage the following instructions must be followed Incorrect operation due to ignoring of instructions may cause harm or damage The seriou
10. l stop the unit completely For the unit without Auto restart feature when the power restores the OPERATION indicator on the indoor unit starts flashing To restart the operation push the ON OFF button on the remote controller For the unit with Auto restart feature when the power restores the unit restarts automatically with all the previous settings preserved by the memory function For some models the machine is special designed with Auto restart function for the open angle of the horizontal louver Power failure during operation or pressing the ON OFF button on the remote controller will stop the unit completely When the power restores or pressing the ON OFF button on the remote controller again the unit restarts automatically with all the previous settings including the open angle of the horizontal louver by the memory function So we strongly suggest thatthe open angle of the horizontal louver should not be settoo small in case the condensed water forms and drops from the horizontal louver Press the AUTO COOL button under the front panel and the open angle of the horizontal louver will be restored to the standard angle when the condensed water forms on the horizontal louver Lightning ora car wireless telephone operating nearby may cause the unit to malfunction Disconnect the unit with power and then re connect the unit with power again Push the ON OFF button on the remote controller to restart operation The protection of outdoor low te
11. ly otherwise it might cause discomfort or cause uneven room temperatures Adjust the horizontal louver using the remote controller Adjust the vertical louver manually To set the vertical air flow Up Down direction Perform this function while the unit is in operation Use the remote controller to adjust the air flow direction The horizontal louver can be moved at a range of 6 for each press or swing up and down automatically Please refer to the REMOTE CONTROLLER OPERATION MANUAL for details To set the horizontal air flow direction left right Move the vertical louver manually to adjust the air flow in the direction you prefer IMPORTANT Before adjusting the vertical louvers the supply power must be disconnected For some models the vertical louver can be adjusted by using the remote controller Please refer to the REMOTE CONTROLLER OPERATION MANUAL for details A CAUTION e Do not operate the air conditioner for long periods with the air flow direction set downward in cooling or dehumidifying mode Otherwise condensation may occur on the surface of the horizontal louver causing moisture to drop on to the floor or on furnishings e Do not move the horizontal louver manually unless it is necessary Always use the remote controller e When the air conditioner is started immediately after it was stopped the horizontal louver might not move for approximately 10 seconds e Open angle o
12. mperature on some models The protection of outdoor low temperature can be activated only inthe HEATING mode The unit will stop operating and display P3 on the LCD window of the indoor unit when the outdoor temperature is or lower than 5 F 15 C for one hour but the indoor unit in this situation can still receive the signal from the remote controller The unit will restart automatically with all the previous settings preserved by the memory function when the outdoor temperature is or higher than 11 F 12 C for 10 minutes and the compressor stop operating for more than one hour or when the outdoor temperature is or higher than 41 F 5 C for 10 minutes TROUBLESHOOTING TIPS Troubleshooting guide If one of the following faults occurs stop the air conditioner immediately disconnect the power and then connect it in again If the problem still exists disconnect the power and contact the nearest customer service center OPERATION indicator or other indicators continue flashing Fuse blows frequently or circuit breaker trips frequently Trouble Other objects or water fall into the air conditioner The remote controller won t work or works abnormally If one of the following code appears on the display area E0 E1 E2 E3 or PO P1 P2 P3 Unit does not Wait for power to be restored start Unit may have become unplugged Check that plug is securely in wall receptacle Fuse may have blown Replace the fuse Replace the ba
13. ns et ection pee seer ee 7 Airflow direction control scjcscesgtesaaeiecacdanssadvsesacdniecenstnasenisinnsa a eusata vette aos Tateaeenie Rates 8 How the air conditioner WOFKS 000 ccc cc cece cece cece eee e ee ee een eea eee eee eeee seca eee ese eases eseeseeseeeeeeeaeeaeeaeeneees 9 CARE AND MAINTENANCE Before maintenance ccccccccccccceceeceececcecceeececeeseeeeeeeseeceeaececeesueeeseeseeseeaeeeseeseeeeseeseesueaesaegas 10 Cleaning the TUR inasertienteaateatainnnssnadceatneryomusenatadnuatsauussaeaus E E E E a E R 10 Cleaning the air filter and air freshening filter ccccecceecceecceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeaeesaeeseees 10 Replacement of the air filter and air freshening filter cccccecccecceeece cece eeeeeeeeeeeeeeaeeceeenees 11 Preparation for extended NON OPCNAllON x icici ccs sc cdnnscanseccadensenevicdacanescevsencaecans se saedscensaseadsnsanecens 11 Pre season WAS SC OMe ros cta eons ectenc unde sdb inoue Seeualneat sma owbieeaeaent ast diate ease teens esa conned one 11 TROUBLESHOOTING TIPS Normal function OF the air COMCIEIOMEGN sv ceccsiirs fs ceciievstns cutee in fovecaninatendnsediniaaauvaeeseaeainnausdviaedudedivanuades 12 Troubleshooting guide peccacstenstn cone cuntecsessansnttnoncecsteacdvasausensen douthananiseumaasantmidenctaseaedesaasosseesediaureed 14 When using this air conditioner in the European countries please read the following information This appliance can be used by c
14. nstallation of this unit Contact an authorized service technician for repair or maintenance of this unit This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the air conditioner SAFETY PRECAUTIONS CAUTION S Never actuate any switches with a wet hand It may cause an electric shock Never use the device for any other purpose than the intended use Never place food precision instruments plants animals paint etc on the unit Do not expose plants or animals directly to the air flow Never clean the air conditioner with water Never use combustible cleaning agents as these could cause a fire or deformation Never place any burning objects close to the device if they could be directly affected by the emitted air Never step onto the outdoor device and never place anything on it Never use an unsteady or rusty base Never install the air conditioner in places where combustible gas can be emitted Emmitted gas may collect and cause an explosion Never allow the air conditioner to run for too long with the doors or windows open or if the humidity is very high e f the air conditioner is to be used in conj
15. nt of frost built up on the outdoor unit Awhite mist coming out from the indoor unit e Awhite mist may generate due to a large temperature difference between air inlet and air outlet on COOL mode in an indoor environment that has a high relative humidity A white mist may generate due to moisture generated from defrosting process when the air conditioner restarts in HEAT mode operation after defrosting Low noise of the air conditioner You may hear a low hissing sound when the compressor is running or has just stopped running It is the sound of the refrigerant flowing or coming to a stop You can also hear a low squeak sound when the compressor is running or has just stopped running This is caused by heat expansion and cold contraction of the plastic parts in the unit when the temperature is changing e A noise may be heard due to louver restoring to its original position when power is turned on Dust is blown out from the indoor unit This is a normal condition when the air conditioner has not been used for a long time or during first use of the unit A peculiar smell comes out from the indoor unit This is caused by the indoor unit giving off smells permeated from building material from furniture or smoke The air conditioner turns to FAN only mode from COOL or HEAT For cooling and heating models only mode When indoor temperature reaches the temperature setting on air conditioner the compressor will
16. ot touchthe Plasma DustCollector Normal function of the air conditioner Filter within 10 minutes after opening the front panel itmay cause anelectric shock 5 Install the air freshening filter back into position Air freshening filter The following events may occur during normal operation 1 Protection of the air conditioner 6 Insert the upper portion of air filter back into the unit taking care that the left and right edges line up correctly and place filter into position Replacement of air filter and air frenshing filter 1 Remove the air filter 2 Remove the air frenshing filter 3 Install a new air frenshing filter 4 Reinstall the air filter and securely close the front panel Preparation for extended non operation If you plan to idle the unit for a long time perform the following 1 Clean the indoor unit and filters 2 Operate the fan for about half a day to dry the inside of the unit 3 Stop the air conditioner and disconnect power 4 Remove the batteries from the remote controller The outdoor unit requires periodic maintenance and cleaning Do not attempt to do this yourself Contact your dealer or service provider Pre season inspection Check that the wiring is not broken off or disconnected e Clean the indoor unit and filters e Check that the air filter is installed Check if the air outlet or inlet is blocked after the air conditioner has not been used for a long time
17. s for a long timein cooling mode and the humidity is high over 80 condensed water may drip out of the unit Please sets the vertical air flow louver to its maximum angle vertically tothe floor and set HIGH fan mode Suggestion For the unit adopts anElectric Heater whenthe outside ambient temperature is below 0 C 32 F we strongly recommend you to keep the machine plugged inorder to guarantee it running smoothly Manual operation Units are equipped with aswitch to run emergency operation mode It can be accessed by opening the front panel This switch is used for manual operation in case the remote controller fails to work or maintenance necessary NOTE The unit mustbe turned offbefore operating the manualcontrol button Ifthe unit is operational continue pressing the LS 4 manual control button until the unitis off Open and lift the front panel up to an angle until it remains fixed with a clicking sound One press of the manual control switch will Panel lead to the forced AUTO operation If press the switch twice within five seconds the unit will operate under forced COOL operation Close the panel firmly to its original position CAUTION e This switch is used for testing purposes only You had better not choose it e To restore the remote controller operation o AUTO COO use the remote controller directly Manual switch Vertical louver Adjust the air flow direction proper
18. sness is classified by the following indications WARNING This symbol indicates the possibility of death or serious injury A CAUTION This symbol indicates the possibility of injury or damage to property E Meanings of symbols used in this manual are as shown below Strictly prohibited Be sure to follow the instructions WARNING S e Do not extend the cable and never use multiple plugs A poor electrical connection poor insulation or voltage which is higher than permitted can cause fire Do not expose your body directly to the cool air for prolonged period Never poke fingers sticks or other objects in the air inlet and outlet vents e Never attempt to repair relocate modify the air conditioner yourself Always contact your service partner if it requires Never pull the plug out by pulling on the cable Hold the plug firmly and pull it out of the plug socket otherwise there is a risk of damaging the cable e Do not operate your air conditioner in a wet room such as a bathroom or laundry room Remove all dirt from the power plug and plug it firmly Soiled plugs can cause fire or an electric shock In the event of any abnormalities such as smell of burning immediately swithch off the device and pull the plug Contact your service partner Always switch off the device and pull the plug before you start to clean it Use specified power cord Contact the authorized installer for i
19. ttery Battery in Remote controller may have been exhausted The time you have set with timer Wait or cancel timer setting is incorrect Inappropriate temperature Set temperature correctly For setting detailed method please refer to Using remote control section models only Air filter is blocked Clean the air filter 0 the air filter room very well while air flowing Doors or Windows are open Close the doors or windows out from the air Air inlet or outlet of indoor or outdoor unit has been blocked Clear obstructions away first then restart the unit If the trouble has not been corrected please contact a local dealer or the nearest customer service center Be sure to inform them of the detailed malfunctions and unit model conditioner Compressor 3 minutes protection has been activated Notes Do not attempt to repair the unit yourself Always consult an authorised service provider 4
20. unction with other heaters the air should be refreshed periodically otherwise there is a risk of lack of oxygen e Always pull out the power plug if the unit is not going to be used for any lengthy period of time Collections of dust can cause fire e Always switch off the air conditioner and pull out the power plug during a storm Electrical parts may get damaged e Check that the drainage line is correctly connected If not water will escape Check that the condensation water can run off unhindered It may cause water damage if the condensation water cannot run off properly The air conditoner must be earthed in accordance with the local codes e For electrical safety purposes we recommend that you install an earth leakage circuit breaker e f the power cord is damaged it must be replaced by the manufacturer its service agent or similary qualified persons in order to avoid a hazard NAMES OF PARTS NAMES OF PARTS Indoor unit NOTE The indoor unityou purchased would like one ofthe following Thereis a slightly difference on frontpanel and display window butthe features arethe same Outdoor unit Air inlet rear Indoor unit 1 Front panel 2 Aijr inlet 3 Horizontal air flow grille 4 Vertical air flow louver 5 Display panel 6 Connecting pipe 7 Drain hose Outdoor unit 8 Connective cable 9 Connective pipe 10 Stop valve NOTE All the
Download Pdf Manuals
Related Search