5. using the slam cot fastener
Contents
1. GFERNO USERS MANUAL When It s Critical SLAM SAFETY LOCK Ca SLAM Cot Fastener July 2014 Pub N MU 049 H Read this manual carefully and retain it for future reference Slam Cot Fastener Warning This manual contains general information on the use operation and maintenance of this product Instructions contained in this manual do not cover every single application and operation Safety and proper use of this product depend on the user acting responsibly Safety information is provided for the user and only ensures the minimum level necessary to avoid injury to operators and patients Appropriate training is recommended for staff who use this product before each actual application Keep this manual safe for future reference and pass it on to new users Additional free copies are available upon request from Ferno Washington Italia Customer Relations Rights Information contained in this manual is the property of Ferno Washington Italia s r l Via Benedetto Zallone 26 40066 Pieve di Cento BO Italy Ferno Washington Italia s r l reserves all rights related to images and illustrations This manual may not be reproduced in whole or part without the express authorization of Ferno Washington Italia s r l Copyright Ferno Washington Italia s r l All rights reserved Ferno Washington Italia s r l Via Benedetto Zallone 26 40066 Pieve di Cento BO ITALY Internet www ferno it E2. 2 Notes on the vehicle If the SLAM Cot Fastener is mounted on the ambulance floor ensure that it is not installed near oxygen tubes or fuel lines and that no holes are made in the structure of the vehicle during installation 4 3 Parts supplied Each model hasa SLAM Cot Fastener and front anchoring Please refer to chapter 3 Description of the SLAM Cot Fastener 4 4 Tools and installation elements needed A drill with 7 mm and 9 mm bits A Phillips screwdriver An adjustable wrench Pliers M8 and M6 bolts of various lengths Nuts and washers for M8 and M6 screws Low strength threadlocker 24 diameter wrench 4 5 Anchoring the SLAM Cot Fastener Depending on the type of installation you will need a 26S stretcher a 26 P stretcher a 5026 stretcher or a 4051 or a 4052 trolley Identify where the stretcher or trolley will be positioned in the ambulance and mark the position of the 4 anchorage points of the SLAM Cot Fastener on the floor Remove the SLAM Cot Fastener and make 4 holes 9 mm in diameter in correspondence with the points marked The SLAM Cot Fastener is fixed to the floor using four M8 countersunk hex head screws nuts and washers screws not included Use rubber washers locknuts or medium or low strength threadlocker If the SLAM Cot Fastener is fixed to the floor of the ambulance or on a loading surface the lower part of the floor or the metal sheet of the loading surface must
3. have a steel counterplate minimum 3 mm thick and 200 mm x 160 mm in size Apply medium or low strength threadlocker to the screw thread For further information contact Ferno Washington Italia Technical Assistance Service 4 6 Anchoring the SLAM 26 fork This operation must be performed after the operations described in paragraphs 4 5 and 4 8 Attach the 26S or 26P stretcher to the SLAM Cot Fastener and ensure that the attaching mechanism has clicked into place fully and correctly Bring the fork into contact with the transversal tube of the stretcher and move it at least 10 mm in the opposite direction to the SLAM figure 5 Mark the 5 anchorage points on the floor Remove the fork and make 4 holes with a 9 mm diameter and one hole with a 7 mm diameter in correspondence with the points marked the 4x9 mm diameter holes in correspondence with the 4 holes of the 8 mm diameter fork and the 7 mm diameter hole in correspondence with the 6 mm diameter fork Ferno Washington Italia s r l MU 049 H July 2014 The fork is anchored to the floor using four M8 screws and one M6 screw their relative nuts and washers screws not supplied Use rubber washers locknuts or medium or low strength threadlocker Place two steel counterplates with a minimum thickness of 4 mm and at least 80 mm x 80 mm in size in the lower part of the floor or the metal sheet of the loading surface for the screws shown in figure 6 r I _
4. mail info ferno it Telephone sccasoncateecaseeeniecs Rain pE 39 0516860028 Lui 39 0516861508 Ferno Washington Italia s r l MU 049 H July 2014 Slam Cot Fastener Chapter Paragraph Page Chapter Paragraph Page 1 SAFETY INFORMATION 4 5 USING THE SLAM COT FASTENER 12 1 1 Safety warnings 4 5 1 Before use 12 ae as cate sia MIO FA Soiano Fi 5 2 Locking and unlocking the stretcher or Ca uscor Al Een spac pas trolley with the SLAM Cot Fastener 12 a i 6 MAINTENANCE 13 1 3 Conformity to current regulations 5 coi Vaiano 13 1 4 Information labels 5 6 2 Hygienic treatment 14 hea PRO LIOSSAE 2 6 2 1 Disinfection 14 1 6 Risks of infection 5 6 2 2 Cleaning 14 COLERA eek Ne RE 6 6 3 Safety and functional check 14 SOSIO aD i 7 ACCESSORIES AND RELATED PRODUCTS 15 eee ONE i 8 TECHNICAL SUPPORT AND SERVICE __ 16 o gt Oper Sali i 8 1 Technical Support 16 3 DESCRIPTION OF THE SLAM COT 8 2 Services and Training 16 FASTENER 6 9 WARRANTY 16 3 1 General Features 6 oo 9 1 Warranty Conditions 16 3 2 SLAM Cot Fastener disclaimer 7 9 2 Disclaimers 17 3 3 SLAM 26 components 7 9 3 Warranty Requests 17 3 4 SLAM 5026 EFX Components 7 9 4 Complaints 17 3 5 SLAM 4050 Components 7 9 5 Authorization for Returns 17 4 INSTALLING THE SLAM COT FASTENER 8 10 TRAINING RECORD 18 4 1 Notes on installation 8 11 MAINTENANCE RECORD 18 4 2 Notes on the vehicle 8 4 3 Parts supplied 8 4 4 Tools and installation elements needed 8 4 5 Anchoring the SLAM Cot
5. prior approval by Ferno W Italia s r l Products returned for commercial reasons i e for reasons that do not derive from defects of conformity will only be accepted after they have been checked by specialized Ferno W Italia s r l staff 17 18 Slam Cot Fastener 10 TRAINING RECORD Ferno Washington Italia s r l MU 049 H July 2014 Slam Cot Fastener Product user and maintenance manual needed for the safe operation efficiency and reliability of the product and to render warranty conditions valid MU 049 H July 2014 Ferno Washington Italia s r l Via Benedetto Zallone 26 40066 Pieve di Cento BO ITALY Internet www ferno it E mail info ferno it TEISPHNONC iaia 39 0516860028 Fl 39 0516861508 Ferno Washington Italia s r l MU 049 H July 2014 19
6. the interface is there If it is missing contact Ferno Washington Italia Customers Services Figure 13 single bolt interface Ferno Washington Italia s r l MU 049 H July 2014 Slam Cot Fastener 4 10 Anchoring the SLAM CUSTOM PWR forks This operation should take place after those described in paragraph 4 5 Attach the CUSTOM PWR stretcher to the SLAM Cot Fastener and ensure that the attaching mechanism has clicked into place fully and correctly O des Bring the fork into contact with the carter and move it at G p FASTENER least 10 mm in the opposite direction to the SLAM Mark the 6 anchorage points on the floor The fork is anchored to the floor using six M6 screws their relative nuts and washers screws not supplied Use rubber washers locknuts or medium or low strength threadlocker Figure 14 Distance 10 mm 4 11 Testing phase Once the SLAM Cot Fastener has been assembled whichever model is used load the stretcher 26S 26P or series 5026 or the trolley series 4050 onto the ambulance and carry out loading and unloading tests e Load the stretcher or trolley and lock it to the Always use threadlocker when indicated in this users manual SLAM Cot Fastener Check that the stretcher or Follow the installation instructions in the users manual trolley is locked correctly enclosed with the product in order to ensure safety e Unlock the stretcher or trolley by pressing the red compli
7. Fastener 8 4 6 Anchoring the SLAM 26 fork 8 4 7 Anchoring the SLAM 4050 and SLAM 5026 EFX forks 9 4 8 Assembling the SLAM 26 rear interface 10 4 9 Assembling the bolt for series 4050 trolleys 10 4 10 Anchoring the SLAM CUSTOM PWR forks 11 4 11 Testing phase Ferno Washington Italia s r l MU 049 H July 2014 11 Slam Cot Fastener 1 SAFETY INFORMATION Read this User Manual carefully It is an integral part of the device and must always be readily available For your own personal safety and that of the patient please observe the following Before each use check that the device is working properly by following the indications in this manual see chapter 6 paragraph 6 3 Safety and functionality checks Inorderto avoid infection and or bacterial contamination carefully follow the instructions in chapter 6 paragraph 6 2 Hygienic treatment 1 1 Safety warnings Warning notices indicate a potentially hazardous situation which if not avoided could result in injury Improper use of the SLAM Cot Fastener can cause damage and or injury Use the SLAM Cot Fastener for its intended purpose as described in this manual Untrained operators may injure themselves and or cause damage or injury Only trained personnel should be allowed to use the SLAM Cot Fastener Unauthorized modifications may cause serious damage injury or unforeseen operative problems Do not modify or alter the SLAM Cot Fastener in any
8. alia s r l MU 049 H July 2014 Slam Cot Fastener 3 2 SLAM Cot Fastener disclaimer 3 4 SLAM 5026 EFX Components The SLAM Cot Fastener in its available models has been exclusively designed for use with the stretchers and trolleys listed in paragraph 3 1 General Features There is no guarantee that the SLAM Cot Fastener is suitable for stretchers or trolleys other than those indicated For conditions of warranty please refer to chapter 9 Warranty 3 3 SLAM 26 components Figure 3 SLAM 5026 EFX components a SLAM Cot Fastener b Front anchorage with dual hook 3 5 SLAM 4050 Components Figure 2 SLAM 2 components 6 a SLAM Cot Fastener b Rear interface c Front anchorage with dual hook Figure 4 SLAM 4050 components a SLAM Cot Fastener b Single bolt interface c Front anchorage with dual hook Ferno Washington Italia s r l MU 049 H July 2014 Slam Cot Fastener 4 INSTALLING THE SLAM COT FASTENER 4 1 Notes on installation Installation of the SLAM Cot Fastener requires professional knowledge of how a road ambulance is built The SLAM Cot Fastener has been designed to be installed with steel counterplates placed below the surface on which the SLAM Cot Fastener is installed the floor of an ambulance or loading surface etc If the vehicle in which the SLAM Cot Fastener is installed does not have the counterplates required they must be installed by qualified technicians 4
9. ance The SLAM Cot Fastener conformity unlock button on the SLAM Cot Fastener figure 15 declaration released by Ferno Washington Italia and proceed to unload depends on correct installation of the product according to instructions Ferno Washington Italia declines all responsibility if the SLAM Cot Fastener is incorrectly installed e Repeat these operations several times to ensure everything is working correctly Red unlock button for stretchers trolleys Figure 15 Red unlock button for stretchers trolleys on the SLAM Cot Fastener Ferno Washington Italia s r l MU 049 H July 2014 12 Slam Cot Fastener 5 USING THE SLAM COT FASTENER 5 1 Before use The operator must have carefully read and understood the information contained in this manual and in the user manual of the stretcher or trolley to be used with the SLAM Cot Fastener before operation The SLAM Cot Fastener must be installed firmly and correctly by a specialized technician see chapter 4 paragraph 4 1 Notes on installation Ensure that the SLAM Cot Fastener is installed correctly Ensure that the anchor bolts are regulated properly Follow the instructions in chapter 6 paragraph 6 3 Safety and Functional Check Improper use of the SLAM Cot Fastener may cause damage and or injury Use the SLAM Cot Fastener for its intended purpose and as described in this manual 5 2 Locking and unlocking the stretcher or trolley with t
10. ately Contact Ferno Washington Italy Customer Relations to request new labels page 2 Prodotto da Ferno Washington Italia S r l Via B Zalone 26 40066 Pieve di Cento Italy Tel 051 6860028 Fax 051 6861508 C u Ses OSN Figure 1 Main label Ferno Washington Italia s r l MU 049 H July 2014 Slam Cot Fastener 1 5 Symbol Glossary These symbols are shown on the SLAM Cot Fastener and in this manual CE This product meets European Union Standards Shows the red SLAM unlock button 1 6 Risks of infection To reduce the risk of exposure to blood born infectious diseases like HIV 1 or hepatitis scrupulously follow the instructions in this manual while using the SLAM Cot Fastener and make sure it undergoes hygienic treatment Slam Cot Fastener 2 OPERATOR SKILLS AND TRAINING 2 1 Operator ability Operators who use the SLAM Cot Fastener must Be familiar with procedures for moving the patient Be able to assist the patient Have understood the procedures described in this manual Have taken part in a specific training course on how to use the device correctly Be familiar with the device its features and all the accessories used 2 2 Training For correct training users must Read this manual carefully for additional copies contact Ferno Washington Italia s r l Customer Relations Follow a Training Program to use the SLAM Cot Fastener correctly and sa
11. bearings brushes lubricants tracks and belts etc parts potentially subject to oxidation or corrosion copper or metal alloy elements electrical and mechanical apparatus and batteries External finishes gel coat resin paint powder coating decals ribbons lettering etc are guaranteed for 90 days Repairs are carried out by specialized technical staff at the Ferno Washington Italia s r l headquarters in Via Zallone 26 40066 Pieve di Cento BO or at the Customer s premises if approved by Ferno Washington Italia Customer Relations Technical support carried out at the Customer s premises must be approved and will include partial reimbursement of expenses sustained that will be documented upon request For info on the cost of technical support contact Ferno W Italia s r l Technical Support Department Repairs are guaranteed for 6 months from the date of completion This warranty applies only if the product is used according to the user manual supplied Improper or careless use will render this warranty void The warranty begins on the day on which the product is sent by Ferno W Italia s r l and does not cover delivery costs Ferno W Italia s r l is not responsible for damage in transport or for damage caused by improper use of the product Products that do not have the original Ferno trademark sold by Ferno W Italia s r l are covered by the product manufacturer s original warranty Ferno W Italia s r l will not
12. cialized Ferno technician If the device is used heavily the SLAM Cot Fastener should undergo maintenance more frequently by authorized Ferno personnel Repairs must be carried out by a specialized Ferno technician with original spare parts We recommend the user follows the maintenance schedule below Maintenance Schedule Each Use Disinfection Cleaning Inspecting Safety and functional check Contact Ferno Washington Italia for information on disinfection and cleaning disinfecting products Improper use and improper maintenance may cause damage accidents and or injury Carry out maintenance as described in this manual Only use original spare parts Maintenance and repairs must be carried out only by a Ferno technician As Needed Each Month Table I User maintenance schedule Ferno Washington Italia s r l MU 049 H July 2014 13 Slam Cot Fastener 6 2 Hygienic treatment 6 2 1 Disinfection 1 Clean the surfaces of the SLAM Cot Fastener with disinfectant after every use Use a non abrasive surface disinfectant 2 Do not immerse the SLAM Cot Fastener in disinfectant 3 Check that there are no signs of wear or damage during disinfection 4 Dry with a cloth Ensure that all the components of the device are completely dry before using them again 5 Suitable gloves are recommended during disinfection e g disposable gloves or household gloves 6 2 2 Cleaning 1 Clean the surfaces of t
13. extend a warranty beyond the product manufacturer s warranty period Ferno W Italia s r l will not be held responsible for products manufactured by others The warranty will not apply in the case of Failure to observe instructions for use Wrong usage Inappropriate use or handling Repairs to the device by unauthorized personnel Damage in transport due to improper packaging when returned by the user Lack of maintenance Failure to use original parts In cases not covered by the warranty Ferno W Italia will not be responsible for transport costs for sending and returning the product Ferno Washington Italia s r l MU 049 H July 2014 9 2 Disclaimers Ifa product is defective Ferno W Italia s r l will repair or replace it or refund the cost price at its discretion Ferno W Italia s r l will not be responsible for refunding more than the cost of the product The buyer accepts these terms in lieu of all damages Ferno W Italia s r l does not make any other express or implicit guarantees nor does it make any guarantee as to the merchantability or suitability for particular ends of its product or the products of others In the case of infraction of the limited warranty legal procedures must be archived within a year of the date on which an infraction was or should have been discovered Ferno W Italia s r l reserves the right to cancel the warranty on products sold If labels or pla
14. fely Practice with the SLAM Cot Fastener and its accessories before using it in real situations Carefully record the training sessions with the SLAM Cot Fastener on the form enclosed with this manual chapter 10 Training record Untrained personnel may cause serious damage or injury to themselves and to patients Only expert properly trained staff should be allowed to use the SLAM Cot Fastener 2 3 Operator skills Operators must be able to ensure their own safety and the safety of patients while using this product Operators must know how to use the device and the various system components safely 3 DESCRIPTION OF THE SLAM COT FASTENER 3 1 General Features The SLAM device is a SLAM Cot Fastener for Ferno stretchers to be fitted on the ground or on ambulance loading surfaces It is supplied in various models in order to fit several stretchers and loading systems The following models are available e SLAM 26 for 26 S and 26P stretchers SLAM 5026 EFX for 5026 series and CUSTOM M stretchers e SLAM 4050 for 4051 and 4052 trolleys e SLAM CUSTOM PWR for CUSTOM PWR Improper use of the SLAM Cot Fastener can cause damage and or injury Use the SLAM Cot Fastener for its intended purpose and as described in this manual If the SLAM Cot Fastener is not assembled according to the instructions in this manual can it cause serious damage and or injury to operators and patients Ferno Washington It
15. he SLAM Cot Fastener How to lock the stretcher or trolley to the SLAM Read the stretcher or trolley user manual on how to load correctly Load the stretcher or trolley into the ambulance and guide it in the direction of the front anchoring elements forks in the case of the SLAM 26 and SLAM 4050 Align the bolt positioned in the rear part of the stretcher or trolley with the SLAM guide channel figure 16 Slide the stretcher or trolley so that the bolt is inserted into the snaplock of the guide channel The bolt will automatically activate the locking mechanism so that the stretcher or trolley is locked firmly Snaplock Guide channel Figure 16 Stretcher trolley lock How to unlock the stretcher or trolley from the SLAM Read the stretcher or trolley user manual on how to unload correctly To unlock the stretcher or trolley from the SLAM press the red unlock button on the SLAM figure 17 and proceed to unload Red stretcher trolley unlock button Figure 17 SLAM red stretcher trolley unlock button Ferno Washington Italia s r l MU 049 H July 2014 Slam Cot Fastener 6 MAINTENANCE 6 1 Routine Maintenance The SLAM Cot Fastener should be maintained regularly Preventative maintenance inspections and repairs must be carried out exclusively by Ferno or by personnel expressly authorized by the manufacturer The SLAM Cot Fastener must undergo preventative maintenance at least once a year by a spe
16. he SLAM Cot Fastener with a cloth warm water and non abrasive detergent Do not immerse the SLAM Cot Fastener in water 3 Use a soft brush to remove any marks if necessary taking care not to remove labels 4 Dry with a cloth 5 Do not wash with pressurized water 6 Suitable gloves are recommended during cleaning e g disposable gloves or household gloves Steam or high pressure water penetrates the joints and may cause corrosion or remove lubricant Do not use high pressure water or steam to clean disinfect the SLAM Cot Fastener 6 3 Safety and functional check This inspection is to look for any problem that may compromise the integrity or correct functioning of the SLAM Cot Fastener The safety and functional check must be carried out monthly or more frequently if the product is used heavily Technical maintenance personnel should carry out the following checks e Are all components present e Does the snaplock mechanism close perfectly when the locking bolt is inserted e Does the front bar for SLAM 26 SLAM 4050 and SLAM 5026 fit perfectly into the fork e Are the SLAM Cot Fastener and the forks fixed firmly and correctly to the ambulance e Are the forks bent cracked or are there evident signs of wear and tear or damage e Is the single bolt interface installed on the series 4050 stretcher figure 13 If signs of wear damage malfunction or attrition are discovered during this test and i
17. ies 5126 stretchers as shown in figure 8 Figure 8 Distance of approx 180 mm 10 Slam Cot Fastener 4 8 Assembling the SLAM 26 rear interface Figure 9 Position of the rear interface on the stretcher The bar must be positioned on the middle axis of the stretcher figure 9 The plastic bearing must be inserted in the central crossbar and the clamps must be positioned and fixed as shown as in figures 10 and 11 Figure 10 Detail showing the front and central clamps Figure 11 Detail showing the rear clamp with single bolt Place the low strength threadlocker on the screw thread The screws must be fixed so that the clamps are parallel to the upper bar Adjust the height of the bolt to maintain the interspace shown in figure 12 between the head of the bolt and the lower part of the SLAM Cot Fastener plaque Tighten the bolt in position using the return ring nut Figure 12 Adjusting the height of the single bolt As the return ring nut has a self locking ring there is no need for threadlocker Regulate the SLAM Cot Fastener as shown in this manual Incorrect regulation can cause problems when the stretcher is locked and unlocked 4 9 Assembling the bolt for series 4050 trolleys The series 4050 trolley which does not come with a reinforced single bolt interface figure 13 must be adapted in order to be used with the SLAM Cot Fastener Before assembling the SLAM Cot Fastener check that
18. lol_ Mai ot ri LA a DES errs 0 Pe _ pt eE a Md CF 1 r pi T a M m k pre i as A et na E y Pa y F li fu peas des HT r url fi Figure 5 Position of the fork in contact with the transversal tube of series 26 stretcher Figure 6 Fastenings for which the counterplates are needed Ferno Washington Italia s r l MU 049 H July 2014 Slam Cot Fastener 4 7 Anchoring the SLAM 4050 and SLAM 5026 EFX forks This operation should take place after those described in paragraph 4 5 Attach the series 5026 stretcher or series 4050 trolley to the SLAM Cot Fastener and ensure that the attaching mechanism has clicked into place fully and correctly Bring the fork into contact with the transversal tube of the stretcher and move it at least 10 mm in the opposite direction to the SLAM Mark the 6 anchorage points on the floor The fork is anchored to the floor using six M6 screws their relative nuts and washers screws not supplied Use rubber washers locknuts or medium or low strength threadlocker Place four steel counterplates with a minimum thickness of 4 mm and at least 80 mm x 80 mm in size in the lower part of the floor or the metal sheet of the loading surface for the screws shown in figure 7 Figure 7 Fastenings for which the counterplates are needed Wa rning ensure that there is a distance of approximately 180 mm between the two end sections of the anchorage system for ser
19. nd is aligned with the upper edge of the SLAM e Wait approximately 24 hours before use so that the adhesive sticks perfectly Ferno Washington Italia s r l MU 049 H July 2014 15 16 Slam Cot Fastener 8 TECHNICAL SUPPORT AND SERVICE Check regularly that the strip has no attrition and change it if it is worn or damaged 8 1 Technical Support For technical support repairs and further information contact Ferno Washington Italia s r l Via B Zallone n 26 40066 Pieve di Cento BO Italy tel 39 0516860028 fax 39 0516861508 Email info ferno it 8 2 Services and Training For information on the use of the SLAM Cot Fastener and to plan training courses contact Ferno Washington Italia s r l Via B Zallone n 26 40066 Pieve di Cento BO Italy tel 39 0516860028 fax 39 0516861508 Email info ferno it 9 WARRANTY 9 1 Warranty Conditions Ferno products are guaranteed free from manufacturing defects for 24 months from the date shown on the Ferno W Italia s r l delivery note Ferno Washington Italia parts have a 12 month warranty During the warranty period all parts with properly ascertained manufacturing defects will be repaired and or replaced not including labor costs or transfer transport and packaging costs The warranty does not cover consumables or components subject to wear associated with normal product use any parts typically subject to sliding or rolling friction ball
20. nspection the device must be taken out of use immediately Contact the Ferno Washington Italia Technical Support Service immediately Ferno Washington Italia s r l MU 049 H July 2014 Slam Cot Fastener 7 ACCESSORIES AND RELATED PRODUCTS Part No Description SLAM 26 COT FASTENER FOR 26 S AND 26P STRETCHERS WITH FRONT ANCHORING KIT SLAM 5026 EFX COT FASTENER FOR SERIES 5026 AND CUSTOM M STRETCHERS WITH FRONT ANCHORING KIT SLAM 4050 COT FASTENER FOR 4051AND 4052 TROLLEYS WITH FRONT ANCHORING KIT SLAM CUSTOM PWR COT FASTENER FOR CUSTOM PWR STRETCHERS WITH FRONT ANCHORING KIT 25 0331 001 WEDGE KIT FOR SLAM 5026 EFX RAMP SLAM 26 FASTENER FOR 26 S STRETCHERS WITH FRONT ANCHORING KIT To assemble the ramp wedge kit code 25 0331 001 see instructions for correct assembly of the ramp for the SLAMS5026 EFX Cot Fastener 7 z CA s SAFETY ee AE al Figure 18 Ramp wedge kit Figure 19 Ramp wedge kit installed For better hold of the 5126EL stretcher anti fall system to the SLAM Cot Fastener apply a self adhesive non slip strip to the SLAM figure 20 Figure 20 Self adhesive non slip strip Instructions for applying the self adhesive non slip strip e Clean the surface of the SLAM Cot Fastener to which the strip will be applied carefully with acetone thinner or alcohol e Cut the strip if necessary to obtain a length of around 130 mm Apply the strip so that it fits perfectly to the surface a
21. tes showing the manufacturer s trademark serial number or registration number have been erased or removed If the product has been altered or repaired or if work has been carried out without authorization by Ferno W Italia s r l or its personnel If the product has not been used according to the instructions supplied or for purposes other than that for which it was designed According to paragraph 9 1 Warranty Conditions Under no circumstances will Ferno W Italia s r l be held responsible for direct or indirect damage caused by use other than that described in the user manual and for which the product was designed 9 3 Warranty Requests If you suspect that you have received a defective product contact Ferno Customer Relations immediately A representative will deal with your complaint Obtain authorization from Ferno Customer Relations before sending products to Ferno W Italia s r l Ferno Washington Italia s r l MU 049 H July 2014 Slam Cot Fastener 9 4 Complaints Any complaints must be communicated to the vendor or to Ferno W Italia s r l Customer Relations within 5 days of receipt of the product or discovery of the alleged defect Complaints or controversies regarding a single product do not exonerate the buyer from the obligation of receiving and paying for other products in the same order unless otherwise agreed with the seller 9 5 Authorization for Returns No product will be accepted without
22. way Any damage to the SLAM Cot Fastener may alter its performance and safety Inspect the SLAM Cot Fastener frequently and especially before and after each use Do not use the SLAM Cot Fastener if it appears worn or damaged Repairs carried out by technicians or workshops not authorized by Ferno W Italia will render any type of warranty void and may make any operation involving the SLAM Cot Fastener dangerous Improper operation can cause damage and or injury Carry out maintenance as described in this manual Non original spare parts may cause damage Only use original Ferno spare parts Ferno Washington Italia s r l MU 049 H July 2014 1 2 Important Important notices emphasize important usage or maintenance information Important Do not use high pressure water or steam to clean the SLAM Cot Fastener High pressure water and steam may cause the SLAM Cot Fastener to corrode 1 3 Conformity to current regulations This product has been designed and built by Ferno Washington Italia s r l in conformity with safety regulations contained in Directive 93 42 EEC class I regarding medical devices and with EN 1789 1999 A1 2003 regulations Medical vehicles and their equipment Road ambulances CE 1 4 Information labels The information and safety labels provide important information of which the user must be aware Read and follow the instructions on the labels Replace worn or damaged labels immedi
Download Pdf Manuals
Related Search