Operating instructions
Contents
1. 099 L08742 EW501 17 30 01 2015 User manual Xbutton administration ew 4 5 button administration The Xbutton is used to identify the user to the end device The user specific rights are stored on the Xbutton One user can have multiple Xbuttons with different rights A Xbutton however can only be assigned to one user 4 5 1 Create Xbutton Initial situation Program has been started e Connect a new Xbutton to the programming device me Ifthe Xbutton is not yet known to the system the following dialog opens Unknown Xbutton Do you want to add it to the database Confirm by clicking Yes Dal The Permissions dialog opens Permission Explanation Activate correction mode By selecting this option the correction mode is activated for the user Block change of wire feed speed Selecting this option will prohibit the user from changing the wire feed speed Block change of voltage correction Selecting this option will prohibit the user from changing the voltage correction Block change of arc dynamics Selecting this option will prohibit the user from changing the arc dynamics Block change of operating mode Selecting this option will prohibit the user from changing the operating mode Block change of welding type Selecting this option will prohibit the user from changing the welding type Block change of superPuls Selecting this option will prohibit the user from activating superPuls Block JOB switching Selecting2. Operating instructions ewm f A UN CEN Xbutton Tool 099 L08742 EW501 Observe additional system documents 30 01 2015 Register now For your benefit transformer and rectifier f 3 Years Years 24 hours 7 days Jetzt Registrieren _ ewm warranty ii und Profitieren www ewm group com General instructions Read the operating instructions li The operating instructions provide an introduction to the safe use of the products e Read the operating instructions for all system components e Observe accident prevention regulations e Observe all local regulations e Confirm with a signature where appropriate In the event of queries on installation commissioning operation or special conditions at the installation site or on usage please contact your sales partner or our customer service department on 49 2680 181 0 A list of authorised sales partners can be found at www ewm group com Liability relating to the operation of this equipment is restricted solely to the function of the equipment No other form of liability regardless of type shall be accepted This exclusion of liability shall be deemed accepted by the user on commissioning the equipment The manufacturer is unable to monitor whether or not these instructions or the conditions and methods are observed during installation operation usage and maintenance of the equipment An incorrectly performed installation can result in material damage
3. this option will prohibit the user from changing the welding JOB Block JOB reset Selecting this option will prohibit the user from resetting the welding JOB Restrict program selection Selecting this option will prohibit the user from selecting certain welding programs Restrict program sequence Selecting this option will prohibit the user from accessing certain welding program sequences and changing their parameters Block change of configuration parameters Selecting this option will prohibit the user from changing the configuration parameters Block program 0 Selecting this option will prohibit the user from accessing program 0 Block welding start Selecting this option will prohibit the user from starting the welding JOB ie By selecting the Show reserves option further permissions are shown which are currently not activated in the software They can be used as reserves for software updates e Activate inactivate the required permissions for the Xbutton or select a template from the Use template selection box Assign a name to the Xbutton using the New Xbutton name input field 18 099 L08742 EW501 30 01 2015 ewe User manual Xbutton administration Select the user to be assigned to the Xbutton from the Name selection box e Click the Write permission button on the button bar to save the changes e Click the Home page button on the button bar to dismiss the changes 4 5 2 Edit Xbutton Initi
4. 0 www ewm rathenow de info ewm rathenow de EWM AG Rudolf Winkel Stra e 7 9 37079 G ttingen Tel 49 551 3070713 0 Fax 20 www ewm goettingen de info ewm goettingen de EWM AG Sachsstra e 28 50259 Pulheim Tel 49 2234 697 047 Fax 048 www ewm pulheim de info ewm pulheim de EWM AG Eiserfelder Stra e 300 57080 Siegen Tel 49 271 3878103 0 Fax 9 www ewm siegen de info ewm siegen de Q Sales and Service International EWM HIGHTEC WELDING GrnbH WiesenstraBe 27b 4812 Pinsdorf Austria Tel 43 7612 778 02 0 Fax 20 www ewm austria at info ewm austriaat EWM HIGH TECHNOLOGY Kunshan Ltd Yanshan Road Kunshan New amp Hi tech Industry Development Zone Kunshan City Jiangsu Post code 215300 People s Republic of China Tel 86 512 57867 188 Fax 182 www ewm cn info ewm cn info ewm group cn Tt Plants CH Branches 099 L08742 EW501 30 01 2015 Forststra e 7 13 56271 M ndersbach Germany Tel 49 2680 181 0 Fax 144 www ewm group com info ewm group com Appendix A Overview of EWM branches Technology centre TEAMWELDER s r o T 9 kv tna 718 31 407 53 Ji kov Czech Republic Tel 420 412 358 551 Fax 504 www teamwelder cz info teamwelder cz EWM HIGHTEC WELDING GmbH Sales and Technology Centre Draisstra e 2a 69469 Weinheim Tel 49 6201 84557 0 Fax 20 www ewm weinheim de info ewm weinheim de EWM Schwei technik Handels G
5. 10 Click Next r Geratetreiberinstallations Assistent Willkommen Mit diesem Assistenten k nnen Sie Sofiwaretreiber installeren die zum ordnungsgem en Ausf hren einiger Computergerate erforderlich sind Klicken Sie auf Weiter um den Vorgang fortzusetzen Weiter gt Abbrechen Figure 3 12 Fertigstellen des Assistenten Die Software f r de Hardwareger te wurde nicht aktualisiert weil sie nicht besser als die zurze installierte Software ist Treibemame Status wi FTDICDM Driver Packa Betriebsbereit W FTDICDM Driver Pacha Betnebsberet Faser Ae Click Finish The software will be installed Figure 3 13 099 L08742 EW501 30 01 2015 ewmm Administrator manual Update 3 4 Update The update procedure is similar to the installation with the exception that you have to deselect the Database initialisation option in the available components list Xbutton tool software E Database initialisation _ Microsoft NET Framework C Wibu Runtime v5 2 vw USB Serial Driver by FTDI Ga If you fail to deselect Database initialisation and the installation starts the existing database will be deleted and all data will be permanently lost 099 L08742 EW501 11 30 01 2015 User manual ewm Xbutton Tool screen layout 4 User manual 4 1 Xbutton Tool screen layout For a clearer overview the screen display is divided into three main sections in this man
6. Block JOB switching Selecting this option will prohibit the user from changing the welding JOB Block JOB reset Selecting this option will prohibit the user from resetting the welding JOB Restrict program selection Selecting this option will prohibit the user from selecting certain welding programs Restrict program sequence Selecting this option will prohibit the user from accessing certain welding program sequences and changing their parameters 099 L08742 EW501 30 01 2015 ewin User manual Template administration Permission Explanation Block change of configuration parameters Selecting this option will prohibit the user from changing the configuration parameters Selecting this option will prohibit the user from accessing program 0 Block welding start Selecting this option will prohibit the user from starting the welding JOB Block program 0 me By selecting the Show reserves option further permissions are shown which are currently not activated in the software They can be used as reserves for software updates e Activate inactivate the required rights e Click the Save as template button on the button bar The new template is saved in the system and is immediately available by clicking the Templates folder button 099 L08742 EW501 1 5 30 01 2015 4 4 4 4 1 4 4 2 4 4 2 1 16 User manual ewm User administration User administration In the user administration you can create a
7. a FirmlD E2FESB Installation Language English DBFileName Enter database file for Users Figure 3 4 e Click Next The software will be installed win Xb utton Tool Installer Language English DI Select the installation type Initial installation User defined Installation complete 2 Eu 22 nina mann nn zen IE wi Figure 3 5 e Click Close 099 L08742 EW501 7 30 01 2015 Administrator manual e Wibu Runtime installation 3 2 Wibu Runtime installation To start Xbutton Tool Wibu Runtime has to be installed If not installed yet the installation will start automatically Willkommen beim Setup von CodeMeter Runtime Kit v5 20a Setup instalkert CodeMeter Runtime Kit v5 20a auf Ihrem Computer Klicken Sie auf Weiter um fortzufahren oder auf Abbrechen um Setup zu beenden Click Next Installationsart W hlen Sie eine Installationsart und einen Zielordner aus Installieren f r Benutzerkonto CodeMeter Runtime Kit v5 20a ist nur f r Ihr Benutzerkonto verf gbar Sie ben tigen keine lokalen Administratorberechtigungen F r alle Benutzer auf diesem Computer installieren CodeMeter Runbme Kit v5 20a wird standardm ig in einem Einzelbenutzerordner instalbert und ist f r alle Benutzer verf gbar Der Zielordner kann ge ndert werden Daf r ben tigen Sie lokale Administratorberechtigungen aurick Weter _ Figure 3 7 Select the In
8. al situation Program has been started e Connect a Xbutton which has already been assigned rights to the programming device The Permissions dialog opens Permission Activate correction mode Block change of wire feed speed Block change of voltage correction Block change of arc dynamics Block change of operating mode Block change of welding type Block change of superPuls Block JOB switching Block JOB reset Restrict program selection Restrict program sequence Block change of configuration parameters Block program 0 Block welding start Explanation By selecting this option the correction mode is activated for the user Selecting this option will prohibit the user from changing the wire feed speed Selecting this option will prohibit the user from changing the voltage correction Selecting this option will prohibit the user from changing the arc dynamics Selecting this option will prohibit the user from changing the operating mode Selecting this option will prohibit the user from changing the welding type Selecting this option will prohibit the user from activating superPuls Selecting this option will prohibit the user from changing the welding JOB Selecting this option will prohibit the user from resetting the welding JOB Selecting this option will prohibit the user from selecting certain welding programs Selecting this option will prohibit the user from accessing certain welding program sequences an
9. and injure persons as a result For this reason we do not accept any responsibility or liability for losses damages or costs arising from incorrect installation improper operation or incorrect usage and maintenance or any actions connected to this in any way EWM AG Dr G nter Henle Str 8 D 56271 M ndersbach Germany The copyright to this document remains the property of the manufacturer Reprinting including extracts only permitted with written approval Subject to technical amendments ewmm Contents Brief description 1 Contents COMTCINS aane E E E hun EEE E E 3 RA E 4 Zale Poer dospio EE 4 KE e Ee 4 2 2 1 VT eu e 4 2 2 2 VE ele EE 4 2 3 System reouirements sessar aia a Eai aa a aaa a aai adaa 4 2 3 1 Client system reoulrements A 4 Gelee ET ee EE 4 2 4 1 Standard SCOPE Of Supply eek 4 2 4 2 Required accessories and licenses eeeccceeeesceeeeeenneeeeeenaeeeeeeaaeeeeeeaaeeeseeaaeeeeeeaeeeeeeaas 4 Administrator OT 2022222 an RARER RAAEN NRAN 5 Bel WAStAN ATOM ET 5 32 Wibu R time instalation sieren uaine aneia naa aaa e aaa eaS aaa AAN 8 33 FTDI USB driver Imnstallaton nenn 9 TE HE EEN 11 Hetzt 12 41 Xbutton Tool screen layout en 12 4 2 System role administration eee ee eeee cece eect ee ee ce eeeeeeeeaeeeeaaeeeeaee ceases seaeeseaaeseeeeeseaeeeeaeeseeeseeneees 13 4 2 1 Create system Folleg csavisi deni een seien alien 13 4 2 2 Clean Systemi Toles eisidein een 13 4 3 Template admini
10. d changing their parameters Selecting this option will prohibit the user from changing the configuration parameters Selecting this option will prohibit the user from accessing program 0 Selecting this option will prohibit the user from starting the welding JOB me By selecting the Show reserves option further permissions are shown which are currently not activated in the software They can be used as reserves for software updates e Activate inactivate the required permissions for the Xbutton or select a template from the Use template selection box Assign a name to the Xbutton using the New Xbutton name input field Select the user to be assigned to the Xbutton from the Name selection box e Click the Write permission button on the button bar to save the changes e Click the Home page button on the button bar to dismiss the changes 099 L08742 EW501 30 01 2015 19 User manual ewmm Xbutton administration 4 5 3 Inactivate Xbutton This function is used to temporarily neutralise a Xbutton All permissions are reset to not authorised and the user entry on the Xbutton is deleted Initial situation Program has been started e Connect a Xbutton which has already been assigned rights to the programming device The Permissions dialog opens Select the user with the name unallocated user from the Name selection box e Click the Write permission button on the button bar to save th
11. e changes e Click the Home page button on the button bar to dismiss the changes mee The inactivated Xbutton is stored in the Unallocated folder until it is allocated again to a user 4 5 4 Overview of unallocated Xbuttons Initial situation Program has been started e Click the Unallocated Xbuttons button on the button bar The dialog opens the list of all inactivated Xbuttons which are assigned to the unallocated user in the system 20 099 L08742 EW501 30 01 2015 5 5 1 Appendix A Overview of EWM branches Headquarters EWM AG EWM AG Dr G nter Henle Stra e 8 56271 M ndersbach Germany Tel 49 2680 181 0 Fax 244 www ewm group com info ewm group com LX Production Sales and Service EWM AG Dr G nter Henle Stra e 8 56271 M ndersbach Germany Tel 49 2680 181 0 Fax 244 www ewm group com info ewm group com EWM HIGH TECHNOLOGY Kunshan Ltd 10 Yuanshan Road Kunshan New amp Hi tech Industry Development Zone Kunshan City Jiangsu Post code 215300 People s Republic of China Tel 86 512 57867 188 Fax 182 www ewm cn info ewm cn info ewm group cn Sales and Service Germany EWM AG Sales and Logistics Centre S lzerstra e 20a 56235 Ransbach Baumbach Tel 49 2623 9276 0 Fax 244 www ewm ransbach baumbach de info ewm ransbach baumbach de EWM AG Sales and Technology Centre Gr nauer Fenn 4 14712 Rathenow Tel 49 3385 49402 0 Fax 2
12. ide sufficient server capacity and ensure data backup Welding supervisor Based on their relevant vocational or further training expertise experience and knowledge of the different welding processes the welding machine operator welding engineer or welding supervisor is able to perform the task of monitoring and analysing the welding process data as assigned to them They are also able to operate the computers and access the operating panel System requirements Client system requirements Compatibility IBM compatible Hard disk 500 MB hard disk space or more Connections 2 USB 2 0 ports or more Operating system Windows 7 or later Software NET 4 0 part of the installation if required Scope of supply Standard scope of supply The standard scope of supply includes e USB interface with Xbutton adapter e Software Licensing dongle e 10 Xbuttons Required accessories and licenses Xbutton is supplied with a dongle with an activated license to operate the Xbutton Tool If you intend to operate Xnet and Xbutton at the same time please contact EWM AG to transfer the license to the existing Xnet dongle 099 L08742 EW501 30 01 2015 ewin Administrator manual Installation 3 Administrator manual 3 1 Installation Initial situation The dongle is connected to the computer e On the dongle open the directory XbuttonTool Release e Start the Setup bat installation file by double clicking it A promp
13. ill be deleted from the database 099 L08742 EW501 13 30 01 2015 4 3 4 3 1 14 User manual ewm Template administration Template administration Templates are used to define frequently used groups of user rights to facilitate the assignment of those rights to the users Create template Initial situation Program has been started e Connect a new Xbutton to the programming device me Ifthe Xbutton is not yet known to the system the following dialog opens Unknown Xbutton Do you want to add it to the database Confirm by clicking Yes errr SSS e Ge Figure 4 3 e Click the Permissions tab The button permissions will be displayed Permission Explanation Activate correction mode By selecting this option the correction mode is activated for the user Block change of wire feed speed Selecting this option will prohibit the user from changing the wire feed speed Block change of voltage correction Selecting this option will prohibit the user from changing the voltage correction Block change of arc dynamics Selecting this option will prohibit the user from changing the arc dynamics Block change of operating mode Selecting this option will prohibit the user from changing the operating mode Block change of welding type Selecting this option will prohibit the user from changing the welding type Block change of superPuls Selecting this option will prohibit the user from activating superPuls
14. ll the users who are to be assigned Xbuttons Create user Initial situation Program has been started Hm User administration Not connected to Xnet Figure 4 4 e Click the Create user button on the button bar At the end of the user table a new user is inserted with the first name NewFirstname and name NewName default values To change these default values click the corresponding field Kaz Figure 4 5 Edit user Edit user name NOTE m A user name can be edited only as long as no Xbutton has been created for this user Initial situation Program has been started and the user has been created e Inthe user table click the First name or Name field The data record selected will be highlighted in blue e Activate the edit mode by pressing F2 e Change the data record as required e Save your changes by pressing Enter e Dismiss your changes by pressing Esc 099 L08742 EW501 30 01 2015 ewmm User manual User administration 4 4 2 2 User system role allocation me A system role can be allocated to a user only as long as no Xbutton has been created for this user Initial situation Program has been started and the user has been created e Inthe System role column click the arrow next to the user you want to edit The system roles created will be displayed e Select the required system role e Save your changes by pressing Enter e Dismiss your changes by pressing Esc
15. mbH Karlsdorfer Stra e 43 88069 Tettnang Tel 49 7542 97998 0 Fax 29 www ewm tettnang de info ewm tettnang de EWM Schwei technik Handels GmbH Pfaffensteig 17 89143 Blaubeuren Tel 49 7344 9191 75 Fax 77 www ewm blaubeuren de info ewm blaubeuren de EWM Schwei technik Handels GmbH Heinkelstra e 8 89231 Neu Ulm Tel 49 731 7047939 0 Fax 15 www ewm neu ulm de info ewm neu ulm de EWM HIGHTEC WELDING UK Ltd Unit 2B Coopies Way Coopies Lane Industrial Estate Morpeth Northumberland NE61 6JN Great Britain Tel 44 1670 505875 Fax 514305 www ewm morpeth co uk info ewm morpeth co uk EWM HIGHTEC WELDING Sales s r o Prodejn a poradensk centrum Tyr ova 2106 256 01 BeneSov u Prahy Czech Republic Tel 420 317 729 517 Fax 712 www ewm benesov cz info ewm benesov cz More than 400 EWM sales partners worldwide 21
16. s atosan ee an 14 4 3 1 Cult 14 4 4 User dministration nenne re era ee 16 4 4 1 ET 16 4 4 2 EOM USEN aussen a Da ah ee ren 16 442 1 Ge TE En EE 16 4 4 2 2 User system role allocation ce eecceeeeeneeeeeenneeeeeeaeeeseeaeeeeeeaeeeeeeaeeeeeeaas 17 4 5 button administration cccceceeecescce cece eeeeeeeeaeeeeeeeeeeeeeaaaeceeeeeeeseceaeaeceeeeeeesceeaeaeeeeeeeeeseesuceeeeees 18 4 5 1 Crate ADUNO EEN 18 4 5 2 Edit XDUTOMi EE 19 4 5 3 IMACTIVALE XDUTLON nes 20 4 5 4 Overview of unallocated Xbuttons 20 Appendix A EEERN ENNEN NEEN EENEEEAENEEEEA SEENEN EENS REENEN EES 21 5 1 Overview of EWM branches ssssssssssinsssttnsttttssttttntt trte rttr Ann tE ASSE EE ENEE EEES S EAEAN EEEn nE EEEn mEnE Eeee 21 099 L08742 EW501 3 30 01 2015 2 2 1 2 2 2 2 1 2 2 2 2 3 2 3 1 2 4 2 4 1 2 4 2 Overview ewm Brief description Overview Brief description Xbutton is a system to intelligently control access rights for EWM welding machines equipped with an Expert 2 0 control By programming small and handy storage chips for recognition users can be assigned different usage rights The Xbutton Tool is used to manage the storage chips and users Audience IT administrator Based on their training and experience the IT administrators are able to provide for the system requirements and work environment including the technical equipment required for operating the software They are also able to prov
17. stall for all users of this computer installation mode Click Next a RAN TASTE DEE AEE lern o Dieses Feature installert das CodeMeter Runtime Kit auf Ihrem Computer Diese Funktion erfordert 31MB auf der Festplatte Es sind 2 von 2 untergeordneten Funktionen gew hlt die 15M8 auf der Festplatte erfordern Durchsuchen Qur chsetzen _ Datentragervermendung Figure 3 8 Click Next 099 L08742 EW501 30 01 2015 ewmm Administrator manual FTDI USB driver installation Klicken Sie auf Installeren um mit der Installation zu beginnen Klicken Sie auf Zur ck um die Installationseinstellungen anzuzeigen oder zu ndern Klicken Sie auf Abbrechen um das Setup zu beenden Figure 3 9 e Click the Install button The software will be installed CodeMeter Runtime Kit v5 20a Setup abgeschlossen Klicken Sie auf Fertig stellen um das Setup zu beenden Build 1458 Figure 3 10 e Click Finish The installation is complete 3 3 FTDI USB driver installation The FTDI USB driver is a required component to control the Xbutton USB interface If not installed yet the installation will start automatically r FTDI CDM Drivers FTDI CDM Drivers Click Extract to unpack version 2 12 00 of FT e Windows driver package and launch the installer Figure 3 11 e Click Extract 099 L08742 EW501 9 30 01 2015 Administrator manual FTDI USB driver installation
18. t opens to check whether NET4 0 is installed on the system EE C Windows system32 cmd exe Siom E t P WI T F Figure 3 1 Press any key to close the prompt The installation welcome page opens a Xnet setup ewm XbuttonTool npa Language English e Select the installation type Initial installation User defined Figure 3 2 e Select the User defined installation mode 099 L08742 EW501 5 30 01 2015 Administrator manual ewm Installation e Click the Install button The selection dialog with the available components opens a Component manager gt m ewm XbuttonTool g vw Xbutton tool software ri Database initialisation Microsoft NET Framework vw Wibu Runtime v5 2 vw USB Serial Driver by FTDI Back Figure 3 3 Component Explanation Xbutton Tool software The Xbutton Tool software Database initialisation New creation of the database Any existing database including its data will be overwritten Microsoft NET Framework Microsoft NET Framework Wibu Runtime Driver for the dongle and software based activation USB Serial Driver by FTDI Driver for the Xbutton USB interface e Click Next The parameter editor opens 6 099 L08742 EW501 30 01 2015 ewm Administrator manual Wibu Runtime installation FRE 4 Database file DBFileName C Users Public Documents Xbutton Tool DB Xbutton cxml EWM Xnet WebServer WebServerlP localhost BU Firm dat
19. ual navigation bar dialog and button bar User administration 1 zlo zlo Figure 4 1 Item Description 1 Navigation bar 2 Dialog 3 Button bar 12 099 L08742 EW501 30 01 2015 ew User manual System role administration 4 2 System role administration System roles are used to define groups of users A system role represents an assigned function or access right When logging on to an Expert 2 0 control the system role will be displayed as well 4 2 1 Create system roles Initial situation Program has been started e Click the Settings button in the navigation bar The Settings dialog opens e Settings g g T s a Sy SI Figure 4 2 Clicking the arrow on to the System roles selection field will open the system roles that have already been created e Inthe System roles selection field enter the name of the new system role e Save your changes by pressing Enter 4 2 2 Clean system roles Xbutton is supplied with a number of predefined system roles Their colour correlates to the available Xbuttons As long as no data records have been created these system roles can be deleted if they do not match your needs For this reason it is recommended to set the system roles before you start programming the Xbuttons Initial situation Program has been started and the user has opened the Settings menu e Click the Clean system roles button on the button bar All system roles not currently used w
Download Pdf Manuals
Related Search