DWC-D562D(IR) - Digital Watchdog
Contents
1. DW INSTALLATION Included with Value Line Indoor Dome Camera 3 Second Video Jack 4 Mounting Screws 3 1 User Manual 2 Mounting Template CUR e gt EN lin RA f M ET o PD79 EASY INSTALLATION Install the Enclosure Cover To install the dome cover align the dome cover with the camera base and push until it securely snaps into place __ Remove the Dome Cover Before you can mount or adjust your Value Line Indoor Dome Camera you must remove the dome cover Insert a coin or screwdriver in the slot on the dome cover then twist to pry the dome cover from the camera base Dome Cover Camera Base DW BASE INSTALLATION 1 Pull wires through and make connections 2 Adjust the camera s 3 Axis Gimbal Refer to page 10 Use mounting template to focus and zoom See pages 11 12 for mount camera with dry wall mounts and wood details screws 3 Press the joystick button to open the OSD menu 4 Snap the dome cover onto the camera base Push the joystick left right up or down to navigate the OSD menu See pages 13 24 for details CONNECTING TO MONITORS 12VDC 24VAC gt cco CCTV Monitor2. Monitor m Power connection 12VDC 24 VAC Dual Voltage Auto polarity detection and protection m All cameras are equipped with a second video output on the camera s Control Board for easy on site configuration 10 DW ADJUSTING THE CAMERA Zoom Tele E Wide Focus Far a Near Loosen the zoom and focus handles by rotating them counter clockwise Adjust the field of view by moving the handle to the RIGHT tele to zoom in or to the LEFT wide to zoom out Adjust the focus the same way as described above AFTER the desired zoom position is established Once the desired adjustments have been made please tighten the handles back by turning them clockwise 11 ADJUSTING THE 3 AXIS GIMBAL The Gimbal mechanism yields maximum rotation and placement as shown below Rotation 360 Panning 360 12 MODULE OSD MENU EXPOSURE COLOR DW DAY NIGHT LENS MANUAL DC BACKLIGHT OFF BLC HME D WDR AGC OFF LOW MID HIGH HIGHEST 2D DNR OFF LOW MIDDLE HIGH EXIT JUMP SAVE amp EXIT EXIT WB MODE AWC ATW MANUAL PUSH RED GAIN 0 255 BLUE GAIN 0 255 COLOR MODE NORMAL COOL WARM EXIT JUMP SAVE amp EXIT EXIT DAY amp NIGHT AUTO COLOR B amp W NIGHT C 0 100 NIGHT A 0 100 EXIT JUMP SAVE
3. PRIVACY MASE 1 DW You can hide some parts of the screen for privacy masking A total of 8 dfferent privacy masking zones are available MASK 1 MASK 8 OFF ON Select ON or OFF for each mask If ON is selected you can set the area to be masked and the shape and color of the mask START POINT Select the START POINT to adjust the size of the privacy zone L_TOP Left Top R_TOP Right Top L BOT Left Bottom R_BOT Right Bottom MODIFY After selecting the START POINT you can modify the size of the privacy zone by moving the joystick POSITION Move the privacy zone by moving the joystick COLOR SET Privacy Zones can be set with 8 different colors GRAY BLACK WHITE RED GREEN BLUE MAGENTA CYAN 21 ul SET UP SEI TITLE OFF ON If ON is selected you can display the camera title on the screen CLR Clear the title POS Select position of the title on the screen USERA TITLE OLD Hat DPC Dead Pixel Cancellation OFF AUTO Dead Pixel Cancellation automatically removes defective pixels in real time If AUTO is selected you can define the following DPC ABHTO WHITE THR Cancels the white defective pixels BLACK THR Cancels the black defective pixels iT i DPC LEVEL Adjusts the sensitivity level of the dead pixel cit cancellation Note Adjust the WHITE THR BLACK THR and DPC LEVEL at the same time 22 DW TS SET UP BEI MON
4. If ON is selected the camera provides a color burst signal in night mode If OFF no color burst signal is provided COLOR B amp W Adjusts the light level at which the camera switches from day color to night B amp W mode The higher the number the lower the light level B amp W COLOR Adjusts the light level at which the camera switches from night B amp W to day color mode This number should be lower than the value of COLOR B amp W above SMART IR ON OFF If using IR LEDs ON is recommended READ TIME Time interval delay before switching from day mode to night mode It is adjustable from seconds to 12 seconds EX IR INT AUTO EXT If using IR LEDs built into the camera select AUTO If using external IR LEDs separately select EXT Color will be reduced in low light conditions This level cannot be adjusted when 2D DNR is ON Edge sharpness will be reduced in low light conditions This level cannot be adjusted when 2D DNR is ON Exit the OSD after saving the current settings Exit the OSD without saving DW i i FUNCTION EU MIRROR OFF FUMCT ION MIRROR Flips the image horizontally pst re SHARPNESS 0 30 Sets the image sharpness The higher the number the sharper the image GAMMA 0 45 0 6 1 0 Controls the output signal level The higher the MANUAL setting the darker the dark colors will be 0 45 is default SLC Side Light Compensation OFF ON Increases brightn
5. amp EXIT EXIT FUNCTION MOTION PRIVACY MIRROR MIRROR OFF SHARPNESS 0 30 GAMMA MANUAL 0 45 0 60 1 0 SLC OFF ON NIGHT UP OFF ON EXIT JUMP SAVE amp EXIT EXIT r TITLE OFF ON r DPC SET OFF AUTO MONITOR MODE1 MODE2 LANGUAGE ENGLISH 92 xc fai A sc A DEUTSCH FRENCH ITALIAN RUSSIAN SPANISH DUTCH OSD COLOR BLUE GREEN CYAN RED MAGENTA YELLOW PURPLE GRAY r COMMUNICA OFF ON FACTORY SET NO YES EXIT JUMP SAVE amp EXIT EXIT r AREA SET AREAS 1 4 OFF ON SENSITIV 1 30 SHOW INDI OFF ICON TRACE EXTER OUT OFF ON EXIT JUMP SAVE amp EXIT EXIT SAVE amp EXIT EXIT r MASK1 OFF ON MASK2 OFF ON MASK3 OFF ON MASK4 OFF ON MASK5 OFF ON MASK6 OFF ON MASK7 OFF ON MASK8 OFF ON EXIT JUMP SAVE amp EXIT EXIT 13 EXPOSURE LENS MANUAL MANUAL mode supports the fixed board lens or the manual iris lens DC DC mode supports the auto iris varifocal lens Note Both MANUAL and DC mode have FOCUS TARGET You can adjust the focus by finding the highest number on the FOCUS TARGET See page 11 for Focus information LEN amp DC LEMS MANDAL DC AUTO Li FOCUS TARGET 00600 FOCUS TARGET 6000 ELC levels and DC levels are adjustable The higher the number the brighter the images E Shutter sets the shutter speed levels from
6. 1 60 to 1 100000 AUTO and DC AUTO are the default shutter speeds for both indoor and outdoor use Select 1 100FLC to run camera in flickerless mode 14 DW EXPOSURE BACKLIGHT OFF BLC BACKLIGHT COMPENSATION HME D WDR Select MANUAL or SMART SMART is recommended 5 If MANUAL is selected you can adjust the BLC level in f four areas of the scene Top Bottom Left Right bra Increase the BLC level where you want e a to make the image brighter If SMART is selected the camera will automatically adjust the BLC zone BLC levels to choose from include LOWEST LOW MID HIGH BL EL bet ra HIGHLIGHT MASKING EXPOSURE f HME masks highlights to allow objects to appear clearly on the sie screen If ON is selected HME levels are adjustable The lower the number the darker the masking areas LU SMI LE DIGITAL WIDE DYNAMIC RANGE STA D WDR is one of the backlight compensation functions You can adjust the D WDR level from 0 20 The lower the number the brighter the backlight 15 amp 5 EXPOSURE LEPC AGC Auto Gain Control OFF LOW MID HIGH HIGHEST 2D DNR Digital Noise Reduction OFF LOW MIDDLE HIGH EXIT JUMP SAVE amp EXIT EXIT 16 AGC enhances picture brightness in low light conditions A higher AGC setting makes the image brighter however it could cause an increase in noise 2D DNR reduces noise on the screen in low
7. Out of Focus VIDEO Check the clear dome cover and the lens for dirt or fingerprints Use a soft cloth and gently clean Check the lens manual focal and zoom adjustment A field test monitor is recommended 25 WARRANTY INFORMATION Digital Watchdog referred to as the Warrantor warrants the Digital Watchdog Camera against defects in materials or workmanship as follows LABOR For the initial two 2 years and one 1 year on IR LED from the original purchase date if the camera is determined to be defective the Warrantor will repair or replace the unit with a new or refurbished product at its option at no charge PARTS In addition the Warrantor will supply replacement parts for the initial two 2 years and one 1 year on IR LED To obtain warranty or out of warranty service please contact a Technical Support Representative at 1 866 446 3595 Monday through Friday from 8 30AM to 8 00PM Eastern Standard Time A purchase receipt or other proof of the original purchase date is required before warranty service is rendered This warranty only covers failures due to defects in materials and workmanship which arise during normal use This warranty does not cover damage which occurs in shipment or failures which are caused by products not supplied by the Warrantor or failures which result from accident misuse abuse neglect mishandling misapplication alteration modification faulty installation set up adjustments imprope
8. in Weight 0 54 Ibs Specification is subject to change without prior notice 29 DIGITAL D WATCHDOG Everything s Digital DIGITAL MEMO D SWAT DOC Everything s Digital DN coss Everything s Digital 5436 W Crenshaw St Tampa FL 33634 Tel 866 446 3595 Fax 813 888 9262 www Digital Watchdog com technicalsupport dwcc tv Technical Support Hours Monday Friday 8 30am to 8 00pm Eastern Standard Time
9. 60H Sharp CCD Total Pixels 1020 H x 507 V 520K Pixels Scanning System 2 1 Interlace Frequency 15 734KHz H 59 95Hz V Synchronization Internal Horizontal Resolution 650 TV Lines Color 700 TV Lines B W Minimum Illumination F1 2 30IRE 0 3 Lux Color F1 2 80IRE 0 0 Lux B A S N Ratio 520 AGC off Video Output CVBS 1 0Vp p 75 Focal Length 2 8 11mm Lens Type DC Auto Iris IR Distance 85ft Range Lens MANUAL DC 000 100 Backlight Compensation Auto Gain Control OFF BLC HME DIGITAL WDR OFF LOW MID HIGH HIGHEST White Balance AWC ATW MANUAL PUSH Color Mode NORMAL COOL WARM Day and Night AUTO COLOR B amp W Mirror OFF MIRROR 28 DW Sharpness 0 30 Gamma MANUAL 0 45 0 60 1 00 Side Light Compensation OFF ON 0 30 Night Up OFF ON Motion Detection OFF ON 4 Programmable Zones Privacy Zones OFF ON 8 Programmable Zones Title OFF ON Up to 16 Characters Dead Pixel Cancellation OFF AUTO Communication Protocol PELCO D Operating Temperature 10 C 55 C 14 F 131 F Operating Humidity Less than 90 Non Condensing Storage Temperature 20 C 70 C 4 F 158 F Power Requirement Dual DC12V amp AC24V Power Consumption DC12V 1 6W LED ON 4 3W AC24V 1 9W LED ON 4 0W Housing Material Plastic Dome Cover Material Polycarbonate Dimensions 20118 X 82 3 mm 24 65 X 3 24
10. DN coss Everything s Digital 960H Indoor Dome Camera DWC D562D DWC D562DIR User Manual ABOUT MANUAL O60 Va ue Before installing and using the camera please read this manual carefully Be sure to keep it handy for future reference 11192012 PRECAUTIONS Do not open or modify Do not open the case except during maintenance and installation for it may be dangerous and can cause damages Do not put objects into the unit Keep metal objects and flammable substances from entering the camera It can cause fire short circuits or other damages Be careful when handling the unit To prevent damages do not drop the camera or subject it to shock or vibration Do not install near electric or magnetic fields Protect from humidity and dust Protect from high temperature Be careful when installing near the ceiling of a kitchen or a boiler room as the temperature may rise to high levels Cleaning To remove dirt from the case moisten a soft cloth with a soft detergent solution and wipe Mounting Surface The material of the mounting surface must be strong enough to support the camera COMPLIANCE This equipment has been tested and found to comply with the limits for a Class digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment This equipment generates uses an
11. ITOR MODE 1 MODE 2 MODE 1 is the default If the displayed image is not adequate try MODE 2 LANGUAGE A total of 10 different languages are supported ENGLISH MANDARIN CHINESE 1 CANTONESE CHINESE 2 JAPANESE DEUTSCH FRENCH ITALIAN RUSSIAN SPANISH AND DUTCH OSD COLOR A total of 8 menu colors are available BLUE GREEN CYAN RED MAGENTA YELLOW PURPLE AND GRAY COMMUNICATION OFF ON If ON is selected you can define the following EC TUF Coe PROTOCOL PELCO D only HL M esr CAMERA ID Provide the ID no on the camera 0 255 HE wee BAUDRATE 9600bps is the default There are a of total of 4 choices 2400bps 4800bps 9600bps and 19200bps FACTORY SET If selected the camera reverts back to factory default settings Note FACTORY SET does not affect the LENS DAY amp NIGHT CAMERA ID and DPC settings EXIT JUMP SAVE amp EXIT Exit the OSD after saving the current settings EXIT Exit the OSD without saving 23 EXIT EXIT SAVE amp EXIT Exit the OSD after saving the current settings EXIT Exit the OSD without saving 24 DW TROUBLESHOOTING Before sending your camera for repair check the following or contact one of our technical specialists No VIDEO Check the coaxial cable and make sure it is connected securely Check the lens iris adjustment on the menu setup of the camera Check the power supply and make sure the camera has the proper voltage and current
12. d radiates radio frequency energy and if it is not installed and used in accordance with the instruction manual it may cause harmful interference to radio communications WARNING Changes or modifications are not expressly approved by the manufacturer DW Table of Contents of Contents Introduction Features 4 Parts and Descriptions 5 Dimensions 6 Installation Included Accessories 7 Easy Installation 8 Base Installation 9 Connecting to Monitors 10 Adjusting the Camera 11 Adjusting the 3 Axis Gimbal 12 Camera OSD Menu and Glossary 13 24 Troubleshooting 25 Warranty Information 26 27 Specifications 28 29 FEATURES DWC D562D DWC D562DIR 1 3 960H High Resolution CCD 700 TV Lines 2 8 11mm Varifocal Auto Iris Lens Electronic Day and Night HME Highlight Masking Exposure AGC SMART BLC AWB Night Up Mirror Image Control Programmable Privacy Zones 8 amp Motion Detection Easy Icon Driven OSD Menu with Built In Joystick Auto Sensing 12VDC or 24VAC with Line Lock Secondary Video BNC Output Video Test Output Included 85ft Range IR with Intelligent Camera Sync DWC D562DIR only PARTS amp DESCRIPTIONS DW e Lens Power Input Connector 12VDC 24VAC Dual Voltage Video Output Connector BNC o Upper Case Q Dome Cover 6 Control Board Joystick Power Board Camera Base Mounting Screws DIMENSIONS IN MILLIMETERS INCHES
13. ess on sides of the image NIGHT UP OFF ON Adjusts sensitivity in low light conditions by set up level If ON is selected the set up level becomes higher and the images become brighter EXIT JUMP SAVE amp EXIT Exit the OSD after saving the current settings EXIT Exit the OSD without saving 19 The camera can detect movement and display an alarm on the screen when movement is detected AREA SET AREA 1 2 3 4 OFF ON If ON motion areas can be selected and moved accordingly Select Areas 1 4 and adjust using controls for TOP BOTTOM LEFT or RIGHT vide DE I d a MOT OM AREA oa BETES SENSITIV 1 30 Sensitivity level of motion detection is adjustable Motion dectection will be more sensitive at a higher number SHOW INDI OFF ICON TRACE _ Set the Show Indicator to OFF ICON or TRACE If ICON is selected a bell will appear in the upper right hand corner when motion is detected If TRACE is selected the area where motion was detected will be highlighted uOcTION EXTER OUT EXTER OUT Bu OFF ON ALARM SIGNAL EXTERNAL OUTPUT RETO If ON is selected you can set how long the alarm is displayed on the screen when motion is detected 0 15 seconds EXIT JUMP SAVE amp EXIT Exit the OSD after saving the current settings EXIT Exit the OSD without saving 20 E on i TT RR RR RR a ze AAF EX
14. light conditions It allows for clearer images even at night Exit the OSD after saving the current settings Exit the OSD without saving DW WB MODE AWC Auto White Balance Control mode compensates for color temperature changes between 2000K and 18000K 1 ATW Auto Tracking White Balance Control mode irum compensates for color temperature changes between 2500K 9500K iT JUMPS MANUAL Users can control the white balance manually by changing RED GAIN and BLUE GAIN see below PUSH LOCK Push Lock fixes the white balance based on current lighting RED GAIN 0 255 Adjusts the amount of red in the image BLUE GAIN 0 255 Adjusts the amount of blue in the image COLOR MODE NORMAL Color is similar to actual color COOL Color has more blue WARM Color has more red EXIT_JUMP SAVE amp EXIT Exit the OSD after saving the current settings EXIT Exit the OSD without saving 17 NIGHT C 0 100 NIGHT A 0 100 EXIT JUMP SAVE amp EXIT EXIT 18 DAY NIGHT sms 5 CED D amp N MODE AUTO Camera switches between day and night automatically depending on light level Camera will stay in color mode when there is enough light Camera will switch to B amp W at night or other low light environments COLOR Camera always stays in day color mode B amp W Camera always stays in night mode If AUTO is selected please define the following settings BURST ON OFF
15. r antenna inadequate signal pickup maladjustment of consumer controls improper operation power line surge improper voltage supply lightning damage rental use of the product or service by anyone other than an authorized repair facility or damage that is attributable to acts of God 26 DW LIMITS AND EXCLUSIONS There are no express warranties except as listed The Warrantor will not be liable for incidental or consequential damages including without limitation damage to recording media resulting from the use of these products or arising out of any breach of the warranty All express and implied warranties including the warranties of merchantability and fitness for particular purpose are limited to the applicable warranty period set forth above Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the exclusions or limitations listed above may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state If the problem is not handled to your satisfaction then write to the address listed on the last page Service calls which do not involve defective materials or workmanship as determined by the Warrantor in its sole discretion are not covered Costs of such service calls are the responsibility of the purchaser 27 SPECIFICATIONS Image Sensor 9
Download Pdf Manuals
Related Search